SPECIAL REPAIR REPLACEMENT TO KITCHEN DRAIN, ROADS PATHWAY AND REPAIRREPLACEMENT OF LIGHTS, WIRING AND EM WORKS INCLUING EXTERNAL SERVICES AT MANEKSHAW CENTRE UNDER GE (SOUTH) DELHI CANTT-10

Amount

Dismantling of existing 0.8 mtr high, Stainless stell circular pipe railing with 10 mm thick glass fixed with nut & bolt complete all as specified and directed .

Refixing the 0.8 mtr high, stainless stell pipe railing with glass complete all as specified and direted . Note :- Old stainless steel pipe railing with glass as obtained from item No 1 shall be reused.

S& F in repair hermetically sealed 6-12-6 mm double glazed vision panel unit comprising an outer 6 mm toughened high performance solar control glass and inner 6 mm toughened clear glass of approved make and shade conforming to performane characteristic as specified in the technical specification , Low -E coated on surface # spacers desicants, primary and secondary seals as specified including structural silicon sealant etc . all complete fixed at all heights , levels and locations etc . complete all as specified and directed

Supplying and installing in repair 10 mm thick toughened clear glass fixed on top and bottom with Aluminum U section complete with structural sealant and other required fittings all as specified and directed by Engir- in –Charge ( All four sides of glass held by structural sealant ) ” Location – (Banquet dinning & assembly front side fixed glass)

S & F in repair 8 mm thick toughened glass in terrace railings/ staircase railings/ urinal partition incl necessery holes for fixing fixture incl SS fixture as per existing complete all as specified and directed

Dismantling stone slabs and tiles of any description or thickness in floors aprons etc , laid bedded and pointed in any mortar complete all as specified and directed

M& L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed Location – water body & entrance steps

S&F in repair 35 mm thick laminated flush door , 1.0 mm thick both side laminate with shade No D,No 10566 W V Woodlander or 10073 Wave Cango /D No 49913 seda Espana /10596 Venza Scandinavian vertical Oak / DNO 10544 Canadian walnut (new ) BWR grade ISI Mark ) complete all as specified and directed . Make : Marina or equivalent

Supplying and installing in repair, openable double swing double leaf doors in required sizes in structural glazing system using 10 mm thick toughened bent clear glass door in curved glazing system including providing & fixing necessary imported stainles steel satin finished hardware fitting patch fittings , 2 Nos 300 mm size back to back S.S handles per shutter , Heavy duty floor springs for external applications , loocking arrangements , keys etc . complete all as specified and directed Location : - Pre function area

M&L in repair, aluminium sheeting 0.50 mm thick, fixed to existing channel or RCC member with CP screws including cutting to required size etc complete all as specified and directed.

Demolition of lime concrete or cement concrete including tilling etc in ground floors and pavings not exc 15cm thick (below or above ground level) complete all as specified and directed.

M & L for 75 mm thick plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in sub base of floor / plinth proctions etc finished surface fair & even complete all as specified and directed

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade 'A' complete all as specified and directed

M&L for 16mm to 18 mm thick machine polished marble floor slab in flooring (Bottochino marble) size as existing directed, with neat cement slurry floated over bed mortar pigment to match with the shade of floor slab, joint to have hair line finish and finished with matching colour pigment and white cement, curing, rubbing, mirror polishing, washing, cleaning, making cut out for services complete all as specified and directed

M&L for 16mm to 18 mm thick machine polished marble slab in skirting (Bottochino marble) size as shown in drawings/ directed, with neat cement slurry floated over bed mortar pigment to match the shade of floor slab, joint to have hair line finish and finished with matching colour pigment and white cement, curing, rubbing, mirror polishing, washing, cleaning, making cut out for services complete all as specified and directed

M&L for 16mm to 18 mm thick machine polished marble slab in skirting (Grey william marble) size as shown in drawings, with neat cement slurry floated over bed mortar pigment to match the shade of floor slab, joint to have hair line finish and finished with matching colour pigment and white cement, curing, rubbing, mirror polishing, washing, cleaning, making cut out for services complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for double charge vitrified ceramic tiles 10 mm thick (square / rectangular ) polished area of each tiles exc. 0.42 sqm & not exc. 1.00 sqm ,in floors in floor etc set and jointed in neat cement slurry and pointed in white / coloured cement to match over and incl 15mm thick cement mortar 1:6 complete all as specified and directed Location :- Foyer , Ashoka top & RXN Area

All as per item No 18 here-in-before but as in vertical surfaces .

M& L for glazed coloured ,joint free ceramic tiles in vertical surfaces of size 450x 300 x7 mm thick ,set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

S&F in repair counter wash hand basins oval type of Size 550x450mm of Make 'Parryware catlouge No. C0418 as per 'Popular colour chart or equivalent make as approved by GE complete all as specified and directed

S&F as in repairs CP brass single hole basin mixer blush wall mounted sencer faucet with control box (battery operated ) Jaquar moddle No SNR –CHR -51443” or equivalent make as approved by GE.

S&F in repairs CP brass bottle trap 32 mm dia including jointing to waste fitting and waste pipe complete all as specified and directed

S&F as in repairs heavy duty floor door spring for glass doors of size 250x150 mm with cover plate including removal of existing floor spring and making good damaged floor to match the existing surface and fixing door complete all as specified and directed. Make -: Ozone / Kenz Location :- Floor machine of glass door

S&F as in repairs heavy duty floor door spring for glass doors of size 300x200 mm with cover plate including removal of existing floor spring and making good damaged floor to match the existing surface and fixing door complete all as specified and directed Make -: Ozone / Kenz Location :- Floor machine of glass door

S&F in repair glass door top patch with Pivet & fin ( R) and (L) complete all as specified and directed Make -: Ozone / Kenz Location :- Floor machine of glass door

S&F in repair glass door bottom patch complete all as specified and directed Make -: Ozone / Kenz Location :- Floor machine of glass door

Dismantling boarding any description fixed in any position with screws complete all as specified and directed

S&F in repair 18/19 mm thick prelaminated MDF ( medium density fibre ) board interior grade prelaminated both sides with decorative choice lamination for cup board including teak wood leeping all around fixed with screws to steel frame work complete all as specified and directed

M& L for 2nd class hard wood Plain fillets, square, rectangular or triangular in sectional area exc 13 and n. exc 25 cm , clean sawn, secured with nails or brads complete all as specified and directed

S&F in repair miled steel framed work using tubular pipe ,flat iron fillet etc including necessary cutting,drilling,welding as required complete all as specified and directed

S&F Pre-Painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws including dismantling CGI (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified & directed.

Preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

S&F in repair floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring of 140mm size with vulcanised rubber piece complete all as specified and directed

M&L ATT Post treatent for the complete building of Manekshaw centre carried out as per IS 6313 -3 complete all as specified and directed. Note :- The contractor is advised to visit the site of work before quoting the rate of this item.

S&F in repair false ceiling of 12.5 mm thick tapered edge gypsum board conforming to IS 2095 including providing and fixing frame work made out of special sections power pressed from MS Sheet and galvanised in accordance with zink coating and consisting of angle cleat of size 25 mm wide X 1.8 mm thick with flange of 22 mm and 37 mm at 1.2 mtr C/C , Angle fixed to the ceiling with dash fastener 12.5 mm dia x 40 mm long with 6 mm dia bolts to the angle hangers of 25x25x5 mm running @1.2 mtr C/C to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm , shall be fixed in a direction perpendicular to GI Channel with connecting clips made out of 2.64 mm dia x 130 mm long GI wire at every in including fixing the gypsum board with ceiling section and perimeter channel 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long the perimeter of ceiling fixed to wall / partition with the help of rawl plug at 450 mm c/c with 25 mm long screws @ 230 mm internal including jointing and fixing to a flush finish of tapered and square edge the gypsum board with filler and finish with POP as per approved colour, paper tapes including making opening for light fittings ,AC grills, diffusers cut outs made with frames of perimeter channels complete in plain horizontally / vertically location including applying coats of plastic emulsion paint over a coat of approved primer on gypsum board false ceiling horizontally / vertically as specified (at ceiling height up to 8 mtr appx) complete all as specified and directed.

Description of Work / Item(s)

Amount

Demolition of brick work built in CM incl quoins, arches, pillers etc above ground level for drains etc complete all as specified and directed

Demolition and breaking up drain pipes, 200 mm internal dia (salt glazed stoneware ,AC or reinforced concrete ) 200 mm internal dia set in cement motar including haunching and bed concrete complete all as specified and directed

M&L for cement concrete 1:3:6 type D-2 using 40 mm graded stone aggregate as in bed to drain pipes of size 200 mm bore, including packing under & haunching against the sides of pipes after they are laid and tested complete all as specified and directed

M&L for providing DWCPE(SN8) 200 (OD)/175(ID)mm diameter Pipes laid on 150 mm thick bed jointed complete with collars 175 mm dia (internal ) laid in trenches & jointed etc Length of pipe 4.5 mtr to 6 mtr complete all as specified and directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; in hard/dense soil i.e. demolition of brick work built in CM below ground level for drains etc complete all as specified and directed

All as per item no 05 above but exc 1.5 mtr and n.exc 3.00 mtr in depth complete all as specified and directed.

M&L brick work in CM (1:6) using sub class 'B' bricks, straight or curved on plan exc 6 mtr mean radius complete all as specified and directed

Demolition of cement concrete/ bituminous road in ground floors and pavings n'exc 15 cm thick below or above ground level (unreinforced) complete all as specified and directed

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed

Extra for forming fair finished drain or channel n.exc 75 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc complete all as specified and directed

M&L for cement concrete type B-0, 1:2:4 using 12.50mm graded stone aggregate as in copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed

M&L for 15 mm thick cement mortar plaster on brick or concrete surfaces in CM 1:4 finished even and smooth surface with using extra cement on wall of open drains in foul conditions complete all as specified and directed

S&F of precast RCC polymer concrete, M-30 grade of concrete by using nylon fibers,with 10 nos of round hole on each drain cover, of size 1000mm x 700mm & 70mm thick,manufactured by using jointless FRP moulds and casted by vibro compaction process, drain cover reinforced with 8mm dia tor mild steel bars @100mm c/c both bays, set on drain as cover slab complete all as specified and directed. Notes: - (i) Make of SFRC Manhole/drain cover and frame :(a) M/sKreative Concrete Compant, Plot No-61/50, Palli Industrial Area, Faridabad,Mob-999981563, 9811437574. (b) M/s KK Manholes & Grating Co. Pvt. Ltd, 12/16, Sarvapriya Vihar, New Delhi, Mob-9910012478, 011-26864895.(c) Or equivalent as approved by GE” (ii) Contractor will provide manufactuerer test certificate of Drain Cover.

