Execution of balanced work in 120 Mens Barrack for Bn. Hqr. At BSF Campus Gaya, Bihar

BILL OF QUANTITY

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

CARRIAGE OF MATERIALS

1 1.1. By mechnical transport including loading, unloading & stacking

a 1.1.1 Lime,moorum,Building rubbish

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not

2 2.8 exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting

out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

a 2.8.1 All kinds of soil. cum 500.00 130.80 65400.00

Earth work in excavation by mechanical means (Hydraulic excavator/manual means in foundation treanches or drains (not

3 2.9 exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting

out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 mtr.

a 2.9.1 Ordinary rock cum 212.00

4 2.26 extra for every additional lift of 15m or part thereof in.

a 2.26.1 All kinds of soil. Cum 65.03 34.60 2250.04

b 2.26.2 Ordinary or hard rock cum 10 62.00 620.00

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in

depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying & stackng of good earth at site including royalty and carriage up to 1 km (earht measured in stacks will be reduced by

20% for Payment).

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish,

lead upto 50 m and lift upto 1.5 m.

a 2.28.1 All kinds of soil. 100 sqm 935.25

9 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

a 2.34.1 Chlorpyriphos/Lindane Emulsifiable concentrate of 20%. Ltr. 50 185.95 9297.50

Diluting and injecting chemical chemical emulsion for POST CONSTRUCTIONAL anti-termite treatment (excluding the cost of

chemical emulsion)

Treatment of soil under existing floors using chemical emulsion @ one ltr. Per hol, 300mm apart including drilling 12mm diameter

holes and plugging with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor.

i 2.35.3.1 With Chlorpyriphos /Lindane E C. 20% with 1% concentration. Sqm 100.00 88.25 8825.00

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to

a 4.1.3 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum 35.98 4514.05 162415.52

b 4.1.6 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) cum 50 3888.20 194410.00

c 4.1.8 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) cum 77.633 3593.30 278958.66

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per Per 50

13 4.12 manufacturer’s specification kg 100 35.35 3535.00

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof

course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal

15 4.17 size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand Sqm 88.00 338.75 29810.00

including finishing the top smooth

16 5.9 Centring and shuttering including strutting, propping etc. and removal of form for:

a 5.9.1 Foundations, footings, bases of columns etc. for mass concrete. sqm 100.00 166.9 16690.00

b 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. sqm 97.27 285.15 27736.54

c 5.9.3 Suspended floors, roofs, landings, balconies and access platform. sqm 78.24 311.2 24348.29

d 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 265.66 262.25 69669.34

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

e 5.9.6 Columns, Pillars, Piers, Abutments, posts and Struts Sqm 32.37 365.6 11834.47

f 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 16.00 326.3 5220.80

g 5.9.13 Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards. Sqm 50.00 470.1 23505.00

h 5.9.16 Edges of slabs and breaks in floors and walls.

17 5.9.18 Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like sqm 70.09 398.35 27920.35

18 5.9.19 Weather shade, chajjas, corbels etc. including edges. sqm 150.00 411.1 61665.00

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth

a 5.22.6 Thermo-Mechanically Treated bars kg 500.00 62.25 31125.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above

a 5.22A.6 Thermo-Mechanically Treated bars kg 17500.00 62.25 1089375.00

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced

cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but

excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per

21 5.33 IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of

Engineer-in-charge.

(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is

payable/recoverable separately).

a 5.33.1 All works upto plinth level. cum 10.00 5242.15 52421.50

b 5.33.2 All works above plinth level upto floor V level. cum 120.00 5781.5 693780.00

22 6.1 Brick work with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in foundation & plinth in:

a 6.1.2 Cement mortar 1:6 (1 cement: 6 coarse sand) cum 110.00 3316.55 364820.50

23 6.15 Extra for providing and placing in position 2 Nos. 6 mm dia MS bars at every third course of half brick masonry (with FPS bricks) Sqm 139.71 63.3 8843.64

Brick work with mechanized autoclaved flyash sand lime non modular bricks conforming to IS : 12894 of class desiganation 10 in

superstructure above plinth level up to floor V level :

a 6.42.2 Cement mortar 1:6 (1 cement: 6 coarse sand) cum 4679.45

half brick masonary with non modular mechanized autoclaved flyash sand lime bricks of class desiganation 10 , conforming to IS :

12894 in superstructure above plinth level up to floor V level

a 6.46.2 Cement mortar 1:4 (1 cement: 4 coarse sand) sqm 568.75

Brick edgeing 7cm wide 11.4cm deep to plinth protection with brick of class desiganition 75 including grouting with cement mortar

1:4 ( 1 cement: 4 fine sand )

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms,

vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm

thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy

touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

a 8.2.1 White marble - Raj Nagar plain /udaipur green marble /zebra black marble

i 8.2.1.2 Area of slab over 0.50 Sqm Sqm 90.00 1980.8 178272.00

b 8.2.2 Granite of any colour and shade

i 8.2.2.2 Area of slab over 0.50 Sqm Sqm 65.00 3083.4 200421.00

Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss

finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen platfrom, vanity counters and

29 8.5 similar location in marble / Granite / stone work including necessary holes for pillar taps etc. Including rubbing and polishing Each 42.00 281.1 11806.20

necessary etc. complete.

