PROVN OF CHAIN LINK FENCING WITH GATE FOR NFS MW AT 164 MTN BDE SIG COY AND PROVN OF 01 STORE ROMM NEAR BLDG P-39 AND PROVN OF FALSE CEILING FOR BLDG NO P-43 MAIN OFFICE OF 1ST BN SIKKIM SCOUTS AND PROVN OF 02 MS GATE OF 23 RAJPUT DALAPCHAND UNDER

Amount

M & L for excavating in post holes (or similar holes) each n exc 0.5 cum , getting out , returning , filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering , and removing surplus soil to a distance n exc 50 m and making good surfaces in hard/dense soil complete all as specified and directed.

Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and not exc 1.50m deep for foundation and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches, n.exc. 1.5m wide and n.exc 1.5 m in depth; for foundation, etc. and getting out in hard/dense soil complete all as specified and directed.

M & L for returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft / loose sioil.felling under floor complete all as specified and directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.50m above the starting point complete all as specified and directed.

M&L broken stone or bounders hardcore of gauge n exc. 63 mm , deposited, spread and levelled in layers n exc. 15 cm thick , watered and rammed to a floor/true surface.

M & L for PCC type D-2 (1:4:8) (using 40mm graded stone agg) in foundation filling and mass concrete complete all as specified and directed.

M & L PCC Type C2 (1:3:6) (40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M & L 75 mm thick PCC type C-2 (1:3:6) using 40 mm graded stone aggregate as in sub base or sub flooring finishing the surface even and rough to receive the topping layer complete all as specified and as directed.

M & L for PCC type C-2, (1:3:6) (using 40 mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for 75 mm thick PCC (1:4:8) Type D2 (using 40 mm graded aggregate) as in sub base complete all as specified and directed.

M&L for 40 mm thick PCC (1:2:4) Type B1 (using 20 mm graded aggregate) as in floor fininsh complete all as specified and directed.

M&L 75 mm thick PCC type C-1, (1:3:6) (20mm graded stone aggt) as in path, plinth protection etc., complete all as specified and as directed.

Forming construction joint (dummy) joints 65mm deepx 10mm wide filled with sealing compound grade A complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M & L chequered cement concrete tiles of size 30cm x 30cm x 25 mm thick ad above, set jointed and pointed in neat slurry with grey cement and pigments in floors cut and polished over and incl 15 mm thick screed bed or bedding layer of mortar for lying floor finishes in cement plaster 1:6 complete all as specified and as directed.

M & L for granite (of any type) 16 to 18 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) over 15 mm th screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and direected.

M & L for RCC (nominal mix) type B-1 (1:2:4) (using 20mm graded stone agg) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed.

M & L for RCC (nominal mix) type B-1 (1:2:4) (using 20mm graded stone agg) for columns, pillars, piers, post and struts complete all as specified and directed.

M & L RCC, (nominal mix) type B-1, (1:2:4) (20mm graded stone aggt) in Beams, cantilevers, bressumm?ers, lintels over 1.5m span and similar works all as directed by EIC.

M & L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M & L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M & L mild steel TMT bars 10mm dia and over cut to length bend to shape required incld cranking bending spirally for hooping for column, hooking ends and binding with and incld mild steel wire (annealed not less than 0.90mm dia or securing with clips complete all as specified and directed.

All as per sl item No-25 above but 6mm to 8mm dia complete all as specified and directed.

All as per sl item No-25 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

S & F galavanised 2 stand steel barbed wire 2.24mm dia barbed with 2mm dia at barbs 75mm spaceing and strainings and fixed to any type of standard rails staning bolts including securing or tying at crossing with provision of GI mid steel pins etc complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standerds, rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Supply only chain link MS galvanised fencing any size or type complete all as specified and directed.

S & F hot-rolled steel unequal/ equal angles embedded in concrete and screwing etc, securing bolts, post and struts in fencing including cutting tops to shape as directed, drilled holes , notching for wire, etc ; flat iron fillets (for securing wire mesh etc.) including all necessary drilling , bolting or riveting , etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, length n exc 6 cm and dia of neck 11 to 15 mm complete all as specified and directed.

