SPL REPAIR TO QTR NO 2 1A 2 1B 2 1C 2 1D 2 2D 2 3A 2 3D 07 QTRS AT SUBASH MARG AND UPGRADATION OF TOILET AT 2 SP MARG AND PROVN OF ROOF TREATMENT OF JCO MESS P 160 AT HQ 41 INF BDE AND ROOF TREATMENT AT 17 CARIAPPA UNDER GE EAST LUCKNOW

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness below and above ground level, complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles.complete all as specified and directed.

M&L PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in roof kerbs / benching / coving and roof padding over roof surfaces /sunken treatment etc rounded or chamfered on edges, complete all as specified and directed.

M & L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- (a) 10 mm thick plastering in CM (1:4) using 100 % coarse sand on roof / parapet walls with WPC @ 2 % by weight of cement. (b) Applying a coat of bitumenous primer @ 0.50 Kgs/Sqm on prepared surfaces and allow to dry. (c ) Applying a coat of hot blown bitumen 85/25 grade @ 1.20 Kgs/Sqm over primer. (d) Suply and laying of 3mm thick (Minimum) polymeric water proofing membrane weighing not less than 3 Kgs/Sqm. (e) Applying a tack coat of hot blown bitumen grade 85/25 @ 1.20 Kgs/Sqm. (f) Blinding with dry coarse sand @ 0.50 to 1.0 Kg /Sqm dusted over bitumen. (g) Removing existing felt if any. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.complete all as specified and directed.

Taking down cement plaster or cement lime cement plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for one coat of wall care putty of 1mm thickness after complete removal/newly plastered surfaces of walls and finishing surface even and smooth complete all as specified and directed.

M&L for preparation of putty surfaces in walls by washing, rubbing down and stopping of distempered surfaces and applying two coats of oil emulsion distemper (OBD) over one coat of primer by using roller, of approved shade/tint complete all as specified & directed.

M&L for complete removal of exisiting finish/newly plastered surface (with mechanical sander machine) on walls and applying plaster of paris putty of min 1 mm thickness to prepare the surface even and smooth and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. Note:- Paint to be applied with airless spray machine .

M&L for complete removal of existing treatment and applying three coats of of white wash on ceilling complete all as specified and directed.

M&L for complete removal of existing treatment and applying three coats of of white wash on walls complete all as specified and directed.

M&L for preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth and applying two coats of synthetic enamel paint, complete, all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for vitrified ceramic tiles, light shade,10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per serial item No 14 above but as in dado/skirting etc over 10mm thick rendering in CM 1:4, complete all as specified and as directed.

M&L for non skid coloured ceramic tiles, joint free 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors, incl over 15mm thick screed bed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors complete all as specified and directed.

M&L for glazed ceramic tiles (coloured) 600x300x7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in CM 1:4, complete all as specified and as directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like, over 15mm thick screed bed in cement mortar (1:6) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite and rounding the edges and making holes for gas pipe as required , after demolition of old granite complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even w/o using extra cement complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).complete all as specified and directed.

Forming construction joints 30 mm deep x 10mm wide filled with sealing compound grade "A."complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls. complete all as specified and directed.

S&F in repairs galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.complete all as specified and directed.

S&F in repairs galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.complete all as specified and directed.

S&F in repair viterous china wash down water closet pan (Pedestal pattern) with 'P' or 'S' trap including connection to trap, flushing pipe, anti syphonage pipe and cistern and S& F WC seat cover closed pattern with flat bottom and cover with mild steel chromium plated or aluminised hinging device and finally making good disturbed surface of floor complete all as specified and directed.

S&F in repairs PVC valveless syphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified and directed.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including 40mm bore PVC waste fitting suitable for sink with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink complete all as specified and as directed.

S&F for stainless steel kitchen plate rack of overall size 750 mm x 600 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.63 mm thick fixed with rawl plug and CP steel screws complete all as specified and directed.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete all as specified & directed.

S&F in repairs long body 15mm bore bib tap, fancy type, chromium plated, cast copper alloy, with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed.

