SPECIAL REPAIR TO BATHROOMS AND TOILETS AT BLDG NO P-1553, 04 X TOILETS AT BLDG NO. 1490 A AND OTHER MINOR WORKS IN CERTAIN UNITS AT MIL STN, JAISALMER

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified & directed by Engineer-in-charge.

M&L for 25mm thk PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in subbase of floors & finishing the surface even & smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 complete all as specified & directed by Engineer-in-charge.

S&F glazed ceramic coloured tiles of size 350 x 250mm x 7mm / 450mmx350mmx7mm thick on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick backing coat in CM (1:4) complete all as specified and directed by Engineer-in-charge.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L for rendering 15 mm thick, plaster in cement mortar (1:6) on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing and finishing the surface even and fair without using extra cement all as specified & directed by Engineer-in-charge.

M&L for rendering 15 mm thick plaster in cement mortar (1:6) on fair faces of brick work or concrete surfaces of walls and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge.

Taking down chowkats or frames (without taking off shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames (without taking off shutters from the frames) area not exceeding 1.5 Sqm each complete all as specified & directed by Engineer-in-charge.

S&F second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified & directed by Engineer-in-charge.

S & F, 35 mm thick second class hard wood factory made plain, framed, panelled shutters, with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and Style as per IS:1003 (Part-1), kiln seasoned and chemically pressure treated all as specified & directed by Engineer-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified & directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with single piece extruded PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement of single piece extruded PVC profile for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F 150 mm size aluminium anodised barrel tower bolts of extruded section all as specified & directed by Engineer-in-charge.

S&F 150 mm size aluminium handle, cast type, anodiesed complete all as specified & directed by Engineer-in-charge.

S&F 125 mm size aluminium handle, cast type, anodiesed complete all as specified & directed by Engineer-in-charge.

S&F, 100mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed by Engineer-in-charge.

S&F, 75mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed by Engineer-in-charge.

S&F, 3mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each panes and including hacking out old broken glass of any thickness size, quality or description from metal frames complete all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

S&F, 3mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each panes and including hacking out old broken glasses (any thickness, size, quality or description) from steel/wooden frames complete all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

M&L for preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

S&F in repairs 15mm dia bib taps cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as directed by Engr-in-Charge.

S&F in repairs 15mm dia pillar taps cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe complete all as directed by Engr-in-Charge.

S&F in repairs 15mm dia stop valves fancy type cast copper alloy chromium plated screwed down high pressure with crown or capstan head screwed both ends for iron pipe complete all as directed by Engr-in-Charge.

S&F in repair 20mm bore stop valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repair 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia & PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC connections 600mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC connections 450mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

S&F in repair, chromium plated, grating for Nahani trap/ floor trap of size 100 mm dia (heavy duty) complete all as specified and directed by Engineer-in-charge.

S&F in repairs brass chromium plated shower rose with swivel joints 125mm dia with 18mm dia chromium plated pipe complete all as specified and directed by Engineer-in-charge.

Taking down GI tubing 15 mm dia with all fitting fixed to wall and ceiling,concelled in walls/ floor etc. complete all as specified and directed by Engineer-in-charge.

Taking down GI tubing 20 mm dia with all fitting fixed to wall concelled in walls/ floor and ceiling etc. complete all as specified and directed by Engineer-in-charge.

S&F 15mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc complete all as specified and directed by Engineer-in-charge.

S&F 20mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc complete all as specified and directed by Engineer-in-charge.

Refixing old steel tubing including cleaning and connections in new or old position (Wall, ceiling, floors etc) of the size 15mm bore complete all as specified & directed by Engineer-in-charge.

Refixing old steel tubing including cleaning and connections in new or old position (Wall, ceiling, floors etc) of the size 20mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair, vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest (Excluding flushing cistern and flush pipe) and making good to the floor complete all as specified & directed by Engineer-in-charge.