Cutting into existing manholes for connecting new drains, making good to pipes and rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required, Internal dia of pipe 150mm complete all as specified and directed

Returning filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and directed

Removing excavated materials to a distance exc 1.50Km but n.exc 5 Km and depositing where directed at a level n.exc 1.50m above the starting point in soft/loose soil complete all as specified and directed

S&F cast iron sand soil waste or vent pipes (ISI Marked), in any length with or without ears with joints in CM (1:3), laid in trenches, floors or fixed to walls all as directed including making good to match with existing surfaces complete all as specified and directed for the following sizes of pipes:- a) 100 mm bore of pipe.

S&F grease oil grease trap, of size 1.5 mtr x .5 mtr x1.00 mtr of 2 mm thick stain less steel of 2 mm thick having 100 mm dia inlet and 100 mm dia outlet pipe , stainless stell bucket of 15 ltr capacity , o1 nos ball valve for releasing oil with provision of transparent pipe for seeing oil level , hopper type design ( two box partition) for better sludge removing including connecting the existing CI pipes with the grease trap complete all as specified and directed by Engr-in- Charge

Description of Work / Item(s)

Amount

M&L for treatment of soil under existing floors or voides in masonery walls using imidacloprid emulsion as per IS 6313-3 , 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors/walls complete all as specified and directed.

Providing and fixing of 18mm thick, 125mm wide, random length : 300-1200/1500mm Solid Antique European white Oak flooring – Lamett collection, PEFC certified, having brushed, AD 48 PU Coated surface, round bevel for better edge protection, moisture content between 7-11% as measured by a wood moisture meter with manufacture’s original warranty (on surface finish and milling). Installation to be done on top of Foam & Polythene over a flat dry ply base (moisture content not exceeding 3.9% as measured by a concrete moisture meter) concrete subfloor. Installed floor to be finished with genuine oak skirting and edge profiles of matching decors.Aluminum framework, Size use on top of subfloor, 50x25 mm (14 gauge) @450mmx450mm distance center to center,19mm double ply on top, water resistant/water proof, Greenlam or equivalent, A layer of Plythene 0.5mm, & Polyurethane foam 2.5mm complete all as specified and directed .Make : EURO Flooring Pvt Ltd / Span Flooring

Providing and fixing of 18mm thick, 125mm wide, random length : 300-1200/1500mm Solid Antique European white Oak flooring of Span Floors – Lamett collection, PEFC certified, having brushed, AD 48 PU Coated surface, round bevel for better edge protection, moisture content between 7-11% as measured by a wood moisture meter with manufacture’s original warranty (on surface finish and milling). Installation to be done on top of a flat dry ply base (moisture content not exceeding 3.9% as measured by a concrete moisture meter) subfloor. Installed Wall Paneling to be finished with genuine oak edge profiles of matching décors. Aluminum framework, Size use on top of wall, 25x25 mm (14 gauge) @450mmx450mm distance center to center, 19mm single ply on top, water resistant/water proof, Greenlam or equivalent. Make : EURO Flooring Pvt Ltd / Span Flooring

Supply & Fixing of beading 21mmx21mm (available in maranti wood only) 1Length (2100mm) suitable for wooden flooring to match solidwood decors as required to fix as per manufacturer instruction and as directed including taking down wooden skentling complete all as specified and directed. Make :- EURO FLOORING PVT LTD/SPAN FLOOR

Description of Work / Item(s)

Amount

Taking down carefully old unservicable copper point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, bell push etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete all as specified and directed.

M&L light/fan/bell point controlled by one modular switch with PVC insulated, unsheathed, multi stranded, single core copper conductor cable 2.5 Sqmm suitable for fixing in existing concealed conduit with modular sunken pressed steel terminal boxes 2 mm thick of required size and modular white cover plate and frame in different module housing for fixing modular switches/modular socket and modular fan regulator etc. PVC insulated, unsheathed, multi stranded, single core copper conductor cable 2.5 Sqmm used as earth wire to commen earth and connected to common dolly drawn in same conduit complete all as specified and directed. Note : 1. The rates are inclusive of passing all the light circuits inside the false ceiling through heavy duty flexible PVC conduit and providing connectors for connection to light fittings. 2. The rates are inclusive of Cutting / Chassis and making good to the disturbed surfaces with necessary PCC Works and providing / laying of New PVC Conduit if there is a damage/ blockage to the existing PVC Conduit in concealed wall. 3. The Rates are inclusive of Scaffolding along with proper safety , precautionary items like 25 mm HDPE sheet , 6 mm ply , safety nets to work at heights.

(a) One light / fan / bell point controlled by one No one way modular switch

(b) One 3 pin 5 Amps socket outlet point controlled by one No one way modular switch and modular socket on independent board.

(c) All as per item No 2 but point wiring for 16 Amps for modular socket point with 2.5 Sqmm single core copper cable and earth continuity wire with 2.5 Sqmm single core cable for one three pin 15 Amps modular switch / socket outlet point on independent board.

S&F switch modular single pole, one way 6 Amp, 01 module complete all as specified and directed Make : Model Crabtree of Havells / Model – Unica of Schneider / Model – Marius of Legrand

S&F switch modular single pole, one way 16 Amp, 01 module complete all as specified and directed Make : Model Crabtree of Havells / Model – Unica of Schneider / Model – Marius of Legrand

S&F modular socket 6 Amp-2/3 pin combined, 2 module complete all as specified and directed Make : Model Crabtree of Havells / Model – Unica of Schneider / Model – Marius of Legrand

S&F modular socket 6/16 Amp-2/3 pin combined, 2 module complete all as specified and directed Make : Model Crabtree of Havells / Model – Unica of Schneider / Model – Marius of Legrand

S&F bell push, flush type 6 Amps complete all as specified and directed Make : Model Crabtree of Havells / Model – Unica of Schneider / Model – Marius of Legrand

S&F in replacement of electric bell (Dingdong) AC, 230 volts single phase complete all as specified and directed

S & F Surface mounting LED Integrated Aluminium Batten luminaire Polycarbonate co-extrusion tube for 20W LED light housing with engg-plastic end caps.Co-extrusion tube top part is made of polycarbonate material, and the diffuser is made of opal polycarbonate material with groove inside for PCB.LED populated on PCB comprising of LED’s connected in series parallel. Driver: Constant current LED driver. Fixture should have minimum system lumen of 2000lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 25K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >80,PF – 0.95 , THD <20%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 3kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer complete with including flexible wire complete all as specified and directed . Make - Bajaj Cat Part No - BCLAB 20W WH LED P / Crompton Cat Part No- LDL-20-CDL / Make - Wipro Cat Part no:LL20-281-XXX-65AL1

S&F Recess Mounting LED Circular COB made up of die‐cast aluminium recess mounted housing (dimming control) of 40/41 Watt comprising of LED’s suitable for working on DALI System with suitable Dali Driver,Aluminium reflector fixed in die‐cast aluminium housing suitable for recess mounting in POP or any type of false ceiling supplied with wedge bracket to fix in New POP or any type of false ceiling including cutting / grouting of any type of false ceiling and POP ceiling to match with POP through three nos. spring loaded latches .Finish: White powder coated . Driver: Constant current LED driver. Fixture should have minimum system lumen of 4000lm & minimum efficacy at System level >=100 lumens/ watt, Life of fixture : 25K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >80, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 2kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer. and getting electrically connected the fitting with switch board for suitable size of PVC copper wire complete all as specified and directed. Make - Bajaj Cat Part No - BRDCSL 40W / Crompton Cat Part No- CDR-215-40-40-SL-NWH / Wipro Cat Part no:LD56-501-060-40-XX

S&F LED Circular Recess mounting LED Downlighter of 32 Watt with Powder coated spun aluminium ring. LEDs module is mounted on extruded aluminum heat sink for better thermal management. LEDs incorporated in Aluminium anodised sheet for minimizing glare. Aluminium reflector is fixed with heat sink by SS clips.. Driver: Constant current LED driver. Fixture should have minimum system lumen of 3200lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700K with same lumens/w. CRI >70, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 2kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer suitable for POP or any type of false ceiling supplied with wedge bracket to fix in New POP or any type of false ceiling including cutting / grouting of any type of false ceiling to match with fitting and providing connections to the fitting complete all as specified and directed. Make - Bajaj Cat Part No - BCDLR 32W / Philips Cat Part No- RS378Z M102 D150 R-R AJU / Wipro Cat Part no-LD56-381-060-40-XX

S&F Circular Recess mounting 20W LED Downlighter. Powder coated spun aluminium ring. LEDs module is mounted on extruded aluminum heat sink for better thermal management. LEDs incorporated in Aluminium anodised sheet for minimizing glare. Aluminium reflector is fixed with heat sink by SS clips.. Driver: Constant current LED driver. Fixture should have minimum system lumen of 2000lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700K with same lumens/w. CRI >70, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 2kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer suitable for POP or any type of false ceiling supplied with wedge bracket to fix in New POP or any type of false ceiling including cutting / grouting of any type of false ceiling to match with fitting and providing connections to the fitting complete all as specified and directed. Make - Bajaj Cat Part No - BCDLR 20W / Philips Cat Part No- DN590B M LED20S-6500 PSU WH WB / Wipro Cat Part no- LD56-251-060-40-XX*

S&F in replacement LED garden light (Bollard) light fitting luminaries of 8/9 Watt in Round Shape with 1 mtr height of 3000K with IP 65 , 70 Lm/Watt, PF>0.90 complete with all accessories including necessary connections with suitable of copper cable connections complete all as specified and directed. Make - Bajaj Cat Part No - BGBOL 605 09W LED WW , Make Philips Cat Part No- YOLO PEDESTAL 58169 , Make - Havell's Cat Part no:BAMBOOBLS8WLED830PSYMTOPC