S&F in repairs CP angle valve, fancy type long body for 15 mm bore pipe with capstan head long screwed shank including cp cover plate complete all as specified & directed.

S&F in repair 15mm bore fancy type two way CP Brass Bib taps with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed .

S&F in repair chromium plated brass single hole basin mixer with hot and cold arrangement with long shank and cup suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair chromium plated brass wall mixer 2 in 1 (L-bend type) with hot and cold arrangement with cups suitable for 15mm bore pipe complete all as specified and directed.

S&F for 5 mm thick glass Corner shelf 300mm with chromium plated guard, fixed with brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair sheet glass shelf assemble consisting of 5.5 thick sheet glass shelf 12cm wide with CP bracket gaurd & railing 60cm long complete all as specified and directed.

S&F in repair PVC cabinet mirror bathroom box type complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed.

S&F in repair shower health faucet to EWC ,CP brass with minimum 1500mm long CP flexible pipe, connection etc.,complete all as specified and directed.

S&F in repair toilet paper holder, brass chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F in repair Stainless steel soap dish, superior quality, fixed to plugs with chromium plated (CP) brass screws complete all as specified and directed.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks, triple layered (cylindrical, vertical with closed top) hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe incl 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete after dismantling old RCC/PVC tank, complete all as specified and directed.

S&F in repairs 25 mm dia stainless steel curtain rod including brackets and fancy type end knobs, complete all as specified and directed.

Taking down eaves gutters and rain water pipes ( any size or pattern) incl all fittings , shoes, bends, swan neck etc. and removal to store complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75 mm PVC (SWR) floor trap, plain with CP grating, with or without hole including jointing with solvent cement complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend, any radius, complete all as specified and directed.

S&F 100mm PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

S&F 100mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed.

S&F 75mm PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each, complete all as specified and directed.

S&F pressed steel frame for door with one or more rebates size 125x60mm including necessary fixing lugs, lock striking plates, hinges, hold fast etc, incl back filling with PCC 1:3:6 type C1 using 20 mm graded aggregates,complete all as specified and directed.

S&F pressed steel frame for door with one or more rebates size 105x60mm including necessary fixing lugs, lock striking plates, hinges, hold fast etc, incl back filling with PCC 1:3:6 type C1 using 20 mm graded aggregates, complete all as spcefied and directed

S&F 32mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F for 35mm thick factory made glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F PVC cabinet shutter as in Kitchen, Cup board, wardrobe etc with frame of min size 60mm x 44mm including shelves in required sizes at site made out of 18 mm thick one side decorative lamination & other side balancing lamination sheet & provision of shutter made out of 18 mm thick one side decorative laminated PVC sheet all required brackets stainless steel screw etc the panels shell be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish including all necessary fitting as per site requirement and as per make and specification mentioned complete all as specified and directed. Note:- Density of PVC solid sheet should not be less than 575 kg/M3

S&F magnet ball catcher for cup board shutters, complete all as spcefied and directed.

S&F 100mm size stainless steel fancy type handle, complete all as specified and directed.

S&F 150mm size stainless steel fancy type handle, complete all as specified and directed.

S & F for 100 mm long Hasp & staple, safety type, Stainless steel with mild steel hinges pin including bolt to hinges plate & fixed with screw, complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised having 30 mm width of flaps when open complete all as specified and directed.

S&F auto concealed hinges SS size 103mmx64mmx28mm suitable for cabinet and wardrobe complete all as specified and directed.

S&F PVC solid door frame of size 50x47mm made out of 5m plain coloured sheet reinforced with MS square tube complete all as specified and directed.

S&F for factory made soild PVC profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as infill, with 'C type Gl or 40 x 20 x19 of MS pipe as stiffner & supplying & fixing in frame at site as per pecifications & drawing.complete all as specified and directed.

S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified and directed.

S&F 200 mm long stainless steel tower bolts of extruded section (ISI marked) complete all as specified and directed.

