MINOR REPAIR OF E/M NATURE INCLUDING INTERNAL ELECTRIFICATION WIRING AT COD CHHEOKI UNDER GE WEST PRAYAGRAJ.

Amount

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing caping/conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade surface conduit with all fixing accessories of 20mm dia, using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed surfaces complete all as specified and directed for the following :- Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface.

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amps on independent board

One point for socket outlet 5 amp same board

One light point controlled by two 2 - way switch

One bell/ buzzer point controlled by one push button on the same board with other switches or independent

One 3 pin socket outlet 15 amps, independent, with cables 2.5 sq. mm size on independent board.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) along with same size and type of wire as continuous earth wire connected to common earth dolly drawn in and including non metallic PVC casing and caping not less than 20mm wide med grade ISI marked complete with all fixing accessories including factory made pressed steel concealed terminal box of required size of 1.2mm thick duly painted with 3mm thick plastic laminated sheet top cover with brass screw and cup washers complete all as specified and directed for the following :- . Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface.

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amps on independent board

One point for socket outlet 5 amp same board

One light point controlled by two 2 - way switch

One bell/ buzzer point controlled by one push button on the same board with other switches or independent

One 3 pin socket outlet 15 amps, independent, with cables 2.5 sq. mm size on independent board.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade concealed conduit with all fixing accessories of 20mm dia, using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed conceal surfaces complete all as specified and directed for the following :- Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface.

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amps on independent board

One point for socket outlet 5 amp same board

One light point controlled by two 2 - way switch

One bell/ buzzer point controlled by one push button on the same board with other switches or independent

One 3 pin socket outlet 15 amps, independent, with cables 2.5 sq. mm size on independent board.

S&F in repair ceiling rose surface type bakelite 65x50mm three terminal complete all as specified and directed.

S&F angle/batten type holder insulated body with back plate suitable for light point complete all as specified and directed.

S&F switch piano flush type, 5 amps, 230V AC,single pole, one way complete all as specified & directed.

S&F socket out let 2-in-1, 3 pin, 5 amp flush type complete all as specified & directed.

S&F switch piano flush type 16 amps, 230V AC single pole one way complete all as specified & directed.

S&F socket out let 2-in-1, 3 pin, 5 & 15 amp flush type complete all as specified & directed.

S&F fan regulator, 5 stepped, electronic type, single phase, 80 watt, socket size incl connection complete all as specified & directed.

S&F bell push piano flush type 5 amp, SP , 230V AC complete all as specified & directed.

S&F 2 way piano flush type 15 amp, SP , 230V AC complete all as specified & directed.

S&F call bell, ding dong type, AC, 230 V, single pole complete all as specified & directed.

S&F in repair switch modular flush type 10 amps, single pole, one way 230 volt complete all as specified & directed.

S&F in repair socket modular flush type suitable for 10 amp, 5 pin ,230 volt complete all as specified & directed.

S&F in repair switch modular flush type 20 amps, single pole, one way ,230 volt complete all as specified & directed.

S&F in repair socket modular flush type suitable for 20 amp, 6 pin ,230 volt complete all as specified & directed.

S&F in repair fan regulator, modular type, 5 stepped, electronic type, single phase 230 volt including connection complete all as specified & directed.

S&F in repair bell push modular flush type 6 amp 230 volt complete all as specified & directed.

S&F in repair 2 way modular flush type Switch, 6 amp 230 volt complete all as specified & directed.

S&F in replacement of sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug and socket along with one MCB, single pole of current rating 20 amps, C series 240 volts AC complete all as specified & directed.

S&F in replacement of Modular single pole and neutral enclosure with modular socket along with one MCB, single pole of current rating 20 amps, C series 240 volts AC complete all as specified & directed.

Taking down main switches fuse unit, MCB/Kit kat distribution board with steel enclosure along with MCB’s /Kit kat fuse of any amps/ways including wooden board or from steel board and making good disturbed surfaces complete all as specified & directed.

S&F sheet metal enclosure for MCB's 240 volt 4 way single pole and neutral with 200 amps rated busbar double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F sheet metal enclosure for MCB's 240 volt 6 way single pole and neutral with 200 amps rated busbar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with 200 amps rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole & Neutral, 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole & neutral 40/63 amp, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F in repair MCB triple pole & neutral 25 to 63 amp, 415 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

Taking down carefully sub main wiring of any nos of wire and size with earth wire on wooden batten/surface conduit/casing caping complete with its all accessories complete all as specified & directed.

