Interior fit out work at the office space of IRCTC at 2nd, 3rd and 4th floors of Tower D, World Trade Centre, Nauroji Nagar, New Delhi

Grand Total DSR + Non DSR (Including of

Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and

shuttering-all work upto plinth level.

1.2 4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) cum 300 ₹ 6,812.00 ₹ 2,043,600.00

REINFORCED CEMENT CONCRETE WORK TOTAL ₹ 2,043,600.00 ₹ -

2 SUB HEAD-II :- MASONRY WORK

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC

blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with

approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge.

(The payment of RCC band and reinforcement shall be made for seperately).

CORE CUTTING :Performing Core cutting in RCC Slab of Max 200 MM Thickness and up to 10" diameter &

2.2 NSR rectangular cut out slab / beam. The cost to include covering the joints with silicon sealant to check water Each 7 ₹ 5,000.00 ₹ 35,000.00

PORTLAND CEMENT THIN SCREED FLOORING :P & L 1:4 Nominal mix (1 cement & 4 Screeding Sand)

neat cement flooring of up to 8 mm Thickness. The surface shall be spread evenly & levelled carefully. Low

places shall be filled, humps removed & the whole surface again levelled . Tolerance: ± 5mm

Quoted rate to include lead, lift at all level , pumping, placing, necessary formwork, cost of covering the

finished concrete surface with 200micron thick polythene sheet & curing etc. complete. Self levelling is

included in this rate.

MASONRY WORK TOTAL ₹ 122,504.66 ₹ 262,500.00

3 SUB HEAD-III :- PAINTING AND FINISHING WORK

3.1 13.1 12mm cement plaster of mix :

POP PUNNING WORKS: Providing & applying average 12mm thick plaster of Paris and wire mesh at joints

of diff material to the wall and columns in square plumb line and level including scraping and removing the

existing neeru finish, hacking the surface of wall /columns. After levelling, the surfaces to be finished to

receive paint etc. Rate to include providing for Al channel and grooves at all junctions and corners.

GYPSUM PLASTER : Providing and laying up to 12 mm thick gypsum plaster confirming to Testing

Standards Confirms to IS 2542 (Part I)-1964 for physical characteristics Confirms to IS 2547(Part I & II)-1976

for chemical characteristics to all types of Block masonry work/ RCC surfaces including wall, jambs and Cill &

3.3 NSR Slabs etc.at all level , locations in line, level & finished to receive paint. Rate to include providing for sqm 250 ₹ 350.00 ₹ 87,500.00

Aluminium channel and grooves at all junctions and corners.Rates shall include the fibre glass mesh on

complete surface and also junction/ corners of two material meet ( column to wall, wall to beam, lintel to

beam, corners of wall /columns etc complete ) .

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound )

3.4 13.83 content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats

wherever required to achieve even shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic

Compound ) content.

13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre sqm 6600 ₹ 73.95 ₹ 488,070.00

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface

even and smooth complete.

PAINTING AND FINISHING WORK TOTAL ₹ 1,552,364.55 ₹ 192,500.00

4 SUB HEAD-IV :- WOOD AND P. V. C. WORK

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core

4.1 9.21 of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering

with vertical grains or cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm 80 ₹ 2,392.65 ₹ 191,412.00

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish

4.2 9.127 with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046

Type S, including cost of adhesive of approved quality- 1.0 mm Thick

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of

flush door shutters (over all area of door shutter to be measured).

Providing & Fixing of Modular Aluminium single leaf Door framing System duly Anodized Aluminium

4.3 NSR Sections using 100mm x 25mm for Flush Door upto 45mm Thick and all Required accessories like metre 30 ₹ 4,200.00 ₹ 126,000.00

Silicone/Thermoplastic Gaskets & Screw Caps.

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc.

D OFFSET HANDLE 600 HT : Differential Extra cost for D offset pull handle pair of size:

Ø25mm x 600mmas approved by EIC/client ,including all keys and fixing accessories.

INTEGRATED CONCEALED DOOR CLOSER : Differential Extra Cost over and above for Providing

& Fixing Door Closer - Integrated Cam action Door Closer with hold-open slide arm Closing force: 2-4

2V, Tested according to EN 1154 or equivalent IS CODE for door width up to: 1100mmBack check

and latching speed adjustable

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

Polishing in high gloss/matt finish melamine clear polish on wood work in

required color/wooden shade texture with following process in the sequence

as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then

with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying

time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading

with ample water to remove excess sealer layer and make the surface further

smooth after this wet rubbing, then surface is applied with special grade

4.8 13.116 melamine fillers to fill all the small and big holes/grooves etc. Filler coat to Sqm 25 ₹ 3,049.85 76246.25

be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done

this surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using

melamine clear polish and melamine thinner in required proportion. This

1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet

rubbed smooth, which is further allowed to dry for 12 hrs. The final

melamine polish is applied with compressor pressure spray gun using

melamine clear polish and melamine thinner mixed in required proportion

complete as per direction of Engineer-in-Charge. (Final coat to be done in

1 or 2 layers without gap of time.

PARTITIONS & PANELLING

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc

coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal

flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon

plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick

fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre

by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with

suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of

boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the

spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to

avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5mm Each) to

be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws,

including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle

beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per

manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG)

plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board

conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to

IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene

Bags fixed to wall with screw, rawel plug & washers and held and in position by criss

cossing GI wire etc. complete as per directions of Engineer-in-Charge.

SINGLE LEAF ALUMINIUM FRAME & STILE GLASS DOOR WITH OFFSET PULL HANDLE

P/F of Single Glazed Door-Consisting of Single Shutter Anodized aluminium finish in 75x45 / 65 x40 mm as

approved by EIC/client of system on all four sides using in vertical, and in top of the door and on the bottom

of the door for 10 mm thick tempered glass insert with around beading, Door shutter to be fixed , 70mm

EPC with one side key and one side thumb turn, Door closer with hold open, floor mounted door stopper and

side / astragal drop seal for sound barrier. Door Frame made put of horizontal member on top 36x100 /

50X100 mm and both vertical member 36x100mm / 50x100 mm Along door jamb with schlegal door trim

and Hinges for 45mm Door as per manufacturers specification. The door frame should be Compatible to hold

the Single glazed aluminium style door shutter. Cost to Include, offset pull handle of size: Ø25mm x 600mm

with accessories for glass door. Material : SS 304. , stile mortise sash lock ML NSL 92 , 92 mm C/C x 35mm

backset includes strike plate and screws, CYLINDER EPC K35/K35, double cylinder in 70mm length with

3keys and fixing screws in SNP finish. Size upto 1200mmX 2700MM

DOUBLE LEAF ALUMINIUM FRAME & STILE GLASS DOOR WITH OFFSET PULL HANDLE

P/F of Single Glazed Door-Consisting of Double Shutters Anodized aluminium finish in 75x45 / 65 x40 mm

as approved by EIC/Designer of system on all four sides using in vertical, and in top of the door and on the

bottom of the door for 10mm thick tempered glass insert with around beading, Door shutter to be fixed with

Narrow stile , 70mm EPC with one side key and one side thumb turn, Door closer with hold open, floor

mounted door stopper and side / astragal drop seal for sound barrier. Door Frame made put of horizontal

4.12 NSR member on top 36x100 / 50X100 mm and both vertical member 36x100mm / 50x100 mm Along door jamb Each 6 ₹ 84,000.00 ₹ 504,000.00

with schlegal door trim and Hinges for 45mm Door as per manufacturers specification. The door frame

should be Compatible to hold the Single glazed aluminium style door shutter. Cost to Include , offset pull

handle of size: Ø25mm x 600mm with accessories for glass door. Material : SS 304. , Narrow stile mortise

sash lock ML NSL 92 , 92 mm C/C x 35mm backset includes strike plate and screws, CYLINDER EPC

K35/K35, double cylinder in 70mm length with 3keys and fixing screws in SNP finish. Size upto 2000mmX

FIRE RATED DOORS SOLID CORE

Providing and fixing solid core 40mm Thk. 120 min. rated metallic fire door : Supply & installation of approved

make 40mm thick light weight asbestos free fire proof doors of 120 minutes fire rating duly tested for Integrity

& Insulation Criteria confirming to IS: 3614 Part 2 and BS: 476 part 22 at Fire Research Laboratory Central

Building Research Institute Roorkee with standard heating conditions as specified in IS: 3809 - 1979 and BS:

476 part 20 & 22 1987 to achieve the required integrity & insulation (i.e. to restrict the heat radiation,

temperature rise on the non fire side to the maximum of 140 degree Centigrade above the ambient

temperature on the unexposed surface of the shutter) complete in all respect as per detail.

Door Frame: Formed out of 1.6mm thick Galvanized steel

sheet pressed form to double rebate profile of size 100mm x 65mm as per IS277.

Shutter: Formed out of 2 NUMBER. 1.6mm thick Galvanized steel sheet with infill of fire rated Acrylic Sealant

and non-combustible core (Rock wool 96Kg/M³) bonded to both faces of sheet with lock seam joints at stile

edges and internal reinforcement at top, bottom and stile edges for fire rating. Finish : Door frames and

shutter shall be finished with primer coating, stoved zinc phosphate primer (35 micron DFT) and thermosetting

Polyurethane aliphtic grade paint (35 micron DFT) of approved colour. Vision Panel : 1 no. of size 450 mm. x

450mm. Vision panel formed out of 6mm thick Pilkington Pyro shield of 120 minutes fire rated clear wired

glass with metal beading as per detail. Contractor to make provision for fixing of Access Control System

Device where ever required as per detail.

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

Fabricate and install pelmet made off 19 mm Thk BWP Ply or 18 mm Thk Prelam MDF Board as approved by

the EIC, to be mounted with GI/ CPTW studs at every 1100 MM on the Structural Beam or Slab , Rate to

4.14 NSR-4 include finishing exposed surfaces of the Pelmet with enamel paint of approved shade wherever Required. metre 345 ₹ 1,474.00 ₹ 508,530.00

Pelmet to be ready to receive blinds.

External Glazing Pelmet of 150 mm to 250 high and with approx. 400 angled width and in line with external

glazing as per detail of EIC.

CORNER GUARD FOR WALLS: Providing and fixing of Anodised Polished Aluminium/ Textured PVC Corner

Guards as per the as per the colour and Design as approved by EIC/CLIENT of upto 25mm x 25mm in all

exposed Protruding corners. Cost to include fixing on the existing surface with neat structural tape without

gaps and undulations.

HAT SECTION PROFILE FOR WRITING GLASS : Providing and fixing of Anodised Polished Aluminium HAT

Section Wall grooves as per the as per the colour and Design as approved by EIC/Client of upto 10 mm x 8

mm in all exposed edges of Lacquered glass and other finishes, . Cost to include fixing on the existing

surface with neat structural tape without gaps and undulations.

WOOD AND P. V. C. WORK TOTAL ₹ 10,987,647.64 ₹ 8,608,395.00

5 SUB HEAD- V :- CLADDING WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade,

5.1 8.2 colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated

with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and

polishing to edges to give high gloss finish etc. complete at all levels.

8.2.2 Granite stone slab colour black, Cherry/Ruby red

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to

edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width

upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity

5.4 8.5 counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. Each 3 ₹ 978.70 ₹ 2,936.10

including moulding, rubbing and polishing of cut edges etc. complete.

ACRYLIC SOLID SURFACE FOR COUNTER TOP :

Providing and fixing storage of approved height and depth up to 650 mm with Caracas and Shutters/

Shelves / Drawers to be made out of 25 mm thick BWP Ply board as approved by EIC/client with all surfaces

faced with upto 1.25 mm thick laminate and PVC edge Banding as per the selection of the EIC/client. Storage

to Comprise of Adjustable shelves / Drawers with Auto close Telescopic channels of along with Water

Dispenser & Dustbin Compartment provided with 150 mm Dia with SS 304 Swivel Lid and Flap Shutter. Cost

to include Counter Top formed with 25 mm Thk Ply/HDHMR or as per requirement of site dressed with

12mm Thk Acrylic Solid Surface and fascia up to 50 mm height on all visible sides as designed by EIC/client

to make to be flush in level with adjoining surfaces and splash-back up to 100 mm height all laid/fixed with

Adhesive as per the proprietary Acrylic Solid Surface Manufacturer.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by

the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size

5.6 8.31 as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement sqm 125 ₹ 1,267.95 ₹ 158,493.75

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-

5.7 8.26 laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823

marked, including priming coat on unexposed arrangement and screws etc. complete :

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain

lining / cladding with necessary screws, including priming coat on unexposed surface with :

8.28.1 Decorative veneer facings of approved manufacture sqm 35 ₹ 1,946.25 ₹ 68,118.75

High Acoustic Skinning: Providing and Fixing 12.5 mm gypsum board with 6 mm perforations of round

form. The reverse of the board incorporates an acoustic fleece which provides sound absorption

performance. Perforation Size : 6 mm round, Perforation Spacing - approximate 15mm c/c, Perforation Area

5.9 NSR-12 : approximate 10 to 12% with NRC value greater than 0.60. Cleaneo Technology -Active reduction of air sqm 441 ₹ 1,105.00 ₹ 487,305.00

pollutants due to Cleaneo Technology, effectively reduces concentrations of VOC’s like alcohol, aldehydes,

ketones and esters as well as unpleasant odours from e.g. food or cigarette smoke. or equivalent as approved

by EIC/client With 50 mm Rockwool suspended on GI framework.

PLYWOOD SKINNING : P/F Plain 12 mm One Side 2 Hour Fire Rated BWP Plyboard Skin with overall specs

as per item A1 on existing Surfaces as specified by the EIC/client. Cost to Include Wooden Framework for

carrying load of TV and other Point Load Items mounted on the Partitions and Panelling. nothing extra shall

be paid for this. items is complete in all respect for partition work

FRAMED SINGLE GLAZED ALUMINIUM PARTITIONS Supply & Installation of Full Height demountable

Anodised Aluminium Single Glazed Series Straight Partitions systems of Matt anodized finish of 50x25 cross

section and 'T' Section, corner Section & 'I 'between glass to glass joint of proprietary make formed out of the

following components as per the detail drawing / design .

Framing: Proprietary anodized aluminium profile using sections on all four sides for the partition as per

manufacturer specifications from FFL up to 2700 mm.

Glazing: 10mm thick toughened Glass for partition system with joint sealed & non staining double sided tape

for glass to glass joint. All exposed edges of the glass shall be machine polished. Quoted rate shall include

packing/liner for all partitions as floor level. Capping & gaskets shall be of EPDM. (Tolerance in section

dimentions (L/B) = +/- 10 mm)

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

Full Height Single Glazed Curve Partition Providing & Fixing of Modular Single glazed Curve partitioning

frame of 45mm System, Using 45mm x 25mm or as per site as wall starter section, Using 45mm x25m as Top

& bottom channel. Toughened Glass of thickness 10mm to be installed with required accessories ie glass to

glass aluminium I sections, T section & 90 degree sections as per the requirement & Glass packing to adjust

the floor level. Insertion of silicon/Thermoplastic gasket to adhere the glass firm & airtight. Partition Height

Considered is 2400mm

ALUMINIUM SKIRTING

Providing and Fixing up to 100 mm High modular skirting fixed as per detail and EICs instructions. Skirting to

be affixed on to plastered/POP finished wall surface. P/F easy stick type with all aluminium trims and

Aluminium champhered corners as per EIC’s approval.

SKINNING WORKS ON EXISTING PARTITIONS AND PANELLING

General Notes: Designer finishes on Partitions / Panelling/Wal Over the existing Paint/ Gypsum/ MDF

skinning. Cost to be presented over and above the add on Existing Partition Skin as one Side skinning.

The cost shall include the MDF/BWP Ply backing skin as approved by the EIC for the

receiving base as specified in the item.

Providing and fixing Fabric Pane / Proprietary Manufactured Specs As approved by the EIC. On 12 mm thick

5.14 NSR-16 tackable board and finished with stretched Fabric as per EIC’s approval. Including cost of providing grooves sqm 90 ₹ 4,022.00 ₹ 361,980.00

and divisions in pane as per EICs elevations or intermediate grooves to be finished with fabric lining as

specified by EIC.

TOILET MIRROR PANELLING

P/F Mirror on a backing of Hollow Panelling of up to 75 mm depth and formed with 12 mm thick HDHMR

5.15 NSR-17 MDF with provision of light coves and finished with 6mm Mirror of Glass framed in Metal Jamb Frame of PVD sqm 52 ₹ 4,896.00 ₹ 254,592.00

finish of Approved make to be flush in level with adjoining surfaces. Cost to also include suggested adhesive

as per approved make and edge polishing. Cost to also include frosting/de mirroring as per EIC Design.

Providing and fixing Wallpaper on Existing Partition and Panelling finished with Wallpaper Selection as per

EIC’s approval. Wall /Ceiling Base to be prepared by applying coat of cement primer scrapped and

smoothened to plumb level on backing panel of Gypsum/ MDF, intermediate grooves to be finished with Paint.

Including cost of providing grooves and/Wall with divisions in pane as per EICs approval. Cost to also

include Neutral Silicon Adhesive or equivalent manufacturer suggested adhesive. Rate to Include Wastage as

Note : Wallpaper should be high end and

shade, design and colour shall be approved by EIC and wallpaper to be measured and paid for the actual

fixed area only.

LACQUERED GLASS FINISH

Providing and fixing Lacquered Glass on a backing of Existing Partition and Panelling and faced front side

with 6 mm thick MDF and finished with 6mm Lacquered Glass Super White Colour or As Approved by the

EIC to make it flush in level with adjoining surfaces. Cost to also include Neutral Silicon Adhesive or

equivalent manufacturer suggested adhesive as per approved Design make and edge polishing. Item Billing

shall be done on Installed area on site with wastage to be included in the rates.

Providing and fixing factory finished Smart PET acoustic panels in thickness up to 12 mm of 0.5 NRC in

wave and other 3D pattern as per design and embossing as per the instructions of the EIC/client. Cost to

include screen printing work and Provision for making Champhered Edges and Grooves in different cuts like

fishbone etc as per the instruction of the EIC/client. Installation to be done according the Design of the

EIC/client. Shop Drawing of pattern and panel joints to be furnished by contractor for approval of the EIC.

RIBBED WOODEN WALL PANELS

Providing and fixing of Acoustical wooden wall panelling consisting of base frame treated with anti-termite

chemical of factory make in color & formation as approved by EIC. Panels to be installed as per specification.