S&F 120W LED Flood light Luminaire having Pressure die-cast aluminium LED housing designed to act as heat sink for efficient dissipation of heat. Electrochemically brightened and Heat resistant toughened glass provided with gasket and SS clips. Luminaire is provided with a MS mounting bracket fixed on pressure die-cast aluminium housing for aiming adjustment. Driver provided with built-in input voltage surge, open and short circuit protection. Finish: Powder coated. Fixture should have minimum system lumen of 9600lm & minimum efficacy at System level >=120 lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >70, THD <10%@ 240v ac, P.F - 0.95 , An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 4kv, External Surge 10kv, IP 66, IK07. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer complete all accessories including necessary connection of suitable size wire complete all as specified and directed.Make - Bajaj Cat Part No - BJFL 120W LEDI , Make Crompton Cat Part No-LFLN-120-CDL/60-M , Make - Havells Cat Part no- JETAIRISFLS120WLED757APWBLTG

S&F 120W LED Highbay having Pressure die-cast aluminum housing and LED driver compartment. Eye-bolt provided for suspension mounting. LED fixed on die-cast aluminum heat sink for proper thermal management. Optics: Secondary lens optics provided.Constant current driver to have built-in surge, open & short circuit protection.Completely prewired with accessories up to terminal block. Fixture should have minimum system lumen of 13200lm & minimum efficacy at System level >=110 lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >70, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 4kv, IP 65, IK06. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer complete all accessories including hanging of Highbay light fitting with decorative suspension system complete all as specified and directed. Make - Bajaj Cat Part No - BGHBM nxt B156LWHNBSD , Crompton Cat Part No-CIP-320-120-57-90D-HL4-GL-NSR , Wipro Cat Part no-LH17-192-060-50-XX

S & F in replacement of LED based mirror light fitting 22 Watt Ip 20 6500k 2000Lm 25000 Hr. verticle type and necessary connection of suitable size wire and fixing adjacent to the mirror in washroom including grouting in wall/surface and using necessary nut, bolts and washers etc complete all as specified and directed. Make - Philips Model- Wall SCONE light or equivalent

Supply & Fixing in replacement 8/9 W LED Bush/Spike Luminaire having Graphite grey powder coated integral aluminium housing. Die-cast aluminium housing comprises Warm White (WW) COB LED and reflector.COB LED housing covered with die-cast aluminium ring with weatherproof gasket and toughened glass. Adjustable mounting bracket with spike is provided for easy to focus the object. 2 nos., Ø8mm holes also provided on adjustable mounting bracket for surface mounting. Constant current LED driver.Fixture should have minimum CCT 3000K. An operating Voltage Range of 140 - 270 V. Minimum Degree of protection : IP65. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer suitable for fixing around the wall of building complete with all accessories including necessary connection of suitable size wire and fixing adjacent to the outer wall of Manekshaw Bldg including grouting in wall/surface/masonary block and using necessary nut, bolts and washers etc complete all as specified and directed . Make- BAJAJ , Cat Part No- . BGSBL9WLEDWW, Make - Havells Cat no - LYCUSSPS9WLED730PSYMBOTG, Make -Wipro Cat No-.LF05-600-036-27-XX

Supply and fixing in replacement 36/40 W LED Recess mounting 4’x 1’ LED Luminaire having CRCA steel sheet housing comprising of LED’s connected in series parallel. Opal diffuser fixed in separate CRCA sheet steel frame.Opal diffuser frame is held in with screws and SS strings and it can be suspended for easy maintenance. Driver: Constant current output driver. Finish: Housing white powder coated. (RAL9016). Fixture should have minimum system lumen of 3600-4000lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >80, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 3kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer complete all accessories including necessary connection of suitable size wire complete all as specified and directed. Make - Bajaj Cat Part No - BZRSLL 36W WH LED i / Crompton Cat Part No- LCTLRNE-40-CDL(1X4) / Wipro Cat Part no:CRCO13R036HP57G2

S&F 36W LED Recess mounting 2’x 2’ LED Luminaire having CRCA housing comprising of LED’s connected in series parallel. Opal diffuser fixed in separate white powder coated sheet steel frame. Opal diffuser frame is held in with housing by screws and SS Strings for easy maintenance. Driver: Constant current LED driver. Finish: White powder coated. Fixture should have minimum system lumen of 3600lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >80, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 2.5kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer complete all accessories including necessary connection of suitable size wire complete all as specified and directed. Make - Bajaj Cat Part No - BZRSQL36W GZi WH / Crompton Cat Part No- LCTLRNE-36-FO-CDL / Make - Philips Cat Part no: RC380BLED36S-6500 G5 L60W60 PSU OD SG

S&F 16/18W LED Surface mounting 1’x 1’ LED Luminaire having CRCA sheet housing comprising of LED’s connected in series parallel. Opal diffuser fixed in separate CRCA sheet frame.Opal diffuser frame is held in with housing for easy maintenance. Driver: Constant current LED driver.Finish: Housing white powder coated. Fixture should have minimum system lumen of 1800lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >80, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 3kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer complete all accessories including necessary connection of suitable size wire complete all as specified and directed. Bajaj Cat Part No - BZSSQL 18W LED WHi ,Make Crompton Cat Part No-LCTLSNE-18-FO-CDL , Make - Philips Cat Part no- SM200C LED16S 6500 PSU OD WH

Taking Down Existing LED Spot light fitting along with Track Mounting Luminaire & connected accessories , Keeping in safe custody and refixing in its orginal position with suitable size of nuts , bolts , screws and washers after completion of wiring and testing on completion of work. Note : The contractor shall be responsible for any damage to light fitting / track mounted structure during taking down and refixing.Cost of fixing New Nuts,Bolts & Screws deemed to be included in item rates.

S & F in replacement water tight fitting (Water Proof ) Static White Ground Burried Narrow/ Medium/ Wide/ Asymmetric beam Cylindircal Walkover luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 2.5W to 15W at steady state full intensity. Luminaire should be able to run on AC/DC Voltage. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP 67 or higher. Housing should be made of Die cast aluminium housing with 3-4mm thick safety glass. Impact resistance level should be suitable to site condition. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -30°C to +50°C, Operating Humidity : 10% - 90% complete all accessories including necessary connection of suitable size wire from MCB DB / Switch Board to water tank where the LED water tight fitting to be fixed complete all as specified and directed. Make Ligman – Model - Funel 8 w / Havells Model - marinashine mini 8w / Reiz – Model -volcano 8w

Supply, installing, commissionig and testing twin universe DALI Router with Ethernet connection as a network backbone. Programmable through software, the router supports 128 devices with 250mA power supply on each subnet. Upto 100 such Router can be networked together and upto 12800 DALI devices can be networked together on a Route system. With in built Real time Clock, the product conforms to DALI standard IEC60950 and further EMC conformance to EN55015 and EN61547 and Safety confarmance to EN60950. Make - Helvar 910 or equivalent in Lutron / Crestron including complete necessary eletrical connection with dimmable light fittings to DALI system for the controlling of whole lights in grouping or individually complete all as specified and directed. (Note : This system to be fixed in the existing wooden/steel wall mounted panel box)

Supply, installing, commissionig and testing custamisable wall mounted DALI compatible user interfaces allowing control of dimmable lighting system. Each interface will have tactile buttons with Indicators LEDs and with IR receiver giving optioin of remote operation using hand held remote controls. Progammable using software and designed to fit standard 3"x3" wall boxes with choice of Black & White finishes and multiple choices in outer plates. Typically choice of 2 to 8 buttons available of the Make : Helvar or equivalent in Lutron / Crestron including complete necessary eletrical connection with dimmable light fittings to DALI system for the controlling of whole lights in grouping or individually complete all as specified and directed. (Note : This system to be fixed in the existing wooden/steel wall mounted panel box)

S&F LED Briteq - Belgium, BT -Theatre 100 EC MK2 of 100 Watt warm white Cob LED light fitting with Barndoors - 3200K - DMX - Neutrick powercon connectors - 10-50 Deg manual zoom with 125 power consumption suitable for stage light of Zorawar & Ashoka Auditorium including including necessary electric connections by approriate size of PVC copper wire with incoming submain and adoptor complete all as specified and directed. Make : Briteq-Belgium or equivalent in Elation / USA ETC .

S&F LED Briteq - Belgium, BT -Theatre 60 FC of 60 Watt full colour RGBW theatre LED spot light fitting with manual zoom 10-50 Degree with Barndoor - DMX and RDM compatible of 62 Watt power consumption suitable for stage light of Zorawar & Ashoka Auditorium including including necessary electric connections by approriate size of PVC copper wire with incoming submain and adoptor complete all as specified and directed. Make : Briteq-Belgium or equivalent in Elation / USA ETC

S&F LED Briteq - Belgium, LDP Cobwash 50 WW of of 50 Watt warm white Cob LED light fitting with Barndoors - 3200K - DMX of 66 Watt power consumption suitable for stage light of Zorawar & Ashoka Auditorium including including necessary electric connections by approriate size of PVC copper wire with incoming submain and adoptor complete all as specified and directed. Make : Briteq-Belgium or equivalent in Elation / USA ETC .

S&F LED Nicolaudie - France - Stick DE3 - DMX controller of 1024 DMX channel with 500 scenes, 10 Zones - RS232, ports, infra red, clock and calendar and touch sensitive buttons with Windows/Mac software - iPhone/iPad/Android compatible complete suitable for stage light of Zorawar & Ashoka Auditorium including including necessary electric connections by approriate size of PVC copper wire with incoming submain and adoptor complete all as specified and directed. Make : Nicolaudie-France-Stick DE3-DMX or equivalent in Elation / USA ETC

S&F LED Contest - France - Pilot192Pro of 192 channel DMX console, 30X8 program banks with 12 chasers complete suitable for stage light of Zorawar & Ashoka Auditorium including including necessary electric connections by approriate size of PVC copper wire with incoming submain and adoptor complete all as specified and directed. Make : Contest-France-Pilot of 1992 or equivalent in Elation / USA ETC

S&F LED Briteq - Belgium, DMS26 with 6 output DMX splitter/booster/merger of 2 DMX with input + 6 DMX - outputs and each equipped with 3 pin and 5 pin XLR connectors of 100% electrical isolation between all in/output complete suitable for stage light of Zorawar & Ashoka Auditorium including including necessary electric connections by approriate size of PVC copper wire with incoming submain and adoptor complete all as specified and directed. Make : Briteq-Belgium or equivalent in Elation / USA ETC

S&F in replacement of Adoptor of 24 Volts for AC to DC supply suitable for 6 to 12 outgoing port to connections of step lights circuit upto 20 Amps capacity complete all as specified and directed

Taking down of old unserviceable ceiling fan/exhaust fan and dismantling of blades and cleaning or dusting the blades and bearing assembly properly and deposit to MES yard/store complete all as specified and directed

