Provn of Guard Room and Sentry Post near Bldg No P-203 at CVD and Provn of certain sanctioned Minor works in the area of AGE B/R-II and AGE E/M under GE (West) Delhi Cantt-10

Surface excavation in soft /loose soil not exceeding 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed by Engr-in-Charge.

Excavation in trenches width n'exc 1.5 m and not exceeding 1.5m deep and getting out in soft / loose soil all as specified and directed.Note:- Insurance of workmen & cleaning of site, removal of all hinderance's/obstractions unforseen item, Electric cable, Gas Pipe line etc permisssion from other department should be responsibility of contractor (MES will only assist in getting permission etc) restoring and getting the same constructed/Repaired/Replacement complete & nothing extra shall be payable.

Excavation over areas not exceeding 1.5m deep and getting out in soft/ loose soil all as specifed.

Excavating over areas exceeding 1.5m but n. exc 3.00m in depth and gating out in soft/ loose soil all as specifed.

Excavating over areas exceeding 3.00m but n. exc 4.50m in depth and gating out in soft/ loose soil all as specifed.

Material and labour for brickwork with sub class `B' bricks in one brick thick honey comb walling, built in cement mortar 1:3 complete all as specified and as directed.

M&L for loose filling with broken bricks aggregate of gauge 40 to 80mm in soakage pits, soakage wells complete all as specified and as directed.

Returning filling in layers including leveling watering and well ramming in layers n.exc 25 cm thick compelte all as specified and directed.

Removing surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate ) as in foundation filling, sub base for floors etc complete all as specified and directed by Engr-in-Charge.

M&L for old size burnt Brick work with sub class 'B' old size bricks straight or curved on plan exc 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per Serl Item No 11 here in before but half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Use & waste of formwork to sides of concrete foundations,footings,bases or column,raft and raft beams,sides and soffits if any of foundations and plinth beams and similar work,vertical or batter for flat rough finished surface of concrete complete all as specified and directed by Engr-in-Charge.

Use & waste of formwork to sides of pillars,posts,struts,piers,columns and stanchions etc rough finished for square/rectangular or polygonal surfaces of concrete complete all as specified and directed by Engr-in-Charge.

Use & waste of formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressummers, lintels, cantilever, shelves including supports, overhangs, etc also splays between floors and beams etc rough finished flat surfaces of concrete all as specified and directed

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough flat finished surfaces of concrete complete all as specified and directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for RCC (Designl mix) M-25 (20mm graded aggregate) as in foundations including rafts,footings,foundations beams ,bases of column etc complete all as specified and directed by Engr-in-Charge.

M&L for RCC (Design mix) M-25 (20mm graded aggregate) as in columns, pillars,piers,posts and struts etc complete all as specified and directed.

M&L for RCC(Design mix) M-25 (20mm graded aggregate) as in beams, cantilevers,bressummers,lintels over 1.5 m span complete all as specified and directed by Engr-in-Charge.

M&L for RCC(Design mix) M-25 (20mm graded aggregate) as in slabs supported on walls,beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge.

M&L for RCC(Design mix) M-25 (20mm graded aggregate) as in Chhaja complete all as specified and directed by Engr-in-Charge.

M&L of TMT bars 10 mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Ditto all as per item No 23 above but 5 mm dia and over upto and including 10 mm dia in stirrups spaces and binders complete all as specified and directed.

M&L for 15mm thick cement plaster in cement mortar 1:4 on brickwork or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for 10mm thick cement plaster in cement mortar 1:6 on brickwork or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement all as specified and directed by Engr-in-Charge.

M&L for Preparation of new plastered surfaces wall and applying two coats of Oil bound distember over and including a coat of chalk whiting primer complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying two coats of cement base paint over and including a coat of chalk whiting primer complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified and directed.

M&L for Preparation of new or previously untreated steel surface, n exc 10cm width or girth when unconnected with other painting or when painted in a different tint applying two coat of synthetic enamel paint

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for hard core of broken stone or boulders gauge n.exc 63 mm deposited spread and leveled in layers n.exc 15 cm thick watered and ramed to a true surface complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate ) as in sub base for floors etc complete all as specified and directed by Engr-in-Charge.