M & L mild steel Gd.I. IS-432 (Part I) round bars 10mm dia and over cut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire (annealed not less that 0.90 mm dia or securing with chip) complete all as specified and directed.

M & L for two coat of synthetic enamel paint over priming with Red oxide zinc on new or prevously untreated surface of any description not exc 10 cm in width or girth when unconnected with other painting or painted in different tint complete all as specified and directed.

M&L for two coats of synthetic enamel paint on new surface of steel and iron surfaces any description over 10 cm width or girth over a coat of red oxide primer including prepration of surface all as per specifed.

M & L for preparing new steel surfaces of any description exc 10cm width or grith and applying two coats of black Japan paint complete all as specified and directed.

M & L for framed work such as grills,gratings, gate etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 for portins framed and hung as gates, including pintle hinges, stops hand-made sliding bolts etc. complete all as per specified.

S&F rolled mild steel in framed work/Hollow secton etc as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete drilled for fixing of steel sheeting or other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings of grade Fe 410-W (Gde-E 250) quality B complete all as specified and directed.

M & L mild steel sliding door bolt 300mm long, plate type, stove enamelled black,with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts , four on bolt plate and two on staple and fixed to gate complete all as specified and directed.

Dismantling of wall & celling boards (fiber pulp insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets.

S&F 605 X605 mm GI frame work for for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to sorrounding wall using nylon sleeves and screws at 450 mm centre to centre /intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from suffit at approx 900 mm centre to centre with GI cleats and steel expansion fastner with and including ceiling section (not exc 1.2 m length)of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10 .5 mm fixed to the intermediate channel with connecting clieats across the intermediate channel at 457 mm centre to centre.

S&F 10mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks, exc. 10 cm in width type C-1 (1:3:6) (using 20mm grade stone agg) set in cement mortor (1:6) complete all as specified and directed.

M & L for Damp Proof Course in cement mortar (1:2) , 20 mm thick with using water proofing compound 3% by weight of cement including necessary formwork.

Supply of integral water proofing compound .

M&L 10 mm thick rendering on fair faces of brick work or concrete surface in cement plaster (1:4) on external surfaces of wall finished even and fair complete all as specified and directed.

M&L 10 mm thick rendering on fair faces of brick work or concrete surface in cement plaster (1:6) on internal surfaces of wall finished even and fair complete all as specified and directed.

M & L for preparing new surace, two coats of cement base paint over a coat of alkali resistant primer on external walls incl watering etc complete all as specified and directed.

M & L for preparation new surfaces and applying three coat of white wash on internal walls complete all as specified and directed.

S&F roof trusses, framed trussed, purlins, crane gantries, rails and fastening and heavy brackets framing (Beam, tee, angle channel or flat section) incl distance pieces, cleats, nut and bolts conforming to FE-410w (grade 250-E quality A) complete all as specified and directed.

S & F Pre-painted galvatume aluminium zince coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strenght of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F Pressed steel frames of size 165x60 mm for door with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate etc., complete as specified.

S & F 30mm thick flush door shutters , solid core construction with black board core and plywood face panels,commercial type on both face complete all as specified.

S&F 200mm size aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed.

S & F 150mm size aluminium handle cast type anodised complete all as specified and directed.

S & F 300 mm long aluminium alloy, anodised sliding door bolt with hasp and staple (bolt type ) and fixing clip of sheet cost or extruded section or cost aluminium alloy & fixed

S & F steel windows for glazed with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by EIC.

S&F steel ventilator with top hung shutter fixed type including hinges, steel peg stay, complete complete all as specified and directed.

M & L 4 mm thick sheet glass , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Preparation of new painted steel and iron surfaces of any description and in any position over 10 cm width or girth as in roof not other wise specially described and applying one coat of Ist grade enamel paint over a coate of red oxide primer zinc chrome all as specified and as directed.