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board

30 9.21 construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands

and face veneers on both faces of shutters :

a 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. sqm 132.00 1578.3 208335.60

b 9.21.3 25mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws. sqm 60.00 1266.75 76005.00

31 9.22 Extra for providing and fixing flush doors with decorative veneering:

a 9.22.1 On one side in item no. 9.21 Sqm 262.00 371.7 97385.40

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all

area of door shutter to be measured).

Providing and fixing wire gauze shutters using galvanised MS wire gauze of average width of aperture 1.4mm with wire of dia,

0.63mm for doors, windows and clerestory windows including ISI marked stainless steel butt hinges with necessary screws.

a 30 mm thick shutters

i 9.29.1 Second class teak wood Sqm 60.00 2412.7 144762.00

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including

priming coat with approved steel primer all complete

a 9.48.1 Fixed to steel windows by welding. Kg 200.00 90.75 18150.00

b 9.48.2 Fixed to opening /wooden frames Kg. 2000.00 98.2 196400.00

34 9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868)

transparent or dyed to required colour or shade with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 )

transparent or dyed toreqired colour or shade with necessary screws etc.

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per

IS :1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

a 9.101.2 Twin rubber stopper Each 69.00 71.55 4936.95

Providing & fixing bright finished brass 100mm mortice latch and lock with 6 levers and a pair of lever handles with necessary

screws etc. complete (Best make of approved quality).

Providing & fixing special quality bright finished brass Cupboard or ward robe locks with four levers including necessary screws

etc. complete (best make of approved quality).

Providing & fixing IS:3564 marked aluminium Die cast body tubular type universal hydraulic door closer with necessary accessories

and screws etc. complete

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions

and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

a 10.5.2 Using flats 30x6mm for diagonal braces and central cross piece. sqm 5.00 2427.15 12135.75

Providing & fixing factory made ISI marked steel glazed doors, windows and ventilators side/top/central hung with beading and

all members such as F7D , F4B, K11B and K12B etc. complete of standard rolled steel sections, joints mitred and flash butt welded

43 10.11 and sash bars tenoned and riveted , including providing and fixing of hinges, pivots,including priming coats of approved steel

primer , but excluding the cost of other fitting , complete as per approved design ( ( Sectional weight of only steel members shall

be measured for payment ).

Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6

graded stone aggregate 20 mm nominal size).

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing pressed steel door frames conforming to IS:4351 manufactured from commercial mild steel sheet of 1.60 mm

thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x 25 mm, or base

44 10.14 ties of 1.60 mm pressed mild steel welded or rigidly fixed together by mechanical means, including M.S pressed but hinges 2.5 mm

thick with mortar guards , lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-

treatment of the surface as directed by the Engineer-in-charge.

a 10.14.1 Profile B

i 10.14.1 Fixing with adjustable lugs with split end tail to each jamb Mtr 330.00 346.75 114427.50

b 10.14.2 Profile C

i 10.14.2.2 Fixing with adjustable lugs with split end tail to each jamb Mtr 250.00 370 92500.00

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded,

including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6

graded stone aggregate 20 mm nominal size).

Providing and fixing circular/hexagonal cast iron or MS sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid

of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ MS box by

means of 3.3mm dia round headed screws, one lock at the corners. Clamps shall be made of 12mm dia M.S. bar bent to shape as per

standard drawing.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer using structural steel etc. as required.

47 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. kg 300.00 77.9 23370.00

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar

works, including applying a priming coat of approved steel primer.

49 10.3 Providing and fixing glass panes with putty and glazing clips in steel doors,windows,clerestory windows,all complete with:

a 10.30.1 4mm Thick glass panes sqm 5.00 657.75 3288.75

Providing and fixing stainless steel ( grade 304 )railing made of Hollow tubes , channels , plates etc , including welding grinding ,

buffing ,polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts

50 10.28 complete ,I/c fixing the railing with necessary accessories &stainless steel dash fasteners ,stainless steels bolts etc ,of required size Kg 400.00 558 223200.00

,on the top of the floor or the side of waist slab with suitable arrangment as per approval of Engineers -in-charge, ( for payment

purpose only weight of stainless steel members shall be considered excluding fixing accesories such as nuts ,bolts, fasteners etc