S&F 100mm double legged door stopper of stainless steel with rubber base complete all as specified and directed. by Engr-in-charge.

S&F 300 mm long stainless steel sliding door bolts, fancy type, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F in motice locks of brass, 4 lever, 100 mm size, vertical type complete all as specified and as directed.

S & F M.S. Framed work such as grills grating etc. with ends of bars sholdered and / or riveted into spikes, framed guard bars / railings complete all as specified and directed.

S&F powder coated(min thickness of powder coating 50 micron) anodised aluminum window shutter three track sliding type, section having frame size bottom with outer 92x45.5x1.5mm (section code 20617) , top and side 92x31.75x1.5 (section code 20831) & aluminum section of shutter top and bottom size 40 x 18 x 1.5 ( section code 20736) , interlock size 40 x 18x 1.45 (section code 20737), side/ middle size 40 x18 x1.55, (section code 20738) including necessary joining cleats, glazing clips rubber backing, anodised aluminum snap beading screw, anodised aluminum fitting complete as per site requirtement glazing by using 5mm thick plain sheet glass and ss wiremess of dia 0.36mm and aperture 1.4mm thick complete all as specified and directed. Ref drg no celz/c-td/151 sheet no 1/1 & 2/2 . Note- 1. Glazed shutter glass thickness not less than 5mm and ss wiremess shutter with ss wiremesh as approved by GE is also included. No payment will be made separately. 2. No extra payment will be made for section profiles of higher sizes.

S&F powder coated aluminum ventilator ( louvers) shutter with 3.8 mm thick plain / tinted glass consisting of frame of size 63.5 x 44 and shutter sections weighing not less than 0.55 kg/m with locking arrangement as approved fixed including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings with stainless steel wiremesh of 0.36mm including necessary fixing arrangement complete all as specified and directed

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed..

M & L Preparation of new steel or iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F for stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with alluminium wire staples, (any welding work required will be included) complete all as specified and directed.

S&F in repair peg set of 6 brass fancy type,min length 600 mm complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Chhajjas, cover slab, shelves and similar articles set in CM 1:6 complete all as specified and directed.

M/L RCC 1:2:4 type B1 (using 20 mm graded aggrigate)as in slab,chajjas,beam etc including demolition of reinforced cement concrete in floors ,beams ,chajjas,landing slab in any position or height and similar suspended works complete, all as specified and directed.

Repair of Chajjas upto 2 stories by completly removing old broken plasters or pieces of concrete and dubbing out with cement mortar 1:4 or by cement concrete 1:2:4 (12.5 mm graded aggregate) incl necessary formworks and scaffoldings upto 2 stories and GI wire netting 0.90 mm dia and 12 mm mesh for propper bonding of concrete/ mortar and finally finishing the surface smooth and even w/o using extra cement and applying the finish matching from the neighbouring areas complete (plan area of chajjas to be measured).

S & F in repair 40mm dia light garde GI Pipe spout in wall, floors complete all as specified and directed.

M & L for cement concrete 1:7:12 Type F-2 using 40mm graded stone/brick aggregate as in foundation filling, mass concrete or sunkun etc complete all as specified and directed.

M & L for sunken treatment of of bath / toilet / WC etc by cleaning and removing all the loose mortar, laitance, dirt, dust etc by chisel hammer wire brush and fixing APP modified polymer membrane (weight not less than 3 kg/sqm) over a coat of bitumen not below 1.2 Kg per Sqm as over a coat of bitumen primer not below than 0.3Kg per Sqm over 15mm thick plaster in CM 1:3 with adding Dr fixit pidilite liquid water proofing solution 200ml per 50Kg of cement at both hozizontal and vertical surface complete all as specified and directed.

Demolition of cement concret in any despription along with tar felt treatment and cement mortar bedding, any description complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of concrete surfaces in cement mortar 1:4, mixed with liquid water proofing compound finished even and smooth without using extra cement . (Liquid water proofing compound to be measured paid separately) complete all as specified and directed.

