Construction of Outdoor Stadium at Rajmahal in Sahebganj District

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Filling in foundation trenches and plenth in layers not exceeding 150 mm thick well watered, rammed, fully compacted and fine dresssd with earth obdiened after cutting within a lead of 50 m and lift of 1.5 M all complete as per building specification and direction of E.I (Mode of measurement compacted volume.)

Providing coarse clean sand in filling in foundation trenches or plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts includng cost of all materials, Labour, rotalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume).

Providing designation 75B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening maerials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125mm thick reinforced designation 75A brick work in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement0 all complete as per building specification and direction of E/I.

Supplying and laying (properly as per design and drawing) Dressed random rubble stone masonry in C.M(1:4)good quality

Providing designation 100 A brick work with fly ash lime brick (FLAG)Confirming IS 12894-1990 (9"X4.5X3")in C.M (1:6)in superstructure with approve quality of clean coarse sand of F.M 2 to 2.5 including providing 10mm thick morter joints , cost of screening materials , raking out joints to 15mm depth , curing , taxes and royalty all complete as per building specification and direction of E/I

Providing P.C.C.M 150 in nominal mix of (1:2:4) in foundation with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, mixing cement concrete in mixer and placing in position vibrating, stricking, curing, taxes and royality all complete, as per building specification and direction of Engneer -in - charge E.I

Providing and Laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: (1:11.5:3): 3 graded stone aggregate 20mm nominal size.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations,footings, bases of columns, etc for mass concrete.

Providing and Laying in position specified grade of reinforced cement concrete, excluding the cost of centering and shuttering - All work up to plinth level: (1:11.5:3): 3 graded stone aggregate 20mm nominal size.

Providing and Laying in position specified grade of reinforced cement concrete, excluding the cost of centering and shuttering - All work up to plinth level: (1:11.5:3): 3 graded stone aggregate 20mm nominal size.

Centering and shuttering including strutting, propping etc. and removal of form for - Walls (any thickness) including attached pilasters, butteresses, plith abd string courses etc.

Reinforced cement concrete works in beams, suspended floors, roofs having slope up to 15" landings, balconies, shelves, chajjas, lintel, bands, plain window sills, staircase and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcemewnt: 1:1.5:3: 3 graded stone aggregate 20mm nominal size.

Centering and shuttering including strutting, propping etc. and removal of form for - Lintels, beams, plith beams, girders, bressumers and cantilevers.

Reinforced cement concrete works in beams, suspended floors, roofs having slope up to 15" landings, balconies, shelves, chajjas, lintel, bands, plain window sills, staircase and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcemewnt: 1:1.5:3: 3 graded stone aggregate 20mm nominal size.

Centering and shuttering including strutting, propping etc. and removal of form for - Suspended floors, roofs, landings, balconies and acess platform.

Reinforced cement concrete works in beams, suspended floors, roofs having slope up to 15" landings, balconies, shelves, chajjas, lintel, bands, plain window sills, staircase and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcemewnt: 1:1.5:3: 3 graded stone aggregate 20mm nominal size.

Centering and shuttering including strutting, propping etc. and removal of form for - Lintels, beams, plith beams, girders, bressumers and cantilevers.

Reinforced cement concrete works in walls, includiing attached pilasters, buttress, pliinth and string courses, fillets, columns, pillars, piers, abutments, post and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcemewnt: 1:1.5:3: 3 graded stone aggregate 20mm nominal size.

Centering and shuttering including strutting, propping etc. and removal of form for - Columns, pillars, piers, abutments, posts and struts.

Reinforced cement concrete works in beams, suspended floors, roofs having slope up to 15" landings, balconies, shelves, chajjas, lintel, bands, plain window sills, staircase and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcemewnt: 1:1.5:3: 3 graded stone aggregate 20mm nominal size.

Reinforced cement concrete works in beams, suspended floors, roofs having slope up to 15" landings, balconies, shelves, chajjas, lintel, bands, plain window sills, staircase and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcemewnt: 1:1.5:3: 3 graded stone aggregate 20mm nominal size.

Centering and shuttering including strutting, propping etc. and removal of form for - Stairs, (excluding landings) except spiral staircase.

Reinforced cement concrete works in beams, suspended floors, roofs having slope up to 15" landings, balconies, shelves, chajjas, lintel, bands, plain window sills, staircase and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcemewnt: 1:1.5:3: 3 graded stone aggregate 20mm nominal size.