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement

including cement slurry, but excluding the cost of nosing of steps etc. complete.

a 11.3.1 40mm thick with 20mm nominal size stone aggregate Sqm 100.00 280.05 28005.00

Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat

53 11.13 Providing and fixing glass strips in joints of terrazo/ cement concrete floors

a 11.13.1 40 mm wide and 4 mm thick Mtr. 100.00 29.4 2940.00

Marble stone flooring with 18mm thick marble stone as per sample of marble approved by Engineer-in-charge over 20 mm

54 11.23 (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and

polishing complete with :

a 11.23.5 Udaipur green marble Sqm 200.00 1418.95 283790.00

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to

match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement

56 11.27 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and sqm 280.00 954.1 267148.00

polishing complete.

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of

approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in

skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey

cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete

Providing & laying rectified glazed ceramics floor tiles 300x300mm or more (thickness to be specified by the manufacturer) of Ist

58 11.39 quality conforming to IS:15622 of approved make in colours White, Ivory, Grey, Fume, Red Brown, laid on 20 mm thick cement sqm 260.00 931.5 242190.00

mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

Providing & laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less

59 11.41 than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1

cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of

60 12.19 integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and

finished neat :

a 12.19.1 With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 sqm 100.00 283.65 28365.00

Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with

61 12.2 cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound laid over a bed of 20 mm thick sqm 100.00 431.9 43190.00

cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including

finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

a 12.21.1 In 75x75mm deep chase metre 200.00 109.45 21890.00

Making khurras 45x45 cm with average minimum thickness of 5 cmcement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

63 12.22 aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse each 8.00 148.75 1190.00

sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing MS holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement

64 12.38 concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement:2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of

cutting holes and making good the walls etc.

65 12.39 Providing lead caulked joints to sand cast iron rain water pipes and fittings:

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with

seal ring conforming to IS:5382 leaving to 10mm gap for thermal expansion. (i) Single socketed pipes:

Providing and fixing on wall face unplasticised- PVC moulded fittings/accessories for unplasticised-Rigid PVC rain water pipes

conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving to 10mm gap for thermal expansion.

a 12.42.1 Coupler

c 12.42.6 Shoe (plain)

Providing and fixing unplasticised- PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of

68 12.43 50x50x50mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing in cement

mortar 1:4 (1 cement:4 coarse sand) and making good the walls etc. complete.

69 12.44 Providing & fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighing not less than 440 gms. Each 8.00 32.75 262.00

70 13.4 12mm cement plaster of mix :

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

71 13.7 12mm cement plaster finished with a floating coat of neat cement of mix :

18 mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6mm thick

cement plaster 1:3 (1 cement: 3 coarse sand) finished rough with sponge.

a73 13.16 6 mm cement plaster to ceiling of mix :

74 13.5 15mm cement plaster on rough side of single or half brick wall of mix:

76 13.22 Extra for plastering exterior walls of height more than 10m from ground level for every additional height of 3m or part thereof. Sqm. 200.00 28.85 5770.00

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth

a 13.37 White washing with lime to give an even shade

78 13.37.1 New work (three or more coats) Sqm. 100.00 11.75 1175.00

a 13.41 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

79 13.41.1 New work (two or more coats) over and including priming coat with cement primer Sqm 1600.00 66.7 106720.00

80 13.47 Finishing walls with Premium Acrylic Smooth exterior paint with "Silicone additives of required shade

New work (two or more coats applied @1.43 ltr/10 sqm over and including base coat of water proofing cement paint applied

81 13.6 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

a 13.60.1 Two or more coats on new work Sqm 500.00 60.25 30125.00

82 13.45 Finishing walls with textured exterior paint of required shade

New work (two or more coats applied @ 3.28 Ltr/ 10 Sqm) over and including base coat of water proofing cement paint applied @

83 13.5 Applying priming coat:

a 13.50.1 With ready mixed pink or grey primer of approved brand and manufacturer on wood work ( hard & soft wood) sqm 100.00 25.85 2585.00

Providing and applying two coats of Fire retardent paint unthunned on cleaned wood/ply surface @ 3.5 sqm per litre per coat

including preparation of base surface asper recommendation of manufacture to make the surface fire retardent.

85 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

a 13.61.1 Two or more coats on new work Sqm 600.00 53.85 32310.00

86 13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications

a 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10 sqm. sqm 50.00 78.75 3937.50

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under

coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Forming groove of uniform size from 12x12mm and 25x15mm in plastered surface as per approved pattern using wooden battens,

87 13.76 nailed to the under layer including removal of wooden battens, repair to the edges of panel and finishing the groove complete as Mtr. 500.00 72.15 36075.00

per specifications and direction of the Engineer-In-Charge.

