REPAIRS/MAINT OF CERTAIN LT PANELS, ACBs AND AT RECEIVING SUBSTATION IN WEST WING TECH AREA AT AF STATION GWALIOR

Amount

Supplying ,Laying, jointing and testing XLPE insulated, armoured, heavy duty, aluminum conductor cable 1100 volts grade ,laid in trenches/ducts, floors, fixed to walls etc. complete all as specified and directed for the following sizes. (a) 16 Sqmm, 4 core

(b) 25 Sqmm, 4 core

(c) 35 Sqmm 3 ½ core

(d) 50 Sqmm 3 ½ core

(e) 70 Sqmm 3 ½ core

(f) 185 Sqmm 3 ½ core

(g) 240 Sqmm 3 ½ core Note for item no 1.00 to 1.06 : The cost of taking down of LT UG cable is deemed to be included in the quoted rate

Excavation in trenches n exc 1.5 mtr wide and n exc 1.5 mtr depth for foundation and laying of cable and getting out in any type soil etc complete all as specified and directed.

Returning, filling in, including spreading, levelling watering and well ramming in layers n.exc 25cm in soft/loose soil etc complete as specified and directed.

Removing of surplus excavated soil not exceeding 50 M distance and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

S&F in repair HDPE DWC flexible pipe of Size 50mm external & 38 mm internal dia (ISI marked) including required clamps/couplers to be fix at 1.5 mtr interval on wall to fix the pipe properly and smooth suitable for insulation & protection of GI /copper /aluminium strip of any size complete all as specified and directed.

All as per item No 5 here-in-before but DWC flexible pipe of Size 63 mm external & 50 mm internal diameter.

All as per item No 5 here-in-before but DWC flexible pipe of Size 77mm external & 63 mm internal diameter.

All as per item No 5 here-in-before but DWC flexible pipe of Size 110mm external & 95 mm internal diameter.

M&L in repair Cable jointing kit for 1.1 KV cable for straight-through heat shrink type joint complete with jointing material and accessories suitable for 4 core XLPE armoured aluminium conductor cable of size 16 sqmm complete all as specified and directed.

M&L in repair Cable jointing kit for 1.1 KV cable for straight-through heat shrink type joint complete with jointing material and accessories suitable for 3.5/4 core XLPE armoured aluminium conductor cable of size 25 sqmm to 50 sqmm complete all as specified and directed.

M&L in repair Cable jointing kit for 1.1 KV cable for straight-through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70 sqmm to 120 sqmm complete all as specified and directed.

M&L in repair Cable jointing kit for 1.1 KV cable for straight-through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 150 sqmm to 185 sqmm complete all as specified and directed.

M&Lin repair Cable jointing kit for 1.1 KV cable for straight-through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 240 sqmm complete all as specified and directed.

M&L for Horizontal directional drilling (HDD) Boring of holes under road, pavement, hard standing, Runway/ PTT by trenchless technology using manual technique and necessary machine including privison of HDPE pipe of sie not less than 100 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed.

M&L for carrying out quarterly energy audit which includes detailed audit report as per the format given by the Engineer in charge with qualified technician as described below for complete LT distribution system from Transformer LT panel to Distribution board inside the building complete all as specified and as directed for the following location. The energy audit shall comprise of the following once in 03 months. (i) Recording of insulation resistance values and EN voltage values of all the connected cables from the main LT panel at the substation to distribution boards with a calibrated digital or analog insulation resistance meter. (ii) Recording of Earthing values in the specified format with a calibrated earth resistance meter digital or analog. (iii) Tighten the loose contacts of all ACBs/MCCBs/MCBs inside the panel and Distribution boards and record voltage and current values with calibrated testers. (iv) Complete report as per the format provided for each location.

a) 310 TRU, LT panels inside the substation, LT Panels outside the substation, Distribution Boards inside the building.

b) Complete IPSS LT, ACB's, panels inside the substation, LT Panels outside the Sub Station, Distribution Boards, Voltage Stabilizer, inside building total 07 Locations.

