86108SPECIAL REPAIR TO BLDG NO P-39 MAIN GYM COMPLEX AT AIPT UNDER GE (CENTRAL) PUNE.

Amount

Dismantling asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings complete all as directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / clading to wall fixed with self taping screws complete all as specified and as directed.

S&F Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / clading to wall fixed with self taping screws complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as directed.

M & L for preparation of old steel surface of any description over 10 cm width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed.

M & L for false ceiling 8mm thick PVC panels (coloured/ designe) including decoratrive cornices/ moulding of pattern as per approved by GE on GI grid frame work consisting grid & GI main tee 32 x 24mm, cross tee 25 x 24 mm and angle of walls of size 20 x 20 mm all made out of 0.50mm GI sheet size of grid not less than 600 x 600mm hung from ceiling using 2mm GI wire suspendors spacers at 1.2 mtr c/c on main runners including making nitches for light, fan decorative / concealed light fittings and fasteners if required complete all as specified directed by Engr-in-Charge.

Taking down Chowkats or frames exc 1.00 sqm but not exc 2.0 Sqm each (without taking off shutters from the frame) complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) etc complete all as directed.

S&F PVC Door frame of size 50mm x 47mm 5mm thick single side prelam PVC sheet reinfirced with M.S Square tube complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of M.S tubes for top & bottem rails. M.S. Frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam PVC colour sheets for top rail, lock rail & bottem rail on either side & as gap insert for top rail & bottem rail, panelling of both sides colour prealm PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & Drawing complete all as specified and as directed.

S & F 100 mm long butt hinges medium weight ,stainless steel for PVC door shutters complete all as specified and as directed.

S&F 200mm aluminium anodized barrel tower bolts of extruded section for door shutters complete all as specified and as directed.

S & F 300 mm long aluminium alloy , anodised sliding door bolt with hasp , staple( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast - aluminium alloy and fixed complete all as specified and as directed.

S & F 150mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed.

M&L for PCC (1:2:4) type B0 25 mm thick (12.5 mm graded aggregate) in floor to receive top layer like tiles etc complete all as specified and as directed.

Taking down cement plaster on brick/ block walling including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L rendering 10 mm thick on block masonry surfaces fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L rendering 15 mm thick on block masonry surfaces other than fair faces of brick work or concrete surfaces in CM 1:4 finished with sponge finish complete all as specified and as directed.

M&L for preparation of newly plaster surface of wall and apply two coat of cement base paint complete all as specified and as directed.

M & L for preparation of new plaster surface of wal and applying two coats of oil bound distemper over 2mm thick wall care putty complete all as specifed and directed.

M&L complete removal of existing treatment and applying two coats of oil bound distemper over 2 mm thk of wall care putty complete all as specified and directed.

M&L complete removal of existing treatment from external walls and applying two coats of weather proof paint (Apex) over one coat of primer complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed.

M & L ( Light shade) Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed.

M & L ( dark shade) Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed.

M&L for coloured Ceramics tiles 300 X600X7 to 8 mm thick in vertical surfaces such as skirting , dado set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick rendering in cement mortar 1:4 on stone / brick/ concrete masonry surfaces complete all as specified and as directed.

M&L Non skid ceramic coloured tiles in flooring 7 to 8 mm thick area of each tile exceeding 0.11 sqm and not exc 0.18 sqm (400x400mm) with joint free tiles set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick cement screed bed in CM 1:6 complete all as specified and as directed.

S&F Aluminum single leaf door on pivots of powder coated frames alongwith hydrulic door closer (Aluminium Extruded section), door lock, handles, 5mm thick tinted glass in top and 12mm thick prelaminated particle board (both side laminated) in bottom panel, fixed with rubber beading and glazing clips and using as given in 'JINDAL' Catalogue complete all as directed by Engineer-in-Charge.

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

Taking up or down steel tubing and connections, including removal to store 15mm dia complete all as specified and as directed.

All as per item No 30 here-in-before but 20mm dia complete all as specified and as directed.

S&F in repairs 15mm dia medium grade galvanised GI pipe with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

All as per item No 32 here-in-before but 20mm dia complete all as specified and as directed.