M&L Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bedding 15mm thick in cm(1:4) complete all as specified and directed.

M&L Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with pigment with colour of tiles over and including screed bedding 15mm thick in cm(1:4) complete all as specified and directed.

M&L for glazed coloured designer ceramic tiles of size 350x250x7mm/ 450x350x6mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry over and including 10mm thick rendering in cement mortar (1:3) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engr-in-Charge.

S&F Aluminium door single leaf with powder coated aluminium frame of section 62.5x37x1.5mm thick, shutter with bottom & middle rail of section 112.50x 37x1.5mm thick and styles & top rail of section 83x37x1.5mm thick with centrally locking arrangement with lock make of ‘GODREJ’ or ‘LINK’ 7 lever and self closing device with rebate including jointing cleats, fixing of builders hardware fittings, necessary numbers of floor spring and glazing/gauge with 5mm thick glass including necessary fittings, fixtures & aluminium snap beads, (Note : Measurement shall be taken clear opening ie out to door frame as a whole including all fittings and fixtures and no extra shall be paid separately). Cost of glass and wire cloth included herein complete all as specified and directed by Engr-in-Charge.

M&L powder coated aluminium 50 micron anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5 mm thickness and of shutter size 40mm x 18mm (with 9.00 mm interlocking legs) x 1.45 mm thick section, including frame size 100mmx44mmx2mm thick, including 95mm aluminium handle with spring lock, stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4 mm and fixed with steel wire stapples 5mm thick plain glass including necessary fitting/fixture/aluminium snap beads, EPDM rubber , neoprene packing, rollers to slide track window complete all as specified. (Note : Measurement shall be taken clear opening ie out to window frame as a whole including all fittings and fixtures and no extra shall be paid separately). Cost of glass and wire cloth included herein complete all as specified and directed by Engr-in-Charge.

S&F for powder coated aluminium grill of powder coating of minimum 50 micron with aluminium mesh of size 50 mm x 50mm with square tube solid 6mm thick including aluminium channel of suitable size to the aluminum window complete all as specified and directed by Engr-in-Charge.

S&F for powder coating aluminium two way track ventilator, without sash bar with aluminium section of weight 0.55/RM including aluminium handle with spring lock, stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4 mm and fixed with steel wire stapples 5mm thick plain glass including necessary fitting/fixture/aluminium snap beads, EPDM rubber , neoprene packing, rollers to slide track window etc. complete all as specified and as directed. (Note : Measurement shall be taken clear opening ie out to ventilator frame as a whole including all fittings and fixtures and no extra shall be paid separately). complete all as specified and directed by Engr-in-Charge.

S&F 4mm thick Figured glass, pin head type and glazing with oil putty in sqm n exc 0.5 sqm in each pane fixed in bottom two pane in windows etc complete all as specified and directed.

S&F Solid PVC door frame of size 50x47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supplying and fixing as per specification complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail either side & as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm butt hinges medium weight cold rolled fixed to doors with SS screws complete all as specified and directed.

S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F 125mm long aluminium handles cast type anodised ISI Marked complete all as specified and directed.

S&F Vitreous china white wash down water closet (pedestal pattern) including PVC seat cover and connection to drain or out going pipe and to flushing pipe anti-syphonage pipe etc, complete all as specified.

S&F 10 ltrs capacity PVC valveless syphonic action type low level flushing cistern complete with syphonic handle lever PVC bend including connecting to WC and fixing on walls with bracket complete all as specified and directed.

S&F in repair 15mm dia brass chromium plated centre hole mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including connection pipe and fittings complete all as specified and directed.

S& F Bib tap of cast copper alloy brass but fancy type, Chromium plated 15mm bore, with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 1000 litres capacity rotational moulded, triple layer polyethylene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roof including fittings complete all as specified and directed

S&F Gun-metal, globe or gate valves 20mm dia bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 gms) and fixed complete all as specified and directed

S&F 15mm bore stop/angle valve cast copper alloy with crutch or butterflty handle, screwed down screwed high pressure for iron pipe or for brass ferrule fancy type chromium plated with fancy shank and cup complete all as specified and directed by Engr-in-Charge.