The Timber melamine effect acoustic wall panels made out of Fire Rated MDF core material. The acoustic

wall panels shall be in size of 128x2440x18mm (Thk). Wall slats to be Perforated having perforation to 25/30

5.19 NSR-21 mm diameter holes, at 32/35 mm c/c at the back face, and front of the panels to have cut with grooves of sqm 75 ₹ 6,317.00 ₹ 473,775.00

3mm at 16mm c/c.The back of timber melamine panels shall be laminated with Soundtex black acoustic

tissue to provide NRC not less than 0.6-0.7. The acoustic timber wall panels shall be with tongue and groove

detailing along the length of panels, with square edges on 2 sides along the width of panels. The wall panels

shall be clipped into aluminium channels and clips Keel and Fastener system at 600mm c.c. Density -800kg

/m3, R.H 70, Fire Rated Euro Class B and C formerly Class 0 and Class 1 BS476 part 6 and 7 respectively

METAL BAFFLE FOR WALLS

Providing and fixing decorative wall system manufactured from pre-painted /powder coated lightweight

aluminium Baffles folded to form 1 to 3 mm Thk blades of 25 mm Width and 100 mm depth with spacing of up

5.20 NSR-28 to 150 mm CC, the choice of colours shall be as selected by the EIC. carrier profiles shall be installed first sqm 75 ₹ 7,292.00 ₹ 546,900.00

and levelled accurately at 1200 mm centres and suspended at maximum 1000 mm centres directly from the

structural soffit or from a primary angle section . Primary grid to be suspended at not more than 1 200 mm

centres M6 threaded rod or approved hangers with suspension height void minimum 150 mm.

Providing and applying PU Finish As approved by the EIC on backing of Existing Partition and Panelling and

faced front side with 6 mm thick HDHMR Board and finished with PU Paint as per EIC’s approval.

Provide for grooves or as required finished/ specified by EIC.

80MM PU FINISHED EDGE BENDING FOR CUBICLES

Providing and applying PU Finish including MDF lining 4mm As approved by the EIC on backing of

5.22 NSR-22A Existing Partition and Panelling and faced front side with 12 mm thick HDHMR Board and finished metre 350 ₹ 578.00 ₹ 202,300.00

with PU Paint as per EIC’s approval.

Provide for grooves or as required finished/ specified by EIC.

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

VERTICAL GARDEN (ARTIFICIAL)

5.23 NSR-23 SITC and artifical vertical garden complete in all respect including framing, board, clipping and design shall be sqm 11 ₹ 6,569.00 ₹ 72,259.00

approved by EIC/CLIENTas per approval.

PREMIUM EMULSION PAINT

Providing and applying high performance Premium Emulsion paint of approved colour to Brick Blockwork &

Partitions, False Ceiling , as per Approval of EIC including ba`se putty, base coat as per manufacturers

recommendations and finishing with 1+2 coats of primer and plastic Emulsion paint of approved colour and

make. Surface coating to be achieved as per manufacturer’s recommendations for coverage of paint with

Texture Density as Approved by EIC.

CLADDING WORK TOTAL ₹ 823,502.40 ₹ 24,794,201.75

6 SUB HEAD- VI :- FLOORING WORK

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with

water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all

colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey

6.1 11.41A cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel,

plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic

6.2 11.48 coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and

finishing complete as per direction of Engineer-in-charge.

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear

portion of the building all complete as per EICural drawings, with 18 mm thick stone slab laid over 20mm

(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry

@ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade

including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-

11.51.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. sqm 145 ₹ 6,603.35 ₹ 957,485.75

Providing and fixing removable raised/false access flooring with system and its components of approved

make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load

bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as

per the EICural drawings, as specified and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness

minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x

3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully

threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto

50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed

to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine

screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm

thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws

ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall

receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the

system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical

conduits and wiring etc. all complete as per the EICural drawings, as specified and as directed by the

Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high

pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an

enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel

Gauges: top 0.6 mm and bottom 0.70mm fused spot welded together (minimum 64 welds in Each dome and

20 welds along Each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and

cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core

mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High

Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness

within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm

without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and

Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the

approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be

printed on the side of the panel to ensure the quality of the product.

11.54.1 300 mm Finished Floor Height (FFH) sqm 80 ₹ 5,623.95 ₹ 449,916.00

ANTISTATIC FLOOR

Provide and install 2 mm thick, flooring grade anti stat and non-conductive laminate flooring on existing/

prepared sub floor. Any minor repair works to be carried out by vendor at no extra cost. Cost is also including

providing protection cover with double layer of polythene sheet till handover.

ENGINEERED WOOD FLOORING

Providing & fixing at least 15+/- 1 mm Thk Engineered Wood Flooring topped fabricated vineer of 3mm

thickness with First grade veneer of make as approved by the EIC with all the trims beadings and accessories

required for the purpose. Installation procedure to be done on horizontal and vertical edges as per the above

a properly finished neat cement surface without any undulations and depressions. All the corner beading,

6.6 NSR Metal transition profile shall be included in the cost and laid on site as per the instruction of the Engineer In sqm 270 ₹ 5,400.00 ₹ 1,458,000.00

charge. Cutting in the floor for Wire terminations should be finished properly and should be included in the

rates. Cost is also including providing protection cover with double layer of polythene sheet till handover. Cost

shall also include moisture barrier underlay of 4mm for the complete laid out area. All base rates shall exclude

the Taxes, cartage and Wastages as per the specs. Quoted item Rates shall include wastages as per the

Installation methodology.

CARPET FLOORING

Providing & Fixing of Flocked textile floor covering of Nylon 6.6 face fiber or equivalent approved make with

100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of

4.3 mm, and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant

and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering

should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8 or equivalent ISO Codes,

Friction Slip Resistance Test EN 14041 Class DS, SANITISED anti-microbial treatment, with resilient

waterproof backing, anti allergic which is certified by British allergy foundation, with ten year replacement

guarantee. The carpet should have permanent static control & should be fixed with powder coated aluminum

angles as per detail.

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

Providing and laying Rugs Broadlooms of minimum 4000 gsm in Hand Tufted to Customised design of

approved size in locations as directed. The cost shall include all adhesive necessary items required for

FLOORING WORK TOTAL ₹ 10,744,490.75 ₹ 3,015,500.00

7 SUB HEAD- VII :- ROOFING / FALSE CEILING WORK

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27

mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x

50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required

length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick

bottom wedge of 80 mm with tapered flanges of 26 mm Each having lips of 10.5 mm, at 450 mm centre to

centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out

7.1 12.45 of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27

mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help

of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at

230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing compound in 3layers covering upto

150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the

Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level,

suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm,

both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size

24x38mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of

size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm

center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25

mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form

grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in

the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures,

smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x

25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with

galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T,

bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all

heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with

a 12.52.1 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically sqm 1566 ₹ 1,902.95 ₹ 2,980,019.70

polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS:

2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48

mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise

Reduction Coefficient) of 0.79,with 50 mm resin bonded glass wool backing.

ACCOUSTIC GYPSUM BOARD PERFORATED CEILING : Providing and Fixing suspended ceiling consisting

of 12.5 mm thick as approved by EIC/Designer plaster board or equivalent as approved by EIC/client With 50

mm Rockwool suspended on GI framework. Perforated Gypsum Ceiling with T Grid System

Providing and fixing Perforated glass fiber reinforced Gypsum board comprises of 12.5 mm gypsum core

of size 600mm x 600mm with a geometric array of 6 mm perforations of round form. The reverse of

the board incorporates an acoustic fleece which provides sound absorption performance. Perforation

Size : 6 mm round, Perforation Spacing - approximate 15mm c/c, Perforation Area : approximate 10 to 12%

with NRC value greator than 0.60. Cleaneo Technology -Active reduction of air polluants due to Cleaneo

Technology, effectively reduces concentrations of VOC’s like alcohol, aldehydes, ketons and esters as well as

unpleasant odours from e.g. food or cigarette smoke

Air purification properties tested according to standard

7.3 NSR The false ceiling surfaces shall be prepared to the satisfaction of the EIC, and shall be applied with two sqm 120 ₹ 3,700.00 ₹ 444,000.00

coats of primer and Paint as per direction of Engineer in charge.

Notes: Two coats of gypboard primer to be applied to finished surfaces and then smoothened using chalk

putty as directed in order to receive the Paint as instructed by the EIC/client.

All junctions between material ,

columns, wall -ceiling etc. to have a 6mm groove with 12 x 12 x 1.2 mm Thk Aluminium `L' angle/shadow

angle as per detail. .

Rate quoted to include vertical drops, Bulkheads , level and Alleys as per the Instruction of the

EIC/client to be paid in the Installed Area. Rate to also include the making of cove and all cut-outs required

for light fixtures, smoke detectors , Up to 250 mm wide return air slits & A/C boxing wherever indicated. and

other services cut-outs complete as directed by EIC/client. Shop Drawing of perforated pattern and joints to be

furnished by contractor for approval of the EIC..

METAL TILE GRID CEILING : P/F Metal Lay-In tile, Micro Look grid structure, 1.5mm dia holes,18% open

7.4 NSR area,Diagonal Pitch. The ceiling tiles Module size of 600x600 in 0.5mm galvanized Powder coated metal sqm 470 ₹ 1,600.00 ₹ 752,000.00

perforated tile and NRC 0.5 or equivalent of size 600 x 600 Module.

TRAP DOORS / AACCESS PANELS

P & F trap doors of n ceiling made of 19 mm thick commercial BWP plywood pane placed inside MS

channel frame work which is fixed to ceiling framing on all sides and hanged from RCC slabs with GI

flats/wires which are fixed with dash fasteners, openable Hinged Door panel to be cladded with 1.00mm thick

approved laminate matching paint with L& Key Lock i/c painting inner side, complete as per design & drawing

& instructions of EICs.

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

PRINTED BACKLIT STRETCH FALSE CEILING :Providing and fixing demountable ceiling made of Polyester

knitted fabric plain or printed in design and pattern as approved by the EIC /designer ,coated with

polyurethane 309 T Translucent white, Weight: From 200g to 250g / m2. Fire Rating:B s1 d0 (Ex M1) / Flame

retardant. Fabric has translucid fabric for backlighting purpose with CE (Complies with European Union

norms), stretch on self supporting frame Profile. The rates should be inclusive of the necessary frame works

for the fixing arrangement and 19 mm thick FR back ply for backing surface & 36 watt chipped module / strip

4000 K of approved make at distance of 6" c/c with ballast complete with trap doors as advised. Warranty: 2

years on driver & 5 years on LED Lighting. Lights to be placed in such a manner that no dark patch appears or

zebra pattern appears. Once lights are installed stretch ceiling to give uniform output with required lux level as

per EIC. Cost to also include printing in colour and design on the membrane as approved by the

EIC/Designer. Cost to include cost 1Metre x 1 Metre mockup with Lights installed for review and approval if

required by the EIC/client and Client prior to fabrication and installation of actual product.

system formed as an open metal ceiling with an open area of more than 50% and to the flare [5mm] of the

perforation pattern [RV-50-40] the ceiling has a three-dimensional visual effect and hides the insight into the

plenum. Bypassing the perforation, the S-shaped sides of the LOOP® interlock both the long and front side

joint with a non magnetic suspension, the elements are installed with a circumferential 1 mm joint, thus

compensating tolerances in x and y direction. The non-magnetic suspension system effectuates a self-

alignment of the elements [puzzle effect]. The module size 966x1115x1.0mm GMS is perforated with 60mm

deep drawn holes .The substructure consists of a form perforated L profile as a lateral grid which is

suspended from the ceiling with nonius adjustable upper and lower parts or with threaded rods using official

approved dowel plugs. The grid profiles are to be connected together at the ends by means of longitudinal

connectors [screw fasteners]. The spacing of the grid profile is according to the requirementsas well as the

loads of the system and to be determined and checked by the contractor. The profiles are attached to the

walls with wall brackets. On profiles angles, C-band raster as secondary profiles are bolted on by means of C

channel hanger bracket with M6 bolts. The longitudinal connections of the C-profiles are made by C profile

connectors. Only construction parts approved by the manufacturer may be used. Provide necessary supports,

provisions as per the EICs / client Instructions. Finish of ceiling is in white/ Silver grey powder coated with

minimum 60 microns paint thickness. Cost to include Edge Trims in profile and shape as per Design of the EIC

OPEN CELL ALUMINIUM POWDER COATED CEILING

Providing and fixing 100mm x 100mm. decorative open cell ceiling system made of simple geometric

construction featuring a slick 10mm. blade width. Installation to be done as per the manufacturers proprietary

Specs according the Ceiling Design of the EIC.

METAL BAFFLE CEILING

Providing and fixing decorative ceiling system manufactured from pre-painted /powder coated lightweight

aluminium Baffles folded to form 1 to 3 mm Thk blades of 25 mm Width and 100 mm Height with spacing of

7.10 NSR-28 up to 150 mm CC, the choice of colours shall be as selected by the EIC. carrier profiles shall be installed first sqm 280 ₹ 5,092.00 ₹ 1,425,760.00

and levelled accurately at 1 200 mm centres and suspended at maximum 1 000 mm centres directly from the

structural soffit or from a primary angle section . Primary grid to be suspended at not more than 1 200 mm

centres M6 threaded rod or approved hangers with suspension height void minimum 150 mm.

PRINTED MATEL BAFFLE CEILING : Providing of Baffle ceiling system comprises of 50 mm x 100 mm (50

mm width & 100 mm Height) U Shape printed baffles as per approved design. Panels shall be made of 0.5

mm thick galvanized steel after Powder-coated and length up to 4000 mm. Panel shall be high corrosion

resistance and good color stability. Centre to Centre panel gap will be 150 mm. Panels are fixed on to roll

formed carriers 20 mm wide x 40 mm deep out of 0.80 mm G.I sheet Powder-coated color with cutouts to hold

the panels in module of 50 mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 6

mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max. 1200 mm

c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon inserts. Panels are factory cut in

lengths up to maximum 4.0 m to suit site dimensions or shop drawings. Top cap and side cap are used to

cover the edges of the panels.

PET BAFFLES CEILING : Providing and fixing baffles in suggested cross section in upto 200 mm depth or as

approved by EIC/Designer fabricated with upto 150 mm wide in box/U Section 9mm thk PET in design and

CNC cut profile as per the instructions of the EIC/Designer .Cost to include upto 100 mm spacing hung from

7.12 NSR Existing Ceiling and Slab in Colour and Profile as designed by EIC/Designer, cost to include Clutch wire / M6 sqm 65 ₹ 7,200.00 ₹ 468,000.00

threaded rod or approved hangers with suspension height void minimum 150 mm. Installation to be done as

per the manufacturers proprietary Specs according the Ceiling Design of the EIC/Designer. Shop Drawing of

formation pattern to be furnished by contractor for approval of the EIC.

PERFORATED MATEL BAFFLE CEILING : Providing & Ifixing of Baffle ceiling system comprises of 50 mm x

100 mm (50 mm width & 100 mm Height) U Shape perforated panels in RAL finish. Panels shall be made of

0.5 mm thick galvanized steel and length up to 4000 mm. Panel shall be high corrosion resistance and good

color stability. Centre to Centre panel gap will be 200 mm. Panels are fixed on to roll formed carriers 20 mm

7.13 NSR wide x 40 mm deep out of 0.80 mm G.I sheet Powder-coated color with cutouts to hold the panels in module sqm 75 ₹ 11,000.00 ₹ 825,000.00

of 50 mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 6 mm dia. galvanized

steel wire rod hanger with special height adjustment suspension clip at max. 1200 mm c/c. Panels are factory

cut in lengths up to maximum 4.0 m to suit site dimensions or shop drawings. Top cap and side cap are used

to cover the edges of the panels.

RIBBED WOODEN CEILING : Providing & fixing of Acoustical wooden Soffit panelling / Tile Grid consisting of

base frame treated with anti-termite chemical of standard/ approved make. Panels to be installed as per

specification. The Timber melamine effect acoustic wall panels made out of Fire Rated MDF core material.

The acoustic wall panels shall be in size of 128x2440x18mm (Thk). Wall slats to be Perforated having

perforation to 25/30 mm diameter holes, at 32/35 mm c/c at the back face, and front of the panels to have cut

with grooves of 3mm at 16mm c/c.The back of timber melamine panels shall be laminated with Soundtex

black acoustic tissue to provide NRC not less than 0.6-0.7. The acoustic timber wall panels shall be with

tongue and groove detailing along the length of panels, with square edges on 2 sides along the width of

panels. The wall panels shall be clipped into aluminium channels and clips Keel and Fastener system at

600mm c.c. Density -800kg /m3, R.H 70, Fire Rated Euro Class B and C formerly Class 0 and Class 1

BS476or equivalent IS Codes part 6 and 7 respectively. Shop Drawing of CNC pattern to be furnished by

contractor for approval of the EIC.

VENEERED PLY CEILING : Providing and fixing Wooden ceiling fabricated of 19 mm Thk BWP Ply

as approved by the Engineer In charge and 4mm Thk Veneer Finished with PU/Melamine as per

Engineer In charges Instruction . Overall setup to be mounted on the framework as specified for

7.15 Gypsum Ceilings in this Tender, rates quoted shall also include the cutting an provisioning of Light sqm 95 ₹ 5,200.00 ₹ 494,000.00

fixtures and other services. Overall specs to be same as the Gypsum Ceiling in this Tender.

Provision for making Grooves as per the instruction of the Engineer In charge. Installation to be done

as per the manufacturers proprietary Specs according the Ceiling Design of the Engineer In charge.

ROOFING / FALSE CEILING WORK TOTAL ₹ 7,922,139.70 ₹ 7,309,380.00

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

DEMOLITION DISMANTLING & HOUSEKEEPING TOTAL ₹ - ₹ -

9 SUB HEAD-IX :- WATER PROOFING WORK

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of

W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS

2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

9.1 22.3 (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound sqm 311.5 ₹ 769.60 ₹ 239,730.40

in recommended proportion including rounding off junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and

pasted to Each other with bitumen @ 1.7 kg/sqm).

WATER PROOFING WORK TOTAL ₹ 239,730.40 ₹ -

10 SUB HEAD- X :- SIGNAGE & MISCELLANEOUS ITEMS

FROSTED GLASS SPARKLE FILM

Providing and applying self adhesive clear film of same or Equivalent approved make to glazed partitions as

10.1 NSR - 30 per design and detail. Printed in white and other approved colours as per Graphic patterns to be computer cut sqm 564 ₹ 1,473.90 ₹ 831,277.93

selected from manufacture's design pattern.