S/F 35mm thick solid core type non-decorative single leaf flush door and windows with black board core banded with high quality phenol formaldehydes synthetic resin both side commercial veneered of standard make with oxidized iron fittings such as hinges, sliding door bolts tower bolts, handles or rings hooks and eyes, cleats sand block as per schedule taxes and royalty all complete as per building and direction of E/I.

Providing Toe steel reinforcement of 8mm dia to 32mm dia rods as approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL & TATA STeel) 8 mm to 32 mm dia (TMT coil Fe 500) (Only Valid for SAIL & TATA Steel)

S/F M.S. grill made of 20 x 6mm M.S. flat as per approved design and drawing, properly fabricated with joints continous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction ofE/I. (Where materials is not supplied by the deptt.) ' @22 kg per Sq.m

Providing and fixing fan hooks of 16mm dia M.S. bar & 1 meter long, bent torequired size and shape, placed in position and fixed in the R.C.C.slab/beam at the time ofcasting all complete as per building specification and direction of E/I.

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

labour for fitting and fixing barbed wire fencing in four rows horizontal upto a height of 1.85M. And two ndiagonals including fixing of post in cement concrete at 2.5 M. centres including cost of staples (but excluding the cost of cement concreteangle iron post ,its cutting and making holes ,nuts andbolts )all complete as per building specification and direction of E/I

drilling 6mm dia holes . M.Sangle iron for fixing of staples etc . As per building specification snd direction of El

Labour for cutting of m.s angle iron to required length ,one end splitted of as finished in a length of 150mm cokplete as per building direction of E/I

supplying fitting and fixing srining b oit with nut size 20cmx 10mm dia to tigthin the berbed wire corner post complete as per building specification and direction of e/I

Supplying fitting and fixing M.S grill gate with M.S grill made of 20 x 6 mm M.S flats or 16 mm M.S square bras fitted on 25x25x6 mm M.S angle frame -- do -- (where materials is not supplied by the deptt.)

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering texes royalty all complete as per building specification and direction of E/I.

Providing and laying20mm thick white makarana marble stone slab flooring of approved texture (2) 300 x 600 mm

Providing and laying 20 mm thick white makarana marble stone slab . Thick cement plaster (1:3) base with sand of F.M. 1.5 rubbed and polishedto granolithic finish, With 100% white Cement:-

Providing and laying 6 mm precast SEMI GLAZED CERAMIC TILES of approved quality in DADO over 12mm cement mortar (1:3) and jointed with white cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction of E/I with Commercial grade white 15cmx15cm tiles.

Providing 12mm thick cement plaster (1:4) in WALL with materials ---do --- complete job as per specification and direction of E/I.

Providing 1.5 mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E.I

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 19mm . Thick WATER PROOF cement plaster (1:3) in TOP ROOF with clean coarse sand of F.M. 1.5

Providing two coats of Plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. (OUTSIDE & INSIDE WALL)

Providing two coats of snowcem of approved shade and make over a coat of cement primer over new surface including prepairing the plastered surface by rubbing smooth with sand paper scaffolding curing,taxes all complete as per building specification and direction of E.I

supply m.s angle 50x50x6 4.5 kg/m

supply or barbed wire 0.50 kg/m

Applying priming coat with ready mixed paint over a coat of primer of approved shade and mike over new wooden surface including preparing the surface after cleaning, removing dirt-do

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales, smokes, grease and sand preparing, including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specificatio).

Providing two coats of painting with ready mixed paint of approved shade and make over steel surface ….

Providing P.C.C. M-150 with nominal mix (1.2.4) in foundation & plinth with approved Quality of stone metal grade-III (50 mm to 25 mm size) clean coarse and of

Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer withpower roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginalbanks, and guide banks etc., lead up to 50 m and lift up to 1.5 m :

Providing and fixing pressed steel door frames confirmig to IS: 4351 manufactured form commercial mild steel sheet of 1.25 mm thickness including hinges jomb, lock jamb, bead and if required angle threshold of mild

P.V.C. Pipe for whole one each 2.0 m distance IN stone masonary

Providing C l+ wo Cl Manhole=2' dia 600x450mm-39.00kg

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and Is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top.... Anodised aluminium

