Different works of Extension, Renovation and Modernization of (ERM), Sukla Irrigation Project under PMKSY-AIBP for the year 2021-22 _Group No.104

Amount

Construction of office buliding of Assistant Executive Engineer, Suklai-Serfang Sub-Division (Irrigation), Naokata Normal preparation of site

Earth work in excavation for foundation trenches of walls retaining walls footings of column, steps, septic tank etc including refilling (return filling) the quantity as necessary after completion of work watering and ramming etc and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. A) Up to depth of 2.00m below the existing ground level (a) In ordinary soil

Providing brick soling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and necessary dewatering, complete. (a) Brick on flat soling

Plain cement concrete works with coarse aggregate of size 13mm to 32mm in foundation bed for footing steps, walls brick works etc. as directed and specified including dewatering if necessary and curing complete (shuttering where necessary shall be measured and paid separately) (a) In prop 1:3:6

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete ( upto 1st floor level). a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: (a) Foundation footings bases of columns pile cap, raft and mass concrete works etc.

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: Sides of tie beams, plinth beams, grade beams etc. at orbelow plinth level (ii) Using 25mm thick plank

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: Column, pillars, posts & strut (a) Square, Rectangular, polygonal in plan or any shape like Teel/L etc. having plane vertical face (ii) Using 25mm thick plank

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: Column, pillars, posts & strut Sides and soffits of beams, beam haunching, cantiliver girders, bressumers, lintels and horinzontal ties (ii) Using 25 mm thick plank

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: Column, pillars, posts & strutFlat surfaces such as soffits of suspanede floors,roofs, landings, cantiliver slabs, chajjas, balconies and the like. (ii) Using 25mm thick plank

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) I) Using Mixer Machine (A) In substructure up to plinth level Foundation footing columns with base tie and plinth beam grade beam pile cap base slab retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (A) M15 grade Concrete

Providing and laying plain reinforce cement concrete works in prop1:1.5:3(1cement:1.5 coarse sand :3 graded stone chips, 20mm down) including dewatering if necessary and curing complete but excluding cost of form work and reinforcement for reinforced cement conrete work (form work and reinforcement will be measured and paid separately) (B) In super structure from plinth level up to 1st floor level. (ii) Columns, pillars posts struts suspended floor, roof landing shelf and support balcony lintel sill band beam girder bressumer cantilever staircase including preparing of top surfaces and furnishing and nosing (a) M15 grade concrete

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in sub-structure up to plinth level. (b) In proportion 1:4

Earth/sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:2:4 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in prop. As recommended by the manufacture including curing etc. complete as directed.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In proportion 1:4

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). c) Delux range Somany/ Orient/Nitco/Qutone Make i) Of size 300mmx300mm and above

iii) Of size 600mmx600mm and above

ii) Of size 400mmx400mm and above

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). a) Normal range i) of size 200mmx200mm and above

15mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering upto 1st floor level including arises, internal rounded angles, not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

12mm thick cement plaster in single coat on fair side of single or half brick wall for interior plastering upto 1st floor level including arises, internal rounded angles, not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

Cement plaster skirting with cement morter in prop. 1:3 ( 1 cement :3 coarse sand ) finished with a floating coat of neat cement including rounding of junctions with floor. (a) 15 mm thick

Providing wood work in frame (chowkath) of doors windows clerestory windows and other similar works wrought framed and fixed on position in contact with C.C or brick masonry wall including supplying fitting and fixing with M.S hold fast (40mm x 3mm x 250mm) as per design embedded in cement concreter block in proportion 1:2:4 and with two coats of liricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (b) With 1st class timber (Bonsum/ Sundi)

Providing, fitting and fixing full panelled doors/ windows including oxidised M.S butt hinges (100mm x75 mm x3.55mm) with necessary screws (other fittings to be measured and paid separately ) (b) With 1st class local wood (Gamari/Hollock/Bonsum wood. (ii) 35 mm thick.

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. (a) 2 Track sliding window (i) 6 mm clear glass

Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws. (I) Plain grill (a) Fixed to Brick work/P.C.C./R.C.C.