Note : Installed film to be measured and paid for the actual fixed area only.

Providing and fixing of vinyl graphics as per approval by the EIC, Cost to also Include preparation of the

10.2 NSR - 31 surface to receive the film. Rate to include all wastages, cutting as per the design provided by the EIC. sqm 90 ₹ 1,842.37 ₹ 165,813.42

Note : Film to be

measured and paid for the actual fixed area only.

Fabricate and install corporate logo as per company supplied artwork. Logo to be in 15/18mm Thk Acrylic/

10.3 NSR - 33 MDF Letter 3 D Letter cuts . Signage of owner’s Logo, Typeface etc. as required. Overall size of the logo to Each 4 ₹ 36,847.00 ₹ 147,388.00

be between 450 to 750 mm ht. Cost to include 4 no's of paper cut mock-up in real size Design to be approved

by EIC before Procurement. Mock-up to be done as per the client logo vector file.

PUSH PULL SIGNAGE

Providing and fixing Plotter Cut 3M/Avery vinyl signages on glass doors of over all size of pictogram to be

Sample to be approved by the EIC.

FIRE EXIT SIGNAGE

Providing and fixing 'FIRE EXIT' letters signage (With 'or' without directional arrows as per signage plan, ref.

EIC). Signage to be made of 3mm thick foam board with edge to edge self adhesive self-luminescent Forex or

10.5 NSR - 35 equivalent vinyl stuck on it. Fix Green vinyl to cover Forex vinyl leaving 6mm border around edges with 'EXIT' Each 36 ₹ 4,201.00 ₹ 151,236.00

letters cut-out. (Note : 'EXIT' letters to be self-luminescent and not the background). 'EXIT' letters height shall

be 150 HT. double side Raised ceiling suspended with chain link and hook. Unidirectional, printed both sides

with single arrow OR double arrow. Design to be approved by EIC before Procurement.

EVACUATION PLAN

10.6 NSR - 36 Providing & Fixing Fire Exit Route Maps - Photo Luminescent Vinyl + Clear Print mounted on 4mm Thk. Each 24 ₹ 4,127.00 ₹ 99,048.00

Acrylic sheet of Max size 500mm x 400 mm. Design to be approved by EIC before Procurement.

RECESSED MARKER TRAY

P/F Auminium Recessed pen and duster holder for dry wall of Height: 75mm and Depth: 60mm or

Equivalent with Matching End Caps on both sides. Contractor to make provision in Wall for cutting and

securely fixing and setting in the partition as per the height and the length specified by the EIC.

Preparation of complete set of shop drawings including finishing, MEP services, details, design calcualtions

etc. and any other details as and when

desired by Engineer Incharge/ client. A qualified professsional for the purpose shall be appointed after due

appproval from Engineer InCharge.

SIGNAGE & MISCELLANEOUS ITEMS TOTAL ₹ - ₹ 4,294,624.35

11 SUB HEAD- XI :- MILL WORKS & JOINERY

General Notes: Caracas: Fabricating and fixing built up storage cupboards as per detail. All sides and Top,

bottom along with shelves to be made out of 19mm FR Ply as approved by the EIC. The storage Back to be

formed of 25 mm thick FR Ply as approved by the EIC. All internal and External surfaces to be faced with 1

mm thick laminate of approved shade. Laminate to be pasted with High Quality fast setting Adhesive, Cost to

include all necessary fittings like tension hinges, ball catchers, tower bolts, locks, handles, adjustable shelves

etc. as per directions of EIC.

Shelves to be provided as per Requirement and Drawings provided by the EIC. Adjustable Shelves to be

provided as per the requirement and to be and to be supported on SS Brackets. All the door and other

exposed edges shall be Finished with the PVC Edge Banding of approved make and Colour with provision of

finger grooves. Drawers shall be provided as per the requirement and Drawings of the EIC with fittings and

NSR Soft Closing Channel as approved by the EIC .

The storage to have all necessary hardware, locks, handle etc. complete as

per detail. All provision of fixing/hanging the Storage on the Wall shall be done and included in the quoted

Storage to be complete with hardware installed as directed to consist of the following: Shutter to have

automatic spring loaded hinge of approved make installed strictly a per manufacturers guidelines with

requisite too /jigs. Each set of shutters /drawer to be provided with 1no. multi purpose lock as specified, SS

Knob/ handles, auto bolt, etc. or as specified by the EIC. Typical Depth Considered to be up to 450 mm

Unless Specified by the EIC.

(For Calculation of Rates the Overall front elevation

area shall be measured)

TYPICAL LAMINATED SHUTTER STORAGE

11.1 NSR Providing and fixing storage of depth up to 450 mm with Caracas and general Spec as 11.0 as approved by sqm 160 ₹ 9,500.00 ₹ 1,520,000.00

the EIC and faced with 1.00 mm thick laminate and PVC edge Banding as per the selection of the EIC.

TYPICAL OVER HEAD STORAGE LAMINATED

Providing and fixing storage. up to 1200 mm height and depth up to 400 mm with Caracas and general Spec

as approved by the EIC faced with 1.00 mm thick laminate and PVC edge Banding as per the selection of the

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

LOW HEIGHT LAMINATE STORAGE: Providing and fixing storage of depth up to 650 mm with Caracas and

11.3 NSR as approved by the EIC and faced with 1.00 mm thick laminate and PVC edge Banding as per the selection of sqm 43 ₹ 10,500.00 ₹ 451,500.00

LOW HEIGHT WATER RESISTANT STORAGE: Providing and fixing storage of approved height and depth

up to 650 mm with Caracas and Shutters/ Shelves / Drawers to be made out of 25 mm thick BWP Ply

board as approved by Engineer In charge with all surfaces faced with upto 1.25 mm thick laminate and PVC

edge Banding as per the selection of the Engineer In charge.

LOW HEIGHT LAMINATED PLANTER STORAGE

11.5 NSR Providing and fixing storage. up to 1200 mm height and depth up to 300 mm with shutters design as Each 58 ₹ 8,000.00 ₹ 464,000.00

approved by the EIC finished with 1.00 mm thick laminate and Planter box on top.

11.6 NSR FULL HEIGHT OPEN SHELVE LAMINATED LIBRARY & AWARD STORAGE sqm 19.5 ₹ 15,000.00 ₹ 292,500.00

RECEPTION DESK (2nd & 3rd FLOOR)

Supply and installing reception desk as per EICs design. Reception desk to consist of front and Side Runner

along with storage units. Front unit to have additional horizontal surface at ht. 1100 mm above the floor level

and Working Top at 750 mm Height. Front & sides finished with Lacquered Glass / Acrylic Solid Surface with

Grooves and colour as approved, with machine cut & polished edges and sides finished All other exposed

surface faced with 1mm Thk Laminate to EIC’s approval. Table to have wire management detail, if required.

Movable Laminated drawer units to consist of one pencil drawer of 75 mm ht, two equal drawers and bottom

filing system drawers. (Overall size 800mm X 1800mm)

RECEPTION DESK (4th FLOOR MAIN RECEPTION)

Supply and installing reception desk as per EICs design. Reception desk to consist of front and Side Runner

along with storage units. Front unit to have additional horizontal surface at ht. 1100 mm above the floor level

and Working Top at 750 mm Height. Front & sides finished with Lacquered Glass / Acrylic Solid Surface with

Grooves and colour as approved, with machine cut & polished edges and sides finished All other exposed

surface faced with 1mm Thk Laminate to EIC’s approval. Table to have wire management detail, if required.

Movable Laminated drawer units to consist of one pencil drawer of 75 mm ht, two equal drawers and bottom

filing system drawers. (Overall size 1225mm X 3600mm)

RECEPTION DESK (4th FLOOR CMD RECEPTION)

Supply and installing reception desk as per EICs design. Reception desk to consist of front and Side Runner

along with storage units. Front unit to have additional horizontal surface at ht. 1100 mm above the floor level

and Working Top at 750 mm Height. Front & sides finished with Lacquered Glass / Acrylic Solid Surface with

Grooves and colour as approved, with machine cut & polished edges and sides finished All other exposed

surface faced with 1mm Thk Laminate to EIC’s approval. Table to have wire management detail, if required.

Movable Laminated drawer units to consist of one pencil drawer of 75 mm ht, two equal drawers and bottom

filing system drawers. (Overall size 800mm X 2300mm)

HIGH COUNTER BAR STYLE

Supply and installing counter as per the Design and Detail provided by the EIC. Formed on Existing Walls Or

Window along with Provision of landscape features and Foot Rest. Overall Depth of 500 mm and Height of

1050 mm . shop drawing shall be submit by the contractor to EIC for approval

11.11 NSR Supply & installing of bench as per the Design and Detail provided by the EIC. Top ht. 450 mm & width upto Rm 20 ₹ 25,000.00 ₹ 500,000.00

500 mm in fabric finish, without back & base in laminate finish and same shall be complete in all respect.

MILL WORKS & JOINERY TOTAL ₹ - ₹ 5,990,000.00

12 SUB HEAD- XII :- CURTAINS & BLINDS

Notes: As per the following or equivalent specifications based on the standard Manufacturers Product: Top

Tube: Made of extruded aluminium 38mm dia. with wall thickness of 1.2mm with spline adoptable to

accommodate clutch as per approved make. Clutch Mechanism: Moulded plastic having antifriction additive

with high strength Glass fibre reinforcement polyester and should have a minimum lifting capacity of 8 lbs.

Clutch mechanism shall be crash proof, prevent slippage and shall raise and lower smoothly to any desired

height. Operating Chain: #10 plastic/steel ball chain (or as per manufacturer's standard) adoptable to the

clutch pitch for smooth, quiet lifting & lowering of blind.

Locking Member: #12 steel stop locks for limit setting adoptable to the steel chain or as per manufacturer's

standard. Bottom Bar /Weight: Aluminium extruded circular section with powder coated finish matching the

roller fabric -Min weight to be 365 gms / RMTS for a perfect fall of fabric to avoid warpage / floating.

12.1 NSR - 39 Installation to be insert type with end caps to give a neat look. Fabric shade: As approved sqm 650 ₹ 1,434.88 ₹ 932,672.00

Fabric: Openness factor/Light Transmission : As Approved

Fire rating of the fabric : Class - A, NFPA - 701 TM

Width : 180-250cm as per manufacturer standard

Dimensional stability: Warp: <1 Weft : <1

Colour fastness to Light.......ISO 105 B02 : 5/6

Shade Orientation: Regular roll, shade cloth fall at window side of roller.

Configuration: Single band

Providing and Fixing of Roller Blinds 5% Openness , Fabric Composition: Fabric Composition: 30% Polyester,

70% Vinyl on Polyester

Digitally signed by AMIT

S.No DSR-2023 DESCRIPTION UNIT TOTAL Qty RATE

Notes: As per the following or equivalent specifications based on the standard Manufacturers Product: Top

Tube: Made of extruded aluminium 38mm dia. with wall thickness of 1.2mm with spline adoptable to

accommodate clutch as manufacturer's approved make. Clutch Mechanism: Moulded plastic having

antifriction additive with high strength Glass fibre reinforcement polyester and should have a minimum lifting

capacity of 8 lbs. Clutch mechanism shall be crash proof, prevent slippage and shall raise and lower smoothly

to any desired height. Operating Chain: #10 plastic/steel ball chain (or as per manufacturer's standard)

adoptable to the clutch pitch for smooth, quiet lifting & lowering of blind.

Locking Member: #12 steel stop locks for limit setting adoptable to the steel chain or as per manufacturer's

standard. Bottom Bar /Weight: Aluminium extruded circular section with powder coated finish matching the

roller fabric -Min weight to be 365 gms / RMTS for a perfect fall of fabric to avoid warpage / floating.

12.2 NSR - 40 Installation to be insert type with end caps to give a neat look. Fabric shade: As approved sqm 180 ₹ 1,327.00 ₹ 238,860.00

Fabric: Openness factor/Light Transmission :As Approved

Fire rating of the fabric : Class - A, NFPA - 701 TM

Width : 180-250cm as per manufacturer standard

Dimensional stability: Warp: <1 Weft : <1

Colour fastness to Light.......ISO 105 B02 : 5/6

Shade Orientation: Regular roll, shade cloth fall at window side of roller.

Configuration: Single band

Providing and Fixing of Blackout Blinds 0% Openness , Fabric Composition: Fabric Composition: 100%

Polyester, 0% Vinyl on Polyester

HONEYCOMB MOTORIZED BLINDS:

Providing and Fixing of Motorization components for Honeycell Blinds. Roller tube shall be of extruded alloyed

aluminium with 50mm O.D and a minimum wall thickness of 1.5 mm . It shall be designed to accommodate a

Motorisation Unit for desired automated operation. The Motors shall have following specs: Nominal Torque- 6

Nm/ Nominal Speed-17 rpm/Normal Supply Voltage-230 V/ Frequency-50 Hz/Current at nominal Torque-90

W/Rated Current-.45 Amp.

Providing and Fixing Honeycell Blinds: Translucent Honeycell Blinds. The fabric shall be non woven polyester

with pleate dimension 40mm high quality sealing in variable of light filtring option.

MOTOR FOR ROLLER BLINDS:

L2 riveting distance (mm) 473

Rated Voltage (V) 230

Rated Power consumption (W) 80

Rated Current (A) 0.4

Running time before thermal cut off (min) 4

Thermal cut off temp (°C) 140

Average running noise (dbA) 52

Minimum tube diameter 40 X 1.5

Motor weight (kg) 1.08

Cable length (M) 3

Number of cores in cable 2

Cross section of cable (mm²) 0.75

Index Protection IP44

12.5 NSR-43 REMOTE

Single track Each 5 ₹ 3,760.00 ₹ 18,800.00

CURTAINS & BLINDS TOTAL ₹ - ₹ 2,514,332.00

Digitally signed by AMIT

Item Description (All items are SITC nature, it may not be Unit Price Total Amount

Item Description (All items are SITC nature, it may not be Unit Price Total Amount

Sr No UoM Total Qty

mentioned in the description of the items) with GST with GST

SITC of Active LED with with pixel pitch 1.5mm with tentative size

10'x6' (+/- 50mm) with wall mounting arrangement with minimum

Screen Rosolution (Dots) 2288x1352 with required controller , ED

1 Type Black SMD 3in1 1212, Brightness minimum (nit) 700, Refresh No's 1 ₹ 3,342,730 ₹ 3,342,730

Rate (Hz) ≥3840, Gray scale(Bit) 14 or higher, Contrast Ratio

4000:1 or higher, Viewing Angle (H/V) (°) 160/140, or higher BIS ,

CE and FCC etc all complete

SITC of Interactive Display Size: 98", Brightness >= 350 nits

Resolution: 3840X2160 (UHD), Response Time: 6ms, Viewing

178/178 with i5 10th Generation OPS, 8GB RAM & 256 GB SSD

with Windows 10.

SITC of Interactive Display Size: 85''-86", Brightness >= 350 nits

Resolution: 3840X2160 (UHD), Response Time: 6ms, Viewing

178/178 with i5 10th Generation OPS, 8GB RAM & 256 GB SSD

with Windows 10.

SITC of Interactive Display Size: 65", Brightness >= 400 nits

4 Resolution: 3840X2160 (UHD), Response Time: 6ms, Contrast Ratio No's 17 ₹ 145,100 ₹ 2,466,700

4,000:1, Viewing Angle (H/V) 178/178

SITC of Professional Large Format Display, Size: 55", Brightness:

5 >400 nits resolution 3840X2160 (UHD),Viewing Angle (H/V) No's 14 ₹ 93,440 ₹ 1,308,160

178/178 Contrast Ratio: 4000:1, with wall mount kit

SITC of Professional Large Format Display, Size: 43", Brightness:

>350 nits resolution 3840X2160 (UHD), Contrast Ratio: 5000:1,

with wall mount kit, Viewing Angle (H/V)

SITC of OPS PC with Intel Core i5, 8GB RAM, 128 GB SSD with

windows 10 operating System

SITC of Suppy of Cable Cubby with 1x HDMI, 2 x RJ45, 2x Power

8 Socket, 1 x USB charging, 1x VGA, 1 x 3.5mm Audio made up of No's 112 ₹ 10,550 ₹ 1,181,600

steel & aluminium having size of 220 x 140 mm.

SITC of Smart Podium including 21 inch touch screen with dual

touch (Fingure & Stylus), Multimedia controller, Mini PC-i5, 8GB

RAM, 256 GB SSD with windows 10 and wireless keyboard and

mouse, Along with microphone system including Gooseneck

microphone with phantom power along with all required cable

SITC of Audio Podium

Gooseneck Microphone with Phantom Power and Gooseneck

Lamp, 40 W x 2 Speakers with 20 W Subwoofer, 2 Handheld

wireless Microphone with inbuilt Amplifier.

SITC of Full HD 1080p 60fps PTZ Hybrid Video Conferencing

Camera -with 30x Optical Zoom & 16x Digital Zoom, 255

Presets , USB 3.0 & HDMI & RJ45 Based Video Output with

Hand held Remote Control

Digitally signed by AMIT

Item Description (All items are SITC nature, it may not be Unit Price Total Amount

Item Description (All items are SITC nature, it may not be Unit Price Total Amount

Sr No UoM Total Qty

mentioned in the description of the items) with GST with GST

SITC of Ultra HD 4K 60fps PTZ Hybrid Video Conferencing Camera -

with 12x Optical Zoom & 16x Digital Zoom, 255 Presets , USB 3.0 &

HDMI, RJ45 Based Video Output, PoE Support with Hand held

SITC of Ultra HD 4K 30fps USB Video conferencing Camera

with 120 degree FoV & Inbuilt Microphone, Auto framing

with 8x zoom & Handheld remote control with 3 Presets.