M&L for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of size 2.5 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories alongwith one run of PVC insulated unsheathed stranded copper conductor of size 1.5 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M&L for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of size 4.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories alongwith one run of PVC insulated unsheathed stranded copper conductor of size 2.5 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M&L for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of size 6.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories alongwith one run of PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M&L for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of size 10.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories alongwith one run of PVC insulated unsheathed stranded copper conductor of size 6.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

Supply & fixing in replacement of worn out/rusted sunken box of size 100 mm X 100 mm with pressed MS/GI steel terminal boxes of depth not less than 50 mm, flush type of thickness lot less than 1.22 mm of following size alongwith new 3.0 mm thick plastic laminated sheet cover of suitable size including cutting/drilling hole and fixing switches, sockets, fan regulator etc as removed from old sheet and fitted with cadmium plated screw washer and making good to disturbed surface with cement mortar complete in all respect as specified and directed.

Supply & fixing in replacement of worn out/rusted sunken box of size 175 mm X 100 mm with pressed MS/GI steel terminal boxes of depth not less than 50 mm, flush type of thickness lot less than 1.22 mm of following size alongwith new 3.0 mm thick plastic laminated sheet cover of suitable size including cutting/drilling hole and fixing switches, sockets, fan regulator etc as removed from old sheet and fitted with cadmium plated screw washer and making good to disturbed surface with cement mortar complete in all respect as specified and directed.

Supply & fixing in replacement of worn out/rusted sunken box of size 200 mm X 150 mm with pressed MS/GI steel terminal boxes of depth not less than 50 mm, flush type of thickness lot less than 1.22 mm of following size alongwith new 3.0 mm thick plastic laminated sheet cover of suitable size including cutting/drilling hole and fixing switches, sockets, fan regulator etc as removed from old sheet and fitted with cadmium plated screw washer and making good to disturbed surface with cement mortar complete in all respect as specified and directed.

Supply & fixing in replacement of worn out/rusted sunken box of size 250 mm X 200 mm with pressed MS/GI steel terminal boxes of depth not less than 50 mm, flush type of thickness lot less than 1.22 mm of following size alongwith new 3.0 mm thick plastic laminated sheet cover of suitable size including cutting/drilling hole and fixing switches, sockets, fan regulator etc as removed from old sheet and fitted with cadmium plated screw washer and making good to disturbed surface with cement mortar complete in all respect as specified and directed.

Taking down existing old /worn out tube/CFL/bulk head/sketch light fittings of indoor type fixed on wall of any type/size with its all accessories including lamp complete all as specified & directed

Supply & fixing surface /wall mounted light fitting in CRCA powder coated white housing with pre wired suitable for single T8 LED tube along with supply and fixing one number LED tube in polycarbonate housing of nominal wattage - 18 Watt, Lumen output - 2100 Lm, Colour Temp - 6500 Kelvin, Size & Length - G13/ T8/ 4 Feet with integral/in built driver, having short circuit and surge protection including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed. Cat Part No for batten:- REGALBATTENT8UPTO1X18WDSBSWH of make Havells 'or' IGP161LT8-16 of make Crompton 'or' TMC501 P 1xT-LED 22W P3241 of make Philips or its equivalent as approved Cat Part No for Tube light:- PHOTANULTRA2.01213T8SSTL18WLED865SPC of make Havells 'or' LTT8-20 of make Crompton 'or' MAS LED tube 1200MM 18W865 T8 I-2100 lm of make Philips or its equivalent as approved

Supply & fixing energy efficient LED light of 10 Watt of length - 02 Feet long having minimum 1150 Lumen output, wide voltage protection range 140-270 Volt AC housed in extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed. Cat part No: -LUMILINEPLUSSBS10WLED865SPCSS of make Havells 'or' BN 021 LED10S- 6500 PSU GR S1 of make Philips 'or' LDL-10-WW of make Crompton or its equivalent as approved

S&F LED light fitting 10 Watt bulkhead luminaries in high pressure die cast aluminium housing, lumen out put - 700 Lm, colour Temp - 6500 K having Ingress protection - IP 65 fpr dust, water & IK 08 for external impact including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Cat Part No - WT140 LED7S NW PSU S1 PC; Vistaglow of make - Philips 'or' LBHP-10-CDL of make Crompton 'or' LW07-11-XXX-57-XX of make Wipro or its equivalent as approved