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Providing corrugated galvd Iron sheet roofing of TATA shaktee / SAIL including fitting and fixing necessary galvd J or L hooks bolts and nuts 8 mm dia with bitumen washer 25mm dia x 3mm thick and 1.6mm thick limpet washer complete excuding cost of roof truss purlin etc. (roof trusses ad purlin etc. to be measured and paid separately. (e) 0.63mm thick

Providing galvd iron ridging of TATA shaktee / SAIL in including supplying. and fixing necessary galvd screws washers etc. complete as directd. (e) 0.63mm thick

Providing, fitting and fixing in position false ceiling of 6mm thick Bison panel (cement bonded particle board) on timber frame of 1st class local wood (Hollock/ Bonsum/ Sundi) of 50mm x 50mm spaced at not more than 1.20m apart , fixed to the wall at the end with necessary nails, wood screws, hooks,bolts etc. including painting (one coat primer and two coats of painting) as necessary complete as directed by the Department for all levels.

(a) Colour washing with lime on wall surface (two coats) over and including a priming coat of white washing to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and other foreign matter.

Providing two coats of acrylic water based wall putty/ wall filler of Asian Paints/ Berger/ Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and external after removing all the loosely adhering material from the wall/ ceiling surface with the help of emery stone, putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.

Applying priming coat over new wood and wood based surface over 100mm in girth/width after and including preparing the surface by thoroughly clearing oil grease dirt and other foreign matter, sand papering and knotting.

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt dust and other foreign matter sand papering and stopping. (i)surface over 100mm in width or girth. b) High gloss (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Nerolac)

Applying primary coat over new steel and other metal surface over 100mm in width or girth after preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. (a) With ready mixed "red-lead / red oxide" primer

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt dust and other foreign matter. (i) Surface over 100mm in width or girth. (b) High gloss (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Nerolac)

Supplying fitting, fixing anodized aluminum fittings of approved make reasonably smooth free from sharp edges and corners flaws and other defects and with counter sunk holes for screws including necessary aluminum screws etc. complete (anodized to bright natural matt & satin finished)(b) Tower bolt (200mmx12mm)

(c) Door handle (150 mm)

Supplying, fitting, fixing brass fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished ).j) Door latchesii) 250mm x 16mm x 5mm

Internal Electrification at AEE Office,Naokata Wiring for light/fan/call bell point with2x 1.5 sq-mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS 694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1.1 KV (Finolex/RR cable or equivalent make as approved by the Deptt.) in surface/recessed conduit wiring system with 20 mm dia 2mm thick/ heavy rigid PVC IS : 9537 Part-III conduit (Berlia/ AKG/Precision/Presto Plast/Polycab/MW orequivalent make as approved by the Deptt.) including 6 Amp flush type switch/bell push (Anchor penta/Gold medal/Kolor Kany Kom/Havells or equivalent make as approved by the Deptt.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover, ceiling rose (Anchor penta/Gold medal/Kolor Kany Kom/Havells or equivalent make as approved by the Deptt.) etc. complete.

a) Long point point up to 10.00 M length

Wiring to a 5 pin 6 Amps plug point with 1.5 sq-mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS 694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1.1 KV (Finolex/RR cable or equivalent make as approved by the Deptt.) in surface/recessed 2mm thick/ heavy rigid ISI marked IS : 9537 Part-III rigid PVC conduit conduit (Berlia AKG/Precision/Presto Plast/Polycab/MW orequivalent make as approved by the Deptt.) wiring system including 5 pin 6 amp flush type plug socket ND 6 Amps. F/T switch (Anchor penta/Gold medal/Kolor Kany Kom/Havells........ .........or equivalent make as approved by the Deptt.) and 6 Amp flush type switch (Anchor penta/Gold medal/Kolor Kany Kom/Havells or equivalent make as approved by the Deptt.) GI/MS switch board (ISI marked with phenolic laminated sheet cover) including earth continuity with 1.5 sqmm cable to third pin of the plug socket etc. as required complete, when placed elsewhere.a) Medium point up to 6.00 M length