S&F PVC Connection pipe, 450mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified.

S&F 600 mm long Tubular towel rail brass chromium plated 20mm dia fixed to wall with steel screws and PVC rawl plug complete all as specified and directed.

S&F Health Faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed by Engr-in-Charge.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and directed by Engr-in-Charge.

S&F Vitreous China bowl urinal flat back, size of 465x355x265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, and flush pipe ) including waste pipe 32mm dia bore complete all as specified and directed by Engr-in-Charge.

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) pipe of pressure not less than 4kg/sqcm in single socketed, in any length with rubber ring joints,fixed to wall including distance pieces and stack clamp with nuts and bolts complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipe of pressure not less than 4 Kg/Sqcm in single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm bore PVC(SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F 75mm bore PVC(SWR) bends any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) 'S' trap complete all as specified and as directed.

Supply and laying 20mm outer dia of CPVC pipe SDR11 fittings in trenches, wall and ceiling including fittings including taking down old steel tubing etc complete all as specified and directed.

Supply and laying 25mm outer dia of CPVC pipe SDR11 fittings in trenches, wall and ceiling including fittings etc including taking down old steel tubing complete all as specified and directed.

S&F 20mm CPVC brass elbow complete all as specified and directed .

S&F 25mm CPVC brass elbow complete all as specified and directed .

S&F 20mm CPVC brass elbow (3/4 x 1.2)complete all as specified and directed.

S&F 20mm CPVC Tee complete all as specified and directed.

S&F 25mm CPVC Tee complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified.

M&L for Cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection, 75mm thick, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for cement concrete 1:3:6 type C2 with using 40 mm graded stone aggregate as in concrete bed to drain pipe 150 mm dia including packing under and haunching against the sides of pipe after they are laid and tested completed all as specified and directed by Engr-in-Charge.

M&L for 150 mm nominal size Double wall corrugated HDPE pipes stiffness class SN 8 high density, polyethylene pipe resistent to chemicals, easy and light weighted, long living, low friction, flexible, sun resistant pipe and laid in trenches including taking down of any type of old pipe complete all as specified and as directed.

Factory made 75mm thick SFRC manhole/ Drain covers with frame (heavy duty) HD-20 graded designation, confirming to IS-12592, area not exc. 0.90 Sqm each, fixed in cement concrete 1:2:4 using 20mm graded stone aggregate complete all as specified and directed.

M&L Granite 18 to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over & including 15mm thick screed in cement mortar (1:4) with pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F Mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws complete all as specified and directed.

S&F Rolled mild steel Fe 410 -W (Gde- E- 250) quality- A in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete complete all as specified and as directed.

S&F Pre painted galvalume alumimium zinc coating GI based corrugated/crimped steel sheet 0.5mm thick(AZ150,150GSM green colour) of any colour having tensile strength of 550 Mpa in roof covering, fixed with self tapping screws complete all specified and directed.

M&L for 75mm thick Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base of floors finishes complete all as specified and directed

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping/bed block including weathering slightly rounded or chamfered angles and throating as directed and including necessary form work required complete all as specified and as directed.

M&L 10 mm thick screed bed or bedding layer of mortar in CM(1:4) with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface. Note: WPC shall be measured and paid separately

Supply only water proofing compound complete all as specified and as directed.

M&L for applying two coat of Bitumen primer blown any grade, applied hot, to concrete surfaces at the rate of 1.5kg. per sq. m per coat APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as directed.

Supply and fixing Heat Resistant Terrace Tiles(300mmx300mmx20mm) with SRI(solar refractive index)>78,solar reflection>0.70 and initial emittance>0.75 on waterproof and sloped surface of terrace,laid on 20mm thick cement sand mortar in the ratio of 1:4 (1 cement:4coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1,including rubbing and polishing of the surface upto 3 cuts complete,including providing skirting upto 150mm height along the parapet walls in the same manner complete all as specified and directed.

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegetation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified and directed by Engr-in-Charge.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified and directed by Engr-in-Charge.