S&F in repair wash hand basin oval type vitereous china flat back size 550 x 400 mm white including waste fittings, brass, chromium plated, coupling, waste pipe, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550 x 400 mm white including waste fittings, brass, chromium plated, coupling, waste pipe, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tanks 1000 litres capacity triple layered (White) cylindrical vertical with closed top hoisted and 20mm ball valves high pressure with polythene float and flynut complete fixed in position including dismantling water tank of capacity exc 500 lt but n exc 1000 ltand removing to store of any description complete all as specified & directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tanks 2000 litres capacity triple layered (White) cylindrical vertical with closed top hoisted and 25mm ball brass valves high pressure with polythene float and flynut complete fixed in position including dismantling water tank of capacity exc 1000 lt but n exc 2000 ltand removing to store of any description complete all as specified & directed by Engineer-in-charge.

S&F in repair 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair, 15 mm bore, stop cock, fancy type, chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repair, vitreous china urinals with urinal spreader, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing complete all as specified & directed by Engineer-in-charge.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed by Engineer-in-charge.

M&L for rendering 10 mm thick plaster in cement mortar (1:4) on concrete surfaces of ceiling and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for rendering 5 mm thick in CM (1:4) on fair faces of concrete surfaces as in ceiling finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of white wash on walls over a coat of alkali resistant primer complete all as specified & directed by Engineer-in-charge.

M&L for preparing new plastered or unplastered surfaces and applying three coats of white wash on wall all as specified & directed by Engineer-in-charge.

M&L for preparing new plastered or unplastered surfaces and applying three coats of white wash on ceiling all as specified & directed by Engineer-in-charge.

S&F steel window with side hung shutters fitted with box type hinges including MS handles, peg stays, MS guard bar made out of 10 mm squre bar, glazing bars dovetailed or welded for receiving glass and including painting with one shop coat of zinc chromate primer including cutting holes in wall for fixing the window lugs in PCC 1:2:4 type B1 using 20mm graded aggregate and making good the disturbed surfaces in CM (1:3) and applying two coats existing wall finishes to match with existing colour complete all as specified & directed by Engineer-in-charge. Note : The rates quoted are inclusive of making good all the disturbed surfaces to match with the adjoining surfaces and necessary scaffolding etc up to 4th floor.

S&F steel ventilators with top hung shutters fitted with box type hinges including MS peg stays, MS handle and glazing bars dovetailed or welded for receiving glass including painting with one shop coat of zinc chromate primer,and cutting holes in wall for fixing the window lugs in PCC 1:2:4 type B1 using 20mm graded aggregate and making good the disturbed surfaces in CM (1:3) and applying two coats existing wall finishes to match with existing colour complete all as specified and directed by Engineer–in-charge. Note : The rates quoted are inclusive of making good all the disturbed surfaces to match with the adjoining surfaces and necessary scaffolding etc up to 4th floor.

S&F pressed steel frames (size 105 x 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified & directed by Engineer-in-charge.

S&F 35 mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides all as specified & directed by Engineer-in-charge.

S&F, Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed by Engineer-in-charge.

M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

M&L for preparing old wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint (Ordinary tint) complete all as specified & directed by Engineer-in-charge.

Resecuring or easing & adjusting without taking down shutters of any description exc 1 sqm but n exc 2 sqm each complete all as specified & directed by Engineer-in-charge.

S&F in repair steel window handle left and right complete fitting complete all as specified & directed by Engineer-in-charge.

S&F in repair steel window stopper peg stay complete fitting complete all as specified & directed by Engineer-in-charge.

M&L perpartion of old existing wall surfaces including cornices, plastered or un-plastered surfaces by brooming down or steel wire brushing, moss efflorescent salt and trading oil and greasy spots and applying one coat of cement base paint over and including filling up of holes by wall care putty wherever required complete all as specified & directed by Engineer-in-charge.

M&L perpartion of old existing wall surfaces including cornices, plastered or un-plastered surfaces by brooming down or steel wire brushing, moss efflorescent salt and trading oil and greasy spots and applying one coat of white wash on wall over and including filling up of holes by wall care putty wherever required complete all as specified & directed by Engineer-in-charge.