M&L for water proofing treatment to roof and edges (Vertical or tapered ) etc. in following sequence (i) Properly cleaning and drying the surface. (ii) Applying a coat of bitumen primer 85/25 (VG-40) grade confirming IS702 @ 1.2 Kg /sqm. (iii) laying APP based polymetric membrane minimum weight 3 kg/sqm and minimum 3 mm thick reinforced with polyster non woven fabric(wt not less than 150 gms/sqm) with 100 mm over lap laid on primed surface by sealed and bonded to the surfaces by torchen method (iv) Applying a coat of bitumen primer 85/25 (VG-40) grade confirming IS702 @ 1.2 Kg /sqm over APP Membrane complete all as specified.

M & L for applying Two coats of bitumen based aluminium painting @ 0.10 kg/Sqm each coat on water proofing treatment.complete all as specified and directed

Taking down mud plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed

M&L 15mm thick rendering in (CM) 1:4 on fair surfaces of brick walls finished even and smooth without using extra cement.complete all as specified and directed

M&L 15mm thick rendering in cm 1:6 on other than fair surfaces of brick walls finished even and smooth w/o using extra cement complete all as specified and directed

M&L for Prepration of New/Old surface of wall and applying two coats of acrlic emulsion paint (exterior grade) over 2mm wall care putty white or tinted complete all as specified and directed

M&L for preparation of New/Old plastered surfaces and applying two coat of oil emulsion distemper (OBD) over 2 mm wall care putty on wall/Ceiling, approved shade/tint complete all as specified and directed

Excavating in trenches n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed.

M & L brick work with fly ash bricks, straight or curved on plan exc 6M mean radius, old size brick built in cement mortar 1:6 complete all as specified and as directed.

M&L for hard core broken bricks of gauge n. exc. 63mm, deposited, spread and levelled in layers n. exc. 15cm thick, water and rammed to a true surface complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations filling, sub base and mass concrete filling, etc complete all as specified and directed

M&L for 16 to 18mm thick granite ( of any type ) work (table rubbed and polished ) in steps, jambs, pillars, window -cills, cooking platforms and like pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding of edge laid over 15mm thick screed bed in CM (1:6) including rounding of edge of stone slabs one edge complete all as specified and directed.

S&F powder coated(min thickness of powder coating 50 micron) anodised aluminum window shutter three track sliding type, section having frame size bottom with outer 92x45.5x1.5mm (section code 20617) , top and side 92x31.75x1.5 (section code 20831) & aluminum section of shutter top and bottom size 40 x 18 x 1.5 ( section code 20736) , interlock size 40 x 18x 1.45 (section code 20737), side/ middle size 40 x18 x1.55, (section code 20738) including necessary joining cleats, glazing clips rubber backing, anodised aluminum snap beading screw, anodised aluminum fitting complete as per site requirtement glazing by using 5mm thick plain sheet glass and ss wiremess of dia 0.36mm and aperture 1.4mm thick including powder coated aluminum grills of aperture 75 mm and fixed in frame of window complete all as specified and directed. Ref drg no celz/c-td/151 sheet no 1/1 & 2/2 . Note- 1. Glazed shutter glass thickness not less than 5mm and ss wiremess shutter with ss wiremesh as approved by GE is also included. No payment will be made separately. 2. No extra payment will be made for section profiles of higher sizes.

S&F aluminium anodized door with frame of size 100X44.5X 1.5mm, stile, middle and top rails of size 82X44.5X1.5mm thick and bottom rail of size 114X44.5X1.5mm thick including 5.5mm thick tinted glass panes with all fittings/ fixtures such as cleats, tower bolt, hinges, locking arrangement, pull and push handle of aluminium anodized, hydraulic door closer etc., complete including aluminium and rubber beading complete all as specified and directed

M&L for TMT bars 10 mm dia and over for reinforcement cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, and binding with and incl MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-415 or Fe-500 complete all as specified and directed.

M&L RCC type B-1 (1:2:4) using 20mm graded aggregate in slab supported on wall walls beams and columns in floors roof landings complete all as specified and directed.