Removing mud phuska/soil material exc.250 m but n exc. 500 m and depositing complete all as specified and directed by Engr-in-Charge.

M&L for brushing neat cement slurry with 3 kg of cement per square metre complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:2:4 type B0 (using 12.5 mm graded stone agg) cement concrete as in roof padding etc.complete all as specified and directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces complete all as specified and directed by Engr-in-Charge.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric(wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified by Engr-in-Charge.

Taking down door/window/ventilator frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down door/window/ventilator frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and directed by Engr-in-Charge.

S&F Steel Ventilator with top hung shutter including hinges,steel peg stay,complete all as specified and directed by Engr-in-Charge.

S&F steel window with side hung shutters including projecting type hinges with steel handle,and steel peg stay,complete with glazing bars,dovetailed or welded complete all as specified and directed by Engr-in-Charge.

All as per item no.103 but without glazing bars.

S&F mild steel framed work such as grills/guard bars, cooler stand, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290(Gde-E-165) complete all as specified and directed by Engr-in-Charge.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-Charge.

S&F fibre glass reinforced plastic (FRP) door frame shall be three legged of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness. The laminate door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibre glass from all sides. MS stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engr-in-Charge.

S&F FRP door shutter 30mm thick glass fibre reinforced plastic (FRP) moulded door shutter of required colour and approved brand and manufacturer made with fire retardant grade unsaturated polyester resin moulded to 3mm thick FRP laminate for forming hollow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP laminate for panels and confirming to IS 14856-2000 including fixing in the frame at site complete all as specified and directed by Engr-in-Charge.

S&F 125 mm long stainless steel door handles 'D' curve ISI Marked complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long high grade durable stainless steel barrel tower bolt of extruded section complete all as specified and directed by Engr-in-Charge.

Demoltion of brick work built in cement mortar of any specification and in any position complete all as specified and directed by Engr-in-Charge.

Taking down of cement or cement lime plaster, any description including racking out joints,hacking for key,scrubbing down with water, complete all as specified and directed by Engr-in-Charge.

Dismantling of floor,hearth or wall tiling incl mortar bedding and throw rubbish out the premises as directed by the Engr-in-Charge.

Demolition of unreinforced cement concrete in ground floor and pavings n.exc. 15 cm thick (below or above GL) complete all as specified and directed by Engineer in Charge

M&L for Plain cement concrete 1:2:4 type B -1(20 mm graded aggregate) all around the interlocking tiles to fix in position as in kerbs Complete all as specified and directed by Engr-in-charge

S&F Vitreous China bowl urinal flat back, size of 465x355x265 mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs,bedding urinal against wall in cement moratr 1:2,securing urinal to plugs with and including 60mm long brass screws,pointing around urinal back in cement; urinal spader, pvc connection 300mm long 15mm size and Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq.cm as a waste pipe fixed in repairs complete all as specified and directed by Engr-in-Charge.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests(excluding flushing cistern), including flush pipe of polyethlene of low or high density,connection to trap,and to flushing pipe,anti-syphonage pipe,etc. complete trap set in concrete and including supply and fixing 100mm cast iron sanitary connection socket fit WC outlet complete all as specified and directed by Engr-in-Charge.

S&F in repair 100mm bore cast iron 'P' Traps complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC flushing cistern 10 Ltrs capacity white valveless, syphonic action type flushing cistern, low level with inlet ball valve, float and handle, including brackets and flush pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm dia brass chromium plated centre hole mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including connection pipe complete all as specified and directe by Engr-in-Charge.

S&F in repair angle valve 15mm bore dia brass chromium plated fancy type, screwed down, new high pressure with lever type , chromium plated for iron pipe or unions complete all as specified and directed by Engr-in-Charge.

S& F in repair 15 mm fancy type chromium plated bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

S&F brass chromium plated soap dish fancy type fixed to wall with CP brass screws complete all as specified and directed by Engr-in-Charge.

S&F in repairs chromium plated brass overhead shower rose 125 mm size swivel type with long chromium plated arm rod including fixing to steel pipe or union complete all as specified and directed by Engr-in-Charge.