M&L perpartion of old existing wall surfaces including cornices, plastered or un-plastered surfaces by brooming down or steel wire brushing, moss efflorescent salt and trading oil and greasy spots and applying one coat of white wash on ceiling over and including filling up of holes by wall care putty wherever required complete all as specified & directed by Engineer-in-charge.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & directed by Engineer-in-charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & directed by Engineer-in-charge.

S&F in repair 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & directed by Engineer-in-charge.

S&F 200 mm size aluminium anodised barrel tower bolts of extruded section complete all as specified & directed by Engineer-in-charge.

S&F in repair, 200 mm size aluminium anodised barrel tower bolts of extruded section complete all as specified & directed by Engineer-in-charge.

Demolition of Cement concrete (unreinforced) Concrete of any description and in any position not otherwise specifically provided for sunken floor and depositing the same at a distance not exceeding 250m away from the outer edge of bldg complete complete all as specified & directed by Engineer-in-charge.

M&L broken bricks filling of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in-charge.

M&L for pain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) mix as filling of sunken floors complete all as directed by Engr-in-charge.

M&L Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete work surfaces finished even and smooth without using extra cement including mixed with water proofing compound complete all as specified & directed by Engineer-in-charge. NOTE: Water proofing compound shall be measured and paid seperately.

Supply only integral water proofing compound complete all as specified & directed by Engineer-in-charge.

M&L for applying two coats of NITOBOND SBR polymer modified coating to a thickness of 1mm, 1st Coat (Nitobond SBR Chemical 1 ltr, Water 2 Ltrs, Cement 3 Kg) Second Coat (Nitobond SBR Chemical 1 ltr, Cement 3 Kg) including preparation thoroughly without any traces of dirt or laitance as in sunken floors complete all as specified & directed by Engineer-in-charge.

Dismantling of 100/75 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified & directed by Engineer-in-charge.

S&F 100mm bore (sand cast pipe) soil, waste and vent pipes in any length with or without ears and jointing with cement & fixed to walls complelte all as specified & directed by Engineer-in-charge.

S&F 75mm bore (sand cast pipe) soil, waste and vent pipes in any length with or without ears and jointing with cement & fixed to walls complelte all as specified & directed by Engineer-in-charge.

S&F, 100mm bore cast iron (sand cast pipe) soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complelte all as specified & directed by Engineer-in-charge.

S&F, 75mm bore cast iron (sand cast pipe) soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complelte all as specified & directed by Engineer-in-charge.

M&L 75 mm size cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 complete all as specified & directed by Engineer-in-charge.

S&F 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & directed by Engineer-in-charge.

S&F 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & directed by Engineer-in-charge.

S&F, 100 mm bore CI branch piece, single, (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified & directed by Engineer-in-charge.

S&F traps 'P' or 'S' suitable for 100mm bore cast iron pipe complete all as specified & directed by Engineer-in-charge.

S&F 75mm bore cast iron cowl (sand cast) complete all as specified & directed by Engineer-in-charge.

S&F, in repair, tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges fixed with chromium plated brass screws complete all as specified & directed by Engineer-in-charge.

S&F in repair plastic EWC seat cover, coloured closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & directed by Engineer-in-charge. (Make :- Cera Model Cat Part No. 2308 or equivalent in Appx 'C' list of make).

S&F in repair for pressure jet for western type water closet with PVC connection 600 t0 900 mm long including brass head screw and suitable washer complete all as specified & directed by Engineer-in-charge.

S&F in repair European type water closet, including plastic seat cover white, closed pattern with flat bottom and mild steel chromium plated or aluminium hinging device complete all as specified & directed by Engineer-in-charge.

S&F in repair CP Health faucet spray with 1.5m long pipe with wall hook & fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair bib taps two way type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm bore and fixed complete all as specified & directed by Engineer-in-charge.

Supply and in repair fix bathroom cabinet with mirror of size 305mm x 95mm x 410mm complete all as specified & directed by Engineer-in-charge.