Boring, providing and installing board cast-in-situ reinf. Cement concrete pile of specified diam and length below pile cap in M-25

in cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinf. but including the cost of

81 20.2 boring with bentonite solution and temporary casing of appropriate length for setting out and the pile cap etc. all complete,

including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto the bottom of pile

a) 20.2.1 300 mm dia piles Mtr. 1382.15

Vertical load testing of piles in accordance with IS:2911 (Part-IV) including installatioin of loading platform and preparation of pile

82 20.6 head or construction of test cap and dismantling of test cap after test etc. complete as per specification and the direction of Engineer-

a) 20.6.1 Single pile upto 50 tonne capacity

i) 20.6.1.1 Initial test Per Test 38561.8

ii) 20.6.1.2 Routine test Per Test 17422.5

b) 20.6.3 Group of two or more piles upto 50 tonne capacity

i) 20.6.3.1 Initial test Per Test 56332.8

ii) 20.6.3.2 Routine test Per Test 34264.2

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

ALUMINIUM WORK:

Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/

appropriate Z-sections and other sections of approved make comforming to IS: 733 & IS:1285, fixed with rawl plugs and screws or

with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top bottom and sides with

required of PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred & jointed mechanically wherever

required including cleat angle, aluminium snap beading for glazing/panelling C.P. brass/ Stainless Steel screws, all complete as per

architectural drawings & the directions of Engineer-In-Charge. (Glazing and panelling to be paid for separately).

a 21.1.1 For fixed portion

Anodized aluminium (anodized transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of

fittings wherever required including the cost of PVC/ neoprene gasket required. (Fittings shall be paid for separately)

Anodized aluminium (anodized transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC

Providing & fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked, for doors including

89 21.4 cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece MS sheet outer box with

slide plate etc. complete as per the direction of Engineer-In-charge.

a 21.4.1 With stainless steel cover plate Each 4.00 1953.1 7812.40

Providing & fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and

making good etc. complete.

Providing & fixing aluminium casement window fastener of required length for aluminium windows with necessary screws etc.

a 21.15.1 Anodized( AC15) aluminium. Each 60.00 50.5 3030.00

Providing & fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer-

a 21.16.1 Anodized( AC15) aluminium. Each 60.00 60.95 3657.00

Providing and fixing glazing in aluminium doors, windows, ventilator shutters & partitions etc. with PVC/ neoprene gasket etc.

92 21.3 complete as per architectural drawings and the directions of Engineer-In -Chage (Cost of aluminium snap beading shall be paid in

a 21.3.2 With float glass panes of 5.5 mm thickness Sqm 329.00 905.75 297991.75

b 21.3.3 With float glass panes of 8mm thickness Sqm 5.00 1227.8 6139.00

WATER PROOFING:

Providing and laying water proofing treatment in sunken portion of WCs, bathrooms etc. by applying cement slurry mixed with

water proofing cement comopund consisting of applying: a) First layer of slurry of cement @ 0.488 kg./Sqm mixed with water

proofing cement comound @ 0.253 kg./Sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @

0.242 kg./Sqm mixed with water proofing cement comopund @ 0.126 kg./Sqm. This layer will be allowed to air cure for 4 hours

followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners,

junctions of pipes and masonary with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of

roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of

cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab

including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar

94 22.7 using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix

1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge

to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs

c) After two days of proper curing applying a second coat of cement slurry

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-

charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix1:4 (1 cement :4 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved

quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300

mm square 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing

and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

a) 22.7.1 With average thickness of 120mm and minimum thickness at khurra as 65 mm. sqm 1200.00 786.7 944040.00

NS Supplying and filling in plinth with local sand under floors including watering, ramming consolidating and dressing complete. Cum 50.00 606.23 30311.49

Substitute item

Brick work with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in superstructure above plinth level upto

floor V in all shapes and sizes in :

6.4.2 Cement mortar 1 : 6 (1 cement : 6 coarse sand ) cum 285.96 3876.15 1108439.36

6.12 Half brick masonary with common burnt clay F.P.S (non modular ) bricks of class designation 7.5 plinth level upto floor V level:

6.12.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand ) sqm 139.71 476.85 66619.76

Extra for additional height in centring, shuttering wherever required with adequate bracing, propping etc. including cost of

5.11 deshuttering and decentring at all levels over a height 3.5 m for every additional height 1 metre or part there of ( Plan area to be

5.11.1 Suspended floors, roofs, landing, beams and balconies ( Plan area to be measured ) sqm 138.21 121.65 16813.00

AMOUNT A 13369999.96

RAIN WATER HARVESTING

NS Designing and Constructing of percolation pit cum perforated well 3000mm. dia upto 4000 mm deep, 230 mm thick brick masonry

work alround upto 1.5 m deep with 75 class brick in cement mortar 1:4, 200 mm foundation concrete in 1:4:8 mix below brick work

1 only, 150 mm thick precast removable RCC top slab with required steel reinforcement in cement concrete 1:2:4 mix, filled with Each 2.00 85077.6699 170155.34

coarse aggregate, SFRC covers, river pebbles of requisite size stone as shown in the drawing including centering and shuttering, as

shown complete as per detailed drawings complete.