S&F low density polyethylene pipes (LDPE) 32mm dia of pressure rating 6 Kgs/Cm2 laod fixed complete to walls ceilings or in floors etc complete all as specified and as directed.

All as per item No 34 here-in-before but 40mm dia complete all as specified and as directed.

M&L for granite 16 to18 mm thick (of any type,any colour) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M & L pre polished both side cuddappa stone slab 30 to40 mm thick as in partition/ support for platform fixed in position complete all as specified and as directed.

Rounding to edges of stone slab one side ,such as in steps cooking platform and similar situations complete all as directed.

S&F oval shaped coloured vitreous china WHB table top colonia snow white, fancy type of overall size 595 x 380mm, cat No 7751 of cera or of equivalent as per list of make attached as Appx 'A', lvory coloured, excluding taps waste, chain and plug and porcelain stopper, placed on granite top slab supported on cuddappa stone slab ( Note:- granite slab and cuddappa stone slab shall be measured separately) complete all as specified and as directed.

S&F in repairs 32mm waste fittings, brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in repairs chromium plated pillar cock with 310 mm Extension body Cat No. 29021 of make Jaguar ‘‘Fusion' Quarter Turn Series or equivalent as approved by GE. all as specified and as directed.

S & F in repairs vitreous china squatting Pan " Orissa " pattern of size 580 mm X 440 mm Ivory with integral foot rests ( excluding flushing cistern and flush pipe) including provn of cement concrete bedding complete all as specified and as directed.

S & F in repairs vitreous china wash down water closet pan ( pedestal pattern ), Ivory including connection to drain ( or outgoing pipe ) and to flushing pipe with and including S & F plastic water closet, seat white closed pattern with flat bottom, cover and mild steel hinging device complete all as specified and as directed.

S & F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, including flush pipe 32 mm dia complete all as specified and directed.

S&F vitreous china wall hung wash down water closet, with 'P' trap of size 510x365x380 mm snow white colour including soft close cover , outlet/intel gasket confirming to CAT No S1041106, 'CARNIVAL CLEAN RIM' of cera or of equivalent as per the list of make attached as Appx 'A' specified here-in-after complete all as specified and as directed.

S & F in repair,vitreous china ,full stall type urinal, coloured with urinal censor complete with necessary fittings complete all as specified and as directed. MAKE :- Hindware ,senso Art Cat No 60018 Star white or equivalent as per the list of make attached as Appx 'A'.

S&F in repair 15mm dia Angular stop clock with wall flange cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron unions complete all as specified and directed. (Make : Jaquar Cat No CON-053KN) or equivalent as per the list of make attached as Appx 'A'.

S&F in repairs PVC connection 600cm long 15mm dia, with 2 Nos CP brass check nuts complete all as specified and as directed.

S&F in repairs, brass CP soap dish confirming to Cat No CAN-1131N as mentioned of make "Jaquar" or of equivalent as per the list of make attached as Appx 'A' complete all as specified and as directed.

S&F in repair 15mm dia bib tap of cast copper alloys chromium plated fancy type with fancy handle with wall flange screwed down screwed for iron pipe or for brass complete all as specified and as directed.

S & F in repairs 15 mm chromium plated 2 way bib cock with wall flange confirming to CAT No. F2002161 of " Cera" or of equivalent as per the list of make attached as Appx 'A' complete all as specified and as directed.

S & F in repairs 125 mm dia swivel type brass chromium plated shower rose of approved quality complete all as specified and as directed.

S & F for health faucet including flexible cod confirming to CAT No. ALD-573 as mentioned of make- Jaquar or equivalent as per the list of make attached as Appx 'A' complete all as specified and as directed.

S&F in repair 18 mm thick MDF board prelaminated both side with decorative choice lamination as in Office Cabinet,pelmate box,drawer, CB shutter etc fixed with screw including 6mm thick, 1st Class HW (TW) beading all around on edging to timber frame work all as specified and directed by Engr-in-Charge.

S&F in repair 5 mm thick MDF board prelaminated one side with decorative choice lamination as in Office Cabinet,pelmate box,drawer, CB shutter etc fixed with screw including 6mm thick, 1st Class HW (TW) beading all around on edging to timber frame work all as specified and directed by Engr-in-Charge .