S&F gun metel, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed for the size 20 mm bore with fittings and accessories. ISI marked and as per IS 14846 including taking down existing gate valve of any description complete all as specified & directed by Engineer-in-Charge

S& F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified & directed by Engineer-in-Charge

Demolition of stone slab & tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar all as specified & directed by Engineer-in-charge.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F in repair, 110mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls complete all as specified and directed by Engineer-in-charge.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors as waste & vent pipes complete all as specified & directed by Engineer-in-charge.

S&F in repair, 110 mm bore (SWR) PVC bends any radius complete as directed by Engr-in-Charge.

S&F in repair, 110 mm bore (SWR) PVC (SWR) junction single, (Single T) equal or unequal complete as directed by Engr-in-Charge.

M & L for special treatment for sunken portion of WCs/bath and toilet executed in the following stages :- Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris outside MD land etc complete. Stage 2 :- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr Fixit or its equivalent make as approved in the proporation/ quantity all as per manufacturer's instructions. Stage 3 :- Apply two coats of water proofing elastomeric liquid membrane of Dr Fixit or by brush application of STP or its equivalent make as approved (The surface after painting one coat shall be allowed to dry for 8 hours before application of next coat) all as per Manufacturer's instructions.

ITEM NO. 102.00 CONTD... Stage 4 :- Rendering 10mm thick in CM 1:3 mixed with integral water proofing chemical of Dr Fixit or its equivalent make as approved in the proportion/ quantity all as per Manufacturer's instructions. Stage 5 :- All CI joints shall filled with mixture of cement fine sand and shalicrete R of STP Ltd or integral water proofing chemical or Dr Fixit or its equivalent make as approved all as per Manufacturer's instructions. Stage 6 :- Making holes in wall/floor and fixing 600mm long 20 mm dia medium grade GI spout for draining the surplus water if any. Stage 7 :- Carry out ponding test for 72 hours to ensure water tightness of repaired sunken portion. Stage 8 :- Sunken floor shall be filled with lean cement concrete PCC (1:5:10) type E2 (using 40mm graded stone aggregate) after satisfactory passing of above mentioned treatment by Engineer-in-Charge.

Excavating in post holes (or similar holes) in any type of soil, each not exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50 Mtr and making good surface complete all as specified & directed by Engineer-in-charge.

M&L for plain cement concrete (1:2:4) type B-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified & directed by Engineer-in-charge.

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde E-250 quality-A) complete all as specified & directed by Engineer-in-charge.

M&L, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc complete all as specified & directed by Engineer-in-charge.

S&F rolled mild steel joist, channel, angle or tee sections, fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length indicated) conform to Fe 410-W (Gde E-250 quality-A) complete all as specified & directed by Engineer-in-charge.

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified & directed by Engineer-in-charge.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes complete all as specified & directed by Engineer-in-charge.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as specified & directed by Engineer-in-charge.

Taking out carefully copper/GI earthing complete including GI pipe with Cu/GI strip and removing materials for taking credit and making good disturbed surface complete all as specified & directed by Engineer-in-charge.

M& L Point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm with 3 mm thick phenolic laminated white sheet cover for mounting of Piano Type switches, sockets, fan regulators complete for the following :-

(a) One light point controlled by one switch.

(b) fan point controlled by one switch.

(c) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(d) One socket outlet 6 amp controlled by one switch on indepdendent board.

All as per item No 112.00 here-in-before but of size cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) for one 16 amp socket outlet controlled by one switch on independent board complete.

S&F switch piano, flush type, 6 amps, 230 volts, single pole, one way complete all as specified & directed by Engineer-in-charge.

S&F switch piano, flush type, 16 amps, 230 volts, single pole, one way complete all as specified & directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete all as specified & directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 3 pin, 6 amp, flush type complete all as specified & directed by Engineer-in-charge.

S&F Ceiling rose, three phase/PVC/polycorbonate, isolated body complete all as specified & directed by Engineer-in-charge.