M&L for brick work with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab not exceeding 200mm thick complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8mm thick in vertcial surfaces of size exceeding 0.11 Sqm but not excceding 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed.

S&F solid PVC moulded door frame of size 50mm x 47mm made out of 5mm prelam coloured PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet as reinforced with MS square tube and fixing in opening as specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick, (styles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam (Nut Brown colour ) PVC sheet on the front face & 2mm prelam (Nut Brown colur ) PVC sheet on back face, and fixing inthe frame at site as per specification and drawing on page 161 of SSR (Part -II ) 2010 complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 15mm GI water tubing( Concealed type), medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F tubular towel rail, chromium plated brass 20mm dia 'D" type 60cm long between flanges complete all as specified and directed.

S&F Towel rack 20mm dia with brass chromium plated 600mm long fixed as in repair complete all as specified and directed

S&F in repair towel ring 200 mm dia and made out of 8-10 mm dia hollow tubes superior quality complete all as specified and directed.

S&F in repair Glass shelves fancy type 8 to 10 mm thick glass 550 mm long complete all as specified and directed.

S&F 1000 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

S&F in repair ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of 20mm dia and fixed (minimum weight 210 gms) complete all as specified and directed

S&F in repair 20mm bore Gun Metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe fixed complete all as specified and directed.

S & F PVC door frames (single rebated) of size 60mm x 30 mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer intergral skin with suitable metal CSK screw complete all as specified and directed.

S & F factory made solid PVC profile panel door shutter 28mm thick (style) with internal skin as frame and 3 mm thick presuure compact laminate on both sides of approved color as infill with C channel type GI or 40x20x19 mm of MS pipe as stiffener and fixing in frame complete all as specified and directed.

S&F PVC Cupboard with frame and shutter in required sizes at site made out of 18mm thick one side decorative lamination & other side balancing lamination sheet consisting of carcass 18mm thick pvc sheet & all required brackets 5.5screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finishincl all necessary fitting as per site requitment as per make and specification mentioned as per drawing and complete all as specified and directed by Engineer-in-charge on site.

S&F in repair vitreous China, table top, wash hand basin of size 600 mm x 435 mm x 180 mm, fancy type including 32 mm dia waste coupling and waste pipe complete all as specified and directed

S & F in repair vitreous china pedestal pan EWC (Couple Closet Bowl) of size 370 x 640 x 760 mm including UF seat cover, hinges, S trap-220 mm, accessories set etc and vitreous china ware flushing cistern of complete al as specified and directed.

S & F in repairs CP brass center hole mixer for wash basin for mixing hot and cold water screwed down for iron pipe and fixed for 15 mm bore pipe size complete all as specified and directed.

S & F in repairs CP brass telephonic type wall mixer for mixing hot and cold water screwed down for iron pipe and fixed for 15 mm bore pipe size complete all as specified and directed.

S&F CP brass 15mm fancy type telephonic shower rose suitable for connecting with wall mixture with necessary hook fixed as in repair complete all as specified and directed

S&F long body bib cock fancy type 15mm dia chromium plated with crutch butter fly handle,serewed down,screwed for MS pipe or for brass ferrule complete all as specified and directed

S&F in repair Angle valve cast copper alloy with capstan head chromium plated screwed down high pressure with long shanks and fly nuts screwed for 15mm bore pipecomplete complete all as specified and directed.

S&F in repair 75 mm dia CP OH shower rose fancy type with adjustable arrangementfixed as in repair complete all as specified and directed

S&F CP grating doom 100 mm dia chromium plated complete all as specified and directed

S&F, glass corner self assembly, fancy type, made of 6 to 7mm thick toughened glass of size 250x250mm, fixed with CP brackets, complete all as specified and directed

S&F angle valves 15mm bore , cast copper alloy chromium plated with long sunk and cap (Concealed type), screwed down high pressure screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F PVC connection, heavy duty 15mm bore, 45cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F, 32 mm bore Low density PVC flexible pipe for Wash hand basin/sink etc complete all as specified and directed.