Providing and fixing glazaing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket ….. With float glass panes of 4.0mm thickness

Providing weep hole with dry gradeed stone filter of 20 mm to 40mm size in abutment and wing wall as per specification and direction of E/I

Carriage of materials

Bricks Lead = 1 k+7 P(8km)

Flyash =1 k+7 P

Sand lead = 10 km

Stone chips lead = 22 km

bolder-22 km

Rough dressing the trenched ground including breaking clods

Fine dressing the trenched ground including breaking clods

Renovating lawns including weeding. Cheeling the grass forking the ground top dressing with sludge or manure mixlng the same with forked soil watering and maining the lawn free from weeds and fit for mowing and disposal of rubbish

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to250.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 50 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Providing and fixing WATER CLOSET squatting pan Indian type W C pan ) with 125 x 110 dia uPVC, p-trap 10 litre low level white PVC flushing cisten with manually controlled device (handle lever ) flushing cistern with manually controled device (handle lever) conforming to IS:7231, Parryware/ Hindware / Seabird / Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. White Vitrebus china Orissa patterns WC pan of size 580 mm x 440 mm with integral type foot rest.

Providing and fixing WASH BASIN with C I / M S brackets 15 mm C P brass piller taps Kingston/ Gem / Techno / Parko 32mm C P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require.

WHITE VITREOUS CHINA

Flat back wash basin size 550x400mm with single 15mm CP brass pillar tap.

Supplying fitting and fixing flat back or angular, lipped front vitreous white glazed earthan ware URINAL of Hindustan “Parry” or any other approved ISS make with 5 liters capacity CI automatic fulsing cistern of reliance for any other ISS approved make with all fittings with CI or RS brackets standard size GI flush pipe with fitting clamps, 15mm CI body brass spindle stop cock of approved quatity weight not less than 400 gms , 15mm PVC / Alkthene pipe 450mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a primer coat of red oxide cutting wall and floor making good the same etc. all complete as per specification and direction of E/I .

Providing and fixing PVC Cowel fitting of approved make confirming to all complete job. 110 dia Upvc

Supplying materials and labours for constructing INSPECTION CHAMBER of destination class 75B bricks size 750mm deep, 600x600mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with complete job.

Providing and fixing BEND of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. (TEE) 100mm Upvc

WATER SUPPLY

Providing and fixing CP BRASS BIB COCK of approved quality conforming to IS:8931. 15mm nominal bore

Providing and fixing CP BRASS ANGLE VALVE for basin mixer and gyer points of approved quality conforming to IS:8931 15mm nominal bore.

Providing and fixing uplasticied PVC CONNECTION PIPE with brass unions 30cm lenth

Providing and fixing C P brass STOP COCK (concealed) of standard design and of approved make conforming to IS:8931

32mm nominal bore.

Providing and fixing PTMT TOWEL RAIL complete with brackets fixed to wooded cleats with CP brass screws with concealed fitting arrangement of approved quality colour and make ( Prayag or equivalent )

Providing and fixing GUN METAL GATE VALVE with CI wheel of approved quality (screwed end )

25mm nominal bore

40mm nominal bore

MISCELLANEOUS ITEMS

Providing and placing on terrace (at all floo levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and marking necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank.

Provinding and fixing on wall face unplasticiesed Rigid PVC RAIN WATER PIPES conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion. Single socketed pipes 110mm diameter.

Providing and fixing on wall face unplasticised PVC moulded fittings/ accessories for unplasticsed Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion. 110mm BEND

Providing and fixing on wall face unplasticsed PVC moulded fiottings / accessories for unplasticsed RINGING PVC RAIN WATER PIPES CONFORMING to IS:13592 Type A Including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion. 110mm Shoe

Providing and fixing unplasticsed PVC PIPE CLIPS of approved design to unplasticsed =\-PVC rain water pipes by means of 50 x 50 x 50mm hard wood plugs, screwed with Ms screws of required length including brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand ) with a floting coat of neat cement inside the drain, its top and exposed side including disposal of surplus earth complete as per standard design

Supplying materials labour for construction of BRICK MASONRY DRAIN over 80mm thick PCC (1:3:6) over brick flat soling 150mm wide and 250mm av. Depth with brick work in cement mortar (1:6) in apron on both sides and 12mm thick cement plaster (1:3) with neat cement punning on exposed surface all complete as per specification and direction of E/I. Point Wiring in PVC Conduit, with Modular type Switch:-

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

Group B

Supply and Fixing Light Plug Point with Modular Type Accessories:-

Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

Supply and Fixing Light Plug Point with Modular Type Accessories:-

Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

Power Plug Wiring in PVC conduit (2x4 sq. mm):-

Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sq mm earth wire(For 5/6A Plug Points )

2x2.5 Sqmm + 1x2.5 sq mm earth wire For (Switch board and Bay Light)

4x10 Sqmm + 2x10 sqmm earth wire (For Normal TPN DB)

Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (Without MCB/RCCB/ISOLATOR).