24.1 Boring/drilling bore well of required dia for casing/Strainer pipe,by suitable method prescribed in IS:2800 (part-samples from

2 different stata, preparing and submitting strata chart1),including collecting bore log,including hire & running charges of all

eqquippments, tools,plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre

depth below ground level.

24.1.1 All types of soil

24.1.2 Rocky strata including Boulders

Supplying,assemnbling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well screen (RMS) pipes

3 24.4 with ribs, Conforning to Is:12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per

direction of Engineer-in-charge.

24.4.3 200 mm nominal size dia metre 120.00 981.7 117804.00

Constructing bar screen / settling tank, of sizes 4500x2500 with suitable depth up to 2.0 m in 1: 4 Cement Mortar (one cement : 4

coarse sand) height as per site requirement, in brick masonry 350mm thick walls upto water level and 230mm thick walls above

water level & upto ground level, including all excavation, 20 cm thick bed concrete in 1:4:8 (one cement 4 fine sand 8 stone

aggregate 40 mm), cement plaster 1:3 (one cement :3 coarse sand) with a floating coat of neat cement as inside finish , top slab in

4 RCC 1:2:4, including centring, shuttering and steel work, also providing and fixing D.I. manhole cover & frame of size 605mm x Each 2.00 74261.32686 148522.65

450mm of weight not less than 38 kg (frame + cover) and cost of 100mm dia C.I. vent pipe with C.I. Ventilating Cowl and suitable

wire mesh provision for inlet, 115mm baffle walls extending 2/3 the width spaced@500mm c/c including finishing with 1:3 cement

plaster 15mm thick with floating coat of neat cement slurry , all complete in every respect as per drawing and as directed to suit site

AMOUNT B 552422.99

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

PLUMBING & PHE WORK

A SANITARY FIXTURE:

Providing and fixing water closet squatting pan (Indian type WC pan) with 100mm sand cast iron P or S trap, 10 litres low level

1 17.1 white PVC flushing cistern with manually controlled device (Handle lever) conforming to IS:7231 with all fittings & fixtures

complete including cutting and making good the walls and floors wherever required.

17.1.1 White Vitreous china Orissa pattern WC pan of size 580 x 440mm with integral type foot rest. Each 12.00 2964.10 35569.20

Providing and fixing white vitreous china pedestal type water closet (European type W.C pan) with seat & lid, 10 ltr low level

2 17.2 white PVC flushing cistern manually controlled device (handle liver), coforming to IS:7231, with all fittings and fixtures complete

including cutting & making good the walls and floors wherever required.

17.2.1 WC Pan with ISI marked white plastic seat and lid. Each 5.00 2885.10 14425.50

Providing and fixing white vitreous chine flat back type lipped front urinal basin 430x260x350mm size with automatic flushing

3 17.4 cistern with standard flush pipe and CP brass spereaders with brass unions and GI clamps complete including painting of fittings

brackets, cutting & making good the walls and floors wherever required

17.4.3 Range of three urinal basins with 10 ltrs. White PVC automatic flushing cistern Each 3.00 6229.90 18689.70

Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including

painting of fittings and brackets cutting & making good the walls, wherever required

17.7.1 White vitrious china wash basin size 630 x 450mm with a pair of 15mm C.P. brass pillar taps Each 13.00 1848.35 24028.55

5 17.28 Providing & fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete.

17.28.1 Semi rigid pipe

6 17.29 Providing & fixing 100 mm sand cast iron grating for gully trap Each 10.00 24.60 246.00

Providing and fixing 600 x 450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard

board ground fixed to wooden cleats with CP brass screws and washers complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50cm deep and 1.8cm thick, fixed in

8 8.1 urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout

or with cement concrete 1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregte 6mm nominal size) aas per direction of Engineer-in-

chare and finished smooth

8.10.1 White Agria Marble Stone sqm 1.13 2670.75 3004.59

(B) SOIL WASTE VENT PIPES AND FITTINGS:

9 17.35 Providing and fixing soil, waste vent pipes

17.35.1.2 Centrifugally cast (spun) iron socketed pipe as per IS:3989.S&S pipe Mtr 88.00 857.30 75442.40

17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS:3989. Mtr 100.00 744.50 74450.00

Providing and fixing MS holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including

10 17.37 cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including

cost of cutting holes and making good the walls etc.