S&F in replacement of worn out/old linear fluorescent tube of 36 watt with energy efficient/saving retrofit LED tube in polycarbonate housing of nominal wattage - 18/20 Watt, Lumen output - 2100 Lm or above, Colour Temp - 6500 Kelvin, Size & Length - G13/T8/4 Feet, Operating Voltage - 230 Volt AC, THD ≤ 20 % with integral/in built driver, having short circuit and surge protection upto 4 KV and other safety test as per IS 15885 Part 2/Sec 13 including making minor addition/alteration in existing circuit as required complete all as specified and directed. Cat Part No:- PHOTANULTRA2.01213T8SSTL18WLED865SPC make of Havells or its equivalent in Philips/Crompton or as approved. Cat Part No for Tube light:- PHOTANULTRA2.01213T8SSTL18WLED865SPC of make Havells 'or' LTT8-20 of make Crompton 'or' Essential LED tube 1200MM 20W865 T8 I-2100 lm of make Philips or its equivalent as approved

Supply & fixing in replacement of worn out 36 watt FPL with retro fit linear LED PLL lamp with extruded plastic body and PC diffuser complete with inbuilt electronic driver of high efficacy of system wattage 18 Watt, Length - 419 mm, Lumen output - 1800 Lm or above, Colour Temp - 6500 K suitable for installation in existing 2G11 lamp holders including minor alteration in existing circuit as required complete all as specified and directed. Cat Part No:- PHOTONULTRAPLL419TL18LED865SPC of make Havells 'or' LED PL-L 18W,6500K 2G11 of make Philips 'or' LL18-181-65PL1 of make Crompton or equivalent as approved

S&F in replacement of Decorative wall mounting fixture with elegant diffuser, Floral blown glass, Metal of holder base, ambience E27, 1x8W, along with LED lamp 8 watt ,complete in specified and as directed. Make : Philips Model No. 37934/06 or equivalent in Havells/Crompton Greaves.

S&F in replacement of existing worn out ceiling light with environmental friendly, new generation, aesthetically designed, ultra modern recessed mounted LED light luminaries of size 595 mm x 595 mm an independent Isolated, electronic LED driver (SMPS based constant current supply) housed in CRCA powder coated sheet of system wattage - 36/40/42 Watt, Lumen out put- 4000-4300 Lm, THD < 10%, PF > 0.9, having short circuit and surge protection suitable for Armstrong/ Grid ceiling with all connected accessories including making connection with three core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed. Cat pt No: PLUTONEO2X2PLR42WLED857S of make Havells 'or' RC380B LED36S-4000 G4 L60 W60 PSD OD WH OC of make Philips 'or' LCTTLRP-36-FO-CDL of make Crompton or its equivalent as approved.

S&F in replacement of existing worn out spot light 6 watt of 138 mm dia with Recess mounted pressure die-cast aluminium luminaries in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver complete with LEDs, in built electronic LED driver and accessories pre-wired up to terminal block including making connection complete all as specified and directed. Cat pt No: EDGEPRODDLR6WLED840S of make Havells 'or' DN191B LED6S-4000 PSU WH S2 of make Philips 'or' CDR -204-06-57-SL-NWH of make Crompton or its equivalent as approved.

S&F in replacement of existing worn out spot light 12 watt of 90 mm dia with Recess mounted pressure die-cast aluminium luminaries in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver complete with LEDs, in built electronic LED driver and accessories pre-wired up to terminal block including making connection complete all as specified and directed. Cat pt No: EDGEPRODDLR12WLED840S of make Havells 'or' DN191B LED12S-4000 PSU WH S2 of make Philips 'or' CDR -204-12-57-SL-NWH of make Crompton or its equivalent as approved.

S&F in replacement of existing worn out spot light 15 watt of 155mm dia with Recess mounted pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver complete with LEDs, in built electronic LED driver and accessories pre-wired up to terminal block including making connection complete all as specified and directed. Cat pt No: EDGEPRODDLR15WLED840S of make Havells 'or' DN191B LED15S-4000 PSU WH S2 of make Philips 'or' CDR -204-15-57-SL-NWH of make Crompton or its equivalent as approved.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover reinforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified and directed.

S&F DB-VTPN DB 8 way, 250 A MCCB Double door DB's As per IEC 61439-3, Suitable for Flush Mounting and Surface Mounting, With 250 A Copper Busbar for each phase, With 2 Neutral bar, 2 Earth bar and Cable ties for Cable management, Fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP 43 & IP 54 dB's, with provision for MCCB 160 Amp as incomer complete all as specified and as directed.

Schedule of Credit (MINUS) Rs. 158044.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. ] This amount shall be automatically deducted to arrive at tendered sum

M/s A.K Construction (BID ID -3079105)

Aawadh associates (BID ID -3063425)