c) HQ Building, LT panels with ACB inside the substation, LT Panels with ACB outside the substation, Distribution Boards inside the building. Total No of LT Panels:- 08 Nos Total No of Distribution Boards - 40 Nos

d) Base ops, LT panels inside the substation, LT Panels outside the substation and building, Distribution Boards inside the building.of 25 MMPU. Total No of LT Panels:- 04 Nos Total No of Distribution Boards - 10 Nos

e) New ATC building LT panels near the building, and Distribution Boards inside the building. Total No of LT/AMF Panels:- 08 Nos Total No of Distribution Boards - 25 Nos

f) 01 Sqn Complete Hangar, Sub Station both LT and HT panels outside Squadron, LT panels near the DBs, and Distribution Boards Total No of LT/AMF Panels:- 08 Nos Total No of Distribution Boards - 45 Nos

f) 07 Sqn Complete Hangar, Sub Station, both LT and HT panels outside Squadron, LT panels near the DB's, and Distribution Boards Total No of LT/AMF Panels:- 08 Nos Total No of Distribution Boards - 45 Nos

Labour only for fault finding at any location round the clock inside technical area with locating the fault inside the cable with a cable fault locator and rectifying the fault, testing and commissioning after completion of the job. Note:- 1. Necessary labour, T&P required for completion of the job is deemed to be included in the quoted rate. 2. Necessary Cable jointing kit, excavation, return refilling only shall be paid seperately under relevant items. 3. Contractor has to mobilize necessary labour, T&P, material for fixing and rectifying the fault within 12 hours of receiving the complaint which is raised by Engr-in-charge/JE (E/M) either in writing or verabal. If the contractor doest not respond to the various calls, a penalty @ 500.00 for two hours after 12 hours shall be recovered.

M&L in repair bus bar box made out of 2mm thick MS sheet, 3 Phase, 4 wire, 415 volts AC supply outdoor cubical type, dist and vermin proof, floor block mounting type suitable for outdoor applications of size 600mm x 600mm x 450mm, using 40mm x 40mm x5mm angle iron frame with shutter and locking arrangement painted with two coats of synthetic enamel paint of approved colour over a coat of red oxide primer (internally and externally) for box, height above ground 600mm and graouted 300mm below ground, legs of frame shall be grouted in PCC 1:2:4 (size 300 x 300 x 300mm block) and complete includig 40mm x 10mm 04 nos 500 mm long aluminium busbar fixed on insulators with proper colour coding including making connecteions with cable of size 300 sqmm with necessary lugs and chromium plated glands complete all as specified and directed.

Cutting & removing of grass/shrubs/plants/bushes/Trimming of tree stems, etc, around the pole / LT panels / earthing pits/ Sub Station Building or any other location, complete all as specified and directed. Note:- The Contractor has to deploy the labour with the necessary tools as and when required.

S&F in repair danger notice plate of size 20x 15 cm,1.6 mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size for LT complete all as specified & directed.

All as per item No 19 here-in-before but for HT 25x20cm size

Supply, erecting and fixing in true vertical position, steel tubular swaged pole (410 SP – 31), 09 mtr long, complete with cast iron base plate, pole cap / finial taper plug, bolts, nuts and washers, welded reduced section and longitudinal weld throughout entire length and 2 coats of black bituminous paint externally upto planting depth and remaining exterior portion of pole shall be provided with one coat of red oxide primer and two coats of aluminium paint and numbering of the poles shall be done with synthetic enameled painted letter of shape & size including taking of old one complete all as specified and directed. Note:- 1. Necessary excavation, PCC for foundation and coping will be measured and paid seperately.

M&L for PCC type C-1 (1:3:6) (using 40mm graded stone aggregate) for foundation of poles struts & stay assembly etc complete all as specified and as directed.

M&L for PCC (1:3:6) type C-1 in coping of poles etc (using 20mm graded coarse aggregate) including fair finishing the exposed surface even and smooth without using extra cement and necessary form work for coping of poles all as specified and directed for the following

S&Fin repair GI pipe light grade bracket 40mm dia, 1.5m long bent to shape as required for fixing of street lights on poles/walls including nuts, bolts, washers, Clamps (02 sets) of suitable size complete all as specified and directed.

Supply and fix in repair Surge protection device Surge voltage arrester type-2 consisting of base element with remote indicator contact and ground connectors, for mounting on NS 35/7.5, nominal voltage: 320 V AC, 2 + 1 circuit enclosed in a PVC enclosure suitable for wall mounting complete all as specified and as directed.