11 17.38 Providing and fixing bend of required degree with access door insertion rubber washer 3mm thick bolts and nuts complete

17.38.1.2 Sand Cast iron S&S as per IS-3989 Each 10.00 353.25 3532.50

17.38.2.2 Sand Cast iron S&S as per IS-3989 Each 8.00 281.15 2249.20

12 17.39 Providing and fixing plain bend of required degree

17.39.1.2 Sand Cast iron S&S as per IS-3989 Each 23.00 296.35 6816.05

17.39.2.2 Sand Cast iron S&S as per IS-3989 Each 28.00 221.95 6214.60

13 17.57 Providing and fixing collars

17.57.1.2 Sand Cast iron S&S as per IS-3989 Each 44.00 238.25 10483.00

17.57.2.2 Sand Cast iron S&S as per IS-3989 Each 50.00 169.65 8482.50

14 17.58 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes & fittings of dia

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

15 17.59 Providing and fixing MS stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter.

Providing and fixing trap of self cleaning design with screwed down or hinged grating with or without vent arm complete,

including cost of cutting and making good the walls and floors.

a) 17.60.2 a) 100mm inlet and 75mm outlet

17.60.2.2 Sand Cast iron S&S as per IS-3989 Each 34.00 838.85 28520.90

Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate

grey or buff etc. over a coat of primer (of approved quality) for new work.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with

18 17.71 bracket of the same meterials with snap fitting of approved quality colour and make, weighing not less than 105 gms. Each 13.00 180.10 2341.30

Providing and fixing water Jet spray with hose pipe and CP brass angle valve to be fitted with seat cover of european water closet

complete in all respect of approved quality

C) WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including

19 18.7 all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.3 25 mm nominal outer dia Pipes Mtrs 38.00 197.9 7520.20

18.7.4 32 mm nominal outer dia Pipes Mtrs 42.00 252.65 10611.30

18.7.5 40 mm nominal outer dia Pipes Mtrs 40.00 348.25 13930.00

18.7.6 50 mm nominal outer dia Pipes Mtrs 20.00 514.35 10287.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes

& fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints

complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

18.8.1 15 mm nominal outer dia Pipes Mtrs 34.00 218.65 7434.10

18.8.2 20 mm nominal outer dia Pipes Mtrs 32.00 243.05 7777.60

18.8.3 25 mm nominal outer dia Pipes Mtrs 29.00 297.95 8640.55

18.8.4 32 mm nominal outer dia Pipes Mtrs 19.00 358.9 6819.10

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including

21 18.9 all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching

,refilling & testing of joints complete as per direction of Engineer in Charge.

External works:

18.9.3 25 mm nominal outer dia Pipes Mtrs 30.00 185.15 5554.50

18.9.4 32 mm nominal outer dia Pipes Mtrs 25.00 230.45 5761.25

18.9.5 40 mm nominal outer dia Pipes Mtrs 36.00 309.6 11145.60

18.9.6 50 mm nominal outer dia Pipes Mtrs 30.00 475.7 14271.00

Making connection of GI distribution branch with GI main of following sizes by providing & fixing tee, including cutting and

threading the pipe etc. complete.

23 18.17 Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end).

18.17.1 25mm nominal bore Each 4.00 372.95 1491.80

18.17.2 32mm nominal bore Each 4.00 450.9 1803.60

18.17.3 40mm nominal bore Each 3.00 546.05 1638.15

18.17.4 50mm nominal bore Each 3.00 780.6 2341.80

24 18.18 Providing and fixing ball valve (brass) of approved quallity. High or low pressure, with plastic floats complete.

a) 18.18.3 a) 25mm nominal bore Each 3.00 421.65 1264.95

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

25 18.19 Providing and fixing gun metal non-return valve of approved quality (screwed end).

18.19.4 50mm nominal bore

26 18.21 Providing & fixing unplasticised PVC connection pipe with brass unions:

18.21.1 30cm length

18.21.1.1 15mm nominal bore Each 13.00 51.35 667.55

27 18.22 Providing & fixing C.P. brass shower rose with 15 or 20mm inlet:

28 18.41 Providing & fitting sand of grading zone V or coarser grade alround the GI pipes in external work:

18.41.6 50mm diameter pipe Mtr 1.00 61.4 61.40

29 18.49 Providing & fixing CP brass bib cock of approved quality conforming IS 8931:

18.49.1 15mm nominal bore Each 31.00 397.5 12322.50

30 18.52 Providing and fixing CP brass stop cock (concealed) of standard design and approved make confirming to IS: 8931.

31 18.53 Providing and fixing CP brass angle valve for basin mixer and gyser points of approved quality confirming IS: 8931:

18.53.1 15mm nominal bore Each 13.00 449.35 5841.55

Providing and placing on terrace (at all floor levels) polythene water storage tank of approved brand and manufacture with cover

32 18.48 and suitable locking arrangement and making necessary holes for inlet , outlet and overflow pipes but without fittings and the base

support for tank.