SITC of Wireless Conference Speakerphone with inbuilt 6-array

microphone with 360 degree Omni directional Audio Pickup with

14 up to 6 meters, inbuilt Speaker, with Multiple connectivity - 17 ₹ 48,410 ₹ 822,970

Wireless USB, Bluetooth, Wired USB, Cable to cascade units to

cover the Large Area

SITC of HDMI Matrix switcher with 4 HDMI input and 4 HDMI

output, HDMI 2.0, HDCP 2.2 / HDCP 1.4 and DVI 1.0 compliant,

Video resolution is up to 4K2K@60Hz (YUV 4:4:4), Support 18Gbps

video bandwidth, Four outputs can be individually scaled

15 (4K•1080p), should have De-embedded audio to analog L/R and 6 ₹ 47,790 ₹ 286,740

Coaxial ports output, ARC audio return to the coaxial ports

output, Built-in Web GUI for TCP/IP control, control ports:

1xTCP/IP[RJ45], 1 x RS-232 [3-pin phoenix connector]1x IR

EXT[3.5mm Stereo Minijack etc all complete

SITC of HDMI Matrix switcher with 8 HDMI input and 8 HDMI

output, HDMI 2.0b, HDCP 2.2 and HDCP 1.4 compliant, Video

resolution up to 4K2K@60Hz (YUV 4:4:4) on all HDMI ports, Dolby

Vision, HDR10+ and HLG are supported, HDMI audio pass-through

16 up to 7.1CH HD audio (LPCM, Dolby TrueHD and DTS-HD Master 1 ₹ 242,845 ₹ 242,845

Audio), Audio de-embedded is supported via analog and coax

ports, ARC, CEC and smart EDID management are supported, 1U

rack mounted design with front panel OLED display, Control via

front panel buttons, IR remote, RS-232, LAN and Web GU

SITC of Digital Conference Control unit with Camera control

functionality to enable PTZ camera for Voice tracking

Functionality, should expand be expandable and easily connected

to audio system, should have with short-circuit protection,

freestanding or 19” rack mounted, 60 channels of digital audio

transmission, 48Kz sampling and 30Hz-18KHz frequency response,

should have 16 segment equalization, AGC, AEC, AFC, USB

recording inbuilt or external, should have TCP/IP connection for

software server and controller, RS232 for control, RS232 or RS485

to achieve look at me functionality and camera control, Hot plug-

and-play, should have provision for voting functionality, should

have LCD display on controller to show all functions, should have

3.5mm headphone for monitoring, 2 audio input ports, 1x RCA, 1x

XLR and atleast 5 audio output ports for system integration, (S /

N) >97dBA, Total harmonic distortion <0.05%, Channel Crosstalk>

84dB, Dynamic range >93dB

Digitally signed by AMIT

Item Description (All items are SITC nature, it may not be Unit Price Total Amount

Item Description (All items are SITC nature, it may not be Unit Price Total Amount

Sr No UoM Total Qty

mentioned in the description of the items) with GST with GST

SITC of Digital Conference Chairmen unit with Table top

Gooseneck microphone with LED indication and priority button to

control delegate microphones, should have excellent speech

intelligibility with built-in accoustic feedback supression, Built-in

volume control for headphones, headphone sockets, Built-in

loudspeaker, Loudspeaker volume is set centrally or locally at the

control unit for all delegate units level using knob, Encryption

ensures that information within the system remains confidential,

To prevent acoustic feedback, Systems can be configured in either

daisy chain or ring topology, the built-in loudspeaker is

automatically muted when the microphone is on, 3.5 mm (0.14

in) stereo headphone sockets, Built-in volume control for

headphones, Sensitivity: -46 dBV /Pa , SNR: 70dB, Frequency

response: 30 ~ 18000Hz, should have two RJ45 connectors for

loop in loop out connectivity or star connectivity, should have 48K

full digital audio processing

SITC of Digital Conference delegate unit with Table top Gooseneck

microphone with LED indication should have excellent speech

intelligibility with built-in accoustic feedback supression, Built-in

volume control for headphones, headphone sockets, Built-in

loudspeaker, Loudspeaker volume is set centrally or locally at the

control unit for all delegate units level using knob, Encryption

ensures that information within the system remains confidential,

19 To prevent acoustic feedback, Systems can be configured in either No's 27 ₹ 29,600 ₹ 799,200

daisy chain or ring topology, the built-in loudspeaker is

automatically muted when the microphone is on, 3.5 mm (0.14

in) stereo headphone sockets, Built-in volume control for

headphones, Sensitivity: -46 dBV /Pa , SNR: 70dB, Frequency

response: 30 ~ 18000Hz, should have two RJ45 connectors for

loop in loop out connectivity or star connectivity, should have 48K

full digital audio processing

SITC of Set of two UHF wireless Hand held Microphone with dual

channel microphone receiver

SITC of Set of two UHF wireless Lapel/Color Microphone with dual

channel microphone receiver

SITC of Audio digital signal processor with 8 Audio input & 8 Audio

Output AEC, AFC, Digital Audio mixing functunality

SITC of 6.5-inch, 2-Way Ceiling Speaker, Rated Power: 30W,

Frequency Range: 65 Hz – 20 kHz, Sensitivity: 88 dB, Rated

Coverage 135° conical DMT, Maximum continuous SPL 106 dB,

Nominal impedance: 8 / 16 Ohm, Transformer taps: 30W / 15W at

100 / 70V, IP-34 Rated, Low-saturation and low-loss 70/100V

transformers with 16Ω bypass, UL and CE Certified etc all complete

SITC of 4 Channel Class-D Amplifier, Power (per channels driven):

200 W at 8 Ω / 4 Ω / 100V / 70V, FlexAmp Technology, Frequency

Response: 20 Hz – 20 kHz, Signal to Noise > 103 dB, Input

impedance >10k, balanced or unbalanced etc all complete

Digitally signed by AMIT

Item Description (All items are SITC nature, it may not be Unit Price Total Amount

Item Description (All items are SITC nature, it may not be Unit Price Total Amount

Sr No UoM Total Qty

mentioned in the description of the items) with GST with GST

SITC of 16-Port Gigabit PoE+ Ethernet Smart Switch with 2 SFP

26 SITC of Wireless Access Point etc all complete No's 7 ₹ 24,840 ₹ 173,880

SITC of 2 Meter Premium High Speed HDMI 2.0b Flexy Cable,

Bandwidth up to 18Gbps, Up to 4096x2160@60Hz at RGB 4:4:4

video resolution, High Dynamic Range (HDR10), Dolby Vision and

Hybrid log–gamma (HLG) video etc all complete

SITC of 5 Meter Premium High Speed HDMI 2.0b Flexy Cable,

Bandwidth up to 18Gbps, Up to 4096x2160@60Hz at RGB 4:4:4

video resolution, High Dynamic Range (HDR10), Dolby Vision and

Hybrid log–gamma (HLG) video etc all complete

SITC of 10 Meter Premium High Speed HDMI 2.0b Flexy Cable,

Bandwidth up to 18Gbps, Up to 4096x2160@60Hz at RGB 4:4:4

video resolution, High Dynamic Range (HDR10), Dolby Vision and

Hybrid log–gamma (HLG) video etc all complete

SITC of 15 Meter Premium High Speed HDMI 2.0b Flexy Cable,

Bandwidth up to 18Gbps, Up to 4096x2160@60Hz at RGB 4:4:4

video resolution, High Dynamic Range (HDR10), Dolby Vision and

Hybrid log–gamma (HLG) video etc all complete

SITC of Microphone Cable, 2 Conductor 22 AWG Tinned Copper,

PVC Jacket (as per actual) etc all complete

SITC of 2 Conductor 16 AWG Speaker Cable, PVC/Nylon insulation,

PVC jacket (as per actual) etc all complete

SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual)

etc all complete

SITC of 24U, Equipment Rack, with Front & Side doors, 4 No Fan

Assembly, on Top of the Rack, 4 Caster wheels, 2 no Shelfs to

34 mount the equipments which are not rack mounted 5/6 Amp. No's 2 ₹ 35,400 ₹ 70,800

Power Distribution Unit, Cable Manager & Sufficient Rack

hardwares etc all complete

Digitally signed by AMIT

PROJECT : OFFICE FACILITY FOR IRCTC AT NAUROJI NAGAR NEW DELHI

SUBHEAD : SANITARY AND PLUMBING INSTALALTION

Estimate of cost

S. DSR NO. Qty. Rate AMOUNT DSR AMOUNT NON-

Description Unit

No. 2023 TOTAL (Rs.) (INR) DSR (INR)

A Sanitary Fixture & CP Fittings

1 17.3 Providing and fixing white vitreous china pedestal type water closet

(European type) with seat and lid, 10 litre low level white vitreous china

flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm

flush bend, overflow arrangement with specials of standard make and

mosquito proof coupling of approved municipal design complete,

including painting of fittings and brackets, cutting and making good the

walls and floors wherever required.

17.3.1 W.C. pan with ISI marked white soild plastic seat and lid Each 5 ₹ 8,006.60 ₹ 40,033.00

2 17.4 Providing and fixing white vitreous china flat back or wall corner type

lipped front urinal basin of 430x260x350mm and 340x410x265mm

sizes respectively with automatic flushing cistern with standard flush pipe

and C.P. brass spreaders with brass unions and G.I clamps complete,

including painting of fittings and brackets, cutting and making good the

walls and floors wherever required :

17.4.1 One urinal basin with 5 litre white P.V.C. automatic flush-ing cistern

Parryware/Hindware/Seabird/Orient(Coral)

3 17.7 Providing and fixing white vitreous china wash basin with C.I. brackets,

15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard

pattern, including painting of fittings and brackets, cutting and making

good the walls wherever required.

17.7.2 White Vitreous China Wash basin size 630x450 mm with a single 15

mm C.P. brass pillar tap

4 17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass

single hole basin mixer of approved quality and make, including

painting of fittings and brackets, cutting and making good the walls

wherever required:-

(a) White Vitreous China Wash basin size 550x400 mm with a

15 mm CP Brass single hole basin mixer Each 5 ₹ 3,960.55 ₹ 19,802.75

5 17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per

IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including

painting of fittings and brackets, cutting and making good the walls

wherever required :

6 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including

P.V.C. waste fittings complete.

17.28.2 Flexible pipe

7 17.31 Providing and fixing 600 x 450 mm bevelled edge mirror of superior

glass (of approved quality) complete with 6 mm thick hard board ground

fixed to wooden cleats with C.P. brass screws and washers comelete.

8 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

17.70.1 Bottle trap 31mm single piece moulded with height of 270 mm, effective

length of tail pipe 260 mm from the centre of the waste coupling, 77 mm

breadth with 25 mm minimum water seal, weighing not less than 260

9 17.73 Providing and fixing PTMT towel rail complete with brackets fixed to

wooden cleats with CP brass screws with concealed fittings

arrangement of approved quality and colour.

17.73.2 600 mm long towel rail with total length of 645 mm, width 78 mm and

effective height of 88 mm, weighing not less than 190 gms Each 0 ₹ 708.95 ₹ -

10 18.21 Providing and fixing uplasticised PVC connection pipe with brass ions :

18.21.2 45 cm length

13 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming

Digitally signed by AMIT

S. DSR NO. Qty. Rate AMOUNT DSR AMOUNT NON-

Description Unit

No. 2023 TOTAL (Rs.) (INR) DSR (INR)

14 18.50 Providing and fixing C.P. brass long nose bib cock of approved quality

conforming to IS standards and weighing not less than 810 gms.

18.50.1 15 mm nominal bore Each 0 ₹ 820.70 ₹ -

15 18.53 Providing and fixing C.P. brass angle valve for basin mixer and gyser

points of approved quality conforming to IS : 8931

16 N.S. Providing, fixing, testing and commissioning infra-red sensor controlled

battery operated operated mixer with suitable extension peice for wash

basin comprising light sensing device and solenoid valve of approved

make including hot and cold water mixer unit, interconnecting control

cabling between sensor & solenoid valve including cutting and making

good the walls and floors as required, all complete

17 N.S. Providing, fixing and commissioning hand drier with infra red controlled

automatic on/off arrangement ( No Touch) including cutting and making

good the walls complete with all necessary fittings to make it operational

as required,of the following make and type:(or equal approved) - for

handicapped toilet

18 N.S. Providing and fixing stainless steel finish toilet paper holder including

cutting and making good the walls complete of following make and type:

(or equal approved)

19 Providing and fixing liquid automatic soap dispenser including cutting

and making good the walls complete of following make and type: (or

equal approved)

20 Providing and fixing wall mounted auto aerosol dispenser with digital

display fixed with brackets and rowl plug complete in all respects

21 Providing and fixing stainless steel coat hooks including cutting and

making good the walls complete of following make and type: (or equal

22 Providing and fixing hand held ablution fitting (health faucet) with one

metre long flexible tube and wall hook, all complete of following make.(or

equal approved)

23 Providing and fixing stainless steel finish Automatic towel dispensor

including cutting and making good the walls complete of following make

and type: (or equal approved)

Sub total (Sanitary Fixture & CP Fittings) : Rs. ₹ 122,562.95 ₹ 186,550.00

B Soil, Waste, Vent & Rain Water pipe

1 17.35 Providing and fixing soil, waste and vent pipes.

17.35.1.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 Metre 240 ₹ 1,180.75 ₹ 283,380.00

17.35.2 75 mm diameter

Digitally signed by AMIT

S. DSR NO. Qty. Rate AMOUNT DSR AMOUNT NON-

Description Unit

No. 2023 TOTAL (Rs.) (INR) DSR (INR)

17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 Metre 0 ₹ 1,186.00 ₹ -

2 17.37 Providing and fixing M.S. holder bat clamps of approved design to sand

cast iron/cast iron (spun) pipe embedded in and including cement

concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand :

4 graded stone aggregate 20mm nominal size) including cost of cutting

holes and making good the walls etc.

3 17.38 Providing and fixing bend of required degree with access door

insertion rubber washer 3mm thick bolts and nuts complete

17.38.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 15 ₹ 705.20 ₹ 10,578.00

17.38.2.2 75mm Sand Cast iron S&S as per IS-3989 Each 0 ₹ 522.80 ₹ -

4 17.39 Providing and fixing plain bend of required degree.

17.39.1.2 Sand cast iron S&S as per IS -3989 Each 30 ₹ 570.05 ₹ 17,101.50

17.39.2.2 Sand cast iron S&S as per IS -3989 Each 0 ₹ 390.50 ₹ -

5 17.43 Providing and fixing single equal plain junction of required degree with

acesses door, insersion rubber washer 3mm thick, bolts and nuts

17.43.1.2 Sand cast iron S&S as per IS -3989 Each 33 ₹ 925.70 ₹ 30,548.10

6 17.44 Providing and fixing single equal plain junction of required degree.

17.44.2.2 Sand cast iron S&S as per IS -3989 Each 0 ₹ 561.20 ₹ -

7 17.48 Providing and fixing single unequal plain junction of required degree.

17.48.1.2 Sand cast iron S&S as per IS -3989 Each 0 ₹ 1,032.40 ₹ -

8 17.56 Providing and fixing terminal guard.

17.56.1.2 Sand cast iron S&S as per IS -3989 Each 0 ₹ 506.00 ₹ -

17.56.2.2 Sand cast iron S&S as per IS -3989 Each 0 ₹ 404.75 ₹ -

9 17.57 Providing and fixing collar

17.57.1.2 Sand cast iron S&S as per IS -3989 Each 20 ₹ 513.15 ₹ 10,263.00

17.57.2.2 Sand cast iron S&S as per IS -3989 Each 0 ₹ 362.05 ₹ -

10 17.58 Providing lead caulked joints to sand cast iron/centrifugallly cast (spun)

iron pipes and fittings of dia metre:

11 17.59 Providing and fixing M.S stays and clamps for sand cast

iron/centrifugally cast (spun) iron pipes of dia metre.

12 17.60 Providing and fixing trap of self cleansing design with screwed down or

hinged grating with or without vent arm complete, including cost of

cutting and making good the walls and floors :

17.60.1 100mm inlet and 100mm outlet

17.60.1.1 Sand cast iron S&S as per IS: 3989 Each 10 ₹ 1,996.50 ₹ 19,965.00

Cutting chases in brick masonry walls for following diameter sand cast

iron/centrifugally cast (spun) iron pipes and making good the same with

cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone

aggregate 12.5 m nominal size) including necessary plaster and

pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

14 17.65 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent

pipes and fittings with two coats of synthetic enamel paint of any colour

such as chocolate grey, or buff etc. over a coat of primer (of approved

quality) for new work :

17.65.1 100 mm diameter pipe Metre 240 ₹ 82.80 ₹ 19,872.00

Digitally signed by AMIT

S. DSR NO. Qty. Rate AMOUNT DSR AMOUNT NON-

Description Unit

No. 2023 TOTAL (Rs.) (INR) DSR (INR)

17.65.2 75 mm diameter pipe Metre 0 ₹ 62.95 ₹ -

15 N.S Providing and fixing, testing and commissioning of reducing floor drain

of 110x63 mm OD as floor drain in cement concrete 1 : 2 : 4 float with

floor complete in all respects. Each 0 ₹ 296.00 ₹ -

15 N.S Providing and fixing floor trap Extension Piece made out of 100 mm dia

M.S pipe ( medium grade) of required length (upto 450 mm) with 32 mm

to 50 mm dia threaded maleable iron sockets ( maximum 4 nos.) welded

as side inlets, neatly finished, inside and outside epoxy painted,

including the cost of jointing with floor trap with dripseal joint.

16 N.S. Providing and fixing 125 mm dia, Stainless steel grating with frame for

floor traps or drains of required pattern with 25 dia waste hole for basin

& sink flexible waste pipe or without hole as/site requirement including

cutting and making good the floors complete.

17 N.S Providing and fixing screwed down type nickel bronze alloy cast floor

cleanout/ CO with opening arrangements for soil / waste pipe and other

necessary fittings inlcuding jointing, all complete as per standard detail.

18 N.S Providing, installing, testing and commissioning of Grease Separator

having grease storage capacity of 9 litre and total iquid holding capacity

of 34.3 litre , all as per standard design and including making

connections with scullery sink

19 N.S Providing, installing, testing and commissioning of package sump unit

with built-in submersible drainage pump, nonreturn valves, cutter,

electrical panel/starter, all as per standard design and including making

connections with grease separator/sink waste pipes drain pipe and make

20 N.S Providing and fixing in position, the following G.I. medium class Waste

Pipes (IS:1239) with all necessary specials complete, cutting and

chasing walls, floors, etc. and making good the same including painting

the pipes with two coats of anti-corrosive paint.

a) 32 mm dia pipe Metre 0 ₹ 525.00 ₹ -

21 N.S Making connection with existing C.I. Soil and Waste pipework. The

work includes loosening / removing the existing lead joints, rotating the

direction of the existing tees, bends etc. so as to connect with new

branch lines from the toilets, redoing the joints with 'Dripsel', testing,

commissioning all complete. Any pipe piece, fittings etc. required to

make the connection shall be measured in Item No. 2.1

(Soil, Waste, Vent & Rain Water pipe)

C Internal Water Supply

1 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain &

brass threaded fittings, including fixing the pipe with clamps at 1.00 m

spacing. This includes jointing of pipes & fittings with one step CPVC

solvent cement and testing of joints complete as per direction of

Engineer in Charge.