S&F tubular towel rail, 20mm dia 'D' type 60cm long between flanges including a pair of CP brass bracket, complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC connection pipe 600mm long and 15mm size with brass nuts complete all as specified and directed by Engr-in-Charge.

S&F 32mm dia PVC waste pipe 90 cm long for urinal,WHB etc complete all as specified and directed by Engr-in-Charge.

S&F in repairs stop valve 15mm bore fancy type chromium plated, with long shank and cup (concealed type),cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.

S & F 500 Ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I & dismantling existing water storage tank, complete all as specified and directed by Engineer in Charge.

S&F 15mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 gms) and fixed complete all as specified and directed by Engr-in-Charge.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

Dismantling CI pipe alongwith fittings of 50/75/100mm dia,below or above ground level or laid in floors,jointed in cement mortar and taking out complete all as specified and directed by Engr-in-Charge.

S&F 110mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified and directed by Engr-in-Charge.

S&F PVC(SWR) vent cowl,for 110mm bore pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair brass chromium plated grating 100mm dia withiout waste hole,complete all as specifed and directed by Engr-in-Charge.

Demolition of reinforced cement concrete as in Chajja, RCC parapet, Kitchen slab, Chullah hood, chimney portion and similar work concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Cutting holes in brick walls in cement mortar for inserting hold fast and similar works etc. and making good to dismentalled portion in CM 1:3 or cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in wall exc half brick but n exc one brick thick complete all as specified and as directed.

S&F rolled mild steel work in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed.

S&F of Fe 410-W(Gde-E-250) quality-A mild steel plates, plain or chequered , 5mm thick or over in thickness in available sizes complete all as specified & directed.

M&L for Providing precast ce-ment concrete TYpe C1 1:3:6(20mm graded aggregate) in posts, lintels, bressumers, steps, quoin blocks (for use with masonry), copings. kneelers, pier caps, columns, , bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar 1:4 complete with joints to match complete all as specified and as directed.

M&L for Providing precast cement concrete Type C0 1:3:6(12.5mm graded crushed stone aggregate) louvres and jallies, 25mm thick (measured solid) ,Set in cement mortar1:4 including all mould-ings complete all as specified and directed.

S&F PVC insulation panels Thickness of of PVC insulation panel 10mm with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling including grid made of Aluminium complete all as specified and as directed by engr in charge

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M&L for Excavation in post holes (or similar holes) each n exc 0.50cum, getting out in hard/dense soil, returning, filling, in and ramming earth or broken rubble mixed with earth around, in layers n.exc. 25cm, watering and removing surplus soil to a distance n.exc. 50 m and making good surface in hard/dense soil complete all as specified and directed.

M&L for Cement concete 1:2:4, type B-2 (40mm graded aggregate)as in foundations,filling and mass concrete complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified.

S&F Rolled mild steel work in sections as in post/ pillers where connnected with angle cleats or other connecting plates etc, of Fe 410-W (Gde E-250) Quality 'A' including fabrication, erection and fixing complete all as specified and directed by Engr-in-chagre.

S&F Rolled mild steel in Roof trusses (framed ), trussed,purlin, crane gantries , rails and fastenings and heavy bracket framing(beam,tee,angles,channel or flat sections ) including distance pieces , cleats etc. of Fe 410-W (Gde E-250) quality 'A' including fabrication, erraction and fixing complete all as specified and directed by Engr-in-charge.

M&L for hardcore of broken bricks of gauge n.exc 63mm, deposited spread and leveled in layers n.exc 15cm thick watered and rammed to a true surface below interlocking tiles and in sunken floor complete all as specified.

M&L for 100mm thick PCC 1:4:8 type D-2 40mm graded stone aggregate as in sub base of floors finishes complete all as specified and directed.

M&L for 50mm thick PCC(1:2:4) type B-1 (using 20mm graded stone aggregate) as in flooring complete all as specified and directed by Engr-in-Charge.

S&F Solid PVC door frame of size 50x47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supplying and fixing as per specification complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail either side & as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Vitreous China squatting pan, ‘Orissa’ pattern' size 580 x 440 mm white with integral foot rests (excluding flushing cistern), including flush pipe of polyethylene of low or high density, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete trap set in concrete and including CI 'P' Trap & 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and directed.

