CA NO. GE AF NO.1/GUR-33/2023-24 REPAIRS TO PLASTERING, FLOORING, ROLLING SHUTTER AND JOINERY INCLUDING CONNECTED BR WORKS IN MES INSTALLATIONS AT AF STN GURGAON UNDER GE (AF) GURGAON NO. 1.

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises completed all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete of any description and in any position complete all as specified and as directed by Engr-in-Charge.

M&L for 75mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor, path and hard standing complete all as specified and directed.

M&L for 75 mm thick plain cement concrete type B-2, 1:2:4 (40 mm graded aggregate) laid in path and hardstanding complete all as specified and directed by Engr-in-Charge.

M&L 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand completed all as specified and as directed.

M&L Machine cut kota stone flooring 20-25 mm thick over 15 mm thick CM 1:6 screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as directed by Engr-in-charge.

M&L for PCC 1:2:4 type B1 using (20mm graded stone aggregate) as in cills, copings, small plates including weathering slightly rounded or chamfered angles and throating including necessary form work complete all as directed by Engr-in-Charge.

M&L Chequered Cement concrete tiles 300x300x20mm thick, set jointed and pointed in neat cement slurry in floors with white cement and pigments in any colour over and including cement screed bed 15mm thick in cement mortar 1:4 all as specified and as directed

M&L Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surfaces of size exc 0.05 sqm and n.exc 0.18 sqm and 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for precast Kerb stone with plain fair faces 300x150x300 mm depth of PCC 1:1 ½ :3 of shape as approved incl all excavation, embedding in ground and removing surplus spoil upto 50 Mtr distance completed all as specified and as directed.

M&L for PCC 75 mm thick type C-2, 1:3:6 using (40 mm graded aggregate ) as in plinth protection path finished even and smooth without using extra cement complete all as specified and directed.

Cutting and grinding mirror polishing old kota stone flooring including applying cement slurry to fill the existing joints completed all as specified and as directed

Taking out the existing paver blocks of any size and set and jointed again in the same position after cleaning of grass and other vegetation etc all as directed and specified.

M&L for Preparation of old painted steel surfaces and applying two coat of synthetic enamel paint over 10 cm width or girth over one coat of red oxide primer complete all as specified and directed

M&L for Preparation of new or previosuly untreated steel/concrete surfaces and applying two coat of synthetic enamel paint over 10 cm width or girth over one coat of red oxide primer complete all as specified and directed

M&L for preparing of new plastered surface of walls, applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489 : 2004 Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied & .90 ltre/10 Sqm as directed by Engr-in-Charge. (Note- work will be strictly executed by mechanised means/tools as required for smart periodical services)

M&L for complete removal of existing treatment including preparing of old plastered surface of walls, applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489 : 2004 Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied & .90 ltre/10 Sqm as directed by Engr-in-Charge (Note- work will be strictly executed by mechanised means/tools as required for smart periodical services)

M&L for prepration of new plastered surfaces of walls by Vacuum based sanding machine complete all as specified, applying wall care putty upto 1mm thick as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured over a coat of approved primer by auto roller complete all as specified & directed

M&L for complete removal of existing treatment from old decorated plastered surfaces of walls by Vacuum based sanding machine complete all as specified, removal of nails etc & filling cracks/hole with putty, applying wall care putty upto 1mm thick as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured over a coat of approved primer by auto roller complete all as specified & directed

M&L for prepration of new plastered Surfaces of WALLS and applying two coat of colour wash, over one coat of white wash on plstered and other surface, preparatory to priming complete all as specified and as directed.

M&L for complete removal of existing treatment of plastered Surfaces of WALLS and applying two coat of colour wash, over one coat of white wash, complete all as specified and as directed.

M&L for preparation of new surfaces on ceilling, and applyig two coat of white wash over one coat of white wash completed all as specified and as directed

M&L for complete removal of existing treatment plaster surfaces on ceilling, and applying two coat of white wash completed all as specified and as directed

Taking down existing bitumen felt roof treatment including cement mortar bedding and cleaning the surface and removal outside the MOD land, complete all as specified and directed.

M&L for Cutting out cracks 'V' section on existing roofs or terrace cleaning out and filling solidly with a hot mixture bitumen and clean dry sand 1:1 by weight complete all as specified and directed by Engr-in-Charge.

M&L 25 mm thick PCC 1:2:4, type B-0 (using 12.5mm graded aggregate ) as in padding of floors/ roof surface finished even and smooth surface completed all as specified and as directed.

Material and labour, 10 mm thick cement plaster in CM (1:4) mixed with WPC as per manufacturer’s instructions @ 3% by weight of cement on concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L water proofing treatment on roof and vertical surface consisting as under:- (a) Applying evenly a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces (b) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg/Sqm on plaster surface all as specified. (c) A layer of 3mm thick APP polymeric membrane of weight not less than 3.60 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/ sqm), duly sealed at over laps & joints with end laps of the 10cm and side over laps of 7.5cm by flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.