Internal work - Exposed on wall (For Water supply D/N in shaft &

terrace & riser in terrace level)

18.7.1 15 mm nominal outer dia Pipes Metre 35 ₹ 286.80 ₹ 10,038.00

18.7.2 20 mm nominal outer dia Pipes Metre 90 ₹ 335.00 ₹ 30,150.00

18.7.3 25 mm nominal outer dia Pipes Metre 105 ₹ 401.55 ₹ 42,162.75

18.7.4 32 mm nominal outer dia Pipes Metre 25 ₹ 518.75 ₹ 12,968.75

Digitally signed by AMIT

S. DSR NO. Qty. Rate AMOUNT DSR AMOUNT NON-

Description Unit

No. 2023 TOTAL (Rs.) (INR) DSR (INR)

18.7.5 40 mm nominal outer dia Pipes Metre 10 ₹ 702.95 ₹ 7,029.50

18.7.6 50 mm nominal outer dia Pipes Metre 120 ₹ 934.15 ₹ 112,098.00

2 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain &

brass threaded fittings, including fixing the pipe with clamps at 1.00 m

spacing. This includes jointing of pipes & fittings with one step CPVC

solvent cement and testing of joints complete as per direction of

Engineer in Charge.

Concealed work including cutting chases and making good the

18.8.1 15mm nominal outer dia pipes Metre 120 ₹ 497.80

18.8.2 20mm nominal outer dia pipes Metre 50 ₹ 537.60 ₹ 26,880.00

18.8.3 25mm nominal outer dia pipes Metre 0 ₹ 627.25 ₹ -

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply including all CPVC plain &

threaded fittings This includes jointing of pipes & fittings with one step

solvent cement, trenching, refilling & testing of joints complete as per

directionof Engineer in Charge.

18.9.5 40mm nominal outer dia pipes (for sump pump) Metre 0 ₹ 563.05 ₹ -

18.9.6 50mm nominal outer dia pipes (for sump pump) Metre 0 ₹ 794.25 ₹ -

4 18.18 Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete with hard chrome plated ball

inside PTFE (Teflon) seat & ring with chrome plated centre handle with

female BSP threads complete:in all respects (PN 1.6). Tested to 25

5 18.19 Providing and fixing gun metal non- return valve of approved quality

(screwed end) :

18.19.2.2 32 mm dia. nominal bore Each 0 ₹ 850.25 ₹ -

18.19.4.2 50 mm dia. nominal bore Each 0 ₹ 1,445.15 ₹ -

6 N.S. Providing and fixing thermal insulation tubing for hot water pipes

(exposed/chases/burried locations), over pipes of following nominal

bores and thickness including all required accessories, protection as per

manufacturer's recommendations, complete in al respect.

Concealed Piping in Toilet.

a) 15mm dia (6 mm thick insulation) Metre 40 ₹ 71.00 ₹ 2,840.00

b) 20mm dia (6 mm thick insulation) Metre 5 ₹ 125.00 ₹ 625.00

7 N.S Providing, fixing, testing & commisioning of cast iron slim type butterfly

PN 1.6 valve complete corresponding flanges, bolts, nuts 1.5 mm thick

EPDM rubber gasket. (IS: 13095)

8 N.S Providing and fixing electric water storage heater (geyser) of following

capacities including making inlet / outlet connections, of approved

Sub total ( Internal Water Supply) : Rs. ₹ 246,600.30 ₹ 107,445.00

Digitally signed by AMIT

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR AMOUNT NON-DSR

I SUB HEAD (I) :- INTERNAL WIRING

1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

2 1.55 Wiring for group controlled (looped) light point/ fan point/call bell point

(without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed PVC conduit, and

earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc as required.

3 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed medium class PVC conduit

1.5 3000 Metre

alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core

cable for loop earthing as required. ₹ 433.00 ₹ 1,299,000.00

4 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed medium class PVC conduit

alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core

cable for loop earthing as required. ₹ 662.00 ₹ -

5 CONTROL WIRING

Supply and drawing following size of FRLS PVC insulated copper conductor ,

1.17 single core cable in the eixsting sufrace/ recessed steel/ PVC conduit as

6 SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes

1.7 of FR PVC insulated copper conductor, single core cable in surface/

recessed steel conduit as required

1.7.8 4 x 4 sq.mm + 2 x 4 sq.mm. earth wire 0.00 meter ₹ 677.00 ₹ -

1.7.9 4 x 6 sq.mm + 2 x 6 sq.mm. earth wire 0.00 meter ₹ 924.00 ₹ -

1.7.11 4 x 16 sq.mm + 2 x 6 sq.mm. earth wire 0.00 meter ₹ 1,645.00 ₹ -

7 Supplying and fixing of following sizes of medium class PVC conduit along

with accessories in surface/recess including painting in case of surface

conduit, or cutting the wall and making good the same in case of recessed

conduit as required.

8 Supplying and fixing following modular switch/ socket on the existing modular

1.24 plate & switch box including connections but excluding modular plate etc. as

9 Supplying and fixing modular blanking plate on the existing modular plate &

switch box excluding modular plate as required. 850.00 ₹ 34,000.00

10 Supplying and fixing following size/module, GI box along with Modular base &

cover plate on existing modular metal boxes etc. as required.

Supply and fixing of suitable size GI box with modular plate and cover in

front on surface or in recess including providing and fixing 3 pin 5/6 amps

modular socket outlet and 5/6 amps. modular switch, connection etc. as

required. (UPS POINT INCLUDED) 10.00 Each ₹ 477.00 ₹ 4,770.00

12 S/F power plug point modular type accessories :-

Supply and fixing of suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16

amps modular socket outlet and 15/16 amps. modular switch, connection etc.

as required. (UPS POINT INCLUDED) 25.00 Each ₹ 586.00 ₹ 14,650.00

13 S/F power plug point modular type accessories :-

Supply and fixing of suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 2 nos 3 pin 5/6 A

1.32 modular socket out let and 2 nos 5/6 A modular switch connections etc, as

required ( For light plug to be used in non residentional buildings )

Digitally signed by AMIT

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR AMOUNT NON-DSR

14 S/F modular type blanking plate :-

Supply and fixing modular blanking plate on the existing modular plate &

switch box excluding modular plate as required. 0.00 Each ₹ 40.00 ₹ -

15 Supply and fixing of 20A, 240V, SPN industrial socket outlet, with 2 pole and

earth, metal enclsoed plug top alognwith 20A, "C" curve SP MCB, in sheet

2.18 steel enclsoure on sureface/ recessed with chained metal cover for the

socket outlet and complete connections, testing and commissioning etc. as

16 Supply and fixing of 30A, 415V, TPN industrial socket outlet, with four pole

and earth, metal enclsoed plug top alognwith 30A, "C" curve TP MCB, in

2.2 sheet steel enclsoure on sureface/ recessed with chained metal cover for the

socket outlet and complete connections, testing and commissioning etc. as

TOTAL SUB HEAD (I) (DSR'2022) ₹ 8,189,108.00 ₹ -

II SUB HEAD (II) :- DISTRIBUTION BOARDS & MCB's

1 Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

2 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in the

existing MCB DB complete with connections, testing and commissioning etc.

3 Supplying and fixing following rating, four pole, 415 volts, isolator in the

2.13 existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing of following ways surface/ recess mounting, vertical

volts, TPN MCB distribution board of sheet steel, dust protected, duly powder

painted, inclusive of 200 amps tinned copper bus bar, common neutral link,

bar, din bar for mounting MCB’s (but without MCB’s and incomer ) as

(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are

5 Supplying and fixing following way, single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper

2.3 bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 Supplying and fixing following rating, double pole, (single phase and neutral),

240 volts, residual current circuit breaker (RCCB), having a sensitivity current

2.14 upto 30 milliamperes in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

7 Supplying and fixing following rating ,double pole, 240 Volts, isolator in the

2.12 existing MCB DB complete with connections, testing and commissioning etc.

TOTAL SUB HEAD (II) (DSR'2022) ₹ 1,163,440.00 ₹ -

III SUB HEAD (III) :- TELEPHONE, TELEVISION & DATA SYSTEM

1 1.19 Supply and drawing co-axial TV cable RG-6 grade, 0.7 mm. Solid copper

conductor PE insulated, shielded with fine tinned copper braid and protected

with PVC sheath in the existing surface / recessed steel/ PVC conduit as 1200.00 meter ₹ 47.00 ₹ 56,400.00

2 1.21 Supply and fixing of following sizes of medium class PVC conduit

alongwith accessories in surface/recess including cutting the wall and making

good the same in case of recessed conduit as required.

Digitally signed by AMIT

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR AMOUNT NON-DSR

3 1.24 Supplying and fixing following modular switch / socket on the existing

modular plate & switch box including connections but excluding modular

plate etc. as required.

1.24.7 TV socket outlet 95.00 Each ₹ 95.00 ₹ 9,025.00

4 1.27 Supplying and fixing following size / modules, GI box alongwith modular base

& cover plate for modular switches in recess etc. as required.

TOTAL SUB HEAD (III) (DSR'2022) ₹ 531,445.00 ₹ -

IV SUB HEAD (IV) :- FIXING, CONNECTING & TESTING

1 MR Supply, installation, testing and commissioning of sheet metal enclosed

450(W) x 150(D) x 300(H) mm insulated earth distribution board with 1 No.

40 x 6 mm copper tinned earth bars suitable for 8/10 nos. connections 6.00 Nos ₹ 3,000.00 ₹ 18,000.00

complete with all fixing accessories as required. (UPS System Earthing)

2 MR Supply & Fixing of factory fabricated GI sheet steel raceways in floor in 2mm

thickness for bottom & sides and 2mm thick top cover, junction boxes

as required as called for including necessary civil work such as chase cutting

in screed, fixing/ jamming the raceway, aligning & levelling and finishing with

sand cement plaster:

iii. 200mm x 40mm (2mm top cover) 0.00 RM ₹ 915.00 ₹ -

3 Supply, Installation, Testing and Commisioning of Junction boxes for direct

access to cables at the intersection of raceways supplied completely with

MR base and cover plates, height adjustable junction box 65- 90 mm including all

accessories complete in all respect as per the directions of engineer i

4 MR Supply and Fixing of factory fabricated GI ceiling sheet steel raceway

openable bottom cover junction boxes made from 2mm thick G.I. sheets for

top, bottom and sides and complete with 2mm thick bottom cover

complete with rubber gasketing, painting. The junction box shall be suitable

to accommodate the raceways specified above. Necessary civil work to

support/ clamp from RCC slab need to be included here too. All supporting

arrangement is included in the ceiling raceways

5 MR Fabricating ,supplying to site of installation, installation of 500 mm size of

105 mm height mesh type EZ -Electroplated Zinc cable tray including

threaded G.I. down rods, dash fasteners , fixing accesories etc. complete as

TOTAL SUB HEAD (IV) (NON-DSR) ₹ - ₹ 2,369,465.00

V ERECTION OF LIGHTING FIXTURES AND FANS

1 1.41 Installation, testing and commissioning of pre-wired, flourescent fitting /

compact fluorescent fitting/ led fixtures of all types, complete with all

accessories and tubes etc. directly on ceiling / wall, including connection with

1.5 sq. mm. FR PVC insulated, copper conductor, single core cable and

earthing etc. as required. 2000.00 Each ₹ 206.00 ₹ 412,000.00

2 1.50 Installation of exhaust fan in the existing opening, including making good the

damage, connection, testing, commissioning etc. as required

3 1.51 Extra for fixing the louvers / shutters complete with frame fro exhaust fans

of all sizes. 0.00 Each ₹ 207.00 ₹ -

TOTAL SUB HEAD (V) (DSR'2016) ₹ 412,000.00 ₹ -

1 NS 1.1 Supplying of following sizes of 1.1 kV grade multicore Copper / aluminium

conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I)

complete with all amendments etc. as required

i 2C x 16 Sq.mm Cu. XLPE arm. 325.00 ₹ 493.00 ₹

ii 3C x 6 Sq.mm Cu. XLPE arm. 300.00

signed by160,225.00

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR AMOUNT NON-DSR

iii 4C x 2.5 Sq.mm Cu. XLPE arm. 400.00 Mtrs. ₹ 207.00 ₹ 82,800.00

iv 4C x 4 Sq.mm Cu. XLPE arm. 0.00 Mtrs. ₹ 297.00 ₹ -

viii 4C x 16Sq.mm Cu. XLPE arm. 1100.00 Mtrs. ₹ 953.00 ₹ 1,048,300.00

xii 4C x 95 Sq.mm AL. XLPE arm. 125.00 Mtrs. ₹ 807.00 ₹ 100,875.00

2 NS 1.2 SINGLE /THREE CORE COPPER UNARMOURED CABLE POWER /

Supply and laying of 1.1kV grade PVC insulated, unsheathed, stranded

copper conductor unarmoured cable (IS:694) in PVC pipes/ on existing cable

trays/raceways etc. including terminations:

a) 3 Core 2.5 sqmm FRLS PVC Insulated and PVC sheathed flexible cable with

bright annealed electrolytic copper conductor , 1100 volt grade confirming to

IS : 694-1990 with latest amendments, in existing Channels/ conduit in

ceiling/walls/floor including all cable termination accessories) (including body

earth for GI boxes). Colour Coding to be followed For Workstations UPS

b) 3 Core 4 sqmm FRLS PVC Insulated and PVC sheathed flexible cable with

bright annealed electrolytic copper conductor , 1100 volt grade confirming to

IS : 694-1990 with latest amendments, in existing Channels/ conduit in

ceiling/walls/floor including all cable termination accessories) (including body

earth for GI boxes). Colour Coding to be followed For Workstations UPS

c 1 x 6 Sq. mm FRLS XLPE insulated flexible copper conductor cables 200.00 Mtrs. ₹ 68.00 ₹ 13,600.00

d 1 x 10 Sq. mm FRLS XLPE insulated flexible copper conductor cables 900.00 Mtrs. ₹ 116.00 ₹ 104,400.00

e 1 x 16 Sq. mm FRLS XLPE insulated flexible copper conductor cables

f 1 x 25 Sq. mm FRLS XLPE insulated flexible copper conductor cables

g 1 x 35 Sq. mm FRLS XLPE insulated flexible copper conductor cables

h 1 x 50 Sq. mm FRLS XLPE insulated flexible copper conductor cables

i 1 x 70 Sq. mm FRLS XLPE insulated flexible copper conductor cables

3 NS 1.3 SINGLE CORE CABLE JOINT

Supplying and making of end termination for the following size of single

compression lugs and PG Threaded Nylon Flexible cable glands for single

core flexible cables

a 1 x 6 Sq. mm FRLS XLPE insulated flexible copper conductor cables 32.00 Joint ₹ 150.00 ₹ 4,800.00

b 1 x 10 Sq. mm FRLS XLPE insulated flexible copper conductor cables 24.00 Joint ₹ 150.00 ₹ 3,600.00

c 1 x 16 Sq. mm FRLS XLPE insulated flexible copper conductor cables

d 1 x 25 Sq. mm FRLS XLPE insulated flexible copper conductor cables

e 1 x 35 Sq. mm FRLS XLPE insulated flexible copper conductor cables

f 1 x 50 Sq. mm FRLS XLPE insulated flexible copper conductor cables

g 1 x 70 Sq. mm FRLS XLPE insulated flexible copper conductor cables

TOTAL SUB HEAD (VI) ₹ - ₹ 5,062,740.00

3 DSR 7 MV CABLE LAYING

DSR 7.8 Laying of one number PVC insulated and PVC sheathed / XLPE power cable

of 1.1 kV grade of following size on cable tray as required.

7.8.2 Above 35 sq. mm & Upto 95 sq. mm (clamped with 25x3mm MS metal clamp)

7.8.3 Above 95 sq. mm & Upto 185 sq. mm (clamped with 25x3mm MS metal

clamp) Mtrs ₹ 115.00 ₹ -

7.8.4 Above 185 sq. mm & Upto 400 sq. mm (clamped with 25x3mm MS metal

MV CABLE JOINTING & END TERMINATION

4 DSR 9.1 Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 kV grade as required.

- signed by AMIT

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR AMOUNT NON-DSR

Hot Dipped Galvanized Iron Cable Tray

5 DSR 4.6 Supplying and installing following size of perforated GI cable trays with

perforation not more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with M.S. suspenders including bolts

& nuts, painting suspenders etc as required.

DSR 4.6.2 150 mm width x 50 mm depth x 1.6 mm thickness 250.00 Metre ₹ 716.00 ₹ 179,000.00

DSR 4.6.4 300 mm width x 50 mm depth x 1.6 mm thickness 300.00 Metre ₹ 963.00 ₹ 288,900.00

DSR 4.6.6 450 mm width x 50 mm depth x 2.0 mm thickness 140.00 Metre ₹ 1,325.00 ₹ 185,500.00

DSR 4.6.7 600 mm width x 50 mm depth x 2.0 mm thickness 25.00 Metre ₹ 1,790.00 ₹ 44,750.00

TOTAL SUB HEAD (VII) ₹ 1,132,572.00 ₹ -

VII EARTHING STATIONS

DSR 5.6 Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including

accessories, and providing masonry enclosure with cover plate having

locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/

coke and salt as required. 4.00 Set ₹ 13,838.00 ₹ 55,352.00

DSR 5.15 Providing and fixing 25 mm x 5 mm G.I. strip on surface or in recess for

connections etc. as required. 700.00 Meter ₹ 244.00 ₹ 170,800.00

DSR 5.16 Providing and fixing 6 SWG dia GI wire in surface or in recess for loop

earthing as required. 1000.00 Meter ₹ 70.00 ₹ 70,000.00

DSR 5.14 Providing and fixing earth bus of 25 mm x 5 mm copper strip on surface for

connections etc. as required. 75.00 Meter ₹ 1,162.00 ₹ 87,150.00

DSR 11.6 Supply and embedding following dia GI Pipe (medium class) in pole collar /

foundation(during casting) for cable entry including bending the pipe to

required shape complete as required.