a) Long point point up to 10.00 M length

Wiring for drawing sub main line with PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS 694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1.1 KV (Finolex/RR cable or equivalent make as approved by the Deptt.) PVC conduit (Berlia/ AKG/Precision/Presto Plast/Polycab/MW orequivalent make as approved by the Deptt.) including earth continuity in surface/recessed conduit wiring system with 20 mm dia 2mm thick/ heavy rigid PVC IS : 9537 Part-III rigid PVC wiring system. With 2x2.5 sq-mm+ earth continuity with 1x1.5sqmm in 20mm dia 2mm thick/heavy rigid PVc IS 9537 Part-III conduit.

With 2x6 sq-mm+ earth continuity with 1x4 sqmm in 25 mm dia 2mm thick/heavy rigid PVc IS 9537 Part-III conduit.

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof double door IP-43 surface mounting SPN MCB DB incorporated with bas bar, Neutral link, Earth bar and din rail etc. fitted on wallwith grouting nuts & bolts as required complete with making necessary connection as approved, specified and directed by the Deptt 8 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof double door IP-43 surface mounting SPN MCB DB incorporated with bas bar, Neutral link, Earth bar and din rail etc. fitted on wallwith grouting nuts & bolts as required complete with making necessary connection as approved, specified and directed by the Deptt (ABB, Schneider MG, Legrand, Hager, Crabtree xpro make 4 Way TPN (4+12) double door

Supplying witb fitting and fixing Four Pole 415V Front Handle operated on load change over switch (IP-20 protection) powder paintedsheet steel enclosure fitted on angle iron frame of the following capacity complete with making necessary connection as approved, specified and directed by the Deptt(C&S, Havells, Indo Asian, HPL, GECO make)

Supplying with fitting and fixing single pole 10 KA 240/415V 50Hz MCB of the following capacity with making necessary connection as approved, specified and directed by the Deptt C Series (Schneider MG, Legrand, Hager, Crabtree xpro make) 6-A

Supplying with fitting and fixing DP 10 KA 240/415V 50 Hz MCB of the following capacity with making necessary connection as approved, specified and directed by the Depttcapacity with making necessary connection as approved, specified and directed by the Deptt 6 to 32A SPDB

Supplying with fitting and fixing DP 10 KA 240/415V 50 Hz MCB of the following capacity with making necessary connection as approved, specified and directed by the Depttcapacity with making necessary connection as approved, specified and directed by the Deptt C Series (ABB,SchneiderMG, Legrand, Hager, Crabtree xpro make

Supplying including fitting and fixing of following star rated A.C. Ceiling fan complete with all accessories like down rod,canopy etc. of following sweeps with making necessary connection as approved, specified and directed by the Deptt [ without regulator] (ORIENT PSPO make/Usha make/CROMPTON make/Havells/ATC/V GAURD make) Energy efficient 5-star 1200 mm sweep ORIENT PSPO/Usha/CROMPTON/Havells/ATC or equivalent make

Supplying including fitting and fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved, specified and directed by the Deptt .(High speed 225 mm sweep (ORIENT make), Trans Air 225 mm sweep (Crompton make), Ventil Air DX 250 mm sweep Louver type (havells make)

Philips LED bulbs non-dimmable 7/9 W or equivalent as approved by the Deptt.

supply,installation & testing of G.I earth station with perforated 40mm dia and 4.50 metre long heady duty G.I pipe with necessary 40 mm dia. G.I fittings such as socket , tee, elbow, nipple and 50mmx300mmx6mm hinged cover G.i earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt. .

suppling & laying of 8 SWG G.I earth from earth electrode (below G.L) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt

External Electrification at AEE Office,Naokata Suppling &laying of 25x4 mm sizecopper strips drawn on surface from electrode to electrical switch gears machineries etc complete with suplly of brass nuts & bolts, screws etc including riverting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supply,fitting & fixing 20mmx5mm G.I strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of G.I nuts & bolts, screws etc including riverting, soldering and making connection as approved by the deptt. with earth electrode G.I strips and lightning arrestor etc. as specified and directed by the deptt.