Supply and lay Shingle or gravel 50mm size near LT Panels, Substations or at any directed location for fire protection of Out door LT Panel complete all as specified and as directed

Supply and lay Bricks; common burnt clay building bricks, sub-class ‘A’ designation 75 all as specified and as directed for fire protection of Out door LT Panel complete all as specified and as directed

Sand cushioning and spreading clean, dry, fine river sand for LT panel base over which gravel to be placed, including gentle punning and consolidating around the complete all as specified and directed for fire protection of Out door LT Panel complete all as specified and as directed (Note :- Only punned down thickness shall be measured for payment).

M&L for fabrication/welding/Jointing work in existing LT Panel by providing new hinges in place of defective hinges, replacement of locking arrrangement of external door, replacement of main door gasket, replacement of rusted sheet cover including cutting, bending, Welding/soldering and refixing properly at site. Servicing and maintenance of the panel by taking out the incoming connection and all outgoing connection and outgoing cables of the panel and fixing a fresh with proper crimping/tapeing, lux/connector, cable glande including doing all necessary wiring in the panel. Note -Excavation and earth work wherever necessary is deemed to be inculded alongwith the cost and MS Sheet will be measured and paid seperately under respective item

Dismantling, taking down and removing the old existing un serviceable non-functional / broken hinges of any description and in any position of existing feeder pillar boxes/panel boards etc and supply and fixing new cold rolled medium weight mild steel hinges in position as per existing requirement with necessary spot welding, screwing etc including making necessary adjustment for free and smooth movement of panel and locking arrangements complete all as specified and directed.

Taking out old unserviceable insulator from LT panel boards, supply, fixing & testing conical/single bus bar system epoxy insulator including nuts, bolts and washers suitable for LT 415 Volts, 50 Hz AC supply for mounting of bus bars in LT panels/feeder pillar boxes complete all as specified and directed

Replacement of existing unserviceable/damaged part/portion of the existing feeder pillar box/ panel boards with supply and fixing new part or portion fabricated out of 3 mm thick MS sheet in position including making necessary adjustments and alignments to make the existing feeder pillar box/panel board body to required shape and size(s) and MS sheet painted both sides with two coats of synthetic enameled paint over a coat of red oxide primer with necessary filler coating complete all as specified ant directed.

Disconnecting and taking out old existing unserviceable Phase indicator lamps and supply, fixing, connecting and, testing LED type Phase indicator lamp with showing red, yellow and green colours of 22.5mm dia fixed to monitor on LT panel board suitable for 240 Volts AC supply and making connections with using suitable size copper cables wires and lugs complete all as specified and directed.

M & L for preparation of old steel surfaces of steel/LT panel boards/feeder pillar boxes of size upto 1000mm x 1100mm x 450mm of any description & any position including removing disintegrated/detoriating part of paint and applying filler coat to obtain smooth surfaces and applying a coat of synthetic enamel paint using spray machine to obtain smooth finish to the entire satisfaction of Engineer-in-Charge complete all as specified and directed.

All as per item No 19 here-in-before but of size above 1000mm x 1100mm x 450mm less than 1300mm x 1450mm x 450mm complete all as specified and directed.

All as per item No 19 here-in-before but size of above 1300mm x 1450mm x 450mm complete all as specified and directed.

Supply and fix in repair Switch fuse unit of the existing make and model 800 Amp 4 pole, including Fuses complete all as specified and as directed. Note: The cost of taking down the existing unit is deemed to be included in the quoted rate.

S&F in replacement 8 Watt LED bollard light one meter long with Opel acrylic diffuser and IP-65 protection, including necessary concrete work, complete all as specified and directed. Note:- The cost of the necessary PCC base, connecting LT cable with proper terminal is deemed to be included in the quoted rate..

Supply and replace in repair Aesthetically designed LED post Top with aluminium enclosure, powered with high power LEDs as light source and die-cast heat sink exhibits classic Victorian look with symmetrical light distribution and excellent heat dissipation for long life.25 Watt capacity complete all as specified and as directed

M&L for Earthing complete for poles/ DBs with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 m deep below normal ground level with top edge of earth plate, not less than 1.5 m below normal ground level, connected to galvanised iron earth strip of size 25x4 mm by means of bolts, nuts/check nuts and washers etc of galvanised iron, protected by galvanised iron pipe light grade 15 mm dia upto a length of 7.5 m away from earth electrode and connected to main switch/control board including necessary excavation & earth work in any type of soil and PCC 1:3:6 type C1 for earth chamber, 40 mm thick RCC cover slab 1:2:4 type B1 with 6 mm dia TMT Bars at 140 mm c/c both ways, watering pipe 20 mm dia light grade GI, funnel, wire mesh, lugs, charcoal and common salt etc complete all as shown in Electrical plate No. 3 of SSR Part I and testing complete including taking down the old unserviceable earthing complete all as specified and directed. Note:- (i) GI strip and GI pipe medium grade, up to 7.5mtr shall be deemed to be included in the rates quoted for earthing. (ii) Excavation and earth work in any type of soil strata shall be deemed to be included in rates quoted for earthing.