S&F CP brass soap dish fancy type all as specified fixed as in repair complete all as specified and directed

S&F health facuat for EWC CP hand hold with flexiable pipe,bracket etc complete set of superior quality complete all as specified and directed

M&L preparation of newly plastered wall surfces and applying three coats of white wash complete all as specified and directed.

M&L two coat of white washing to old / new ceiling surfaces including preparation of surfaces complete all as specified and directed.

M&L two coat of white washing old / newly plastered wall surfaces including preparation of surfaces complete all as specified and directed.

Complete removal of existing old / new wall surfaces and appling two coats of oil bound distemper over a coat of 1mm thick average thick wall putty, complete all as specified and directed.

S&F in repair 15mm dia two way bib taps, cast copper alloy chromium plated fancy type handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

M&L for PCC 1:3:6 type C2 using 40mm graded aggregate for bed concrete to drain pipe packing under hunching for sides for 150mm dia SWG pipe lines completed all as specified and directed.

M&L for SWG drain pipe grade ‘A’ 150mm dia laid in trenches incl jointing in CM 1:3 complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layer not exc. 25 thick complete all as specified and directed.

Removing excavated materials n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed.

Removing existing roof treatment and preparing surfaces to the entire satisfaction of Engr-in Charge /GE including taking down existing plaster,cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc . flushing at junction of parapets complete and removing the same to the places complete all as specified and directed.

Supply only Liquid water proofing compound complete all as spesified and directed.

Waterproof coating: Providing and applying waterproofing treatment to sound, moisture free concrete surface using Nitoproof 600PF manufactured by Fosroc Chemicals India Pvt Ltd. Nitoproof 600PF shall be liquid applied single component pitch free polyurethane coating capable of bridging substrate cracks up to 2 mm. It shall be applied in two coats at coverage rate of 2kg/sqm. The membrane formed shall confirm to following minimum properties: 1) Elongation : >400% as per ASTM D412 2) Tensile Strength : 2.5 N/mm2 as per ASTM D 412 3) Adhesion in-peel test : >50 N as per ASTM C- 836 4) Recovery from 350% elongation : 95% as per ASTM D 412 5) Water Vapour Transmission 2.3mm film: 0.6 g/m2/hr 6) Initial Hardness Shore A : min 60 as per ASTM D 2240 7) Root resistant : protection screed required No geotextile recommended in between layers as it decreases elongation property of material Membrane Termination shall be done 300 mm above floor level. System includes supply, Surface preparation (crack treatment, coving etc), application and termination of coating all complete as per the fosroc methodology.complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends, any radius.complete all as specified and directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing complete all as specified and directed.

Material and labour for one light / fan point controlled by one, one way switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement etc and making good to the disturbed surfaces to match the existing complete all as specified and directed.

Material and labour for one way switch 6 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall/ floor by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick etc and making good to the disturbed surfaces to match the existing complete all as specified and directed. one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp complete all as specified and directed.

All as per serial item No 163 here-in-before but one bell point controlled by one bell push, 06 Amp.complete all as specified and directed.

All as per serial item No 163 here-in-before but one, two way light point controlled by two, two way switches, 06 Amp.complete all as specified and directed.

All as per serial item No 163 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp.complete all as specified and directed.

Material and labour for one way switch 6/16 Amp wiring with 2.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 2.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall/floor by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick etc and making good to the disturbed surfaces to match the existing complete all as specified and directed. one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp.complete all as specified and directed.

S&F Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed

S&F Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed

S&F Socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed

S&F Modular White cover plate with frame,8 module complete all as specified and as directed

S&F Modular White cover plate with frame,3 module complete all as specified and as directed

Supply and fix of recessed mounted LED ceiling light fitting 9 watt, warm white colour, with IP 20 protection comprises of CRCA housing, high efficiency diffuser cover, electronic driver, etc and all accessories pre-wired including connecting up complete all as specified and directed.

Supply and fix ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed.

S&F exhaust fans, plastic body, ac, single phase, 230/240 v of size 200 mm sweep with louver and making connection with twisted copper flexible wire 23/0.076mm complete all as specified and directed.