Supplying including installation of connection cable, as approved by the Deptt. With 2x2.5 sqmm copper FR cable, testing and commissioning of the following street light on existing pole/structure including lamp,driver, ballast as required complete as directed and specified by the Deptt.Philip lighting luminaries 36W Green Line Model BRP409 LED CW 036 MR FG S1 PSU GR/BRP409 LED CW NR FG S1 PSU GR or equivalent as approved by the Deptt.

Suppling including fitting and fixing of hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300mm long pipe of thickness 3 with arrangement to fix on pole top with 3 nos. of bolts. Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ / PHILLIPS/ VALMOUNT/ PARUTHI ENGR/Nezone make) Stiffer plate from arm of the following tipes : single arm bracket 1000mm long for 3m to 10 metre. Poles.

Suppling with fitting and fixing DP 10 A 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB,Schneider MG, legrand, hage, Crabtree xpro make) 6 to 32A

Suppling including fitting and fixing bus bar chamber (HPL/GECO/or equivalent make) with 4 strips bus bar of length 350/450/600/900/ mm made of aluminium alloy or wrought aluminium suitable for 100 amp capacity complete with all accessories including connection etc. as required complete.

Water Supply and Sanitary Works for AEE Office and Irrigation Colony Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) A) Parryware make a) White (i) Universal Closet S Trap (Cat No.C0271) (Anglo Indian) (inclusive of seat cover)

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) A) Parryware make a) White (ii) Deluxe Single Flush (Cat. No. C8091/C8057)

Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately) Indian type W.C Orissa pattern of size 580 x 440 mm A) Parryware make a) White

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid A) Parryware make a) White (i) Duke 660 x 495 (Cat. No.C8416/27) (white/coloured)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (A) Parryware Make (i) Single Bowl with Veg Bowl & Drain Board (400 x 200) Flat Edge- Glossy (Cat.No.C8545)

Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc.complete at all levels including below G.L. as directed and specified. (A) Exposed on walls b) 40 mm dia (Medium)

d) 25 mm dia (Medium)

f) 15 mm dia (Medium)

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) Essco make (Delux/Sumthing spl./Tropical) (a) Bib cock short body

(b) Long body bib cock with wall flange

Supplying fitting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) (iii) 25mm dia

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. (a) Jaquar make (i) Continental towel ring square (Cat.No. ACN-1121)

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. (a) Jaquar make (i) Continental towel ring square (Cat.No. ACN-1121)

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) Sona brand a) Sink cock upper/ lower spout 15mm

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. Sona brand (b) Heavy type

Supplying and placing ferrocement septic tanks of rectangular shape in to pit with manhole cover with cleaning arrangement over single brick flat soling and 75mm 1:3:6 P.C.C. Baffle wall, inlet and outlet etc are provided at suitable points complete as directed. (i) 10 users

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes 1000 Lt capacity (a) Sintex make

Construction of overhead RCC water tank

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of DOLPHIN make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six months (A) With Zoloto fittings (III) 5000 liters capacity (a) 4 mm thick Vessel

Supplying,fitting fixing 1 HP Centrifugal Pump (Crompton/Bajaj Make)

Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department. ii) Bore hole of 100 mm diameter

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. G.I. pipe a) TATA / SAIL (Medium) socket should be welded to the pipes. iii) 80mm diameter

Supplying fitting and fixing GI filter 2.00 metre long

Supplying fitting and fixing check valve (non return valve) including thread to pipes. vi) 80mm diameter

Labour for sinking tube well with 40mm (internal) dia G.I. Pipes up to having strata, having potable water including fitting and fixing strainer hand pump and other accessories as directed complete as in any soil.

Flushing, clearing, washing and watering of the tube well

Construction of RCC Stagging for overhead Water Tank at AEE Office Earth work in excavation for foundation trenches of walls retaining walls footings of column, steps, septic tank etc including refilling (return filling) the quantity as necessary after completion of work watering and ramming etc and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.