6 Ways (6+12 ways) double door

S/F 'C' series SP MCB:-

Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32A Single Pole

50/63A TPN MCB

Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Modular type electronic fan regulator:- Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

ITC Exhaust Fan/Wall Fan upto 450 mm sweep :- Installation of exhaust fan / Wall Fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F Modular Boxes, base & cover plate (Used for TV and Tele.) :- Supplying and fixing following size / modules GI box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 module (78 mm x 78 mm x 45 mm)

S/F PVC Conduit ( for T.V. and Telephone):- Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for Tele, T.V.

Telephone Wiring in Existing Conduit:-

Supplying and drawing following pair,0.5 sq. mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface/recessed PVC conduit as required.(2 pair)

TV Wiring in Existing Conduit:-

TV Cable in Existing Conduit: Supplying and drawing co-axial TV cable RG-6 grade copper conductor, PE insulated, with PVC sheath in the existing surface/recessed PVC conduit as required,

S/F Modular type Switch / Socket:-

Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required.

5/6 amps,one way switch (for Existing Switch Board)

5/6 amps, 3 pin socket outlet (for Existing Switch Board)

Telephone socket outlet

TV antenna socket outlet

COPPER EARTH PLATE ELECTRODE:-

Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required.

P/F 25 x 5mm copper earth strip in pipe :-

Providing and fixing 25mmx5mm cpper earth strip in 40mm & 4.5Mtr long G.I.pipe for earth electrode etc. as required.

Salt & Cock for plate earth elecrode :-

Providing and fixing salt and cock for G.I. & copper plate earth elecrode etc. as required.

Providinging and fixing of following rating and breaking capacity four poles MCCB in the existing Verticle DB complete with connections etc. as required .

100 Amp. 16 KA MCCB 415 Volt

SUPPLY ITEMS

Supply of surface/ pendent mounted with chain Batten type LED 4ft Tube light fitting with Housing & cover made up of CRCA sheet steel. Cover is fixed to the housing by means of 2 Nos. bolt with engineering plastic head along with 1 nos LED tube of 20/22W Each of luminous efficacy of efficacy >110 Lm/W. Make :- .Wipro- 8.LL13-180-65SE- (1X20W-LED)/ Philips- TCW450P1XTLED 19W-P3397+Master LED-TL-20W-1200mm / Havells-BATTEN- 1X22/20W- (Double Side) TITANIA-LED-TUBE LIGHT-20W-LHFYBYPNIA-1W-022-1200mm/ Equivallent in Cropmton.

Supply of surface mounted round circular ceiling light fixture LED 1x18W-P LED control gear box,electronic blast etc. complete in all respect as required and as per the standard cataloge item.Make:-Philips ,Bajaj ,Wipro,opulus.

Supply and fitting of Mirror Light fixture LED 1x10W/12W Make:-Philips ,Bajaj ,Wipro,opulus.

15W LED type bulb :- Supply and fixing of 15 led bulb in existin Holder Fitting (Make:- Philips / Havells/ Wipro/Baja/opulus.

Bulk Head :- Supply and fixing of Bulk Head With 9 W led bulb Fitting (Make:- Philips / Havells/ Wipro/Baja/opulus).

Supplying and fixing indoor recess mounting 36 watt LED flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. directly on false ceiling including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable and earthing the body etc. as required. (Make:- Philips / Havells/ Wipro/Baja/opulus).

Supplying and fixing recess mounting LED 18 watt vertical downlighter complete with all accessories and replaceable electronic driver etc. directly on false ceiling including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable and earthing the body etc. as required. (Make:- Philips / Havells/ Wipro/Baja/opulus).