Supply only water proofing liquid compoundcomplete all as specified and directed by Engr-in-Charge. :Make : DR. FIXIT PIDE PROOF LW, CICO, FOSROC.

M&L for applying one coat aluminium heat resistance paint on the roof as per manufacture instructions complete all as specified and directed by Engr-in-Charge. Make : PLASCON/PLASCON or equivalent.

Dismantling of brick work built in cement mortar including all quions, arches, pillars, etc.completed all as specified and as directed

M&L for Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 completed all as specified and as directed

All as item 34 hereinbefore but using old serviceable bricks retrieved from dismantling.

Taking down cement plaster, any description on brick walls or on concrete surfaces including racking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed.

M&L for rendering 15 mm thick on fare faces of brick work or concrete surfaces in cement mortar 1:4 finished fair and even smooth without using extra cement all as specified

M&L for rendering 15 mm thick on stone surfaces or surface other than fair face of brick work or on one side of lathing in cement mortar 1:6 finished even and smooth without using extra cement all as specified

M&L for rendering 10mm thick in cement motar 1:3 on ceiling like chhaja, roof projection facia etc on concrete surfaces, finished fair & even without using extra cement completed all as specified and as directed.

Dismantling mild steel work of any description not otherwise provided completed all as specified and as directed

M&L Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes Fe 410 W (Gde-E-250) quality-A with riveted bolt or welded etc as in duct cover & similar work completed all as specified and directed

M&L for rolled section as tubular sections as in vertical steel columns with flange plates, caps, bases, base plates, splices angle brackets, cleats, holding down bolts and nuts and other section complete of Fe 410 W E-250 grade including all welding etc, complete all as specified and directed

S&F for MS framed work such as grills, grating, etc, with ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars; barred iron door; ladders; framed baluster; walk ways; railing; framed work of water tank, for portions framed and hung as gates, including pintle hinges, stops hand made sliding bolts, etc and similar work conforming to Fe-290, Gde-E-165 all as specified and directed by Engr in charge.

S&F for MS angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement complete all as specified and directed.

S&F in repairs 0.8mm mild steel, plain black sheet hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed.

S&F in repair Galvanized 2 stand Steel Barbed wire 2.24mm dia barbed with dia barbs at 75 mm spacing and straining and fixing to any type of stsnderd rails, straining bolts,including securing or tying at crossings with and provisuion of galvanised mild steel pins, etc incl taking down of existing barbed wire as directed (each line wire to be measured) complete all as specified and directed by Engr-in- Charge

S&F in repair 950/610/450 mm dia concertina coil reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/ Clips for tying at crossing complete including taking down of existing concertina coil all as specified and directed

Dismantling of plain or corrugated steel sheeting / AC sheeting any gauge thickness including nanital or similar pattern roof coverings all as specified and directed

S&F 0.5 mm thick pre coated thick galvalume aluminium zink coated GI based corrugated /plain steel sheeting of any colour having tensile strength of 550 MPA as in roof covering /clading to wall fixed with self tapping screws, complete all as specified and directed

S&F 2 mm thick fibre glass reinforced translucent corrugated/ plain sheeting with two corrugations side lap fixed with L type or J-type or cranked hook botls and washer in roof, wall and similar work etc all as specified and directed.

M&L in repairs for Chain link MS galvanised fencing, any size or type including line wires, any mesh, standartds rails, straining bolts etc including provision of binding wire all as specified and directed

M&L in repairs welded wire mesh/expanded metal not exc 4kg per sqm, cut to length, bent to shape required and tying with and including annealed muild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed to wood or steel members complete all as specified and directed.

Taking down steel rolling shutter of size exc 3.0 sqm but n exc 12 sqm and refixing the same after greasing and overhauling after making system fully functional including to the entire satisfication of Engr-in-Charge. (Note : Material replaced shall measured and paid seperately as 'supply only ' rate under respective item of Schedule.)

Supply only MS pipe medium grade of dia upto 40 mm including cutting and fixing, drilling, welding for rolling shutter complete all as specified and directed.

Supply only spring of high carbon spring 30mm dia drilling, welding for rolling shutter complete all as specified and directed.

Supply only mild steel rolling shutter strips made out of 1.25mm MS sheet including and reavting including one coat of primer and two coat of synthetic enamel paint all as directed Engr-in-Charge.

Supply only safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S &F in repair Mild Steel 1.25 mm rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated,complete: push pull or manual type complete all as specified and directed.