Supply and fix in replacement of BLDC (Bruishless Direct Current) ceiling fan of 1200mm sweep, not less than 350 RPM, not less than Air Delivery 215 cfm, Voltage 220V, high air follow with with silence operation, having full copper motor & ribbed 3 Nos A/M blades suitable for working on fan regulator. The BLDC motor fan shall have 100% rust-free blade. the fan shall have BEE 5 star rating and compliant with IS-374 and making ncessary electric connection of suitable PVC copper wire from ceiling rose to ceiling fan complete all as specified & directed. (Note : Existing fan to be deposited in MES yard)

S & F in replacement of modular fan step regulator, 120 W-2 module complete all as specified and directed

S&F in replacement of metal body exhaust fan 450 mm sweep, 230 Volts with louver and copper wound including necessary electric connection with appropriate size of PVC copper wire from ceiling rose/switch board to exhaust fan including fixing of nut-bolts of suitable size and making good the disturbed surface of wall with OBD/White wash to match with existing complete all as specified and directed of Make : Halonix Cat Pt No - Krypton (HDEF) or equivalent to Havells/Bajaj/CG. (Note :- Existing unserviceable exhaust fans to be deposited in MES store)

M&L sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 1.5 Sqmm, 1100 Volts grade on & including existing PVC Conduit 25mm medium grade complete with conduit accessories and copper cable 1.5 sqmm continuous earth wire complete all as specified and directed (Note :- (a) Two runs of cable with 01 earth wire shall be measured as one length) (b) The rate is inclusive of taking down old submain wiring, making good the disturbed surface and same surface finishes with the adjoining surface of disturbed area ie with OBD/colour wash/white wash and wall putty where ever required. (c) The rate are inclusive of passing all the submain wiring circuit inside the false ceiling through suitable size of PVC conduit and providing new PVC conduit on found of any blockage or damage of existing conduit. Note (d) : Sub main wiring to be laid under false ceiling in heavy duty flexible conduit from ceiling rose or junction box to Light Fitting and providing connectors for connection to light fittings. (e) The Rates are inclusive of Scaffolding along with proper safety , precautionary items like 25 mm HDPE sheet , 6 mm ply , safety nets to work at heights .

M&L sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 2.5 Sqmm, 1100 Volts grade on & including existing PVC Conduit 25mm medium grade complete with conduit accessories and copper cable 2.5 sqmm continuous earth wire complete all as specified and directed (Note (a)Two runs of cable with 01 earth wire shall be measured as one length) (b) The rate is inclusive of taking down old submain wiring, making good the disturbed surface and same surface finishes with the adjoining surface of disturbed area ie with OBD/colour wash/white wash and wall putty where ever required. (c) The rate are inclusive of passing all the submain wiring circuit inside the false ceiling through suitable size of PVC conduit and providing new PVC conduit on found of any blockage or damage of existing conduit. Note (d) : Sub main wiring to be laid under false ceiling in heavy duty flexible conduit from ceiling rose or junction box to Light Fitting and providing connectors for connection to light fittings. (e) The Rates are inclusive of Scaffolding along with proper safety , precautionary items like 25 mm HDPE sheet , 6 mm ply , safety nets to work at heights.

M&L sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 4 Sqmm, 1100 Volts grade on & including existing PVC Conduit 25mm medium grade complete with conduit accessories and copper cable 4 sqmm continuous earth wire complete all as specified and directed Note :- (a) Two runs of cable with 01 earth wire shall be measured as one length) (b) The rate is inclusive of taking down old submain wiring, making good the disturbed surface and same surface finishes with the adjoining surface of disturbed area ie with OBD/colour wash/white wash and wall putty where ever required. (c) The rate are inclusive of passing all the submain wiring circuit inside the false ceiling through suitable size of PVC conduit and providing new PVC conduit on found of any blockage or damage of existing conduit. Note (d) : Sub main wiring to be laid under false ceiling in heavy duty flexible conduit from ceiling rose or junction box to Light Fitting and providing connectors for connection to light fittings. (e) The Rates are inclusive of Scaffolding along with proper safety , precautionary items like 25 mm HDPE sheet , 6 mm ply , safety nets to work at heights.

M&L sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 6 Sqmm, 1100 Volts grade on & including existing PVC Conduit 25mm medium grade complete with conduit accessories and copper cable 6 sqmm continuous earth wire complete all as specified and directed Note :- (a) Two runs of cable with 01 earth wire shall be measured as one length) (b) The rate is inclusive of taking down old submain wiring, making good the disturbed surface and same surface finishes with the adjoining surface of disturbed area ie with OBD/colour wash/white wash and wall putty where ever required. (c) The rate are inclusive of passing all the submain wiring circuit inside the false ceiling through suitable size of PVC conduit and providing new PVC conduit on found of any blockage or damage of existing conduit. Note (d) : Sub main wiring to be laid under false ceiling in heavy duty flexible conduit from ceiling rose or junction box to Light Fitting and providing connectors for connection to light fittings. (e) The Rates are inclusive of Scaffolding along with proper safety , precautionary items like 25 mm HDPE sheet , 6 mm ply , safety nets to work at heights.

M&L sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 10 Sqmm, 1100 Volts grade on & including existing PVC Conduit 25mm medium grade complete with conduit accessories and copper cable 6 sqmm continuous earth wire complete all as specified and directed Note :- (a) Two runs of cable with 01 earth wire shall be measured as one length) (b) The rate is inclusive of taking down old submain wiring, making good the disturbed surface and same surface finishes with the adjoining surface of disturbed area ie with OBD/colour wash/white wash and wall putty where ever required. (c). The rate are inclusive of passing all the submain wiring circuit inside the false ceiling through suitable size of PVC conduit and providing new PVC conduit on found of any blockage or damage of existing conduit. Note (d) : Sub main wiring to be laid under false ceiling in heavy duty flexible conduit from ceiling rose or junction box to Light Fitting and providing connectors for connection to light fittings. (e) The Rates are inclusive of Scaffolding along with proper safety , precautionary items like 25 mm HDPE sheet , 6 mm ply , safety nets to work at heights.

M&L earthing with GI earth plate electrode 600 x 600 x 6mm thick burried directly in ground in ground (earth pit plate less than 2.5 mtrs below ground level) with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised iron strip as earth lead of 25x4mm by means of bolts, nuts check nuts to earth test point including necessary PCC 1:2:4 type B-1 pit, cover frame, GI pipe 15mm dia light grade with funnel and locking arrangement complete all as specified and directed

M&L earthing with GI earth plate electrode 600 x 600 x 6mm thick burried directly in ground in ground (earth pit plate less than 2.5 mtrs below ground level) with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised iron wire of 4 Sqmm dia as earth lead by means of bolts, nuts check nuts to earth test point including necessary PCC 1:2:4 type B-1 pit, cover frame, GI pipe 15mm dia light grade with funnel and locking arrangement complete all as specified and directed

M & L Earth continuity conductor or main earthing lead fixed on wall/ceiling in batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed on poles or any other indicated situation for loop earthing etc as required 25x4mm dia galvanised iron strip complete all as specified and directed

M & L Earth continuity conductor or main earthing lead fixed on wall/ceiling in batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed on poles or any other indicated situation for loop earthing etc as required 4mm dia galvanised iron or steel wire complete all as specified and directed

S&F MCB DB SPN 8 Way with metal double door, (IP-43 Protection) flush mounting epoxy powder control having 200 Amps rated bus bar complete all as specified and directed

M&L in replacement MCB SPN 'C' curve 40 Amps 240 Volts, 10 KA complete all as specified and directed

M&L in replacement MCB SPN 'B' curve 40 Amps 240 Volts, 10 KA complete all as specified and directed

M&L in replacement MCB SP 'C' curve 10 to 40 Amps 240 Volts complete all as specified and directed

S&F in replacement of sheet metal enclouser MCB DB IP-43 (IK-09) double door bus bar neutral link earth bar and din rail VTPN into rows of 8+48 (16 Way) complete all as specified and directed Make : Legrand Cat Pt No : 507707 or equivalent . (Note : The VTPN to be fixed as per sample as fixed existing)

S&F in replacement MCCB TP 63 Amps, 415V, with 16kA complete all as specified and directed

S&F in replacement of fire retaindant electric insulation synethic mat INSULATICA 2000 for 11 KV 3.0 mm thick + 10 % confirming to BIS DOC No ETD-02 (5231) P dt 2003 meeting requirement of IS-3043, IS :8437 and IEC 479 pub 11EC 111 & 1112 tested for breakdown strength tensile/elongation agening properties. Insulation resistance, affects of acid, alkeline, Diesel & transformer oil, leakage cumertest fire test etc having min width of 1000 mm+20 mm complete as required suitable and having adhesive and alled chemical and scaling of all joints and border ends and fixing decorative taps the installed sheet complete all as specified and directed. Note:- The contractor have to submit guarantee certificate.

S&F in replacement MCCB FP, 415 Volts, 50 Hz of 630Amps with braking capacity 50 kA complete all as specified and directed

S&F in replacement MCCB FP, 415 Volts, 50 Hz of 400Amps with braking capacity 50 kA complete all as specified and directed

S&F in replacement MCCB FP, 415 Volts, 50 Hz of 250Amps with braking capacity 36 kA complete all as specified and directed

S&F in replacement MCCB FP, 415 Volts, 50 Hz of 160Amps with braking capacity 36 kA complete all as specified and directed

S&F in replacement MCCB FP, 415 Volts, 50 Hz of 100/125Amps with braking capacity 25 kA complete all as specified and directed

S&F in replacement MCCB FP, 415 Volts, 50 Hz of 63Amps with braking capacity 16 kA complete all as specified and directed

S&F in replacement Indicator lamp LED type for 3 Phase as R.Y.B - 3 Nos (1 Set) complete all as specified and directed

Supply, installation, testing and commissioning of LT Panel Board as "Main Panel" (KIOSK) type totally enclosed made of MS sheet 3.15 mm thick outdoor type weather proof having sloping canopy with both side openable,locking arrangement and painting etc (factory made) comprising the following complete all as specified and directed :- (at Exhibition lower)

INCOMING :-

(i) Incoming MCCB 400 Amps ,FP, 415 Volt, 50 Hz with braking capacity 36 KA - 1 No.

OUTGOING :-

(i) Outgoing MCCB 63 Amps, FP, 415 Volt with braking capacity 16 KA - 7 Nos.