Supply and fix of AC Modular box including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Material and labour for sub main wiring with 06 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 06 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

Material and labour for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

Supply and fix SPN MCB DB 8 ways with 200 Amps rated bus bar 240Volt, Double door type complete all as specified and directed.

Supply and fixing MCB SPN 32 Amps 240 V, C- curve, 50 Hz, breking capacity-10 kA. complete all as specified and directed.

Supply and fixing MCB SP 6-32 Amps240 V, C- curve, 50 Hz, breking capacity-10 kA . complete all as specified and directed

S&F Modular White cover plate with frame,12 module complete all as specified and as directed

S&F Modular White cover plate with frame,2 module complete all as specified and as directed

S&F Modular Metal flush box 12 module complete all as specified and as directed

S&F Modular Metal flush box 8 module complete all as specified and as directed

S&F Modular Metal flush box 3 module complete all as specified and as directed

S&F Modular Metal flush box 2 module complete all as specified and as directed

S&F Calling bell , AC, 230 Volts, single phase complete all as specified and as directed

S&F bell push , AC, 230 Volts, 2 module complete all as specified and as directed

Supply and fix fan step regulator, 120W 2 module complete all as specified and as directed

Supply and fix in replacement of decorative wall mounting type LED light fitting, 1 x 15 Watt, 230 Volt made up of Polycarbonate including shade, lamp holder, 9/10 Watts LED lamp B22 CDL etc and all accessories pre-wired including connecting up complete all as specified and directed.

Supply and fix in replacement of integrated LED bulk head fitting 10 Watt, 6500K with IP 65 protection comprises of high pressure die cast aluminium housing, polycarbonate cover, etc complete all as specified and directed.

Supply and fix LED tube light fittings 1200 mm,20 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminum housing enviromental friendly, energy efficient complete all as specified and directed.

Supply and fix LED tube light fittings 600 mm, 10 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminum housing enviromental friendly, energy efficient complete all as specified and directed.

Supply & fix LED wall/surface mounted down lighter, 12 W including electrical connection with PVC three core copper flexible wire & all necessary fixing accessories complete all as specified

Taking down carefully ceiling fan of any sweep complete with all accessories, dismantling blades and deposit in safe custody of AGE E/M Yard-II for BER procedure complete all as specified & directed.

Supply and fix in replacement of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix in replacement of sheet metal enclosure distribution board, double door, single pole and neutral, AC, 240 volt, 08 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix in replacement of sheet metal enclosure distribution board triple pole and neutral (VTPN),double door, AC, 440 volt, 04 way with 200 Amp rated copper bus bar and metal door with IP 54 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed and comprising of the following:- (a) MCCB, 125 Amp, 04 pole, AC, 415 Volt of 16 KA breaking capacity complete - 01 No. (b) MCB, SP, AC, 240 volt of 06 to 32 Amp, "C" curve, 10 KA breaking capacity - 12 Nos.

Supply and fix in replacement of MCB, SP, AC, 240 volt of 06 to 40 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, DP, AC, 240 volt of 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.by Engr-in-Charge

S&F of exhaust fan single phase, 230/240 Volt heavy duty of size 300 mm sweep 1400 RPM including suitable louvers and making connection with twisted copper flexible wire 23/0.076mm complete all as specified and directed.

Supply and fixing in replacement LED Bldg security light fitting LED 45 watt with SPD, PF not less or equal 0.9,epoxy coated cover sheet aluminium housing with heat resistant toughtened glass & IP 66 incl with bracket, clamps, nuts, bolts protection complete all as specified and directed and directed.

Cutting walls any type, making holes for fixing of exhaust fan of any size or sweep and making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified and directed

Taking down electric meter and refixing on same board after rewiring complete all as specified and directed

Supply only LED bulb 9/10 Watts suitable for B22 white in colour complete all as specified and directed

M/s Bhadoria Associates (BID ID -3078504)

QUALITY CONSTRUCTIONS CO (BID ID -3079616)