M&L for Earthing complete for panels with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 m deep below normal ground level with top edge of earth plate, not less than 1.5 m below normal ground level connected to galvanised iron earth strip of size 32x6 mm using bolts, nuts/check nuts and washers etc of galvanised iron, connected to main switch/control board including necessary excavation & earth work in any type of soil and PCC 1:3:6 type C1 for earth chamber, 40 mm thick RCC cover slab 1:2:4 type B1 with 6 mm dia TMT Bars at 140 mm c/c both ways, watering pipe 20 mm dia light grade GI, funnel, wire mesh, lugs, charcoal and common salt etc complete all as shown in Electrical plate No. 3 of SSR Part I and testing complete including taking down old unserviceable items complete all as specified and directed. Note:- (i) GI strip and GI pipe medium grade, up to 7.5mtr shall be deemed to be included in the rates quoted for earthing. (ii) Excavation and earth work in any type of soil strata shall be deemed to be included in rates quoted for earthing.

S&F Earth continuity conductor or main earthing lead of size 4 mm dia galvanised iron wire for fixed to poles/DBs complete all as specified and directed.

S&F Earth continuity conductor or main earthing strip of size 32x6 mm of galvanised iron for fixed to poles/DBs/Panels complete all as specified and directed.

M&L for preparation of old painted surfaces of LT steel tubular pole/strut, of any description and in any position 9.00/8.50 Mtr height and scrapping of pole with emery paper and applying one coat of aluminium paint on all the metallic surfaces including protection pipe, cross arms, clamps, GI pipe bracket of street/security light, anti climbing devices etc and providing three Nos radium band strips complete all as specified and directed.

Supply and fixing in repair PVC insulated and PVC sheathed twin core Aluminium conductor of size 06 Sqmm for connecting from bus bar box to street light fittings/ OH line to street light fitting complete all as specified and directed.

Supply and fixing in replacement energy saving environment friendly, long life exclusive innovative die cast aluminium IP-65 flood light 70 Watt LED 6000K with high power LEDS as light source complete including suitable fixing arrangement on pole, pillar, wall with suitable fasteners, nut, bolts, clamps and making connection with three core copper conductor cable not less than 1.5 sqmm complete all as specified and directed.

Supply and fixing in replacement energy saving environment friendly, long life exclusive innovative die cast aluminium IP-65 flood light 100 Watt LED 6000K with high power LEDS as light source complete including suitable fixing arrangement on pole, pillar, wall with suitable fasteners, nut, bolts, clamps and making connection with three core copper conductor cable not less than 1.5 sqmm complete all as specified and directed.

Supply and fixing in replacement energy saving environment friendly, long life exclusive innovative die cast aluminium IP-65 flood light 120 Watt LED 6000K with high power LEDS as light source complete including suitable fixing arrangement on pole, pillar, wall with suitable fasteners, nut, bolts, clamps and making connection with three core copper conductor cable not less than 1.5 sqmm complete all as specified and directed.

Supply, fixing in replacement, connecting and testing in replacement integral LED High bay light luminaries at any height of building/Hangar ranging from 3m to 16 m, 150 watts, with scondary optics made in pressure die cast housing and heat sink in aluminium extrusion with IP66 with mounting bracket and all accessories and connecting the same to electric source with using copper conductor 1.5 Sq mm PVC insulated flexible three core cable, including all accessories and fixing the light fitting to walls/ ceiling etc complete all as specified and directed.

Supply and fixing in replacement LED well glass fitting 1x120 Watt flame proof, CMIFR or any other certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2, and IP 65 protection with die-cast aluminum housing with heat-resistant toughened glass driver, connector, etc. Complete with all accessories prewired and including connecting up at any location, any height at Hangars, including three core flexible copper conductor cable with suitable size, complete all as specified and as directed. Note: The Cost of necessary T&P for fixing the lamp fitting is deemed to be included in the quoted rate.