Material and labour for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core multi stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC casing and capping not less than 20mm size, medium grade with all necessary fittings, surface wiring , for light /Bell point controlled by one switch including 1.5 Sq mm PVC insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes/ on PVC rectangular block with 3 mm thick plastic laminated sheet cover of suitable size (concealed type in permanent bldg and surface in temporary bldg or as directed ) for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover ,for housing switches, socket outlet, regulator etc. complete all as specified or directed including testing on completion including taking down old point wiring.

All as per item No.63 here-in-before but One 3 pin socket outlet 5/6 Amps on the same board with other switchs with cables 1.5 Sqmm size.

All as per item No.63 here – in – before but for one 3 / 5 -pin switch socket outlet 5/6 amps on independent board.

All as per item No.63 here – in – before but for one switch socket outlet 15/16 Amps on independent board with 2.5 Sqmm multi stranded and 2.5 Sq mm stranded (for earth) PVC insulated un-sheathed copper cable.

Supply and fix switch piano flush button, single pole, 5/6amps, one way all as specified and as directed.

Supply and fixing lamp/angle holder insulated body with back plate for batten fitting all as specified and as directed.

S & F in LED retro fit lamp B-22 holder base with poly carbonate body and aluminium heat shrink of 9W complete CAT Part No : LHLDDBEBBI8R009 of havells or Equivalent of Crompton/Philips.

Supply and fix switch socket combination 2 – in – one, 3 Pin / 5 Pin, 5/6 amps flush type all as specified and as directed.

Supply and fixing switch socket combination 2 – in – one 6 Pin , 6 / 16 amps flush type universal all as specified and as directed.

Supply & Fixing ceiling rose surface bakelite 65 X 50 mm three terminal all as specified and as directed.

Supply and fixing LED tube lights fitting, 4 feet long 1x 18W, 220V, AC decorative box type with holder including Removable poly cabonate LED tube light with inbuilt driver connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S & F LED light fitting 1x9W/1X10W IP66 & IK09 integral LED Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unserviceable fitting complete all as specified and as directed.

Supply and fixing Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 200 Amps rated Single pole and neutral linkof 4 way 240 Volts AC complete all as specified and as directed.

Supply and fixing MCB Single pole and neutral upto 32 Amps capacity 10 KA 240 Volts 50 HZ. conforming to IS/IEC 60898-1 2002, integrated label holder, Sliding bottom clamp, IP 20 protection, complete all as specified and as directed.

Supply and fix MCB/Isolator single pole (SP), 10 kA of 6 Amps to 32 Amps capacity 240 Volts. conforming to IS/IEC 60898-1 2002, integrated label holder, Sliding bottom clamp, IP 20 protection, complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m bellow normal ground level, connected to galvanized earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI med grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC 1 : 3 : 6 type C-1 , 50 mm thick pre cast RCC 1 : 2 : 4 type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar ,GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 5 of MES SSR Part-I and as directed.

Sand cushioning to underground cables provided with a layer of sand 8cm thick before laying the cable in trenches and 15cm thick after laying the cable in trenches complete all as specified.

M&L Sub class ‘B’bricks for covering to cable laid dry flat ,with width equal to the length of brick complete all as specified and directed.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 2 Core, including glands, lugs, nut, bolts, washers as required at site, testing complete all as specified and directed.

S & F Steel pipe glavanized light grade of 40 mm dia laid in trenches or under ground/floor or road of fixed with pole for protection of cable/ Earth sstrip including clams with bolts nuts and wasers complete ass as specifed.

Note: In case doubling/duplicancy of BOQ items , the lowest quoted rate shall be applicable for payment.

MS MAYA PRAKASH GOEL AND SONS (BID ID -3132584)

MANOJ JINDAL (BID ID -3132604)

G K SUTHAR (BID ID -3132689)

SANJAY SAW MILL (BID ID -3131609)

RAJU TAMANG (BID ID -3130744)

M/S JAYSHREE CONCERN (BID ID -3132671)

MS BRAHMA CONSTRUCTION (BID ID -3132702)