(ii) Copper busbar of 1000 Amps rating with air insulated, TPN mounted on porcelain insulators with epoxy based colour coding - One set. (as R.Y.B. & N)

(iii) Digital Multifunctional panel mounted meter with CT's - 800/5A in accuracy class 1.0, CT primary programmable upto 6000A measures and display phase to phase voltage, phase to neutral, instatanious average, maximum and total load current, Active power KW, Reactive power KVAR and apparent power KVA, instantanious and total power factor, frequency RS 485 communication (optional)

(vi) Panel wiring with 2.5 sqmm copper cable PVC single core - 1 Job

(vii) Indicator lamp LED type for 3 Phase as R.Y.B - 3 Nos - 01 set

(viii) Civil work for erection of panel.

(ix) All accessories will be prewired with suitable size of copper thimble, copper conductor cable or strip as required. The cable shall be used for all outgoing ways as an insulated with fibre glass insulation to with-stand high temperature and the panel shall be completed with foundation as required on recommended by manufacturer.

Supply, installation, testing and commissioning of LT Panel Board as "Main Panel" (KIOSK) type totally enclosed made of MS sheet 3.15 mm thick outdoor type weather proof having sloping canopy with both side openable,locking arrangement and painting etc (factory made) comprising the following complete all as specified and directed :- (at Cafeteria area, Exhibition Pkg area, Band stand lighting area & VIP garden)

INCOMING :-

(i) Incoming MCCB of 315 Amps , FP , 415 Volt, 50 Hz with braking capacity 36 KA - 1 No.

OUTGOING :-

(i) Outgoing MCCB 63 Amps, FP, 415 Volt with braking capacity 16 KA - 5 Nos.

(ii) Copper busbar of 1000 Amps rating with air insulated, TPN mounted on porcelain insulators with epoxy based colour coding - One set. (as R.Y.B. & N)

(iii) Digital Multifunctional panel mounted meter with CT's - 800/5A in accuracy class 1.0, CT primary programmable upto 6000A measures and display phase to phase voltage, phase to neutral, instatanious average, maximum and total load current, Active power KW, Reactive power KVAR and apparent power KVA, instantanious and total power factor, frequency RS 485 communication (optional)

(vi) Panel wiring with 2.5 sqmm copper cable PVC single core - 1 Job

(vii) Indicator lamp LED type for 3 Phase as R.Y.B - 3 Nos - 01 set

(viii) Civil work for erection of panel.

(ix) All accessories will be prewired with suitable size of copper thimble, copper conductor cable or strip as required. The cable shall be used for all outgoing ways as an insulated with fibre glass insulation to with-stand high temperature and the panel shall be completed with foundation as required on recommended by manufacturer.

Dismantling and taking out unserviceable / defective of LT Panel board feeding to essential area by disconnecting all electrical connections, nut & bolts complete all as specified and directed

S&F in replacement of online UPS of 5 KVA capacity for un-interrupted power supply single phase, 230 Volts, AC, 50 Hz with Innput Power : Single Phase 160V to 260V sinewave input and Output Power : Single Phase, 230V +/-1% sinewave with minimum 30 minutes backup, SMF Battery Bank(min 3500VAH), in built galvanic isolation transfomer, IGBT Based Double conversion PWM, Harmonic distortion,5% including cabling 5 meters for input and output, overall efficieny >/=90% complete all as specified and directed. (Note : To be installed at Conference Room and the existing u/s UPS to be deposited after taking out in MES yard)

S&F in replacement of online UPS of 2 KVA capacity for un-interrupted power supply single phase, 230 Volts, AC, 50 Hz with Innput Power : Single Phase 160V to 260V sinewave input and Output Power : Single Phase, 230V +/-1% sinewave with minimum 30 minutes backup, SMF Battery Bank(min 1500VAH), in built galvanic isolation transfomer, MOSFET Based Double conversion PWM, Harmonic distortion,5% including cabling 5 meters for input and output, overall efficieny >/=90% complete all as specified and directed. (Note : To be installed in FDB rooms and the existing u/s UPS to be deposited after taking out in MES yard)

S&F of online UPS of 1 KVA capacity for un-interrupted power supply single phase, 230 Volts, AC, 50 Hz with Innput Power : Single Phase 160V to 260V sinewave input and Output Power : Single Phase, 230V +/-1% sinewave with minimum 30 minutes backup, SMF Battery Bank(min 700VAH), in built galvanic isolation transfomer, MOSFET Based Double conversion PWM, Harmonic distortion,5% including cabling 5 meters for input and output, overall efficieny >/=90% complete all as specified and directed

S&F online UPS of 7.5 KVA capacity for un-interrupted power supply single phase, 230 Volts, AC, 50 Hz with Innput Power : Single Phase 160V to 260V sinewave input and Output Power : Single Phase, 230V +/-1% sinewave with minimum 60 minutes backup, SMF Battery Bank(min 11000VAH), in built galvanic isolation transfomer, IGBT Based Double conversion PWM, Harmonic distortion,5% including cabling 5 meters for input and output, overall efficieny >/=90% complete all as specified and directed

S&F in replacement ceiling rose surface Bakelite 60x 25 mm two to three terminals, ISI marked complete all as specified and directed

Design, Supply , Installation , testing and commissioning in replacement of LED fibre Optic Step light 5 watt for step nosing having aluminium extrusion, antislip profile with blue LED on either one or both ends and other accessories such as control transformer , properly mounting and covering control transformer .This item shall be complete in all respects with LED light , Control transform,ers , clamps , all necessary hardwares , control transformer cover etc comprising of following (Make – Fibre Optic or equivalent in Pranat , Philips ): (i) Aluminium Extrusion (ii) Anti Slip Profile (iii) Combination of LED and 5 mm fibre optic. (iv) Row numbering on one side / both side with blue LED duly installed with 1.0 metre ( end to end ) with seat and row number on both side.

M&L in replacement of pressed FRP box of 15x20x10 cm size fixed to pole/pipe incl 2 Nos aluminium bus bar 6/10 Amps fixed on insulator and one number of MCB 10 amps including taking down old one complete all as specified and directed.

S&F in replacement, PVC FRLS unsheathed multi stranded copper conductor 16 Sqmm 4 core LT 1100 volt grade complete all as specified and directed.

Supply, installation, testing and commissioning of the LT feeder pillar box with size 60cmx45cmx30 cm for water tight light (outdoor type), factory made free standing, floor mounting with four MS iron legs of 40cmx40cmx6mm, 45cm long size with suitable foundation (civil work complete) dust and vermin proof cubical type interlocking arrangement (IP-55 protection) fabricated with approximately 2 mm thick CRCA sheet including painted with anti corrosion coating & finnaly polyester powder coated of finite green fuly compartment with providing suitable size of 4 aluminum strip for bus bar and internally prewired with appropriate copper wire with all necessary accessories as an auto on / off switch complete all as specified and directed for the following :-

(a) Incomming :-

(i) MCB 63 Amps, Double pole, 230 Vollts with repturing capacity 16 KA - 01 No.

(v) Aluminium bus bar rating 100 Amps, single phase & neutral - 01 set

(vi) Chamber/Bracket for incoming & outgoing cable.

(b) Outgoing :-

(i) MCB SPN 20 Amps, 10 KA, 230 Volts - 04 No.

Disconnecting and taking down of wall mounted and ceiling mounted speakers any type from ceiling and wall and cleaning, servicing and keeping safely in custody of contractor to refixing the same as it is after completion of work at it's initial position including necessary connection with existing wires complete all as specified and directed

S&F MCB DB SPN 4 Way with metal single door, (IP-43 Protection) flush mounting epoxy powder control having 200 Amps rated bus bar complete all as specified and directed

S&F in repalcement of flexible copper conductor cable 1.5sqmm twin core for connection to wall /ceiling mounted speakers complete all as specified and directed

S & F in replacement of Surface mounting LED Integrated Aluminium Batten luminaire Polycarbonate co-extrusion tube for 20W LED light housing with engg-plastic end caps.Co-extrusion tube top part is made of polycarbonate material, and the diffuser is made of opal polycarbonate material with groove inside for PCB.LED populated on PCB comprising of LED’s connected in series parallel. Driver: Constant current LED driver. Fixture should have minimum system lumen of 2000lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 25K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >80,PF – 0.95 , THD <20%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 3kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer complete with including flexible wire complete all as specified and directed . Make - Bajaj Cat Part No - BCLAB 20W WH LED P / Crompton Cat Part No- LDL-20-CDL / Make - Wipro Cat Part no:LL20-281-XXX-65AL1

S&F in replacement of S&F LED Circular Recess mounting LED Downlighter of 32 Watt with Powder coated spun aluminium ring. LEDs module is mounted on extruded aluminum heat sink for better thermal management. LEDs incorporated in Aluminium anodised sheet for minimizing glare. Aluminium reflector is fixed with heat sink by SS clips.. Driver: Constant current LED driver. Fixture should have minimum system lumen of 3200lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700K with same lumens/w. CRI >70, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 2kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer suitable for POP or any type of false ceiling supplied with wedge bracket to fix in New POP or any type of false ceiling including cutting / grouting of any type of false ceiling to match with fitting and providing connections to the fitting complete all as specified and directed. Make - Bajaj Cat Part No - BCDLR 32W WH / Philips Cat Part No- RS378Z M102 D150 R-R AJU / Wipro Cat Part no-LD56-381-060-40-XX

S&F in replacement of 36W LED Surface mounted 2’x 2’ LED Luminaire having CRCA housing comprising of LED’s connected in series parallel. Opal diffuser fixed in separate white powder coated sheet steel frame. Opal diffuser frame is held in with housing by screws for easy maintenance. Driver: Constant current LED driver. Finish: White powder coated. Fixture should have minimum system lumen of 3600lm & minimum efficacy at System level >=100lumens/ watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT 5700-6500K with same lumens/w. CRI >80, THD <10%@ 240v ac. An operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 2.5kv, IP 20. BIS certification is required for LED Driver & Luminaire, OEM should have inhouse NABL Accrediated R&D and own luminaire manufacturing facility to provide LM79 report from in house NABL accredited lab & LM80 report issued by LED manufacturer complete all accessories including necessary connection of suitable size wire complete all as specified and directed. Make - Bajaj Cat Part No - BZSSQL 36W LED WHi / Crompton Cat Part No- LCTLSNE-36-FO-CDL / Wipro Cat Part no: CRCO10S036HP57G2