S&F in repair MCCB, 4 pole, 630 Amps current rating and ultimate breaking capacity Icu = 36 KA with adjustable overload setting and having thermal magnetic release and to be fixed in distribution board, complete all as specified and directed.

All as per item No 52 here-in-before, but MCCB, 4 pole, 400 Amps current rating and ultimate breaking capacity Icu = 36 KA.

All as per item No 52 here-in-before, but MCCB, 4 pole, 315 Amps current rating and ultimate breaking capacity Icu = 36 KA.

All as per item No 52 here-in-before but MCCB, 4 pole, 250 Amps current rating and ultimate breaking capacity Icu = 36 KA

All as per item No 52 here-in-before, but MCCB, 4 pole, 160 Amps current rating and ultimate breaking capacity Icu = 36 KA

All as per item No 52 here-in-before but MCCB, 4 pole, 125 Amps current rating and ultimate breaking capacity Icu = 16 KA

All as per item No 52 here-in-before, but MCCB, 4 pole, 100 Amps current rating and ultimate breaking capacity Icu = 16 KA

All as per item No 52 here-in-before, but MCCB, 4 pole, 63 Amps current rating and ultimate breaking capacity Icu = 16 KA Note for item no 52 to 59 :- All the MCCBs shall be Ics 100% of Icu

Supply and replace steel plates, plain or chequered, 5mm thick or over in thickness in given sizes complete for covering cable ducts inside the sub stations or in any other locations of Hangers complete all as specified and directed. .

M&L for PCC (1:4:8) (using 40mm graded aggregate) type D-2 for foundation of poles struts & stay assembly etc all as specified & directed.

Supply fixing testing and comissioning microprocessor based Air Circuit breaker type CNCS 2000 C 50 KA EDO(Electrical draw out) Microprocessor Based Release - SR18 & SR18G including Overload, shortcircuit and Earth fault protection type matching with existing make and model for fixing in the existing LT panel 4 pole 2000 Amp 50 K A with 2NO+2NC Aux contact for EDO & 6NO+6NC Aux contact and Safety shutter assembly, Racking handle, Door sealing frame, Push-button cover & Rating error preventor including taking down old ACB complete all as specified and as directed. Note:- The cost of any other accessories not mentioned but required for the successful fixing and commissioning of ACB is deemed to be included in the quoted rate.

Supply and fix in repair ON/OFF Load change over switch 415V in sheet metal enclosure 4 pole, 250 Amps Capacity, complete including necessary fixing accessories on wall/panel, complete all as directed.

Supply and fix in repair ON/OFF Load change over switch 415V in a sheet metal enclosure, 4 pole, 125 Amps Capacity, complete including necessary fixing accessories on wall/panel, complete all as directed.

Supply, Installation, Testing and Commissioning CPRI approved cubical type LT Panel floor mounted out door type for 415V, 3 phase 4 wire system 50 Hz AC supply with Copper bus bar duly colour coded of suitable size, for neutral supported with DMC/SMC insulators colour coded with heat shrinkable sleeve having short circuit current with stand minimum 21 KA for one second complete connection from bus bar to breakers with suitable copper cable , factory made fabricated with CRCA sheet totally enclosed, dust weather and vermin proof for outer shell and 2 mm thick for inner shell having TPN cpper bus bar rating 1.5 times that of controlling MCCB supported on SMC insulator with short circuit withstand capacity 35 MVA for 1 second, bottom base channel MS section not less than 100mm x 50mm x 5 mm thick, entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos earth stud, solid connection from main bus bar to switchgears with required size of copper wiring with minimum 1.5 Sqmm PVC insulated copper conductor cable , cable alleys, cable gland plates in two half , general construction confirming to IS-8623/93 and mounted on suitable PCC foundation for the complete panel base with follwoing detailed specification & control i including dismantling of old LT panel and removing from site, complete with suitable fixing accessories. The panel board shall be fabricated from the reputed CPRI approved firm and shall be suitable to accommodate the following complete all as specified and directed :-