Providing brick soling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and necessary dewatering, complete. (a) Brick on flat soling

Plain cement concrete works with coarse aggregate of size 13mm to 32mm in foundation bed for footing steps, walls brick works etc. as directed and specified including dewatering if necessary and curing complete (shuttering where necessary shall be measured and paid separately) (a) in prop 1:3:6

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete ( upto 1st floor level). a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: (a) Foundation footings bases of columns pile cap, raft and mass concrete works etc.

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: Sides of tie beams, plinth beams, grade beams etc. at orbelow plinth level (ii) Using 25mm thick plank

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (ii) Using 25mm thick plank

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: Column, pillars, posts & strut Sides and soffits of beams, beam haunching, cantiliver girders, bressumers, lintels and horinzontal ties (ii) Using 25 mm thick plank

Providing form work of ordinary planking so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removed of the same for in-situ reinforced concrete and plain concrete work in: Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (ii) Using 25mm thick plank

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) I) Using Mixer Machine (A) In substructure up to plinth level Foundation footing columns with base tie and plinth beam grade beam pile cap base slab retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (A) M15 grade Concrete

Providing and laying plain reinforce cement concrete works in prop1:1.5:3(1cement:1.5 coarse sand :3 graded stone chips, 20mm down) including dewatering if necessary and curing complete but excluding cost of form work and reinforcement for reinforced cement conrete work (form work and reinforcement will be measured and paid separately) (B) In super structure from plinth level up to 1st floor level. (ii) Columns, pillars posts struts suspended floor, roof landing shelf and support balcony lintel sill band beam girder bressumer cantilever staircase including preparing of top surfaces and furnishing and nosing (a) M15 grade concrete

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In proportion 1:4

15mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering upto 1st floor level including arises, internal rounded angles, not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

Colour washing with lime on wall surface (two coats) over and including a priming coat of white washing to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and other foreign matter.

25 mm thick cement concrete topping 1:2:4 (1cement : 2 coarse sand : 4 coarse aggregate of 12 mm nominal size) finished with a floating coat of neat cement finish to be laid in panels including curing complete as directed.

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (a) 15 mm thick

Furniture at AEE office,Naokata Steel half Secretariat table with 3 (three) equal size drawer top made of 18mm thick both side pre-laminated ISI/ISO certified particle board steal frame made of 0.91mm thick C.P. sheathed and 25 mm, 1.20 mm thick MS square pipe nicely finished with Duco/Enamel spray similar to Godrej model, size 1230mm X 615mm X 750mm

Steel full Secretariat table (U.D.A) with one side three equal size drawer and other cupboard. Top model 18mm thick both side predominated ISI/ISO certified recticule board steel frame of 0.80mm thick C.P. sheathed 1.20mm thick, 20mm MS square pipe nicely finished with Duco/Enamel spray similar to Godrej. size 1370mm X 760mm X 760mm

Premium Wood Steel Table with ERU made of steel frame 1.98 mm thick 33 mm MS square pipe & 0.91 mm CR steel finished with both side prelaminated ISi/ISO certified particle board one side three equal size one drawer & cupboard similar to Godrej Model WT-718.

Executive Revolving High Back Chair comfort & style(similar to Gdrej Model PCH-7001)

Medium Back Executive revolving chair

Table Glass( 8 mm thick)

Steel Almirah with 4 (four) shelve 5 compartments with three way inside locking system having a rigid unpick able 6 (six) lever lock with stanless steel key. Enamel spray painted ans nicely finished, made of CR sheet not less than 0.8mm thick without bars and dents an materials Item No. 1 containing to IS Specification Size 1980mm x 915mm x 457mm

Skeliton type steel Rack made of slotted angles with adjustable bit shelve including top and bottom made of 0.8mm CR sheet nicely finishedwith enamel spray paint with out any bars and dents size

All-in-One Heavey Duty Xerox cum printer cum scanner Machin of Reputed Make (Epson,Cannon/Eqvt Make)

139cm(55 inch) Ultra HD (4K) LED monitor,of Reputed Make,(Sony/LG/Equivalent Make)

Deraj Saikia

Natsakee Incorporation