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F 500 litres capacity rotational moulded, triple layer polyethylene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roof including fittings complete all as specified and directed by Engineer in Charge.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed by Engr-in-Charge.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed by Engr-in-Charge.

S & F salt glazed stonewire drain pipe 150 mm internal diameter grade A laid in trenches jointed and tested complete all as specified and directed.

Cutting into existing manholes for connecting new drains 150mm dia,making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required complete all as specified and directed by Engr-in-Charge.

M&L preparation of old decorated plastered surfaces by complete removal of existing treatment & applying two coats of cement base paint on walls complete all as specified & directed.

M&L for preparation of old decorated plastered surfaces of walls etc by complete removal of existing treatment including washing, rubbing down and stopping of surface and applying two coats of oil emulsion distemper over and including a coat of primer on wall surfaces complete all as specified and dircted.

M&L preparation old plastered surfaces of ceiling and applying one coats of white wash all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Taking down old MCCB , TPN DBs , SPN DBs, sp mcb & main switch/ enclosure box of any make and type from the site and making good surface complete all as specified and directed.

M&L for concealed point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid PVC conduit medium grade ISI Marked and all conduit accessories concealed in wall/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated single core copper cable FRLS as earth continuity conductor, fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing modular switches, socket outlet and fan regulators etc. all as specified and directed :-

(a) One light/fan/bell/Exhaust fan/Fresh Air Fan point controlled by one way switch 5 amps.

(b) One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board.

(c) One 3 pin 5 Amps socket outlet point controlled by one way switch on same board along with other switches.

All as per item No 172 above but with single core copper conductor cable FLRS 2.50 sqmm for one 3 pin AC Box outlet,20 Amps concealed and including provision of 2.50 Sqmm PVC insulated single core copper conductor cable as earth continuity conductor on independent board.

M&L for concealed point wiring with insulated unsheathed multistranded FRLS copper conductor in non-metalic rigid PVC conduit but with single core copper conductor cable FLRS 4.0 sqmm for one 3 pin AC Box outlet 20 Amps concealed and including provision of 4.0 Sqmm single core PVC insulated copper conductor cable as earth continuity conductor on independent board.(For AC point)

S&F Modular switch 1 way 6A,1 module, 230V, 50 Hz complete all as specified and directed.

S&F Modular switch 1 way 16A,1 module, 230V, 50 Hz complete all as specified and directed.

S&F Modular socket 6A, 3 pin combined 2 module,230V, 50 Hz complete all as specified and directed.

S&F Modular socket 6A/16A - 2/3 pin combined 2 module, 230V, 50 Hz complete all as specified and directed.

S&F Modular ceiling fan regulator, step type for BLDC ceiling fan 1 or 2 module.

S&F ceiling fans complete with blades, down rod, regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply, laying and drawing submain wiring in and including 20 mm dia concealed PVC rigid conduits including cutting of chases for laying conduit making good the disturbed surfaces as per existing surfaces or as directed on walls 02 runs of IC x 6.00 sqmm (Main Cable and neutral) and one run of IC x 6.0 sqmm (as earth wire) of multistranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforing to IS : 694 of 1990 complete including taking down existing old wire all as specified and directed. Note :- Two runs of IC x 6.00 sqmm (Phase wire and neutral ) and one run of IC x 6.00 sqmm (as earth wire) will be measured as one unit length.

S & F sheet metal enclosure MCB DB TPN 4 way with 100 Amps rated copper bus bar 415 volts with metal double door, IP-43, with provision for FP MCB/Isolator/RCCB/RCBO as incomer and SP MCB's as outgoings, including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good the disturbed surface to match with existing one, complete all as specified and as directed.

S&F MCB TPN 63 A,10 kA 'B' curve, 415 V complete all as specified directed.

S&F of factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 10 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 all as specified and directed. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of factory made epoxy polyester powder coated distribution board SP & N 4 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 2 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 including taking down old DBs all as specified and directed. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 complete all as specified and directed.

S&F in replacement MCB SPN 32 to 40 Amps rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

S&F of single pole MCB 32 to 40 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 complete all as specified and directed.