Dismantling of cast iron , concrete, asbestos, PVC pipes of any dia and discription from trenches or with walls etc complete all as specified.

S & F PVC pipes single socketed in any length with rubber ring joints fixed to wall ( 110mm bore) including flat iron clamp for proper fixing complete all as specified

S & F in repairs PVC bends 110mm dia complete all as specified

S & F PVC pipes single socketed in any length with rubber ring joints fixed to wall ( 75mm bore) including flat iron clamp for proper fixing complete all as specified by Engineer-in -Charge.

S & F in repairs PVC bends 75mm dia complete all as specified and directed.

S&F in repair, 500 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered, ISI marked, hoisted and fixed in position including tank nipples of required size and 20 mm bore dia pipe ball brass valve high pressure with plolythelene float and flynut complete all as specified in SSR Part I complete all as specified and as directed.

S&F in repair, 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered, ISI marked, hoisted and fixed in position including tank nipples of required size and 20 mm bore dia of pipe ball brass valve high pressure with plolythelene float and flynut complete all as specified in SSR Part I complete all as specified and as directed.

S&F in repairs vitreous China squatting pan 'orrisa' pattern white colour of size 580x440mm with integral foot rests including provision of cement concrete including P traps complete all as specified and as directed.

S&F in repair for vitreous china wash basin white flat backsize 550x400 including cutting for and pinning in ends of brackets including fixing of 32 mm low dencity polylethyne pipes (LDPE) of pressure rating 6kg/cm2,cupling ,PVC connection with 15 mm dia PTMT cheknuts ,brackets all complete as directed

S & F in repairs, 20 mm bore GI tubes, `medium grade', including all fiiting , fixed to wall / in floors completed all as specified and as directed

All as per item No 68 here-in-before but 15 mm bore.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel/aluminium frame glazed with putty or fixed with wooden /aluminium beads etc.completed all as specified and as directed

S&F 4 mm thick sheet glass,ordinary quality,in squares n exc 0.5 sq m each pane fixed to aluminium frame with rubber gasket or fixed with glass putty as required etc completed all as specified and as directed

S&F Single side writing informatory stainless steel reflecting Sign Boards size 4'x3' having with Aluminium sheet base of 2mm thickness having retro reflective tape base and front colour and matter of sign board will be furnished by Engr-in-Charge.The frame of Sign board shall be 2'' outer dia Square stainless steel pipe and having two legs of stainless steel Square pipe 9' long Each of 2'' outer dia square pipe the board shall be grouted in PCC work of size 350x350x450mm including taking down of existing complete all as specified and as directed.

Taking down Chowkhats or frames n exc 1.5 sqm each without taking of shutter from the frame all as specifed and directed

Taking down shutter of any discription exc 1 Sqm n exc 2 Sqm each complete all as specified and directed

Taking down shutter of any discription exc 2 Sqm each complete all as specified and directed

S&F factory made 30mm thick solid core Flush door shutter with block board with BWP plywood on both side all as specified directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification and as directed.

M&L Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and wood grain printed PVC Sheet used 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beaading of 10mm x 10mm used instead of exposed portion of PVC sheet beading for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; supplying & fixing in the frame at site as per specification & as directed.

M & L for preparation of new/old wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink wood primer all as specified and directed

S&F butt hinges medium weight MS cold rolled 100mm long complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolt to extruded section and fixed complete all as specified and directed.

S&F 150 mm aluminium handle, cast type anodised complete all as specified and directed.

S&F 250 mm long aluminum alloy, anodised, sliding door bolt long whith hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixidng bolts and siliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L Gunitting work for RCC work as in columns, beam, slab, perapet, chajjas etc by removing all loose concrete on the reinforcement, cleaning the surfaces with wire brushes and reinforcement with sand papers than applying apoxy paint to rusted reinforcement and S&F welded wire mesh fabric size not less than 95x95x3 mm on the prepare surfaces and finally applying guniniting 30 to 40 mm thick (average thickness )with presure gun using 1 part of cement and 3 part of coarse cement incl necessary form work where ever required all gunnited surface shall be brought in complete geometric figure even in the guniting opration only complete all as specified and directed. Note:- Where new or additional reinforcement is required the same shall be paid for separetaly of this schedule as above.

M&L for 6 to 8 mm dia TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Removing excavated material exc 1.5 Km and not exc 5 Km and depositing where directed at a level not exc 1.5 m above starting point complete all as specified and as directed.

Note:- The amount of Rs 1,11,420/- against Schedule of Credit on Page No 150 shall be deducted from the total amount quoted against Sch 'A' while deriving the Contract Sum for Acceptance

M/S SURINDERAS CONSTRUCTION CO.

J.P. Enterprises

M/S ujjwal associates

PAWAN KUMAR

M/S Parshant Associates

Phogat Builders