M&L for plain fillets, 2nd class hard wood square rectangular or triangular in section exc 13 & n.ec 25 sqcm, claean sawn, secured with nails or brads complete all as specified and as directed.

S & F in repair 30mm width of flap brass continious (piano) hinges for built in cup board shutter as approved by Engineer-in-Charge.

S&F 125 mm brass fancy type cupboard handles fixed with nuts, screws and washer of brass polished complete all as specified and as directed.

S&F hasp and staple safety type aluminium with steel hinge pin incl bolt to hinge plate and fixed witth screws of 125mm in size complete all as specified and as directed.

S&F Megnetic catcher for cabinets all as specified and directed.

S&F in repairs of aluminium anodised barrel tower bolts of exttruded section 75 mm long complete all as specified and as directed.

Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 (40mm graded stone aggregate ) for using sub base 100mm thick complete all as specified and as directed.

M&L sand filling 50 mm thick as cushion for interlocking tiles including watering and consolidation complete all as specified and as directed.

M&L for precast cement concrete glazed Interlocking tiles 60mm thick in floor/pavement laid over 50mm thick sand cushioning laid dry to the profile including vibrating with surface vibrator after laying of tiles complete all as directed by Engineer-in-Charge. (Note : sand cushion will be measured and paid separately)

M & L for preparation of old wooden surface of any description on 10cm width or girth and applying one coat of synthatic enamal paint complete all as specified and as directed.

Dismantling boarding any description, fixed in any position with nails complete all as directed.

S&F first class hard wood wather boarding clean sawn, thickness 20mm to 25 mm and rebated on thick edge to give 20mm laps complete all as specified and as directed.

M & L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of syntehetic enemal paint over a coat of pink primar complete all as specified and as directed.

M&L spirit polish on old wooden surfaces of any description, over 10 cm in width or girth including preparation of surfaces complete all as specified and as directed.

Removing of existing old bitumenous tarfelt including cement screed bed and clean the surface with wire brush and washing with water to achieve the original surface of slab all as specified and directed.

M & L water proofing treatment to RCC roof slab, walls, chhajjas ets, shall be carried out as specified below and as directed by Engineer-in-Charge including taking down old waterproofing tratement. (a) M&L for 10mm hick plaster screed bed layer in CM 1:3 on concrete surfaces. (b) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying a coatt of approved bitumnous primer @ 0.20kg/Sqm of area complete all as specified. (c) Laying App polymer modified approved membrane, non woven, polyester, weighing not less than 3.5 kg/Sqm and 4mm thick with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engr-in-Charge. Carrying out test by flooding water for 24 hrs for leakagge & seepages and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specifed & as directed by Engr in Charge.

Dismantling wrought rion or mild steel iron of any description not otherwise provide for complete as directed.

S & F Stainless steel (S S) gate/Railling /grill/ Made of stainless steel (Grade -304 -316 corrosion resistance ) with angle, FI,Squre,Bar and similler pipe with ornamental and intricate design. complete all as specified and as directed by Engr-in -Charge

M & L machine Grainding /polishing of existing kota stone flooring with Fine Grade (No. 120) , applying oxalic acid ,wax polish to obtain mirror polish finish all as specified and as directed.

M & L machine Grainding /polishing of existing kota stone skirting with Fine Grade (No. 120) , applying oxalic acid ,wax polish to obtain mirror polish finish all as specified and as directed.

M & L Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete grade Fe-410 W complete all as specified and as directed.

M& L Mild steel sheet 1 mm thk & 150 mm dia eaves gutters, galvanised class 3, half round with rounded edges complete all as specified and as directed.

S&F rotational moulded polythylene water storage tanks (cylinrical vertical with colsed top) hoisted and fixed in postion all as specified and directed of 1000 ltrs capacity complete all as specified and as directed.

S&F in repairs 20 mm ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipe for the following sizes all as specified and directed by the Engineer-in-Charge.