OUTER SHELL :- The outer shell shall be made of 3.0 mm thick CRCA body & MS angle section 50x50x6 mm frame with front & back openable, single door system lockable/ openable by keys from both sides having flush pattern fancy locks with louvers & air vent gasket for natural flow of air. The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequite size of glands. The dimension of the outer shell should be adequate to accomodate inner shell described below figing 50 mm space all around and shall be fabricated in such a way that the complete inner shell alongwith its control gears and accessories should be taken outside without disturbing outer sheel. The outer shell shall be mounted on a zinc metal coated stand. Provision of threaded earthing studs at bottom and lifting lugs of suitable size at top to lift the feeder pillar box safely shall be made. Computer cut self adhesive vinly danger notice plate having conventional symbol of bone and skull shall be providid. The degree of protection of outer shell shall be IP-54.

INNER SHELL :- Inner shell shall be made of 2.0 mm thick CRCA body compartmentalized for each control gear, front openable single door system lockable/openable by keys from both sides having chromium plated fancy locks (2 Nos in each compartment) having louvers and air vents gasket for natural flow of air "U' type gasket shall be used to make the inner shell completely vermin proof and to accomodate incomer/outgoing MCCB's and TPN copper bus bar and extension links of rating not less than the 1.5 times rated capacity of the respective MCCB's. The TPN bus bar and extension links shall be insulated with colour coaded heat, shrikable sleeve and shall be mmounted on suitable size 'F' class through out the length of the TPN bus bar. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bone and skull shall be providid on bus bar chamber. All control wires shall be with not less than 1.5 Sqmm multistranded copper conductor FRLSH and shall be properly bunched. tied, ferruled for proper identification and crimped with adequite size of lugs. The cubical shall have a bottom channel of size 75x50mm duly coated with zinc metal coating. A detachable predrilled gland plate of thickness 3.15 mm zinc metal coated should be used at the bottom, indicating lamps LED type, 230 Volt, AC at the incomer of the unit to show three phase availablity at the incomer. An inspection lamp with 11 Watt CFL shall be fitted on top side of inner shell. The degree of protection for inner shell shall be IP-42 and carry the following controls. :-

(A) Incoming:- (a) MCCB 4P,400A, 50 KA -01(Electronic/Microprocesssor type) (c) Indicating lamps for three phases - Qty 1 set of 3 Nos (e) Power lamp inside the panel, along with a connection from the incoming power supply. (B) Out going:- (a) MCCB 3P, 160A, 26KA -01 No (Adjustable magnetic type) (b) MCCB 3P, 100A, 16KA -06 No (Adjustable magnetic type)

Description of item of panel as per item No 65 above, but with the following switch gears with incoming and outgoing (A) Incoming:- (a) MCCB 4P,200A, 36 KA -01 (Electronic/Microprocesssor type) (c) Indicating lamps for three phases - Qty 1 set of 3 Nos (e) Power lamp inside the panel, along with a connection from the incoming power supply. (B) Outgoing:- (a) MCCB 3P,100A, 25KA -02No (Adjustable magnetic type) (b) MCCB 3P, 63A, 16KA -01No (Adjustable magnetic type)

Description of item of panel as per item No 65 above but with the following switch gears with incoming and outgoing at Tech Point (A) Incoming:- (a) MCCB 4P,250 A, 25 KA -01 (Electronic/Microprocesssor type) (c) Indicating lamps for three phases - Qty 1 set of 3 Nos (e) The Power lamp inside the panel and a connection from the incoming power supply. (B) Outgoing:- (a) MCCB 3P, 100A, 16KA -03No (Adjustable magnetic type) Note for item No 65 to 67:- 1. The rate includes the cost of earth work and PCC for grouting the panel with angle iron of size 50 x 50 x 6 mm, 30 CM below the ground level and 40 CM above the ground level 2. All the MCCBs shall be Ics 100% Icu.

AUTOMATION AND SWITCHGEAR PANELS (BID ID -3364611)

Akarsha Enterprises (BID ID -3364562)

M/S uneversal agency (BID ID -3356483)

M/s Anupam Construction Co. (BID ID -3355909)

M/S STEAD FAST (BID ID -3364809)

m/s varsha traders (BID ID -3364317)

Om Electricals (BID ID -3355095)

M/S KAPIL CONSTRUCTION CO (BID ID -3354732)

M/s Shanti Enterprises (BID ID -3364547)

Kumar Sales Corporation (BID ID -3353923)

BABA DEVELOPERS (BID ID -3364693)