Making khurras 45x45cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone

33 12.22 aggregate of 20 mm nominal size ) over PVC sheet 1 m X1M X400 micron finished with 12 mm cement plaster 1:3 (1 cement :3 each 12.00 148.75 1785.00

coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with

seal ring conforming to IS 5382 leaving 10 mm gap for thermal expansion i) single socketed pipe.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised -PVC rain water pipes by means of 50

35 12.43 X50X50 mm hard wood plugs ,screwed witjh MS screws of required length including cutting brick work and fixing in cement

morter 1:4 (1 cement :4 coarse sand) and making good the walls etc. complete.

Providing and fixing 15mm C.P brass mixing fitting (C.P. wall mixer Tel. type) for Bath with C.P. bend/Crutch complete. Including

cutting and making good the walls wherever required .C.P. brass mixing fitting.

D) SEWERAGE (INTERNAL):

Providing, laying & jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1

cement : 1 fine sand) including testing of joints etc. complete

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) alround SW

pipes including bed concrete as per standard design.

Providing and fixing square - mouth SW gully trap grade 'A' complete with CI grating brick masonry chamber with water tight CI

38 19.4 Cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50 Kg) and frame to be not less than 2.70 Kg

as per standard design.

a) 19.4.1 100x100mm size 'P' type

19.4.1.1 With FPS bricks class designation 7.5 Each 10.00 1256.35 12563.50

Constructing brick masonary manhole in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement: 2

coarse sand: 4 graded stone aggregate 20 mm nominal size), fondation concrete 1:4:8 (1 cement: 4 coarse sand: 8 graded stone

39.00 19.7 aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with

floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregated 20

mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Inside size 90 x 80 cm and45cm deep including CI cover with frame (light duty ) 455 x 610 mm internal dimensions total weight of

cover and frame to be not less than 38 kg) (weight of the cover 23 kg and weight of frame 15 kg).

19.7.1.1 With FPS bricks with class designation 75 Each 12.00 7132.00 85584.00

40 19.8.1 Extra for depth of manhole

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

With FPS bricks with class designation 75 Each 7.00 4061.70 28431.90

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS:10910 on 12mm dia steel bar

comforming to IS:1786 having minimum cross section as 23mm x 25mm and over all minimum length 263 mm and width as

165mm with minimum 112mm space between protruded legs having 2mm tread on top surface by ribbing or chequiring besides

41 19.16 necessary & adequate anchoring projections on tail length on 138mm as per standard drawing and suitabbe to with stend the bend Each 23.33 256.75 5990.83

test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even

after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone

aggregate 20mm nominal size) complete as per design.

E) EARTH WORK( INTERNAL PLUMBING WORK)

Earth work in excation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30cm in depth, 1.5 in

42 2.6 width as well as 10 sq.mt in plan) including disposal of excavated earth lead upto 50m and lift upto 1.5 m disposed earth to be

levelled and neatly dressed.

Excavating trenches of required width for pipes, cables, etc. including excavation for sockets and refessing of sides, ramming of

43 2.10 bottom depth upto 1.5m including getting out the excavated soil, and then returning the soil as required in layers not exceeding

20mm in depth including consolidating earth deposited layer by ramming, watering etc. and disposing of surplus excavated soil as

directed within a lead of 50m.

a) 2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm dia Mtr 103.00 101.40 10444.20

Filling available excavted earth (excluding rock) in trenches, plinth sides of foundations etc. in layet not exceeding 20 cm in depth

consolidation earth deposited layer by ramming and watering lead upto 50m and lift upto 1.5m

AMOUNT C 952151.04

ELECTRICAL WORK

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core

1.1 1.10 cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point

with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

a. 1.10.3 Group C (FULL RATE QTY ) Point 343.00 664.00 227752.00

1.10.3 Group C (PART RATE QTY ) Point 54.00 265.60 14342.40

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed

1.2 1.11 medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC Point 24.00 710.00 17040.00

insulated copper conductor single core cable etc as required.

Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated, copper conductor, single core cable in surface/recessed PVC

conduit alongwith 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/power plug with 4x4 Sq.mm FR PVC insulated, copper conductor, single core cable in surface/recessed PVC

conduit alongwith 2 Nos. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as required

b) 1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 200.00 206.00 41200.00

c) 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire Metre 100.00 358.00 35800.00

Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the

existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned

copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the

wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but

excluding modular plate etc. as required.

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

a. 1.24.6 Telephone socket outlet Each 8.00 89.00 712.00

b. 1.24.7 TV antenna socket outlet Each 2.00 93.00 186.00

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but

excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and

1.13 1.31 fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used Each 2.00 288.00 576.00

in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and

fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Erection of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all

accessories including connection etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all

1.17 1.41 accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single Each 141.00 69.50 9799.50

core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.

