Construction work of Lokmata Devi Ahilya Bai Holkar Memorial Gate near Loni Border Bus Depot.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed all kinds of soil as per DSR-2023 S.I. No.2.1.1.

Disposal of moorum/ building rubbish/ malva /similar unserviceable' dismantalled waste materials including loading] unloading and cartage upto 10 Km for Municipal permisices all complete work as per DSR-2023 S.I. No.1.1.18.

cement concrete in foundation in 1:4:8 (with cement, coarse sand & graded stone aggregate nominal 40mm size) of including supply of all materials, labour. Tools& plants etc. required for proper completion of work. as per DSR-2023 S.I.No.4.1.8.

Providing and laying in position specified grade of reinforcement cement concrete excluding the cost of centering ]shutterin and finishing & reinforcement all works upto plinth level. in proportion of 1:1.5:3 with cement] coarse sand and 20 mm gauge stone Grite (Zone-III). as per S.I.No.289.as per DSR-2023 S.I.No.5.1.3.

steel reinforcement for R C C work including strainthening cutting bending placing in position and binding all complete upto plinth level DSR 5.22A.6

Providing and fixing of foundation bolt of 25 mm nominal dia including Nuts and washers complete for for tubular pipe as per DSR-2023 10.20.

Structural steel work in single section fixed with or without connecting plate] including cutting] hoisting] fixing in position and applying a primer coat of approved steel primer as per DSR-2023 S.I.No.-10.1.

Steel work in built up tubular ( Round, square or rectangular hollow tubes etc.) trusses with hot finished seamless type tubes etc. including cutting, hoisting,fixing in position and applying a primming coat of approved steel primer, including welding and bolted with special washers etc. copmlete as per DSR.No.10.16.2.

Providing and fixing of Retro-Reflective Sheeting type-IV with 4 mm thick ACM Single side reflective signs with a corrosion resistant 4 mm thick with 0.40to 0.50 mm both side Aluminium composite Panelface to be fully covered with high intensity prismatic sheeting type--IV as per IRC-67:2012 Retro reflective sheeting with back frame M.S.Angle of 35×35×5 mm, legends, letters. numerals and boarders etc. should be as per Morth specifications No.801.3.7. The sheeting shall have a pressure-senstiveadhesive of the aggressive- tack type requiring no heat, solvent other prepration for adhesion to a smooth clean surface, in a mannerrecommende by the sheeting manufactirer. the ACM (Aluminium composite materials) shall be fixed on the back frame M.S.Angle with rivetting, Micri Prismatic type-IV Retro reflecting sheeting confirming to ASTM D4956-09 shall be pressure fixed . The Retro Reflective Sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflective daytime colour and luminance, shrinkage, flexibility, linear,removal, adhesion,impact resistance,specular Gloss and fungusresistance,3 year outdoor weathering and its having passed these tests shall be obtained from International/ Government Laboratory/ Instititeby the manufacturer of the sheeting and in case of certificate is obtained from International conditions, It should also be from Indian conditions.within 3 years of launching the Products by the manufacturer in abroad. Alternatively, a certificate confirming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirement from a reputed Laboratory. In India can be accepted provesionally . In such a situation The Employer/ Client, if so desire, could sheek for a performance guarntee which would be released after receipt of certifiate meeting the requirement of three outdoor weathering of the sheeting as per IRC 67:2012 & proof of the same report shall be uploaded which quotting tender. The rate shall include all materials, labour. T&P etc. Transportation, Installation and Incidentals all complete as per direction Engineer-in-charge. as per UPPWD SOR-2022 S.I.No.22.10 Morth-801.

Finishing with apoxy paint on steel works (two or more coat) at all locations and applied as per manufacturersspecifications including appropraite priming coat] prepration of surface] etc. complete as per DSR-2023 S.I.No.13.52.1.