Disconnecting existing water storage tanks of any capacity not exc. 1000 ltrs and setting aside, and refixng in the same position after carryout necessary roof treatment including necessary fittings and GI pipes if required complete all as specified and as directed.(Note:-Necessary arrangement for w/s to be done by the contractor till completion of roof work)

Dismantling of soil waste and vent pipes of cast iron/PVC jointed in cement mortar/lead joints and taking out from position incl cleaning and stacking for reuse of 75/100mm dia including connected fittings complete.

M & L in repairs 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in floors as specified and directed.

M & L in repairs 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in floors as specified and directed.

S&F PVC (SWR) bends plain 110 mm bore complete all as specified and as directed.

S&F PVC (SWR) bends plain 75mm bore complete all as specified and as directed.

S/F PVC (SWR) Branch piece single (single Y) equal or unequl 110mm dia with door access complete all as specified and as directed.

S/F PVC (SWR) Branch piece single (single Y) equal or unequl 75mm dia with door access complete all as specified and as directed.

S&F for 75mm dia SWR junction (single 'T') equal or unequal with door access complete all as specified and as directed.

S&F for 110mm dia SWR junction (single 'T') equal or unequal with except door access.

M&L for 75mm thick PCC (1:3:6) type B2 (using 20mm graded aggregate) as in plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified.

Taking down the existing unserviceable main switch / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down the existing unserviceable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down ceiling fan/ exhaust fan/ wall fans of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and as directed.Note : Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc.

M&L for point wiring of any length using approved colour coding as per IS, with stranded copper conductor 1.5 Sq.mm(Nominal area), single core, PVC insulated and unsheathed stranded FRLS cable 1100 volts grade, ISI - 694 marked in and including heavy duty, PVC casing caping including all accessories etc. heavy duty ISI marked, with ISI marked PVC boxes and accessories suitable for mounting switches/sockets etc, and PVC insulated stranded copper conductor 1.5 Sq.mm single core cable as earth and connecting to earth dolly complete all as specified.

(a) One light point controlled by one, one way switch all as specified.

(b) One ceiling fan/ wall fan/ Exhaust fan point controlled by one, one way switch and regulator all as specified.

(c) One three pin 5 Amps socket outlet point controlled by one No one way switch on same board all as specified.

(d) One three pin 5 Amps socket outlet point controlled by one No one way switch on independent board all as specified.

(e) One bell point controlled by one switch all as specified.

S & F for Bell, AC, 230 volts, single pole complete all as specified.

S & F for Bell push, flush type, 5 amp complete all as specified.

All as per item No 97 here-in-before but with 2.5 Sqmm copper conductor (FRLS) cable for 15 amps socket outlet point on independent board and continuous PVC insulated copper earth wire 2.5 Sqmm in PVC casing and capping and including PVC boxes for mounting switches/sockets complete all as specified.

All as per item No 97 here-in-before but with 4.0 Sqmm copper conductor (FRLS) cable for 15 amps socket outlet point on independent board and continuous PVC insulated copper earth wire 4.0 Sqmm in PVC casing and capping and including PVC boxes for mounting switches/sockets complete all as specified.

S & F Single pole and neutral metal clad sheet enclosure with a two pin and earth plug and socket complete suitable for housing one single pole MCB all as specified.

S & F Switch piano flush type single pole one way 5 Amp all as specified.

S & F Switch piano flush type single pole one way 15 amp complete all as specified.

S & F Socket outlet 2 in 1, 3 pin, 5A complete all as specified.

S & F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type complete all as specified.

S & F for ceiling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.

S & F stepped type electronic type ceiling fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified.

S&F vertical 4 way TPN double door,recess mounted/wall mounted, MCCB as incomer and outgoing MCB SP/TP is 3 pole V-Tec of 160A rating & 16KA breaking capacity, MCCB is pre-fitted at factory & including price of MCCB MCBs, complete all as specified and as directed. ( Note : Empty space shall be covered by blanking plate and connect with lugs without any extra cost )

S&F DB TPN 4 way double door, recessed mounted/ wall mounted, complete all as specified and as directed.

S & F for MCB four pole of rated capacity 63 amps, 415 volts breaking capacity 10 KA, C-curve complete all as specified complete all as specified and as directed.

