Special Repair of Quarter No.DD-2 Type -V

Amount

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :

Of sectional area 40 square centimetres and above

Providing and fixing in wall lining marine plywood of approved brand like (Green Ply, Century ply) conirming to IS : 710 specification cluding priming coat on unexposed surface arrangement and screws etc. complete.

12 mm thick.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing 2nd hard wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface.

12 mm thick.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (One or more coat applied @ 0.90 ltr/10 sqm).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources).

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form work for :

Foundations, footings, bases for columns

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

With cement mortar 1:4 (1 cement : 4 fine sand)

Renewing glass panes, with wooden fillets wherever necessary:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe (19.1.1) 32 mm dia

Providing and fixing uplasticised PVC connection pipe with brass unions :

30 cm length (21.1.1) 15 mm nominal bore

Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door (23.1.1) 110X110X110 mm

Bend 87.5° (23.1.2) 110 mm bend

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Hard wood Cat - II (A)

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Superior Hardwood Cat-II A (25.1.1) 35 mm thick

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : with necessary stainless steel screws etc.

Superior hard Wood Cat-II(A)

Providing and fixing Health Faucet with 1 meter long easy flex tube in Chrome Finish & Wall Hook (ALD-CHR-565 Jaquar)

Providing and fixing soap dish holder. Cat No.CAN-1131N make or equivalent.

Providing and fixing Pillar Cock make of Jaquar CON - 011 KN or equivalent a). 15 mm nominal bore.

Providing and fixing angular Stop Cock with Make of Jaquar or equivalent.

Providing and fixing CP brass bib cock of approved quality : make of Jaquar CON-037KN or equivalent a) 15 mm nominal bore

Providing and fixing C.P. brass shower rose 105mm dia round shape with 15 or 20 mm inlet : with Rubit Cleaning System (Make in Jaquar OHS-1709)

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Thickness above 10 mm up to 25 mm

Mega Engineers and Builders

J K CONSTRUCTION

M/S RAJU CONSTRUCTION

K SRINIVAS RAO