1.18 1.45 mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the Each 85.00 99.00 8415.00

fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as

1.20 1.51 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. Each 16.00 68.50 1096.00

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top

1.21 2.18 alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out Each 8.00 693.00 5544.00

let and complete with connections, testing and commissioning etc. as required.

Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry

including bending the pipe to the required shape complete as required.

2 MCCB, MCB & DB's

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in

cubicle panel, making connections, etc. as required.

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess

2.2 2.8 complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC

insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate,

interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator)

Supplying and fixing following way prewired vertical type TP&N MCB distribution board of steel sheet for 415 volts on surface/

recess complete with loose wire box of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus

2.3 2.9 bar, common neutral link, earth bar, din bar for mounting MCB's, terminal connectors for all incoming and outgoing circuits, duly

prewired with adequate size of FR PVC insulated copper conductor upto the terminal connector/ neutral link, earthing etc as

required (But without MCB/ RCCB/ Isolator). (Note : Prewired vertical type MCB TPDB is normally used where 3 phase outlets

a. 2.9.7 8 way Double door Each 1.00 9606.00 9606.00

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB),

2.6 2.15 having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning

etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/

3.2 5.9 terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt Metre 41.00 97.50 3997.50

& spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode

including connection with G.I. thimble excavation and re-filling as required.

4 FITTING AND FIXTURES

Supplying installation testing and commissioning of following luminaries mounted on surface/ recess required for internal wiring

of the building along with suitable hangers and lamps.

18W LED Box Type Fitting Surface mounted as per Osram Product. No LUXLINE LED BATTEN 18W 765 10x1 IN or similar

specification of other approved makes.

8W LED Fitting Bulk Head Site as per Philips Product. No WT202W LED6S CW PSU S1 PC or similar specification of other

approved makes.

10W LED Fitting Surface mounted down lighter as per Osram Product. No LEDCOMFO CEILING 10W 6000K 4x1 APAC or similar

specification of other approved makes.

12W LED Fitting Surface mounted down lighter as per Osram Product. No PLATFORMA LED 12W13101/6500K 4x1 APAC or

similar specification of other approved makes.

20W LED Mirror Light Fitting Wall mounted as per Philips Product. No Ecomoods Wall light (16926, antracit) with 20W E27 LED

Osram Lamp or similar specification of other approved makes.

Supply, installation, testing & commissioning of Philips Cat. No. SPP335 1xSONT-150W GB Complete 150W Sodium Lamp Street

4.1 NS light fitting or similar specifications of other approved make with all accessories pole fixing clamps & fixture fixing clamps Each 2.00 10270.23 20540.45

complete as required.

Supplying of approved make ceiling fan of double ball bearing of the following sizes and its all accessories suitable for operation on

230V single phase, 50 Hz, AC supply complete as required.

Supplying of approved make Exhaust Fan of the following sizes and its all accessories suitable for operation on 230V single phase,

50 Hz, AC supply complete as required.

Supplying installation, testing commissioning of telephone tag block or similar specification of other approved makes. of the

following sizes

Supplying & fixing of following capacity TP&N MCB inside the existing panel board with drilling holes in cubicle panel, making

connections, etc. as required.

5 FIRE SUPRESSION SYSTEM

Supply of ISI marked (IS:2878) Squeeze Grip carbon-di-oxide gas type fire extinguisher with cylinder of 4.5 kg. capacity complete

with suitable length hose and horn duly charged and ready for use GI bracket for wall mounting etc. as required.

Supply of ISI marked (IS:13849) ABC dry powder 6 kg. fire extinguisher with cylinder fully charged complete with bakelite horn

discharge tube, GI bracket for wall mounting etc. as required.

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing of 2W LED based Exit Sign Board (Bajaj BHEX 20 R AC or other makes of similar specification) as complete

AMOUNT D 2178747.83

ON-GRID INTRACTIVE SPV POWER PLANT:

Supplying, installing, testing and commissioning of 16kWp On-Grid Intractive SPV power plant on the roof top details specification

The brief specification of above system shall be under :-

SPV Array consisting of PM 160 Modules of CEL make connected in series parallel confirmation to generate minimum 16 kWp

b) Power conditioning unit consisting of MPPT and Inverter 16 KVA (3 Phase). No 1.00

c) Wires, cables and other items Set 1.00

d) Annual Maintenance Charges (AMC) (Three years AMC after completion of Two years warranty) 1.00 137932.85 137932.85

AMOUNT E 1501919.90

Digitally signed by

NBCC PRIYA PRIYACONTRACTOR

KUMARI 20:49:12 IST