Supply and fix LED batten luminaire surface mounted, 4 feet system wattage of 20 Watts with lifetime of 25000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 10%, colour temperature - 6500K, surge protection 2.5KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level ≥ 100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed.

S&F in repair surface mounting LED Batten 20W LED light. Fixture should have minimum efficacy at system level >=100 lumens/Watt, life of fixture not less than 50K Hrs,CCT 4000-6500K & CRI>80, PF≥0.90. An operating voltage Range of 140-270V including all connection upto ceiling rose complete all as specified and directed.

S&F surface mounting LED Integrated Aluminium Batten luminarie Polycarbonate co-extusion tube 10W LED light 2 ft housing. An operating voltage Range of 140-270V including all connection upto ceiling rose complete all as specified and directed.

S&F of 35 watts 230 V AC outdoor type with High efficient LED Building security light fitting with high pressure die cast Aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP: 65/66 protected complete with bracket made out of 32 mm GI pipe light grade 1.2 mtr long bend to shape with clamps and fixing bolts all as specified and directed.

S&F of Fresh Air Fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm sweep, single phase,including cutting of holes in wall/windows for fixing the fresh air fan complete all as specified and directed.

S&F exhaust fan metallic type ventilating single phase 230/240 V Of 300 mm sweep with louver shutter including cutting of holes in a round shape and including fixing the ventilating fan complete all as directed and specified.

S&F of 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP 65 Protection, System level efficacy of the Luminary is =>90 lm/W, Power Factor =>0.90, Colour Temperature 3000K-6500K, including connecting up with necessary PVC sheathed 3 core 1.5 Sqmm copper conductor flexible wire fixed complete all as specified and directed.

S&F of ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed.

M&L for modular AC Box with 20A SP mini MCB, plastic enclosure & unbreakable Heavy Duty ISI mark Plug top complete for AC & geyser point set dully concealed in wall complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate 600X600X6 mm thick buried directly in ground (earth pit not les than 2.25 M deep below GL with top edge of plate not less than 1.50 m below GL) connected with GI earth lead wire 4.0 mm as earthing leads by means of bolts, nuts, check nuts and washers all joints as shown on drawings and including excavation, earth work. GI pipe light grade 15 mm bore for protection of GI earth wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt PCC (1:2:4) type B1 chamber and MS angle iron frame of 40mmx40mm x3 mmand RCC cover 40 mm thick (1:2:4) type B1 using 20 mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in electrical plate No 3 of SSR Part -I and conected to earth test point including testing complete all as secified and directed at site.

Supplying, laying, jointing and testing cable XLPE insulated IS 7098 (Part-I)-1988 marked, screened, PVC sheathed, armoured electric power cable (heavy duty) with aluminium conductor for working voltage upto and including 1100 volts, cross sectional area of cable 25 sq mm 3.5 core laid in trenches/fixed on pole/wall/passed through pipe complete all as specified and directed by Engr-in-Charge.

Supplying, laying, jointing and testing cable XLPE insulated IS 7098 (Part-I)-1988 marked, screened, PVC sheathed, armoured electric power cable (heavy duty) with aluminium conductor for working voltage upto and including 1100 volts, cross sectional area of cable 10 sq mm 2 core laid in trenches/fixed on pole/wall/passed through pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair, 1100 volts grade heavy duty cable with PVC insulated aluminium stranded conductor served with an inner sheathing of PVC armoured, PVC sheathed 6 sq. mm nominal cross section, 2 core.

Supply,laying in repairs of PVC under ground XLPE insulated heavy duty electric cables armoured with aluminium conductor, 1100 volts grade, cross sectional area 16 sqmm 2 core laying in trenches, fixed along wall, through GI pipe under floor complete.

supply and fix GI pipe 32 mm dia light grade , for laying in rod crossing /fixing of vertically complete all as directed.

M&L for sand cushioning the UG cable screened unwashed river sand and punning for cushioning to cable all as directed.

M&L for laying dry bricks old size with subclass 'B' made of burnt clay best quality locally available with permissible tolerance, laid straight trench for protection of cable all as specified and directed