TOTAL SUB HEAD (VIII) ₹ 427,477.00 ₹ -

VIII DISTRIBUTION BOARDS & PANELS

Note. All MCB in the UPS pane should be D curve

NS 1 SDB LIGHT & POWER-1

i 1 Nos. 250 A, 35kA, 4P MCCB's with microprocessor based releases,

ON/OFF, RYB indications, 1 no. multifunction meter (showing all power

parameters), with selector switch, matching cast resin CT's.

3 nos phase indicating lamps (LED type) each backed up with MCB and

switch shall be provided for each incomer and buscoupler.

Provide Transient Voltage Surge Suppressor Rating 40kA class I&II along

with 63 A MPCB. Including all necessary accessories. For Switching

Operation on each incomer.

Provide Intelligent Panel Meter - multifunctional meter EM6400NG with

RS485 for all incoming feeder

i A set of TPN Aluminium bus bars with heat Shrink Sleeve rated for 300A

(after considering all necessary deratings) 3 phase 4wire, 50Hz.

ii A suitable minimum derating factor must be taken for calculation of bus bar

sizes. The bus bar size after derating shall be equal to the ampere given in

ii Maximum current density of 0.8 Amp per sq.mm is suitable for the busbar.

i 6 Nos 25 A 4P MCB's.

ii 11 Nos 63 A 4P MCB's.

iii 3 Nos 63 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

iv 2 Nos 125 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

v 1 Nos 160 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

1 Lot of control wiring

1 Set of designation plates 1.00 Set ₹ 205,045.00 ₹ 205,045.00

NS 2 SDB LIGHT & POWER-2

i 1 Nos. 250 A, 35kA, 4P MCCB's with microprocessor based releases,

ON/OFF, RYB indications, 1 no. multifunction meter (showing all power

parameters), with selector switch, matching cast resin CT's.

i 3 nos phase indicating lamps (LED type) each backed up with MCB and

switch shall be provided for each incomer and buscoupler.

Provide Transient Voltage Surge Suppressor Rating 40kA class I&II along

with 63 A MPCB. Including all necessary accessories. For Switching

Operation on each incomer.

Provide Intelligent Panel Meter - multifunctional meter EM6400NG with

RS485 for all incoming feeder

Digitally signed by AMIT

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR AMOUNT NON-DSR

i A set of TPN Aluminium bus bars with heat Shrink Sleeve rated for 300A

(after considering all necessary deratings) 3 phase 4wire, 50Hz.

ii A suitable minimum derating factor must be taken for calculation of bus bar

sizes. The bus bar size after derating shall be equal to the ampere given in

ii Maximum current density of 0.8 Amp per sq.mm is suitable for the busbar.

i 8 Nos 25/20 A 4P MCB's.

ii 3 Nos 32/40 A 4P MCB's.

ii 7 Nos 63 A 4P MCB's.

iii 3 Nos 63 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

iv 1 Nos 125 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

v 1 Nos 160 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

1 Lot of control wiring

1 Set of designation plates 1.00 Set ₹ 199,180.00 ₹ 199,180.00

NS 3 SDB LIGHT & POWER-3

i 1 Nos. 250 A, 35kA, 4P MCCB's with microprocessor based releases,

ON/OFF, RYB indications, 1 no. multifunction meter (showing all power

parameters), with selector switch, matching cast resin CT's.

i 3 nos phase indicating lamps (LED type) each backed up with MCB and

switch shall be provided for each incomer and buscoupler.

Provide Transient Voltage Surge Suppressor Rating 40kA class I&II along

with 63 A MPCB. Including all necessary accessories. For Switching

Operation on each incomer.

Provide Intelligent Panel Meter - multifunctional meter EM6400NG with

RS485 for all incoming feeder

i A set of TPN Aluminium bus bars with heat Shrink Sleeve rated for 300A

(after considering all necessary deratings) 3 phase 4wire, 50Hz.

ii A suitable minimum derating factor must be taken for calculation of bus bar

sizes. The bus bar size after derating shall be equal to the ampere given in

ii Maximum current density of 0.8 Amp per sq.mm is suitable for the busbar.

i 8 Nos 25/20 A 4P MCB's.

ii 10 Nos 63 A 4P MCB's.

iii 3 Nos 63 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

iv 2 Nos 125 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

v 1 Nos 160 Amp 35 kA TP+N MCCB's with On/Off indication lamps.

1 Lot of control wiring

1 Set of designation plates 1.00 Set ₹ 207,391.00 ₹ 207,391.00

NS 4 MDB UPS PANEL

i 3 Nos. 160 A, 35kA, TPN + N ( 100%) MCCB's with microprocessor based

releases, ON/OFF, RYB indications, 1 no. multifunction meter (showing all

power parameters), with selector switch, matching cast resin CT's.

i 3 nos phase indicating lamps (LED type) each backed up with MCB and

switch shall be provided for each incomer and buscoupler.

Provide Transient Voltage Surge Suppressor Rating 40kA class I&II along

with 63 A MPCB. Including all necessary accessories. For Switching

Operation on each incomer.

Provide Intelligent Panel Meter - multifunctional meter EM6400NG with

RS485 for all incoming feeder

i A set of TPN copper bus bars with heat Shrink Sleeve rated for 300 A

(after considering all necessary deratings) 4 pole phase 4wire, 50Hz.

ii A suitable minimum derating factor must be taken for calculation of bus bar

sizes. The bus bar size after derating shall be equal to the ampere given in

ii Maximum current density of 1.6 Amp per sq.mm is suitable for the busbar.

i 1 Nos 63 A DP MCB's.

ii 2 Nos 63 A 4P MCB's.

iii 2 Nos 100 Amp 35 kA TP+N ( 100%) MCCB's with On/Off indication lamps.

iv 3 Nos 125 Amp 35 kA TP+N ( 100%) MCCB's with On/Off indication lamps.

1 Lot of control wiring

1 Set of designation plates 1.00 Set ₹ 220,294.00 ₹ 220,294.00

Digitally signed by AMIT

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR AMOUNT NON-DSR

NS 5 SDB Server 1 &2

i 1 Nos. 125 A, 35kA, TPN + N ( 100%) MCCB's with microprocessor based

releases, ON/OFF, RYB indications, 1 no. multifunction meter (showing all

power parameters), with selector switch, matching cast resin CT's.

i 3 nos phase indicating lamps (LED type) each backed up with MCB and

switch shall be provided for each incomer and buscoupler.

Provide Transient Voltage Surge Suppressor Rating 40kA class I&II along

with 63 A MPCB. Including all necessary accessories. For Switching

Operation on each incomer.

Provide Intelligent Panel Meter - multifunctional meter EM6400NG with

RS485 for all incoming feeder

i A set of TPN copper bus bars with heat Shrink Sleeve rated for 150 A

(after considering all necessary deratings) 4 pole phase 4wire, 50Hz.

ii A suitable minimum derating factor must be taken for calculation of bus bar

sizes. The bus bar size after derating shall be equal to the ampere given in

ii Maximum current density of 1.6 Amp per sq.mm is suitable for the busbar.

i 2 Nos 63 A DP MCB's.

ii 2 Nos 63 A 4P MCB's.

iii 1 Nos 100 Amp 35 kA TP+N ( 100%) MCCB's with On/Off indication lamps.

1 Lot of control wiring

1 Set of designation plates 2.00 Set ₹ 123,004.00 ₹ 246,008.00

NS 6 UPS DB 1 to 3

i 1 Nos. 125 A, 35kA, TPN + N ( 100%) MCCB's with microprocessor based

releases, ON/OFF, RYB indications, 1 no. multifunction meter (showing all

power parameters), with selector switch, matching cast resin CT's.

i 3 nos phase indicating lamps (LED type) each backed up with MCB and

switch shall be provided for each incomer and buscoupler.

Provide Transient Voltage Surge Suppressor Rating 40kA class I&II along

with 63 A MPCB. Including all necessary accessories. For Switching

Operation on each incomer.

Provide Intelligent Panel Meter - multifunctional meter EM6400NG with

RS485 for all incoming feeder

i A set of TPN copper bus bars with heat Shrink Sleeve rated for 150 A

(after considering all necessary deratings) 4 pole phase 4wire, 50Hz.

ii A suitable minimum derating factor must be taken for calculation of bus bar

sizes. The bus bar size after derating shall be equal to the ampere given in

ii Maximum current density of 1.6 Amp per sq.mm is suitable for the busbar.

i 6 Nos 63 A 4P MCB's.

1 Lot of control wiring

1 Set of designation plates 3.00 Set ₹ 105,455.00 ₹ 316,365.00

NS 7 SDB EMERGENCY LIGHT

i 1 Nos. 63 A, 25kA, TPN + N ( 100%) MCCB's with microprocessor based

releases, ON/OFF, RYB indications, 1 no. multifunction meter (showing all

power parameters), with selector switch, matching cast resin CT's.

i 3 nos phase indicating lamps (LED type) each backed up with MCB and

switch shall be provided for each incomer and buscoupler.

Provide Intelligent Panel Meter - multifunctional meter EM6400NG with

RS485 for all incoming feeder

i A set of TPN copper bus bars with heat Shrink Sleeve rated for 100 A

(after considering all necessary deratings) 4 pole phase 4wire, 50Hz.

Digitally signed by AMIT

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR AMOUNT NON-DSR

ii A suitable minimum derating factor must be taken for calculation of bus bar

sizes. The bus bar size after derating shall be equal to the ampere given in

ii Maximum current density of 1.6 Amp per sq.mm is suitable for the busbar.

i 9 Nos 40 A DP MCB's.

1 Lot of control wiring

1 Set of designation plates 3.00 Set ₹ 65,573.00 ₹ 196,719.00

i 1 Nos. 100 A, 25kA, TPN + N ( 100%) MCCB's with microprocessor based

releases, ON/OFF, RYB indications, 1 no. multifunction meter (showing all

power parameters), with selector switch, matching cast resin CT's.

i 3 nos phase indicating lamps (LED type) each backed up with MCB and

switch shall be provided for each incomer and buscoupler.

Provide Intelligent Panel Meter - multifunctional meter EM6400NG with

RS485 for all incoming feeder

i A set of TPN copper bus bars with heat Shrink Sleeve rated for 100 A

(after considering all necessary deratings) 4 pole phase 4wire, 50Hz.

ii A suitable minimum derating factor must be taken for calculation of bus bar

sizes. The bus bar size after derating shall be equal to the ampere given in

ii Maximum current density of 1.6 Amp per sq.mm is suitable for the busbar.

i 15 Nos 25/32 A DP MCB's.

1 Lot of control wiring

1 Set of designation plates 3.00 Set ₹ 70,265.00 ₹ 210,795.00

NS 8 MCCB/ MCB Isolator

i Supply, installation, testing and commissioning of sheet metal enclosure with

160 A TPN MCCB. This shall include cable entry boxes both for incoming

and outgoing cable) 3.00 Set ₹ 18,000.00 ₹ 54,000.00

ii Supply, installation, testing and commissioning of sheet metal enclosure with

125 A TPN MCCB. This shall include cable entry boxes both for incoming

and outgoing cable) 2.00 Set ₹ 18,000.00 ₹ 36,000.00

iii Supply, installation, testing and commissioning of sheet metal enclosure with

100 A TPN MCCB. This shall include cable entry boxes both for incoming

and outgoing cable) 1.00 Set ₹ 14,000.00 ₹ 14,000.00

Supply, installation, testing and commissioning of sheet metal weather proof

enclosure with 40/63 A 4P MCB+ RCCB (300mA).This shall include cable

entry boxes both for incoming and outgoing cable) For VRV Out Door units.

TOTAL SUB HEAD (IX) ₹ - ₹ 1,970,797.00

Digitally signed by AMIT

Supply and Installation of UPS and Battery Backup.

S.no Item Description Unit Qty. Rate Amount

1 Design, and supply of installing in position,

connecting testing and commissioning of the

following UPS and Batteries complete as required.

S(Input - three phase and Output -three/ single

phase) unit as per specifications The cost shall

includes all UPS, Batteries, Rack, base frame ,

interconnection cables between UPS and battery

and all fixing accessories as required. It should be

true online, double conversion, IGBT based and

configured in n+1 configuration with parallel

a 60 KVA /54 KW in parallel operation.(Input - three

phase and Output -three phase) with 20 minutes Nos 3 ₹ 900,000.00 ₹ 2,700,000.00

battery backup and rack

b 40 KVA /36 KW in standalone Mode.(Input - three

phase and Output - three phase) with 20 minutes Nos 2 ₹ 700,000.00 ₹ 1,400,000.00

battery and rack

c 10 KVA /9 KW in standalone Mode.(Input - three

phase and Output -Single phase) with 90 minutes Nos 1 ₹ 210,000.00 ₹ 210,000.00

battery and rack

Total ( Supply & Installation) ₹ 4,310,000.00

Digitally signed by AMIT

IRCTC at New Delhi R0 HVAC Work

PRICED SCHEDULE OF QUANTITIES (as on 20-11-23)-R1

SECTION 'H' : HVAC SYSTEM FOR OFFICE AREA

S. NO ITEM DESCRIPTION UNIT QTY. RATE AMOUNT

1.0 Central Air Cleaner for AHUs

Supply, Installation, Testing & commissioning of hybrid air purification system

with central air cleaner to achieve the IAQ parmaters by reducing harmful

pollutants i.e. particulate matter (PMx), PM 2.5, allergens, pollen, smoke,

bacteria, pathogens virus, VOC's, odor etc. based on trap & kill technology.

The unit shall be in a powder coated steel casing and self contained. Unit shall

be BMS compatible having provision for BMS connectivity. It should be a

customized product as per the filter dimensions of AHUs. Unit shall be

monobloc structured type unit specifically designed for integration in Return

Air path to centrally capture and kill germs. It shall be three working principles.

Units shall be US patented technology. Unit shall be suitable for the air

quantity similar to AHUs. It should have pre-filter, polarizer grid, e-filter, run

hour meter, clogging indicator light for filters. CAC shall be suitable for

operation on 220±6 % volts, 50 Hz,1 phase AC power supply.

It should be effective in reducing particles down to 0.01 microns in size.

Pressure drop should not be more than 5mmWG. The e-filter/collector should

be washable type and should have minimum life of 7 years without any

In filter assembly Activated carbon filters to be provided for removal of TVOCs

& CO. Pressure drop should not be more than 3mmWG.

Vendor to study local ambient air data and quality of air before proposing &

finalizing air cleaner. Unit should be suitable to meet all IAQ parameters i.e.

PM 2.5, PM-10 etc. as per standards

Technical submittals with supported catalog shall be submitted for approval

prior to procurement. Quoted price shall be inclusive of all necessary

arrangement as required for fixing of filter section within AHU and control

A. Central Air Cleaners complete with carbon filters

2.0 INDOOR AIR QUALITY MONITOR

Supply, Installation, Testing & commissioning of IAQ Monitor to measure the

levels of PM 2.5, VOCs, CO2, Temperature, Humidity on a real time basis. The

IAQ Monitor shall be RS485 enabled and should be capable of getting

connected with Wi-Fi. Units should have dedicated data browse i.e. sim card

etc. The Monitor should be capable of sending the indoor air quality

information on display Screen/Mobile/Workstation as per Client's

requirement. The Monitor should indicate the quality of air through changing

the colours as per the NAAQS standards and should meet the WELL building

standards. Quoted price shall be inclusive of all necessary arrangement as

required to make the unit proper functional. (LED Screen not included.)

TOTAL ITEM NO. 1 (EQUIPMENT) Rs. ₹ 575,500.00

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

HVAC SYSTEM FOR OFFICE AREA

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

SECTION 'A' : LOW SIDE HVAC WORKS FOR OFFICE SPACES

1.1 INLINE FANS - ACOUSTICALLY LINED

Supply, Installation, Testing & Commissioning of inline fans

for exhaust air complete with sheet metal casing, 25mm thick

acoustic insulation, direct driven centrifugal fan, motor with

proper protection and inspection door. Fan shall be suitable

for operation on 220+6 % volts, 50 Hz,1 phase AC power

supply. Flanges to be provided on both sides to facilitate duct

connections. Fan shall be installed as shown in the drawings

and will be of following characteristics :

All single phase inline fans shall be provided with factory

fitted speed regulators. All Fans Should be complete with

Plug Top & necessary power cable.

Fans shall have low noise level in rage of 35-40dBA @3m and

shall be suitable for indoor installations.

Fan Capacity S.P Area to

No. (Cfm) (mmWG) to be exhausted

TOTAL ITEM NO. 1 (EQUIPMENT) Rs. ₹ 270,000.00 ₹ -

2.0 DUCTWORK/AIR TERMINALS

2.1 FACTORY FABRICATED DUCTING

Supply,Installation, balancing and commissioning of

fabricated at site GSS sheet metal ducts (rectangular/round

ducting complete with neoprene rubber gaskets, elbows,

splitter,vanes, hangers, Gripple supportsetc.) in accordance

with the approved shop drawings and specifications , and

shall also confirm to the BIS specifications.The duct shall be

fabricated at site for to suit pieces.

cases i.e GI rods with GI "C" channels & Gripple Wire Rope

Hanger support . In case of Gripple Wire Rope Hanger

support for duct sizes above 1800mm, MS angles duly painted

with black enamel paint should be used along with neoprene

pad in between the duct & MS angle. All duct support to be

provided with check nuts (lock nuts).

While selecting the duct supports vendor shall ensure

vibration free installation.Quoted price shall be inclusive of

smoke test using smoke bombs.

2.2 SITE FABRICATED DUCTING

Supply,Fabrication , Installation and testing of sheet metal

ducts in accordance with the approved shop drawings and

specifications , and shall also confirm to the BIS

specifications.The duct shall be fabricated at site for to suit

2.3 FLAT OVAL SPIRAL DUCT

Supply, Installation and Testing of factory fabricated & factory

internally insulated GSS (class VIII-120GSM Zinc Coaing) flat

oval spiral ducting complete with vanes, splitter dampers, fire

retardant gaskets hanging arrangement including fully threaded

GI rods , GI straps and GI "C" channels/ rolled steel wires

or Gripple Wire Rope Hangers & Supports

complete with end fixing, GI "C" channels etc. as approved

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

clients/consultants in accordance with the approved shop

drawings and specifications. Quoted price shall be

inclusive of necessary scaffolding charges towards

installation of supply/exhaust air ducts outside

or within building wherever required.

Insulation material shall be 9mm/13mm thick, food grade

material, with antimicrobial properties, Class "O" closed cell

elastomeric insulation material.

Ducts shall be factory powder coated of colour and

shade as approved by the Architects for exposed spiral

ducts. Quoted price shall be inclusive of powder coating.