S & F for MCB DB, SPN, sheet metal enclosure, 8 way with 200 amps rated bus bar double door, fixed on wall making good to disturbed surfaces, and connecting with existing cable complete all as specified and directed.

S & F for MCB DB, SPN, sheet metal enclosure, 4 way with 200 amps rated bus bar double door, fixed on wall good to disturbed surfaces, and connecting with existing cable complete all as specified and directed.

S & F for MCB double pole of rated capacity 40 amps, 230 volts breaking capacity 10 KA, C-curve complete all as specified.

S & F for MCB double pole of rated capacity 32 amps, 230 volts breaking capacity 10 KA, C-curve complete all as specified.

S & F for MCB Single pole rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA ,C- curve complete all as specified.

M & L for Sub main wiring complete with two single core 4 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 4 sqmm in and including PVC casing caping incl accessories complete all as specified and as directed. (Note :- 3 runs of 4 Sqmm conductor and one run of PVC casing caping shall be measured as one unit length.)

M & L for Sub main wiring complete with two single core 2.5 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 2.5 sqmm in and including PVC casing caping and accessories complete all as specified and as directed. (Note :- 3 runs of 2.5 Sqmm conductor and one run of PVC casing caping shall be measured as one unit length.)

M & L for Sub main wiring complete with four single core 4 sqmm and one core of 4 sq.mm earth wire,1100volts FRLS grade, PVC insulated, stranded copper conductor cable with continuous copper earth conductor in and including PVC casing caping including accessaries complete all as specified and as directed.(Note:- 5 runs of 4 Sqmm conductor and one run of PVC casing caping shall be measured as one unit length.)

S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified and as directed.

S & F LED bulb of 12W cap 2 pin type. Make - Wipro or equivalent as per the list of make attached as Appx 'A' complete all as specified and as directed.

Supply and fix in replacement LED Tube light fittings wall mounted, 18 W LED 6500K with Opal white Poly Carbonate diffuser provided with high efficient integral constant current LED Driver 230 V etc. complete with mounting batten including all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size from ceiling rose to connector Conforming to Cat Part No. BLRB DB 118 & BLRB18 W CW LED Make :- Bajaj or equivalant as per the list of make attached as Appx 'A'

S & F in replacement of LED flood light 120 W 3rd generation LED flood light luminaire with ultra sleek, light weight and with secondary optics made of pressure die-cast housings with IP 66 rating alongwith connected accessories complete all as specified. Make :Bajaj Cat Part No : BJFL120W LED I or equivalent as per the list of make attached as Appx 'A'

S & F in replacement of LED light fittings 2'x2', 42 watts environmental friendly, new genereation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source 230 volts with all accessories internally pre wired and necessary mounting arrangements, complete all as specified. Make :- Make HAVELLS Cat part No. PLUTONEO2X2PLR42WLED840S 42 W or its equivalent as per the list of make attached as Appx 'A'.

S & F in replacement of LED light fittings 1'x1', 15watts environmental friendly, new genereation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source 230 volts with all accessories internally pre wired and necessary mounting arrangements, complete all as specified. Make :- Make HAVELLS Cat part No. PLUTO1X1PLR15WLED840S 15 W or its equivalent as per the list of make attached as Appx 'A'.

S&F LED security light in replacement of luminaries 30 watt complete with all accessories and wall mounting bracket of suitable size including clamps, nut bolts etc. prewired Conforming to Bajaj Cat Part No. BCLST 30W LED I or equivalent as per the list of make attached as Appx 'A'.

S&F in replacement of LED mirror light fitting 10 watt complete in all respect having high luminaire, integrated LED channel with white acrylic cover of 10W cap.Cat Part No BCLSB10WH of Bajaj or equivalent as per the list of make attached as Appx 'A'.

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to depth of not less than 1.5 m below ground level connected to and incl GI wire 4 mm dia and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover and MS angle iron frame, watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete all as specified and as directed. (Note:-GI earth strip and protection pipe beyond 7.5m will be measured and paid separately)

L.K.R.TIWARI CONSTRUCTION

Suma Construction

Vijay Construction and Company

Parhar Enterprise