Supply, Installation, Testing and Commissioning of various utilities with allied work at Oxygen Panel room, Microbiology Department and Fever OPD of H. B. T. Medical College and Dr. R. N. Cooper Mun. Gen. Hospital.

Amount

Supply, Installation, Testing & Commissioning of various utilities with allied work at Oxygen Panel room, Microbiology Department & Fever OPD of H. B. T. Medical College & Dr. R. N. Cooper Mun. Gen. Hospital.

Providing and fixing structural Profile decking sheet as per particular specification,with GI sheet, zinc coating not less than 275 GSM as per IS 277 and of yield strength 500 Mpa of approved make with specified Base Metal Thickness. The profile shall be structural decking profile having ribs & pitch as per the drawing referred with the embossments (shear groove) on top and side of the ribs for better composite action. The decking sheet shall be fabricated to required form as per the slab design and fixed with Galvanised Iron fasteners, self drilling screws, shear studs as per IS 1367, connectors etc. complete as per design, drawing and direction of Engineer-in?Charge. (Refer typical drwg).The sheet shall be filled with 75mm thick M25 grade concrete reinforced with 8mm dia. HYSD bars placed 150mm C/C both ways. Plan area of the sheeting shall be measured and paid. Structural steel frame work shall be paid seperately. With Base Metal Thickness (BMT) (excluding Zinc coat thickness) 1.00 mm thick Profile decking sheet

Providing, detailing, composite fabricating members like Trusses, N-girders, girders, bracings, supports, purlins, runners, and similar structural steel members fabricated using M.S. hollow tubular steel sections (circular & rectangular pipes), of TATA Structura Make or equivalent conforming to IS 1239 part 1 and 2 and of grade Fe 250 as per specifications and approved fabrication drawings (which are to be prepared by Contractor and got approved from Engineer), including transportion of the same to site, erection of structural steel members for all heights & at all levels, provision of necessary erection bolts, fixing bolts, nuts, washers, cleats, stiffeners, gussets, base plate, and all necessary operations like preheating as per specifications, straightening, bending, cutting, drilling, grinding, machining if specified, welding, grinding, removing the welding burr and preparing surface for painting with wire brush cleaning and applying two coats of epoxy red oxide zinc phosphate primer of 30 microns each and two coats of Epoxy Corrosion Resistant Enamel paint of 30 microns after fabrication including touching up with spray painting after erection etc complete as directed by Engineer In Charge.

Providing, detailing, fabricating and fixing at desired location using M.S. chequered Plates of any thickness and of grade Fe 250 as per specifications and approved fabrication drawings (which are to be prepared by Contractor and got approved from Engineer), including transporation of the same to site, erection at all heights and levels, provision of necessary erection bolts, fixing bolts, nuts, washers, cleats, stiffeners, and all necessary operations like preheating as per specifications, straightening, bending, cutting, drilling, grinding, machining if specified, welding, grinding and removing the welding burr and preparing surface for painting with wire brush cleaning and applying two coats of epoxy red oxide zinc phosphate primer of 30 microns each and two coats of Epoxy Corrosion Resistant Enamel paint of 30 microns after fabrication including touching up with spray painting after erection etc complete as directed by Engineer In Charge.

Providing and fixing the Chemical Anchor Fasteners as specified below of Hilti Make or equivalent confirming to IS 1367 (Part 3) at required locations and level including drilling the hole, cleaning with blow pump and anchoring the bolt with chemical as per manufacturers specifications etc. complete as directed by Engineer In Charge. M20 x 170 foil capsule (HVU) & M20 x 240 Rod

Providing and laying in position ready mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying and the cost of centering, shuttering, finishing and excluding reinforcement, includingadmixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.The Mix design as per particular specfications shall be got approved by Engineer-in-Charge before execution of the item.The rate shall include cost of all specified materials and operations at all levels and heights, including the cost of centering, shuttering and and excluding reinforcement which shall be paid under relevant item.(Note :- Cement content considered in this item is @ 300 kg/cum as per IS 456 table showing minimum cement content. No extra will be paid nor any amount will recovered on account of variation of cement in mix design as per specifications for controlled concrete) Foundations, footings, bases of columns, rafts, pilecap

Providing and fixing in position uPVC/SWR (Soil/Waste/Rain) pipe of type-B 160 mm dia. in any position including all fittings and accessories, making joints / connections water tight with solvent cement, scaffolding if necessary and making good the damages if any (excluding excavation and refilling the trenches) etc. complete as specified and directed.(All fittings and accessories like clamps,etc. should be of same brand. No separate payment shall be made for fittings and accessories).

M-10 grade plain cement concrete (cement content considered @ 220 kg/cum as per IS 456 table showing minimum cement content)

Providing and constructing raised platform of 750 mm wide and 600 to 750mm high using minimum 40mm thick polished kadappa stone slab base with minimum 15mm thk. polished stone top as specified below of approved quality, colour and texture, supported by both side polished, 40mm thk. and minimum 700mm wide kadappa spaced at not more than 1200mm clear, including polished facia of min. 100mm height as specified below with champhered/ rounded at the top edges, jointing in approved adhesives, machine cutting, making opening for sink and fixing the same in position, leveling, smooth cement plastering along the sides to match the existing surface in cement mortar, filling the joints with pigment mixed with cement, cleaning, finishing, curing etc complete as directed by Engineer In Charge.Ruby red / jet black / Hasan green Granite slab at top and facia

Providing and laying polished natural stone strips upto 100mm wide as specified below (Machine cut) 25-30 mm. thick of an approved quality and size for paving /flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cement float, machine cutting, dressing, leveling, jointing, filling the joints with neat cement slurry or with required pigment, machine polishing at site, curing, finishing, etc complete as directed by Engineer In Charge.

P/F Aluminium composite sheet of 3 mm thick either suspended or fixed bracketed on wall with U.V digital printing at suitable locn including all necessary framework completed as per detailed drawings to be issued during construction & as directed by the engineer

Providing & fixing of Door handles

Providing and fixing mortise lock of approved make manufactured as per IS:2209 and 6607 and as described below for doors with necessary fixtures and materials and labour etc. complete.

KRUPASINDHU ENGINEERS PRIVATE LIMITED