S&F in replacement of RJ 11 Telephone modular socket 1 Module suitable for connection of telephone complete all as specified and directed at site. Make : Model Crabtree of Havells / Model – Unica of Schneider / Model – Marius of Legrand

S&F in replacement of Cable TV modular socket outlet1 Module with grip suitable for connection of cable TV complete all as specified and directed at site. Make : Model Crabtree of Havells / Model – Unica of Schneider / Model – Marius of Legrand

Description of Work / Item(s)

Amount

M&L for Taking Down Existing Supply Air GI Ducts of following dimension duly marked/numbered with insulation complete Including Ducting Supports , rubber gaskets, elbows, vanes, & supports etc. carefully from any location at Manekshaw center and kept aside after removing of exiting insulation of any type (old/removed insulation should be deposited outside the defense premises and disposed safely by taking permission of MCD or through proper channel) in safe custody for refixing the GI Ducts with all accessories at their existing location complete all as specified and directed

(a) Ducts up to 750 mm

(b) All as per Srl item No 1(a) here-in-before but 751 to 1500 mm

(c) All as per Srl item No 1(a) here-in-before but 1500 to 2200 mm

M&L for Refixing the Supply Air GI Ducts of following dimension with insulation(new) including Ducting Supports, neoprene rubber gaskets, elbows, exhaust/toilet exhaust, vanes, & supports as per (IS 655) etc as retrieved against item No 1 above at their existing location/place as per numbering/marking at manekshaw center for satisfactory performance complete all as specified and directed by Engineer-in-Charge. Note:-1. Insulation work for old/new ducts will be measured and paid separately under relevant item. 2. Claims, hangers, supports, elbows, nut bolts & washer if required new will be measured and paid separately under relevant item.

(a) Ducts up to 750 mm

(b) All as per Srl item No 2(a) here-in-before but 751 to 1500 mm

(c)-All as per Srl item No 2(a) here-in-before but 1500 to 2200 mm

M&L for Taking Down Existing Return/Fresh/Toielt Exhaust air ducts of following dimension duly marked/numbered complete without insulation Including Ducting Supports rubber gaskets, elbows, vanes, & supports etc. carefully from any location at Manekshaw center and kept aside in safe custody for refixing the GI Ducts with all accessories at their existing location complete all as specified and directed by engineer-in-charge.

(a) Ducts up to 750 mm

(b) All as per Srl item No 3(a) here-in-before but 751 to 1500 mm

(c)- All as per Srl item No 3(a) here-in-before but 1500 to 2200 mm

M&L for Refixing the Return/Fresh air GI Ducts of following dimension including Ducting Supports , neoprene rubber gaskets, elbows, exhaust/toilet exhaust, vanes, & supports as per IS 655 etc as retrieved against item No 3 above at their existing location/place as per numbering/marking at manekshaw center for satisfactory performance complete all as specified and directed by engineer-in-charge. Note:-1. Insulation work for old/new ducts will be measured and paid separately under relevant item. 2. Claims, hangers, supports, elbows, nut bolts & washer if required new will be measured and paid separately under relevant item.

(a) Ducts up to 750 mm

(b) All as per Srl item No 4(a) here-in-before but 751 to 1500 mm

(c)- All as per Srl item No 4(a) here-in-before but 1500 to 2200 mm

M&L for Taking Down Existing Supply/Return Air Diffuser/Dampers/Grilles , of following size duly numbered/Marked carefully from any location at manekshaw center and kept aside in safe custody for refixing the Supply/Return Air Diffuser/Dampers ,at existing/required location complete all as specified and directed by engineer-in-charge.

(a) Diffuser/Damper of size 375x375 mm

M&L for Refixing the Serviceable supply/Return Air Diffuser/Dampers as retrieved against item No 5 above including neoprene rubber gaskets at existing/required location as per numbering/marking at manekshaw center for satisfactory performance complete all as specified and directed by engineer-in-charge.

(a) Diffuser/Damper of size 375x375 mm

(b) All as per Srl item No 6(a) here-in-before but 450x450 mm

(c ) All as per Srl item No 6(a) here-in-before but 600x150 mm

(d) All as per Srl item No 6(a) here-in-before but 500x500 mm

(e) All as per Srl item No 6(a) here-in-before but 900x200 mm

M&L for Taking Down Existing Side Grills, supply/return air grills, fresh air grills, of any size any shape duly marked/numbered carefully from any location at manekshaw center and kept aside in safe custody for refixing the Side Grills, return air grills, at existing/required location complete all as specified and directed

M&L for Refixing the Serviceable ,Side Grills, supply/return air grills ,fresh air grille, as retrieved against item no 7 above including neoprene rubber gaskets at existing/required as per numbering /marking at manekshaw center for satisfactory performance complete all as specified and directed

M&L for Supply and installation of thermal insulation material for non-exposed Ducts, chiller/hot water pipe lines with closed cell class 'O' nitrile rubber elastomeric insulation of density 40-60 Kg/m3 thermal conductivity of 0.033-0.038 W/mk and µ>=7000 (k-flex st) to be applied on ducts, chiller/hot water pipe lines using manufacturers recommended rubber based adhesive as per the approved specification the material should be from global approved & UL approved for old (refixed) & new ducts and chiller/hot water pipe lines as required at site complete all as specified and directed

(a) 19 mm thick for ducts passing through non-air conditioned space, chiller/hot water pipe lines

(b) 13 mm thick for ducts passing through conditioned space

M&L for Supply and installation of thermal insulation material for non-exposed Ducts, chiller/hot water pipe lines with closed cell class o nitrile rubber elastomeric insulation of density 40-60 Kg/m3 thermal conductivity of 0.033-0.038 W/mk and µ>=7000 and with factory laminated glass covering (k-flex ST IC CLAD) to be applied on ducts, chiller/hot water pipe lines using manufacturers recommended rubber based adhesive as per the approved specification the material should be fm global approved & UL approved for old(refixed) & new ducts and chiller/hot water pipe lines as required at site complete all as specified and directed

(a) 25 mm thick

M&L in replacement for Supply, fabrication ,Installation, Balancing and Commissioning and fabricated GSS sheet metal rectangular ducts/ elbows as per site requirement with supports as per IS 655-2010 complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as site requirements of following sheet thickness complete as required at site all as specified and directed

(a) 24 gauge ( thickness 0.63mm )

(b) 22 gauge ( thickness 0.8mm )

(c)20 gauge ( thickness 1.0mm )

M&L for Supply, fixing of powder coated extruded aluminum rectangular diffusers complete with black anodized extruded aluminum VCD (wherever specified), nuts, bolts, screws etc.complete old(refixed) and new as required at site all as specified and directed

(a) Supply air diffusers of required sizes with volume control damper.

(b) Return air diffusers of required sizes without volume control damper

M&L for Supply & Fixing of powder coated extruded aluminum supply & return grilles complete with nuts, bolts, screws etc. to make the system complete, complete old(refixed) and new as required at site all as specified and directed

M&L in replacement ducting supports, bracings, hangers,(as per IS-655) clamps and back plates fabricated from structural steel sections including nuts, bolts ,washers ,welding, bending cold or hot drilling holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat one under coat and one finishing coat of paint complete all as specified and directed

M&L for Supply, installation, testing and commissioning of flexible fire retardant canvas connector cloth complete all as specified and directed

M&L for taking down unfixed/damaged under deck insulation of any dia any shape for refixing the same at their existing location all as specified and directed by engr-in-charge.Note:-(old/removed insulation should be deposited outside the defense premises and disposed safely by taking permission of MCD or through proper channel)

M&L for supply & fix Under deck/floor insulation with closed cell nitirle rubber (class 0 ) of density of 40-60 Kg/m3 & thermal conductivity of 0.033-0.38 W/mK and with factory laminated aluminums foil having antimicrobial and antifungal properties as per specification .( K-FLEX ST ANTIMICROBIAL) all as specified and directed

(a) 25 mm thick

Taking down Damaged insulation any type from any size of chiller/ hot water pipe line at manekshaw centre and removing of exiting insulation of any type (old/removed insulation should be deposited outside the defense premises and disposed safely by taking permission of MCD or through proper channel) complete all as specified and directed

Note for above items:-

a.Photo graphic / records of each of ducts should be made by the contractor along with video graphic record of the complete ducting work before commencement of ducting works should be submitted by the contractor in triplicate .The rates are dammed to be included in quoted rate.

b. Each profile should be serially numbered and detailed record of same with regards to its exact location at site will be made by the contractor for ease zoning of the area should be done.

c. There is a possibility these consequent to structural repair work the space available for refixing of duct may get constrained. All out efforts will be made to fit in the existing duct sections .However in case it is impossible to retain existing sections new section will be provided at such location which be duly design by a competent AC duct designer for which the cost is deemed to be included in the quoted rates .

d. The responsibility for safe custody of dismantled ducts section and other items will rest with the contractor any damage caused during the course of mishandling/storage refixing will be the responsibility of the contractor and same will be made good at his own cost. Suitable temporary storage will be made by the contractor at his own cost. The cost is deemed to be included in the quoted rate

f. Existing old hangers will be reused and in case of new/additional and other hangers and fixing arrangements needed the cost for same is deemed to be included in the Quoted Rate.

g.Quantites considered are provisional and are on assessed basis.

h. All support for ducts should match IS 655 standards

Description of Work / Item(s)

Amount

Taking down the existing auditorium chair & refixing in the same after laying and fixing of the carpet at the floor , steps & necessary oiling , greasing & servicing & replacement of top cloth cover of the chair & ensure the chair is in functional state complete all as specified and directed

Supply and fixing of push back chairs ( 23 inches arm to arm) for auditorium complete all as shown in drawing and as specified. Make : Rana chairs , Usha Lexus , Saryu Seating Co. Location :- Zorawar

Supply and fixing of push back chairs (21 inches arm to arm) for auditorium complete all as shown in drawing and as specified. Make : Rana chairs , Usha Lexus , Saryu Seating Co. Location :- Ashoka

Description of Work / Item(s)

Amount

Dismantling floor ,hearth or wall tilling ,including glass mosaic tiles from water body including cement mortar bedding any thickness up to reaching green slab , removing rubbish off the premises complete all as specified and directed

The water proofing treatment on horizontal / vertical surfaces with provision of following items in stages complete all as specified and directed. (a) The cleaning and preparation of the substrate to which the masterseal HLM 5000 (BASF) / Nitoproof 600 (fosroc) / Roof seal flex (Dr.Fixit)/ waterproofing of M/s Sika India Pvt Ltd is applied must be carried out thoroughly to leave a sound base for the application. Any laitance present on the surfaces must be removed mechanically. Release oil and other contamination which may impair adhesion must be removed prior to the application of the primer. (b) Providing and laying 20 mm thick plastering in the CM 1:3 mixed with approved water proofing compound like Master pel 777(BASF) / Conplast WL (Fosroc) / Pidiproof LW ( Dr. Fixit) ( Integral water proofing compound confirming to IS 2645) over the coated surfaces including preparation of surfaces ,finishing ,curing etc ,all complete as per manufacture’s specifications and instruction and as directed . (c) Providing and applying Masterseal HLM 5000 (BASF) / Nitoproof 600 (Fosroc ) / Roof seal flex ( Dr. fixit) , a single component polyurethane based coating that cures by reaction with atmospheric moisture to form a tough but flexible waterproofing membrane . it is elastomeric , seamless waterproof membrane applied applied in 2 coats to a DFT of 1.2 mm thick having a elongation capacity of over 600% and with solid content more than 85 % applied on the RCC surfaces including priming ,crack filling ,grouting ,coving ,ponding etc complete . The material shall comply to – ASTM C 836 National std. of Canada 37.58-M86 by CGSB.