Necessary compliance to be submitted by vendors.

Without Powder Coated-With 9mm thick insulation

Without Powder Coated-With 13mm thick insulation

2.5 FLEXIBLE CANVASS CONNECTIONS

Supply, Installation, Testing of 125mm deep antivibration

flexible joints at the outlet of air handling units/ductable split

units//inline fans. Flexible connections shall be constructed

using imported fire retardant fabric with extruded

aluminium frame/flange on both sides of approved make.

2.6 LINEAR SUPPLY AIR GRILLES WITH COLLAR DAMPER

Supply, Installation , Testing and Balancing of one way

blow linear supply cum return air grilles complete with

fixed core as per approved shop drawings and

specifications.

Powder coatedThe grilles shall

aluminium be ofof approved

grilles extruded colour & with

integral flanges on both sides & ends as required complete

with corner pieces.

2.6.1 LINEAR RETURN AIR GRILLES WITHOUT COLLAR DAMPER

Supply, Installation , Testing and Balancing of one way

blow linear supply cum return air grilles complete with

fixed core as per approved shop drawings and

specifications.

Powder coatedThe grilles shall

aluminium be ofof approved

grilles extruded colour & with

integral flanges on both sides & ends as required complete

with corner pieces.

2.7 DOUBLE LOUVERED GRILLES

Supply, Installation ,Testing and Balancing of double

louvered supply air grilles as per approved shop drawings

and specifications complete with key operated aluminium

volume control dampers.

a. Powder coated extruded aluminium grilles. SqM 2 ₹ 10,500.00 ₹ 21,000.00 ₹ -

2.8 AIR TRANSFER GRILLES

Supply, Installation and Testing of of extruded

aluminium powder coated air transfer grilles to be

2.9 ROUND DIFFUSERS

Supply, Installation, Testing and Balancing of round

supply air diffusers with removable key operated butterfly

volume control dampers as per the approved shop drawings

and specifications.The diffusers shall be anti-smudge flush

type as approved by the interior designer. Diffuser shall be

complete with GI cone with circular connection at the rear.

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

Powder coated extruded aluminium diffusers of approved

colour & shade suitable for fixing in exposed duct or in

grid/gypsum ceiling as per approved shop drawing.

2.9.1 With Volume Control Dampers

a. 300mm dia Neck Size round diffuser with GI cone No 2 ₹ 3,200.00 ₹ 6,400.00 ₹ -

b. 200mm dia Neck Size round diffuser with GI cone No 25 ₹ 2,800.00 ₹ 70,000.00 ₹ -

2.9.2 Without Volume Control Dampers

a. 300mm dia Neck Size round diffuser with GI cone No -

b. 200mm dia Neck Size round diffuser with GI cone No 2 ₹ 2,600.00 ₹ 5,200.00 ₹ -

2.10 SUPPLY AIR DIFFUSERS

2.10.1 Supply, Installation, Testing and Balancing of square supply

air diffusers with removable key operated volume control

dampers with opposed blades as per the approved shop

drawings and specifications.The diffusers shall be anti-

smudge ring type/flat type as approved by the interior

designer. Diffusers shall be with removable core for the

following neck sizes. The diffusers shall be suitable for fixing

in the gypsum/grid ceiling. The diffusers shall be of regular

type and with outer dimension of 450 x 450mm,

375mmx375mm & 300mmx300mm.

Powder coated extruded aluminium diffusers of approved SqM 105 ₹ 12,184.00 ₹ - ₹ 1,279,320.00 16.17

colour & shade.

2.11 RETURN AIR DIFFUSERS

Supply, Installation,Testing and Balancing of square return

air diffusers same as supply air diffusers but without volume

control dampers as per the approved shop drawings and

specifications. The diffusers shall be anti -smudge ring type.

Powder coated extruded aluminium diffusers of approved SqM 95 ₹ 8,121.00 ₹ - ₹ 771,495.00 16.18

Supply, Installation, Testing and Balancing of linear slot

diffusers with Hit & Miss type extruded aluminium volume

control dampers at supply air outlets as per the approved

shop drawings and specifications.

3 slot/2slot, powder coated extruded aluminium diffusers of

approved colour & shade for supply air with Hit & Miss type SqM

Supply, Fabrication, Installation and testing of Al. Flexible

ducts in accordance with the approved shop floor drawings

and specifications and shall also confirm to the BIS

specifications.

Duct should confirm to fire rating standards BS-476 part 5, 6

Flexible Ducts of following sizes as per approved shop

drawings, specifications :

Supply, Installation and Testing of GI box type volume

control dampers complete with neoprene rubber gaskets,

nuts, bolts, screws, linkages, flanges etc. as per the

specifications and shop drawings.- For Rectangular Duct

2.17 Supply, Installation and Testing of GI box type

volume control dampers as per the specifications

and shop drawings.- For Flat Oval Ducts SqM 2 ₹ 9,800.00 ₹ 19,600.00 ₹ -

2.19 Supply, Installation,Testing and Commissioning

of motorised fire dampers suitable for at least

120 minutes fire rating as per the specifications

and approved shop drawings. Quoted price shall

be inclusive of copper control wiring as required.

Fire dampers shall be provided with 450 mm sleeves

suitable for the wall mounting, (Sleeve Thickness -1.2mm)

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

b. Spring return action type actuator complete with

control panel and temperature sensor. Torque not less No 35 ₹ 9,948.00 ₹ - ₹ 348,180.00 16.20.2

2.20 Supply, Installation and Testing of fresh air

grilles of powder coated / anodised extruded

aluminium with GI wire mesh, inlet louvers,

Box type VCD & bird screen, as per the approved

shop drawings and specifications. SqM 1 ₹ 9,800.00 ₹ 9,800.00 ₹ -

2.22 Supply, Installation and Testing of Bird Screens with GI

wire mesh to be installed at the suction of fresh air/discharge

of Exhaust air as per the specifications and shop drawings.

Sample of bird screen to be got approved from consultants

and Clients prior to procurement. SqM 1 ₹ 6,500.00 ₹ 6,500.00 ₹ -

2.23 Supply, Installation and Testing of non return dampers.

NRDs to be installed in the ducts as per

the specifications and shop drawings.

Sample of NRDs to be got approved from consultants

and Clients prior to procurement. SqM 2 ₹ 7,500.00 ₹ 15,000.00 ₹ -

2.25 Motorised VCD

Supply, Installation and Testing of multiblade box type

zero leakage extruded aluminium dampers to be installed on

AHU Room walls with suitable links, levers and quadrants

for manual control of volume of air flow and for proper

balancing of the air distribution system as per the approved

shop drawing and specifications. 16.14.1

Supply and fixing of actuators of suitable rating of torque

complete with, conrtrol panel, transformer, copper wiring

from the junction box and actuator associated with the above

Actuator shall be suitable for Damper size as shown in the

drawing with minimum 16NM torque. 16.14.2

Actuator should be provided with provision of interlocking

arrangement with PLC Panels for ON/OFF as per CO2 Sensor

TOTAL ITEM NO.2 (Ducting & Air Terminals) Rs. ₹ 662,650.00 ₹ 8,323,105.00

3.0 INSULATION

3.1 ACOUSTIC LINING OF DUCTS

3.1.2 Using Fibre Glass

Supply and Application of internal acoustic lining of

supply/ return air ducting using resin bonded fibre glass

insulation of density not less than 32Kg/CuM as per the

approved shop drawings and specifications. Quoted price

shall be inclusive of GSS channel, metal screws, washers, fibre

glass tissue, perforated aluminium sheet of 24G etc. as

3.2 THERMAL INSULATION OF DUCTS

(Using aluminium foil faced Class 'O' Fire Retardant

Properties Closed Cell Elastomeric insulation)

Supplying and fixing of following thickness duly laminated

aluminum foil of mat finish closed cell Nitrile rubber (Class "O")

insulation on existing duct after applying suitable adhesive for

Nitrile rubber. The joints shall be sealed with 50 mm wide and 3

mm thick self adhesive nitrile rubber tape insulation complete as

per specifications and as required.

TOTAL ITEM NO. 3 (INSULATION) Rs. ₹ - ₹ 3,106,100.00

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

SECTION 'B' - VRV SYSTEM FOR CRITICAL AREAS

1.1 VARIABLE REFRIGERANT VOLUME SYSTEM

Supply, Installation, Testing and Commissioning of Variable

Refrigerant Volume type multi unit air-conditioning system

complete with indoor and outdoor units with individual

controller for cooling & heating application as per the

specifications and drawings. The quoted price should include

clearances charges, local taxes, freight etc. Quoted price shall

also be inclusive of loading, unloading, lifting & shifting of

outdoor units at same floor level or terrace or any other

suitable location as per drawing, positioning charges besides

including charges towards structural steel supports, MS base

frame duly painted & vibration isolation arrangement etc.

1.1.1 OUTDOOR UNITS- HEAT PUMPS

Supply, Installation, Testing & Commissioning of modular

typeVariable Refrigerant Flow/Variable Refrigerant Volume

aircooled Outdoor units suitable for cooling and heating,

having all hermetically sealed inverter type Scroll

Compressor(s), minimum two compressors for above 14HP

modules, microprocessorbased Controller, top discharge type

condensingunit(s), with R410A Refrigerant, vibrationisolators,

with suitable foundation etc. complete as required. The units

hall deliver the ratedcapacity at AHRI Conditions and

workevenat 50°C ambient temperature with out tripping.The

units hall be suitable to work on 400V+/-10%, 3Phase, 50Hz

AC power supply.The unit shall be filled with first charge of

the refrigerant and ready for use as required. The COP at

1.1.2 INDOOR UNITS

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable

media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain

pump, grill, necessary supports, vibration isolation, cord less

remote control etc., suitable for operation on

single phase 230 V ± 10%, 50Hz AC supply, complete, as

required. The unit shall have automatic force shut down

provision in case of fire on receiving signal from BMS System.

The cooling capacity of indoor unit will be at air inlet

Supply, installation, testing and commissioning of following

minimum capacity VRV/VRF High wall type Indoor unit

equipped with washable synthetic media pre-filter, fan

section with low noise

fan/dynamically balanced blower, multispeed motor, coil

section with DX copper coil, electronic expansion valve, outer

cabinet, cord less remote control, drain pan, necessary

accessories etc., suitable for operation on 230 V ± 10%, 50 Hz,

single phase AC supply, complete as required. The unit shall

have automatic force shut down provision in case of fire on

2.0 TR signal from BMS System. The cooling capacity of No. 14 ₹ 22,100.00 ₹ - ₹ 309,400.00

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

Supply, installation, testing and commissioning of following

minimum capacity and external static pressure VRF/VRV

mounted ductable type Indoor unit equipped with washable

synthetic media pre-filter, fan section with low noise

fan/dynamically balanced blower, multispeed motor, coil

with DX copper coil, electronic expansion valve, corded

control, outer cabinet, vibration isolators, drain pan, other

supports etc., suitable for operation on single phase AC

1.2 REMOTE CONTROLS

Supply of Corded remote controls for the above indoor

1.3 CENTRALISED CONTROLLER

Supply, Installation, Testing and Commissioning of main

Intelligent Touch Manager with plus adapter as per

specifications to hook up indoor units as mentioned above.

Controller shall however, be suitable for minimum 48 groups

of indoor units.Centralised controller shall act as master

controller for controlling of cooling mode of outdoor units

and their associated indoor units. Controller shall be suitable

of Remote Access with computer and shall have web access.

Controller shall be suitable to autosequence the outdoor as

well as indoor units catering to 24x7 operated areas as

required/mentioned under sub head "System Design" of

tender document. Controller shall be suitable to configured

the inside temperature as per temperature set point on

controller. Controller shall have time schedulling

arrangement for Indoor Units as well as Outdoor Units.

Controller shall be BMS Compatible & suitable for BMS

Quoted price shall be inclusive of all necessary cabling as

required from ODU & IDUs to controller.

1.4 DRAIN PUMP

Supply, Installation, Testing & Commissioning of Condensate

Drain Pump with adequate Sump for Hi-wall units

complete with water level sensor and accessories as

required. Quoted price shall be inclusive of controller,

NRVs & water sensors and associated wiring etc. to

make installation complete. Drain Pump shall be suitable

for operation on 220+6 % volts 50 Hz, 1phase

AC power supply.

Drain pumps shall automatically ON/Off based on

a. Drain pump for Hi-wall units Nos. 14 ₹ 7,400.00 ₹ 103,600.00 ₹ -

Supply & Installation of GI Drain tray duly insulated with

13mm thick closed cell elastomeric insulation with class 'O'

fire retardant properties below Hi wall Split Units in

Tecchnical Spaces.

Trays to be provided below Hi wall units coming over panels

or other Equipments.

TOTAL Drain tray 1to(EQUIPMENT)

ITEM NO. be connected with drain Rs. ₹ 341,800.00 ₹ 2,731,077.00

2.1 COPPER REFRIGERANT PIPING

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal

sizes of soft/hard drawn copper refrigerant piping for

VRV/VRF system, complete with fittings, with suitable

adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O

tubularinsulation/with Class-O closed cell elastometric nitrile

rubber tubular sleeves sections of specified thickness as given

below for Suction and Liquidlines, all accessories as per

Internal Refrigerant piping in exposed ceiling area & external

refrigerant piping shall be laid on Ladder type cable trays.

Cable trays used for external refrigerant piping shall be

covered with GI cover.

Pipe Size Thickness of CSE

(O.D.) Insulation

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

with 19 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

with 19 mm thick insulation 130

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

with 19 mm thick insulation 90

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

with 19 mm thick insulation 165 ₹ 588.00

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm

with 19 mm thick insulation 130

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm

with 19 mm thick insulation 70

25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm

with 19 mm thick insulation

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.62

mm with 19 mm thick insulation 155 ₹ 1,108.00

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm

with 19 mm thick insulation

41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62

mm with 19 mm thick insulation

NOTE:-1)The Copper Piping & Piping Circuits hould be with

Minimum Number of joints, which shall be attained by : (i)

Using One End Expanded Tubes (ii) Bending the tubes instead

of using elbow joints wherever 90 degree bending is

required.(2)Pipingshouldberoutedatsiteinsuchamanner,thatbr

azedjointsintherefrigerationpipingare kept to a minimum.(3)

The makes of tube fittings shall be same as that of tubes.(4)

The thickness of fittings used shall be same as that of the pipe.

Supply, Installation,Testing & Commissioning of following

imported copper fittings to be provided in

refrigerant pipe line.

a. Refnet Joints (Y- Joints) No 40 ₹ 4,200.00 ₹ 168,000.00 ₹ -

2.3 CONDENSATE DRAIN PIPING-GI

Supply, Installation , Testing and Commissioning of GI

medium class (Class 'B') pipes cut to requird lengths and

installed with all screwed joints for condensate drain.

Quoted price shall be inclusive of supply and fixing in

position the necessary fittings like elbows, tees reducers

etc., and supporting arrangement in accordance with the

approved shop drawings and specifications.Pipes shall be

insulated with 9mm thick closed cell elastomeric insulation

with class 'O' fire retardant properties in tubing form . Pipes

shall be of following sizes :

2.4 CONDENSATE DRAIN PIPING -cPVC

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

Supply, Installation, Testing and Commissioning of CPVC

pipes cut to required lengths and installed for condensate

drain. Quoted price shall be inclusive of supply and fixing in

position the necessary fittings like elbows, tees reducers

etc., and supporting arrangement in accordance with the

approved shop drawings and specifications. Pipes shall be

insulated with 9mm thick closed cell elastomeric insulation

with class 'O' fire retardant properties in tubing form . Pipes

shall be of following sizes :

TOTAL ITEM NO. 2 (PIPING) Rs. ₹ 360,750.00 ₹ 635,895.00

3.0 ELECTRICAL WORKS

3.1 PANELS-For VRV System Shall be covered in main electrical package

Supply, Installation, Testing and Commissioning of the

following cubical type panels made out of 14 gauge CRCA

structure, base channel, complete with, moulded case circuit

breakers, meters, indicating lamps, current transformer etc.

Complete in all respects, insulated bus bars with heat

shrinkable PVC sleeve in suitable bus chambers ,

interconnection, small wiring, name plate, danger plate,

earth bus etc. & comprising of compartments with hinged

door for each feeder & its accessories, cable alley with hinged

doors, bus chamber with bolted door etc. The panel being of

dust & vermin proof construction with rubber gasket

attractively powder coating etc. The panel shall be free

standing type / wall mounted type having IP-65 Protection

suitable for outdoor installation as per relevant drawing

and comprising with the following:

1. All MCCBs shall be with operating handle.

2. CTs burden shall be 15VA & accuracy class 1.0

3. CTs shall be cast resin type .

4. All MCCBs shall be with thermal magnetic

5. All indication lights shall be LED type.

6. All meter shall be digital type.

7. The outgoing starter feeders for pumps, AHUS

& ventilation fans shall be provided

with push buttons & indicating lamps for

status indication.

8. Proper isolation switches to be

provided near air handling units and

ventilation fans in weather proof enclosure.

9. Bimetal overload relay for all the

starters shall have built-in single

phasing prevention feature.

10. Electrical interlocking wiring shall be

provided as per system requirement.

11. Power cabling/wiring with necessary

earthing from source to each panel

and each exhaust fan shall be

provided by other agencies.

i. Incoming power supply shall be provided by main

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

electrical contractor/electrical consultant at each VRV

outdoor unit along with a TPN MCCB and earthing.