S&F for MCB DB SPN 12 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified & directed by Engineer-in-charge.

S&F for MCB DB SPN 8 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole and neutral 32 Amps, 240 Volts, 10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole 6 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified & directed by Engineer-in-charge. (Note :- Two runs of 6.00 Sqmm cable & one run of 6.00 Sqmm cable as earth wire and one run of PVC conduit shall be measured and paid as one unit length)

Supply and fixing LED building security light fitting 35 Watt (or above) 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with electronic driver including thermal management in multiple optics complete with IP 65/66 protection complete with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as directed by Engineer-in-Charge.

S&F bracket of GI pipe light grade of 40mm bore dia, 1.2 meter in length, MS clamps made of FI 40 mm x 6mm incl nuts, bolts & washers including two coats of synthetic enamel paint over a coat of zink chrome primer and including taking down existing bracket complete all as specified & directed by Engineer-in-charge.

Supply and fixing of LED box type Integrated Batten 40 watt having Aluminum Extruded housing in white powder coated Finish with high translucent PC Cover, Elegant Design, IP 20 Protection. Dimensions of the Fitting Shall be Not less then 1200 MM (Length) X 40 MM (Width) X 63 MM (Height). Lumens output of the fitting shall be not less then 4400 lm, CCT 5700 – 6500K, buring hours 50,000 Surge Protector 4 KV, PF>= 0.95 , Separate detachable type Electronic constant current drivers for easy replacement and maintenance, THD < 10%, Necessary mounting arrangements .The fixture shall be suitable for wall mounting /suspension mounting as per site requirement . The Manufacturer of the fixture shall have in house NABL Accredited Lab and must produce certificate of the same along with LM-79 / LM80 / Test Report as per Crompton CAT PART NO Shelter . CIS -305-40-57-SL-DP-NWH or equivalent in Appx 'C'list of makes.

S & F of LED tube light fitting 10 watt tube LED Neutral white in colour, 600 mm in length wall mounted LED batten,extruded aluminium heat shink provided for efficient heat dissipation & integrated electronic driver,optic diffused type including all electric connection with whilte flexible cord 1.50 Sqmm 3 core as required complete all as specified and directed.

Supply & fix Steel body heavy duty exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified & directed by Engineer-in-charge.

Taking down exhaust fan of any sweep, dismanting blade and including preparation, filling cavity applying one coat of synthetic enamel paint by spraying with machine, re-assembling the fan body to fan and re-fixing in its original position or any other position complete all as specified & directed by Engineer-in-charge. Note :- Rate quoted by the contractor shall deemed to inclusive of replacing of quarter pin, nut bolt with check nut, rubber real etc.

M & L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground level connected to galvanized iron wire 4 mm dia as earthing lead up to Panel /DB BOX as per site requirement by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection including test point terminal cover the earhing hole by PCC chamber and GI cover and testing on completion complete all as specified & directed by Engineer-in-charge.

NOTE FOR ITEM No. 130.00 [i]. Excavation & earth work in any type of soil including removing of surplus material upto 100M [ii]. PCC (1:3:6) type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC (1:2:4) type B1 cover 50x50 cm with 8mm round bar @ 15 cm C/C both ways. [iii]. Main earthing strip from earth electrode to test point upto 7.5 mtr. [iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs and charcoal & salt as reqd. [v]. GI protection pipe of size 40 mm bore light grade 7.5m.

M&L in repair of for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in pipe or fixed to DBs or any other indicated situation for loop earthing with GI wire 4 mm mm size complete all as specified and directed Engg-in-Charge.

S&F steel water tubing 15 mm bore, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors in trench on pole for protection of cable etc and including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

AMBEY MAA CONSTRUCTION COMPANY

M/S OM VISHNU ENGINEERING & CONSTRUCTION COMPANY

S K TRADER

BHAGWATI CONSTRUCTION

M/S PIYUSH CONSTRUCTION COMPANY

GEMRARAMCONTRACTOR

Leelashah Enterprises