Note :- (1) The above treatment shall be water cured for seven days . Before laying shingles the sloped water body shall be sprinkled with water ,using aneled pump , continuously for 6 hours left for 1 hours then the RCC water body shall be stage passed by GE for efficiency of water proofing treatment . (2) The chemicals shall be applied only by specialist agency / approved approved applicator of the manufacturer . The specialist agency / approved applicator shall give necessary guarantee for ten years for the effectiveness of the treatment carried out . (3) Equivalent item of make Sika for water proofing compound may be approved by the GE if requested by the contractor with requsite proof of equivalent of the product. Location :- water body of Manekshaw Centre

Supply only glass mosaic tile, random mix, piece size20x20mm, 4mm thick and sheet size 327x327mm,joint gap 1.92mm,make-italia/bisajja/cube mosaic complete all as specified and directed.

Fixing and grouting of glass mosaic tile, random mix, piece size20x20mm, 4mm thick and sheet of size 327x327mm,joint gap 1.92mm by adhesive (cement polymer base) ,make-MYK LATICRETE/ KARKOL/ BALENDURA/ SIKA complete all as specified and directed.

Description of Work / Item(s)

Amount

Dismantling paver blocks in any position and of any description complete all as specified and directed

M&L factory made vibro compacted pre cast cement concrete 80mm thick ( Strength 350 Kg/Sqcm) inter locking glass moulded coloured blocks / pavers in any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade complete all as specified and directed

M&L factory made vibro compacted pre cast cement concrete 60mm thick inter locking rubber moulded coloured blocks / pavers in any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed

M&L for sand filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and directed

Laying only old paver blocks retrieved from item No 01 here-in-before laid over 50mm average thickness dry sand cushion for old paver blocks with plate vibrator etc complete all as specified and directed

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed

S&F factory made kerb stone of size 450 mm x 300 mm of thickness 100 mm fixed with cement mortar complete all as specified and directed

Description of Work / Item(s)

Amount

Supply and laying of the following size of GI pipe medium grade with all fittings laid in trenches/floor in old/new position including taking out the old unserviceable pipe complete all as specified and directed (a) 80 mm bore

(b) 50 mm bore.

(c) 40 mm bore.

(d) 25 mm bore

M&L CI foot valve flanged type including nuts bolts washers and rubbers 80mm dia confirming to IS-4038 and including taking out the old unserviceable foot valve and romoval from the site complete all as specified and directed

Supply and installation of flanged ends Water Meter woltman type, Class 'B' of following sizes including testing and making good connection with flanged ends, with gasket rubber sheet and nut & bolts etc ISI Marked fixing in horizontal/inclind/vertical position, including taking out unserviceable water meter complete all as specified and directed Note :- Flange joints including jointing materials shall deemed to be included in the unit rate of this item. (a) 50 mm bore

(b) 80 mm bore

(c) 100 mm bore

(d) 150 mm bore

Supply, installation and testing flanged ends strainer / dirt box 150 mm bore with stainless steel mesh suitable for cold water meter to avoid foreign material entering into meter and making good connection with flanged ends, with gasket rubber sheet and nut & bolts fixing in horizontal/inclind/vertical position complete all as specified and directed Note :- Flange joints including jointing materials shall deemed to be included in the unit rate of this item.

S&F gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed, bore of pipe of following sizes including taking out the old unserviceable items complete all as specified and directed (a) 25 mm dia

(b) 40 mm dia

(c) 50 mm dia

S&F in replacement of butterfly valve of following size/bore conforming to IS 13095 including taking out the old unserviceable items complete all as specified and directed. (a) 40 mm dia

(b) 50 mm bore

(c) 80 mm dia

(d) 100 mm bore

(e) 150 mm bore

(f) 200 mm bore

M/L CI non return valve without by pass arrangement confirming to IS-5312 Part-I PN 1.0 incl nuts, bolts washers and gaskets including taking outs old unserviceable NRV of following sizes complete all as specified and directed (a) 80 mm dia

(b) 100 mm dia

(c ) 150 mm dia

Supply and lay in replacement of MS Pipes heavy grade with all fittings laid in floors or fixed to walls and ceilings including welding, flange, fixing of pipe with necessary standard clamps structural steel support, cutting as required at site including taking out old pipe of following bore complete all as specified and directed :- (a) 200 mm

Supply, installation, commissioning and testing of LT feeder piller box of sutable size, indoor cubical type, floor mounted, vermin proof factory made of CRCA Sheet 2 mm thick, CPRI approved and MS angle of size 40x40x5mm having suitable legs, one side openable with locking and key arrangement with two Nos pad lock 50 mm make Godrej/Harison, powder coated with three phase, 415 volts, 50 Hz, AC supply RYBN insulated with sleeved insulation complete with multifunctional meter LED type by showing Amps, Volts, frequency including internal wiring with suitable size of PVC insulated copper conductor cable, glands, lugs for incomming and out going cables, PCC platform made out of 1:2:4 type B1 and pedestal of 30 cm height complete all as specified and directed and comprising of the following:- (a) Copper Bus bar fixed on epoxy insulators capacity 100 Amp and bakelite insulation sheet at the back with coloured tape-01 set (3 phases and one neutral) (b) autometic star - delta starter with contactor and over load relay suitable for 7.5 HP non clogging submersible pump - 02 Nos. (c) MCB (TPN) 63Amp -01 No

Supply, installation, commissioning and testing of LT feeder piller box of sutable size, outdoor cubical type, floor mounted, vermin proof factory made of CRCA Sheet 2 mm thick, CPRI approved and MS angle of size 40x40x5mm having suitable legs, both side openable with locking and key arrangement with two Nos pad lock 50 mm make Godrej/Harison, powder coated with three phase, 415 volts, 50 Hz, AC supply RYBN insulated with sleeved insulation complete with multifunctional meter LED type by showing Amps, Volts, frequency including internal wiring with suitable size of PVC insulated copper conductor cable, glands, lugs for incomming and out going cables, PCC platform made out of 1:2:4 type B1 and pedestal of 30 cm height complete all as specified and directed and comprising of the following:- (a) Copper Bus bar fixed on epoxy insulators capacity 100 Amp and bakelite insulation sheet at the back with coloured tape-01 set (3 phases and one neutral) (b) MCCB 100 Amp 25 KA - 01 No (c) autometic star - delta starter with contactor and over load relay suitable for 10 HP submersible pump - 01 Nos. (c) autometic DOL starter with contactor and over load relay suitable for 10 HP monoblock pump set - 02 Nos. (d) MCB (SPN) 32Amp -01 No

M&L Earthing with GI earth plate electrode of size 60cm X 60cm X 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using GI strip 32x6mm size . Earth strip to be connected by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 40mm dia 5 mtr long GI pipe connected to main switch board or main control board and GI pipe light grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover 50mm thick and PCC chamber pit with PCC 1:2:4 type C2 (including excavation and earth work disposal of surplus soil to a distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 5 of SSR Part-I complete all as specified and directed

Supply and laying earth contunity conductor or main earthing lead fixed to wall on batten or recess or chases or burried in ground or drawn in GI pipe etc as required all as directed for 8 mm dia steel wire/ galvanised iron strip complete all as specified and directed

S&F in repair framed work such as grills grating etc with end of bars shouldered and of revetted or forged in to spick framed guard bars barred iron door, ladders, framed balusters, walkways, railing, frame work of water tank/valve pit cover and similar work etc complete all as specified and directed.

S&F in replacement of autometic star - delta non clogging submersible pump starter complete with contactor(25A) and over load relay of range 17-25A for 5HP non clogging submersible pump complete all as specified and directed

S&F in replacement PLC for fire fighting panel complete all as specified and directed. Make :- Minilec or equivalent in L&T/ABB/LEGRAND/Schinder

S&F 4 way fire brigade Inlet Connection (ISI marked) including nut, bolt washer and rubber gasket including taking out old items complete all as specified and directed Make --- Safegaurd / Ge - Tech / Omexe / Super-xe

S&F 3 way fire brigade Inlet Connection (ISI marked) including nut, bolt washer and rubber gasket including taking out old items complete all as specified and directed Make --- Safegaurd / Ge - Tech / Omexe / Super-xe

S&F 2 way fire brigade Inlet Connection (ISI marked) including nut, bolt washer and rubber gasket including taking out old items complete all as specified and directed Make --- Safegaurd / Ge - Tech / Omexe / Super-xe

M&L fire hose cabinet (outdoor type) of size 0.60x0.45x0.90CM made out of MS sheet 3 mm thick complete 2 Nos fixing angle of size 50x6 mm including opening with doors, locking arrangement with mirror glass and painting with supper enamel paint grouting with PCC complete etc including taking out old items complete all as specified and directed

Taking down old unserviceable and Supply and fixing cotton synthentic fabric circular woven jacketted rubberised fabric fire hose RRL 15 Mtrs long with coupling Stainless Steel 63 mm size male and female instantenous type complete all as specified and directed . Make --- Safegaurd / Omexe / Super-xe (Note :- old material shall be deposited to MES store yard)

S&F instanteneous type Stainless Steel branch pipe 63 mm dia of suitable length fitted with 16 mm dia nozzle complete all as specified and directed Make --- Safegaurd / Omexe / Super-xe

S&F Fire hook with 10' bamboo handle complete all as specified and directed

S& F Fire bucket complete all as specified and directed

M&L painting on steel and iron surfaces with one coat of synthetic enamel paint as per existing colour scheme or pattern after preperation of old painted surface of any description over 10cm in width or girth complete all as specified and directed

M&L Prepration of existing painted steel surface of feeder pillar box/LT panel by scraping and cleaning the surface and applying two coat of synthetic enamel paint by spray painting to achieve glossy finish in approved colour/shades including patch work ,welding replacement of defected hinges inner/outer surfaces of feeder pillar box /LT Panel etc at service block complete all as specified and directed

S&F dewatering vertical submersible pump set single phase 230 volts, 50 Hz AC, auto level control float valve of cap 2 HP suitable for 10 mtr head and discharge 60 LPM with 1.5 sqmm 3 core copper cable including taking out old unserviceable submersible pump and deposited to MES store complete all as specified and directed

Taking down old unserviceable and Supply and fixing in replacement Gun metal air release valve, 25 mm bore as per IS complete all as specified and as directed.