3.2 CONTROL & TRANSMISSION WIRING

Supply, laying, affecting connections and

Testing of the following sizes of control

cum transmission wiring to be laid in MS

conduits between indoor units and outdoor

2C x1.5 Sqmm copper wiring RM 500 ₹ 190.00 ₹ 95,000.00 ₹ -

3.3 CONTROLLER WIRING

Supply, laying, affecting connections and

Testing of the following sizes of control

cum transmission wiring to be laid in MS

conduits between indoor units and their wired

2C x1.5 Sqmm copper wiring RM 250 ₹ 190.00 ₹ 47,500.00 ₹ -

3.4 Supply, Installation & Testing of TPN

isolator in weather proof enclosure near

VRV ODUs. No -

IR DISTRIBUTION) Rs. TOTAL ITEM NO. 3 (ELECTRICAL) Rs. ₹ 142,500.00 ₹ -

SECTION 'C' - VAV BOXES & VFDs

1.1 VARIABLE FREQUENCY DRIVES

Supply, Installation,Testing and Commissioning of variable

frequency drives for following Air Handling Units.Variable

frequency drives shall be provided with necessary sensors

and transmitters complete with control wiring in all respect

as required and as per specifications. VFDs shall have built-in

harmonic filters. The drives shall be suitable for the following

motor rating. VFDs shall be housed in precoated, vandal

proof enclosure with On/Off Push Buttons, Phase indication

lights, A/M Switch and with adequate provisions for

ventilation using a fan. The VFDs shall be able to receive the

signals from multiple/combination of duct static pressure

sensors/Temp. sensors and to ramp the speed of the

motor.VFDs shall be suitable to take feed back and

conectivity from all the DPS as mentioned below against each

motor rating to facilitate averaging activity by VFD. Quoted

price shall be inclusive of necessary electrical switches

including change over switch & copper cabling for integration

with the AHU panel. VFD panel shall be installed adjoining

AHU panels for existing AHUs. Overall protection of VFDs with

Panels shall be IP-54.VFDs shall be installed within Electrical

panels as described under Section 'Electrical Works' for New

(i) Sensing Range : 10mm to 50 mm WG

(ii) Output Signal : 4 mA to 20 mA

(VFDs for main AHUs shall be as existing or shall be provided

1.2 VAV BOXES-BY PASS TYPE

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

Supply Installation,Testing and Commissioning of By Pass

type variable air volume boxes complete with necessary

controllers, Heating-Cooling digital thermostat, Damper

actuator, sensor and copper control wiring and necessary

transformer etc. as required and as per the specifications.

VAV Boxes should be suitable to working on Cooling &

Heating mode as per requirement.

VAV Box shall be of following design parameters :

VAV No. Maximum Capacity Location

1.3 ON Line type VAV BOXES - Rectangular type

Supply Installation, Testing and Commissioning of On Line

type variable air volume boxes complete with necessary

controllers, Heating-Cooling digital thermostat, Damper

actuator, multi point pick-up inlet Air Flow velocity sensor

and copper control wiring and necessary transformer etc. as

required and as per the specifications. VAV Boxes should be

BMS compatible. VAV Boxes should be suitable to working on

Cooling & Heating mode as per requirement. VAV Box shall

be of following design parameters :

Max. Air Qty. Min. Air Qty. Location

h. From 3525 to 4000 From 350 to 400 As shown on Drg. No 0 ₹ 35,000.00 ₹ - ₹ -

1.4 DUCT PRESSURE SENSORS

Supply, Installation and Testing of pressure

sensors to be installed in supply air ducts. Quoted

price shall be inclusive of necessary conduting,

copper control cabling from the sensors to the

respective VFDs as per "Approved Shop Drawings". No 3 ₹ 17,500.00 ₹ 52,500.00 ₹ -

Notes: Make shall be same as VAV Boxes make.

TOTAL -VAVs & VFDs Rs. ₹ 3,448,500.00 ₹ -

SECTION 'D' - ACOUSTIC LINING FOR AHU ROOMs

1.1 ACOUSTIC LINING OF AHU ROOMS

Using Fibre Glass

(For repairing of existing Acoustic Lining)

Supply and Application of acoustic/ thermal lining of walls/

ceiling of AHU rooms using resin bonded fibre glass

insulation of density not less than 32Kg/CuM as per the

approved shop drawings and specifications. Quoted price

shall be inclusive of GSS channel, metal screws, washers, fibre

glass tissue, perforated aluminium sheet of 24G etc. as

required for complete installation.

TOTAL - ACOUSTIC LINING Rs. ₹ - ₹ 61,450.00

SECTION 'E' - CO2 SENSORS

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

Supply, Fixing and Testing of CO2 Sensors with Display.

Sensors should be capable to give command to BMS or PLC

panel directly after increasing of CO2 level beyond certain

specified levels. Quoted price shall be inclusive of Power

cabling as required between BMS Controllers/PLCs & sensors

etc. Price shall also be inclusive of all accessories required to

make installation complete whether specified or not. CO2

sensors to be integrated with BMS or PLC Panel by the

2.0 PLC PANEL FOR CO2 SENSORS

Supply, Installation, Testing and Commissioning of

Programme Logic Controller (PLC) with necessary logic for

CO2 detectors and control of Motorised Damper installed in

AHU Room based on CO2 sensing & CO2 level. The panel shall

be installed in AHU Rooms or other specified locations as per

approved shop drawing. PLC should be able to automatically Set 3 ₹ 75,000.00 ₹ 225,000.00 ₹ -

switch ON/OFF the Motorised Damper after

increasing/control of CO2 level beyond certain specified

levels respectively. Price shall also be inclusive of all Power

cabling, control cabling and accessories required to make

installation complete whether specified or not.

SECTION 'F' -CHW BASED SYTEM FOR SHORTFALL

1.1 CHILLED WATER BASED CASSETTE UNITS

Supply, Installation , Testing and Commissioning of

chilled water cassette units each comprising of

following as per the specifications :

Fan section complete with forward curved centrifugal

blowers housed in pre painted GI casing , FHP motor,

3 rows deep chilled water coil, insulated

condensate drain pan, coil piping connections

using necessary copper piping, condensate drain

connections, copper wiring, washable aluminium

mesh multilayer filters etc., high efficiency drain

pump, in built thermostat, decorative panel, drain pump

failure alarm, 3 fan speed control etc.

Unit should be suitable for working on heating & cooling mode.

Units shall be suitable to operate on 220+10%V,50Hz,

1 phase AC power supply and shall be of following

nominal capacity :

e. 2.1TR/860 Cfm - ceiling cassette type unit with remote control. No 2 ₹ 48,000.00 ₹ 96,000.00 ₹ -

f. 1.75TR/750 Cfm - ceiling cassette type unit with remote control. No 2 ₹ 46,500.00 ₹ 93,000.00 ₹ -

1.2 Ceiling Suspended type AHUs - with Thermal Break Profile and Mixing Chamber

Supply, Installation, Testing and Commissioning

of double skin air handling units (AHUs)

each comprising of following as per the

specifications :

a. Casing of air handling units shall be in double skin

construction. Inner skin shall be constructed out of

24 gauge plain GS sheet & outer skin in 24 gauge

pre-plasticized GS sheet sandwitched between

50mm thick injected PU foam insulation of density

not less than 40 Kg /CuM and complete with

inspection doors including control wiring as required.

AHUs shall have access for all parts. AHUs shall be

provided with thermal break profile.

b. Fan section complete with forward curved DIDW

type centrifugal fan/s, IP-55, IE3 TEFC squirrel cage

induction motor suitable to operate on 415+10%V, 50Hz,

3 phase AC power supply and belt drive package.

Fan outlet velocity shall not be more than 1800 FPM (9.2MPS).

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

Fan section should be completed with 25mm thick

Armasound acoustic insulation.

All fans should be AMCA certified.

c. Coil section with multirows deep chilled water

coil of copper tube & copper header and aluminium fins

construction having wall thickness of tubes not less

than 0.5mm. Drain pan shall be made out of 18 gauge

stainless steel duly insulated. Face velocity across

cooling coil shall not exceed 500FPM.

d. Pre-Filter section complete with 50mm thick

washable synthetic fibre filters. Velocity across

the filters shall not exceed 500 FPM.

e. AHUs shall be provided with mixing chamber with R/A & F/A

openings as per approved shop drawing.

f. AHUs shall be complete with suspension arrangement,

it shall also include spring type vibration isolators and

rubber groomets etc. to make the installation totally

vibration free. AHUs shall have separate compartment

for housing of all valves or extended insulated auxiliary

g. Multiblade box type zero leakage manually operated

extruded aluminium volume control dampers shall be

factory fitted at outlet of each AHU.

h. In addition to the above, air handling units shall be

provided with fire retardant flexible canvass connections

made out of canvass sleeve. Sizes of air handling units

shall not exceed as mentioned in the design drawings

and air handling units shall conform to the design

parameters mentioned in specifications.

AHU shall be provided with mixing chamber & thermal break profile.

Provision of installation of EAC System to be provided.

The Air Handling Units (AHUs) shall be of

following duty parameters :

AHU No Capacity S.P Motor Rows of Area to

(TR/Cfm) (mmWG) Rating coil be fed

TOTAL ITEM NO. 1 (EQUIPMENT) Rs. ₹ 1,119,000.00 ₹ -

2.0 PIPING AND VALVES

2.1 INSULATED CHILLED WATER PIPING

Supplying, laying/ fixing, testing and commissioning of

following nominal sizes of chilled water piping inside the

building (with necessary clamps, vibration isolators and

fittings but excluding valves, strainers, gauges etc.) duly

insulated with 80 kg/cum density resin bonded fiber glass or

144 Kg / cum density mineral wool insulation (non

combustible) pipe section insulation covered with a layer of

120 gm/sqm polythene sheet (vapour barrier) and finally

applying 0.63mm aluminium sheet cladding complete with

type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up

to date ) at joints and repairing of damage to building etc. as

per specifications and as required.

Note:The Pipes of sizes 150mm & below shall be M.S. ‘C’ class

as per IS : 1239 and pipes size above 150mm shall be welded

black steel pipe heavy class as per IS:3589, from minimum

6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and

from minimum 7mm thick MS sheet for pipes of 400 mm dia

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

2.3 CONDENSATE DRAIN PIPING -cPVC

Supply, Installation, Testing and Commissioning of cPVC

pipes cut to required lengths and installed for condensate

drain. Quoted price shall be inclusive of supply and fixing in

position the necessary fittings like elbows, tees reducers

etc., and supporting arrangement in accordance with the

approved shop drawings and specifications. Pipes shall be

insulated with 9mm thick closed cell elastomeric insulation

with class 'O' fire retardant properties in tubing form . Pipes

2.4 BUTTERFLY VALVES

Providing and fixing in position the following wafer type

Butterfly Valves complete with SS-410 disc, companion

flanges, nuts, bolts, gaskets etc. as required. Butterfly valves

shall confirm to PN -16 rating as per specifications. Quoted

price shall be inclusive of insulation for valves associated with

chilled water circuit as per the specifications. The valves shall

be following sizes.

c. 40mm dia (Butterfly or Ball Valve) No ₹ 3,501.00 ₹ - ₹ - 16.7.1.8

2.5 GATE VALVES

Supply, Installation , Testing and Commissioning of following

Gate Valves in accordance with the approved shop drawings

and specifications. Quoted price shall be inclusive of

insulation as per the specifications.

2.6 AUTO PURGE VALVES

Supplying , Installaing , Testing and Commissioning

of 10mm dia automatic purge valves. No 8 ₹ 700.00 ₹ 5,600.00 ₹ -

2.7 THERMOMETERS

Supply, Installation, Testing and Commissioning of 100mm

dia dial type thermometers as per the specifications.

2.8 PRESSURE GAUGES

Supply, Installation, Testing and Commissioning of industrial

type pressure gauges completely in stainless stainless steel

(SS) construction with 100mm dia dial and complete with No 16 ₹ 1,500.00 ₹ 24,000.00 ₹ -

shut off gauge cocks etc. as per the specifications.U tube of

pressure gauges shall be insulated.

2.9 MOTORISED BUTTERFLY VALVES

Providing and fixing in position the following Motorised

Butterfly Valves with ON/OFF type actuator of suitable

torque complete with control wiring in copper construction.

Butterfly valves shall conform to PN -16 rating as per

specifications. Quoted price shall be inclusive of current

transformers,control cabling etc. as required, insulation for

valves associated with chilled water circuit as per the

specifications. Valve needs to be interlocked with floor

Mounted AHU Panel provided by the Developer. The valves

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

2.10 BALL VALVES (for FCUs/Cassette Units )- PN 16

Supplying , Installaing, Testing and Commissioning following

ball valves one with Y-strainer and other without strainer

for Cassette units/FCUs. Quoted price shall beinclusive of

2.11 3/2 WAY MOTORISED VALVES (for Cassette/ FCUs )

Supply, Installation, Testing and Commissioning of On-Off

type 2/3 way motorised valves complete with heating-

cooling thermostat, conduiting, copper wiring etc.

Thermostat shall have ON/OFF switch, three speed fan

control, temperature setting arrangement, Heat/cool change

over switch. Thermostat & Valve should be suitable for

operation on 220+6 % volts, 50 Hz,1phase AC power supply.

Valves shall be provided with insulation as required.

2.5 BALANCING VALVES

Supply, Installation , Testing and Commissioning of following

Balancing Valves in accordance with the approved shop

drawings and specifications. Balancing valves shall conform

to PN-16 rating as per the specifications. Quoted price shall

be inclusive of insulation as per the specifications.

2.7 2 WAY DIVERTING VALVES (for AHUs )

Supply, Installation, Testing and Commissioning of motorised

2 way diverting valves with modulating motor, proportional

thermostat and copper control wiring for air handling units.

Quoted price shall be inclusive of current transformers,

control cabling etc. as required and insulation as per

specifications. The valves shall be of the following sizes :

2.9 Y- STRAINER FOR AHUs

Supply, Installation, Testing and Commissioning of following

'Y'- strainers for AHUs as per the specifications having PN-16

rating. Quoted price shall be inclusive of insulation as per the

specifications.

2.12 TEST POINTS (for FCUs/CS AHUs)

Supplying and fixing in position of approved

make Test Points comprising of accessories such

as adaptors, needle etc. Test points shall be in

brass metal construction and comprise of 1/4"

BSP with neoprene sealing bushes and screwed

covers. Test Points shall be installed at inlet and

outlet of each cassette units/ fan coil units. No 8 ₹ 900.00 ₹ 7,200.00 ₹ -

2.13 BMS INTERFACE

Necessary sockets and nipples with shut off valves for

mounting sensors/transmitters on pipe line to interface the Lot --

TOTAL ITEM NO. 2 (PIPING & VALVES) Rs. ₹ 583,100.00 ₹ 1,017,199.00

3.0 INSULATION & ELECTRICAL WORKS

3.1 Insulation & Accousting lining for ducting have been included in Section "A"

Digitally signed by AMIT

IRCTC at New Delhi R0 Low Side HVAC Work

RATE RATE AMOUNT AMOUNT

S. NO ITEM DESCRIPTION UNIT QTY.

Non DSR DSR Non DSR DSR

3.2.2 AHP-1 (Location: Near AHU)

25 Amps ,TP MCCB -- 1set

(0-500) V digital Voltmeter with built in Selector

Digital Ammeter with built in selector

Current Transformers - 1set

LED type RYB phase indication lights- 1set

LED type ON & OFF indication lights -- 1set

3.0/2.0HP DOL starter with built-in single phasing

preventor & overload relay & adjustable timer -- 1 set

START-STOP Push Buttons -- 1 set

Auto-Manual type selector switch

to facilitate auto start of AHUs -- 1set

Provision - VFD/By Pass Selector Switch-- 01Set

Space for VFD Mounting

Ventilation Fan for VFD-- 1Set

Contactors, Potential Free Contacts, Control wiring and

safety circuit as required with start-stop push buttons

stay put or lockable type -1set

3.3.1 Supply, laying, affecting connections and

Testing of the following sizes of 1.1 KV

armoured PVC insulated aluminium

conductor cables. Cables shall be inclusive of

all clamps, saddles, screws, cable identification

tags, cable terminal joints including terminal

lugs, insulating tapes, affecting terminal

connections to the equipment as per the

specifications and as required. Quoted price

shall be inclusive of perforated duly painted

2mm thick MS trays and 8 SWG copper earth

d. 3 C x 2.5 Sqmm cable( Copper Control cabling) RM 5 ₹ 200.00 ₹ 1,000.00 ₹ -

e. 3 C x 1.5 Sqmm cable(Copper Control cabling) RM 120 ₹ 150.00 ₹ 18,000.00 ₹ -

3.3 Supply, Installation & Testing of TPN

isolator in weather proof enclosure near

3.4 Supply and fixing of 1.1 KV grade rubber

mat 914.4 mm wide 6mm thick to withstand

1.1 KV dielectric strength in front of

TOTAL ITEM NO. 3 (INSULATION) Rs. ₹ 240,750.00 ₹ -

Digitally signed by AMIT

IRCTC at New Delhi R0 PAC Works

PRECISION AC SYSTEM WORKS

ITEM DESCRIPTION UNIT QTY. RATE AMOUNT

1.0 DOUBLE SKIN PRECISION PACKAGED UNITS

(With R-410A Refrigerant)-With heater & humidifier

Supply, Installation, Testing and Commissioning

of air cooled double skin precision type packaged

air conditioning units, self contained floor discharge

type complete with scroll compressor/s, fan section

with statically & dynamically balanced centrifugal

backward curved plug type fan driven by

Electronically Commutated (EC) motor having true

soft start characteristics (inrush current lower than

operating current), multirows deep hydrophilic

coated cooling coil with copper tubes and

aluminium fins, remote aircooled condenser/s with

copper tubes and aluminium fins and electronic

expansion valve (EEV). Enclosure shall be in double

skin construction (all sides to be double skin type)

fabricated out of heavy gauge steel

sheet & GI sheet of thickness not less than 1.2mm

with minimum 25mm thick Fibre glass/mineral wool

insulation sandwitched in between. Enclosure shall

be supported on a fabricated steel structure.

The unit shall be equipped with high efficiency

synthetic fibre filters, SS drain pan duly insulated

with 9mm thick Class "O" closed cell insulation,

micro- processor based programmable logic

controller, humidifier, multistage heaters,

thermostat, water detection kit for water

spillage under the flase floor all complete in a unit

as per the specifications. The enclosure shall be

factory painted to a smooth finish. The precision

unit shall also be complete with microprocessor

based electrical panel comprising of indication lights,

Star-Delta/DOL starter, over load protection,

necessary relay to be hooked up with fire & smoke

detection system to facilitate auto trip of PAC and

necessary copper control wiring.

The packaged units shall be complete with auto

sequencing arrangement as required, power loss

alarm, clogged filter alarm and shipped out of

factory with full refrigerant charge. Each unit shall

be provided with BMS integration card & master

card to communicate all relevant data with BMS.

(Applicable in the event BMS is there). The

PAC units shall be suitable for operation on

415+10% volts, 50 Hz three phase AC power

supply. Fan outlet velocity shall not exceed

300 MPM.Quoted price shall be inclusive of MS base

frame duly painted with the black enamel paint for

mounting of remote air cooled condensers and tubular

MS base frame with adjustable legs duly painted for

mounting of indoor unit..

Digitally signed by AMIT

IRCTC at New Delhi R0 PAC Works