Supply of 1200mm sweep ceiling fans complete without regulator, double ball bearing, motor, blades, down rod, canopies, capacitor, suitable for operation on 230 volts, 50 Hz., 1 phase, AC supply connection with 1.5 sq.mm PVC Copper wire complete as required (BEE Five star rated minimum air delivery of 218 CFM/M , 2 years warranty.Fan shall be approved by engineer incharge/consultant) (COLOUR OF CEILING FANS- WHITE.- ISI.) Make- Havells / Bajaj / USHA

Supply of AC 230/250 Volts, 50Hz,300mm sweep Exhaust Fans including providing nuts- bolts, mounting frame and other required accessories etc. (For toilets and kitchen) Make:- Bajaj / Havell/USHA .

Supply and erection of 7 meter height Hot-dip galvanized octagonal street pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base of size 220 x 220 x 12 mm ,small door opening for junction box mounting and suitable size foundation bolt with tamplate and all complete as required. Make:- Volmount/ bajaj/Transrail.

Double arm, 1500 mm

LED STREET LIGHT (90/100W)Make:- Philips/ Wipro/Bajaj.

LED FLOOD LIGHT(150/160)Make:- Philips/ Wipro/Bajaj.

Heavy duty,armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts.

3.5c x 120 sq mm

3.5c x 35 sq mm

4c x 16 sq mm

4c x 10 sq mm

2c x 6 sq mm

MV Cable Laying up to 25 sq. mm. in ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm. direct in ground including excavation, sand cushioning, protective covering by 2nd class bricks and refilling the trench etc as required.

MV Cable Laying up to 120 sq. mm. in ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding25 sq.mm. but not exceeding 120 sq.mm. direct in ground including excavation, sand cushioning, protective covering by 2nd class bricks and refilling the trench etc as required.

Erection of metalic street light Standard upto 6.5 m in C.C

COPPER EARTH PLATE ELECTRODE:-

S/L 8 SWG copper wire in ground (for main panel and AC panel) :-

S/L 8 SWG G.I. wire in ground :- Supplying and laying 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

ITC ceiling fan - Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (up to 30 cm) with 1.5 sq.mm. FR PVC insulated, copper conductor, single core cable etc. as required.

EXTERNAL LIGHTING PANEL

Supply, assembly, erection, connecting, testing & commissioning of LT weather proof dust and vermin proof, outdoor feeder pillar,IP-55, fabricated out of suitable sized angle iron and flats and covered with 3mm thick CRCA sheet steel including canopy, duly stove enamel painted, both sides (front and rear) openable with locking arrangement, rubber gasket cable glands, etc. Bakelite phase separators and bus bar supports including RCC 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) foundation, 450 mm deep and 150 mm above the ground. The feeder pillars shall be complete with 3 phase and neutral bus bars of capacities as described below and moulded case circuit breakers (MCCBs) with adjustable overload relay, copper FRLS control wiring with 1.5sq.mm, complete in all respects as per specifications as required.

INCOMING:-

160A 4P MCCB (35kA) with thermal magnetic release & rotary handle - 2no.

3 Phase and neutral (100%N) aluminium bus bars of 200 amps. Capacity.

160A 4P Change Over (35kA) with thermal magnetic release & rotary handle - 1no.

OUTGOING:-

63 A 4P MCCB (25kA) with thermal magnetic release & rotary handle - 2no.

125 A 4P MCCB (25kA) with thermal magnetic release & rotary handle - 2no.

40A 4P MCB (10kA) - 4 nos.

63A 4P MCB (10kA) -6 nos.

63A DP MCB (10kA) - 5 nos.

16 AMP. MCB with 16A SWITCH & SOCKET - 2 no. with in the feeder pillar.

Digital type Ammetesr (0-250A)- 4 M.

Digital type voltmeter (0-500V) - 4 M .

LED indicatore (RYB) of 220V. (3 Nos.)= 1 Set. With 2A SP MCB protection for each indicator.r.

CT 100/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set.

External Lighting Feeder Pillar as above

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes ,royalty etc all complete job as per direction of E/I.

COST OF FIRE EXTINGUISHER 4.5 KG - 16 Nos

Add 12% GST

Add 1% Labour cess 1%

RABBANI CONSTURCTION PRIVATE LIMITED

GANESH PRASAD TIWARY

Maa Tara Infrastructure and Builders Pvt Ltd

SRI NIRMALA EARTH MINERALS PVT LTD