Taking down old unserviceable and Supply & fixing of 15 mm dia Sprinkler glass bulb type standard response as PER IS-15106/TAC guidelines 68 degree rating pendent type complete all as specified and directed

M&L for repair of existing old damaged valves pit chambers having dimension 120 cm X 120cm x 120cm (internal height ) using PCC (1:4:8) type D2 (using 40mm graded stone aggregate for foundation 15 cms thick. brick wall 23 cm thick built in CM (1:4), 10mm thick rendering all around the brick with 1: 6 cement mortor, PCC (1:2:4) type B1 (using 20mm graded stone aggergate) as in coping for grouting MS frame including 03mm thick MS top sheet cover with locking arragnement, MS frame made out of 40 X 40X 6mm thick angle iron including painting the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer including necessary excavation in any type soil, returning, filling in and removal of surplus soil to a distance not exceeding 50mtrs all as specified and shown on drg No-=CWE(U) D-1/86 sheet No-1 and including demolition/ dismantling of exsiting valve chamber complete all as specified and directed

Servicing of filteration system for water bodies of capacity 10,000 LPH including cleaning of strainer, sand filter, cartridge filter, PVC coupler,PVC sockets etc complete all as specified and directed.

All as per serial item No 30 here-in-before but of capacity 19,000 LPH Notes for item Nos 30 & 31 :- (i) The rates quoted shall deemed to includes opening the filteration system of water bodies,replacing the unserviceable spare parts and re-assembling the same in original position. (ii) Cost of spare parts otherthen cartridge filter is deemed to includes in the quoted rates. (iii) Cartrudge filter shall be measured & paid separetely.

S&F in replacement of cartridge filter CF 100 complete all as specified and directed.

All as per serial item No 32 here-in-before but cartridge filter CF 50

All as per serial item No 32 here-in-before but cartridge filter CF 25 Make for item Nos 32 to 34 :- EMAUX or equivalent as approved.

Description of Work / Item(s)

Amount

Excavation in trenches not exc. 1.5 m wide and not exc 1.5 mtr deep in soft loose soil for laying / taking up/ taking down of cables and getting out and levelling of bottom suface to required level complete all as specified and directed

Returning filling in,. Including spreading, levelling,. Watering and well ramming soil in layers not exceeding 25 cm thick complete all as specified and directed

Removing excavated material (ie soil) from site to a distance n. exc 50 mtrs away and depositing where directed at a level n. exc. 1.5 mtr above the starting point complete all as specified and directed

M&L for river washed and screened, dry sand for filling in trenches below and around underground cables for cushioning of cables etc, complete all as specified and directed. Note : -Only Punned sand shall be measured and paid for.

Supplying and laying un-reinforced precast concrete cable cover class LV, type I, flat , size 250mmx150mmx40mm in trenches for cable protection etc complete all as specified and directed.

M/L in replacment GI pipe of size 40 mm dia light grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and directed.

All as per item No 6 herein-before but of size 80 mm dia

Supply , laying and testing cable XLPE insulated , screened , PVC bedded galvanised steel strip or wire armoured , electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm , 4 core including taking out of old unserviceable LT cable.

All as per item No 8 here-in-before but 16 Sqmm 2 Core

All as per item No 8 here-in-before but 70 Sqmm 3.5 Core

Dismantling of unserviceable steel poles /structs of any size complete all as specified and directed

Supplying and installation of hot dipped galvanized iron octagonal pole having 8 mtr height , wall thickness 3mm , top dia 70mm , bottom dia 130mm , size of base plate 225x225mm , 16mm thick , approx 300 mm long weather proof door opening should have an integral inbuilt looping box duly mounted with one No. MCB, SP, 10 Amp, one No. 63 Amp, 4 way heavy duty connector and earth stud including S&F of 3 core, 1.5 Sqmm PVC insulated and PVC round sheathed, copper conductor cable, 1100 Volts grade from MCB to street light bimetallic connection to be used wherever Al & Cu wire/busbar encountered at joints, factory made standard single /double arm bracket 1.2m long made of 40mm dia GI pipe medium grade , 04 Nos foundation bolt ,M20 threaded made to J shape 700mm long steel grade EN8 with nuts templates .Foundation of pole shall be of size 600x600mm and depth 1400mm buy using RCC 1:1:5:3 ,8 Nos 16mm dia tor bar as main bars and 8mm dia Tor bars strips @ 150mm c/c confirming to IS: 1786 latest edition. The foundation shall extend above surroundings ground/drive way level for 200mm and casted with 02 Nos 63 mm dia HDPE pipe for cable in and out as per site requirement complete all as directed. Note:- The cost of construction of foundation for pole including earth work, RCC , steel bars , strip , Fdn bolts , HDPE pipes etc are required at site is deemed to be included in the quoted rate. Make Havells/Bajaj/Surya/Cromption Greaves

Dismantling and taking down of unserviceable MH street light fittings from poles, unserviceable post top lantern fittings including GI pipe post & landscape luminaire( garden lights) fittings complete all as specified and directed.

S&F 120 watt new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source with toughened glass top cover.Top Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Device complete all as specified and directed. Make Havells Item Code No ENDURAPEARLMAGSL120WLED757PASYTOTGASTHO or equivalent in Philips/Crompton /Bajaj

S&F 35 W post top lantern having protection IP 65/66 complete all as specified and directed Make Havells (Item code No VICTORIAPT35WLED730PSYMTOTG) or equivalent in Philips/CG

S&F 3.5 M long post top light pole aesthetically designed decorative hot dipped galvanised mild steel step pole with grey powder finish , plasma cut & duly chamfered opening window of 300x110 mm for terminal connections & mounting accessories . Window cover is fitted with allen screws to the pole complete all as specified and directed Make : Havells or equivalent in Philips/CG

S&F pole base cover aestetocally designed decorative pole base cover, enhancing the apearance of the pole complete all as specified and directed Make : Havells or equivalent in Philips/CG. Note- The cost of excavation and PCC 1:3:6 , type C-1 for foundation required for post top light pole is deemed to be included in the quoted rate

S&F 8 W landscape luminaire( garden lights) having protection IP 65 complete all as specified and directed Make Havells (Item code No BAMBOOBLS8WLED830PSYMTOPC (0.6 M) or equivalent in Philips/CG Note- The cost of excavation and PCC 1:3:6 , type C-1 for foundation required for garden light is deemed to be included in the quoted rate

M&L for dismantling of old UNSV LT panal/ street light timer panel complete all as specified and directed

(b) Outgoing (i) MCCB 4 pole , 63 Amps,50 Hz,415 Volts, 25 KA with thermal magnetic release - 03 Nos (c) Platform of Panel. Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level.

(b) Outgoing (i) MCCB 4 pole , 125 Amps,50 Hz,415 Volts, 25 KA with thermal magnetic release - 04 Nos (c) Platform of Panel. Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level.

M&L Earth continuity conductor or main earthing lead laying to treanches & fixed to pole 4mm dia galvanised iron wire complete all as specified and directed

M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed and shown in electrical plate number 3 of SSR Part-I (2009). Note- (a) The unit rates quoted against this item shall be deemed to include the cost of excavation and earth work in any type of soil, common salt & charcoal dust in alternate layers, PCC 1:3:6 as in pit, precast RCC 1:2:4 type B-1 with necessary reinforcement as in cover & frame for pit, funnel, watering pipe 20 mm bore GI pipe light grade, protection pipe 15 mm bore GI pipe light grade etc. (b) The quoted rates shall also deemed to include the cost of earth test point and earth strip/GI lead wire and protection pipe upto 7.5 meter beyond the earth plates electrode

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 32 X 6 mm by means of nut, bolts, check nuts and washers of galvanised iron or steel and provision of charcoal dust and common salt packed all around the earth plate including necessary excavation and earth work in any type of soil and testing complete all as specified and directed and shown in electrical plate number 3 of SSR Part-I (2009). Note- (a) The unit rates quoted against this item shall be deemed to include the cost of excavation and earth work in any type of soil, common salt & charcoal dust in alternate layers, PCC 1:3:6 as in pit, precast RCC 1:2:4 type B-1 with necessary reinforcement as in cover & frame for pit, funnel, watering pipe 20 mm bore GI pipe light grade, protection pipe 40 mm bore GI pipe light grade etc. (b) The quoted rates shall also deemed to include the cost of earth test point and earth strip/GI lead wire and protection pipe upto 7.5 meter beyond the earth plates electrode.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 110 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed

Boring of hole under road/pavement/hard standing or any other situation by manual means and suitable for passing of GI pipe 40 to 80 mm bore and making good both ends all specified and directed

Chauhan Associates

Third Wave Services Pvt Ltd

pooja construction

Third Wave Services Pvt Ltd

Third Wave Services Pvt Ltd

Chauhan Associates

Chauhan Associates

pooja construction

pooja construction

Third Wave Services Pvt Ltd

Third Wave Services Pvt Ltd

pooja construction

Chauhan Associates

Third Wave Services Pvt Ltd

pooja construction

Third Wave Services Pvt Ltd

Third Wave Services Pvt Ltd

pooja construction

pooja construction

Third Wave Services Pvt Ltd

Bidder Name

Chauhan Associates

Third Wave Services Pvt Ltd

pooja construction