PROVN OF CHAIN LINK FENCING FOR NEW 80 SOA, SPECIAL REPAIR TO BUILDING NO 29(B) AND PROVN OF ENTRANCE GATE NEAR BLDG NO 85 AT MCEME UNDER GE MCEME SECUNDERABAD

Amount

Demolition of Lime concrete / Mud phuska / PCC of any description and in any position not otherwise specifically provided for renewal including removal of demolished material beyond the MD land to a distance exceeding 500mtr not exceeding 1.5KM completed all as specified and directed.

M&L 25mm thick PCC (1:2:4) type B0 using 12.5mm graded stone aggregate as in padding concrete (levelling course) on roof complete all as specified and as directed by Engr-in-Charge.

M&L Rendering 10 mm thick in CM (1:3) using water proofing compound as per manufacturer instructions as in roof padding and chajjas completed all as specified and directed. Note : Water proofing compound will be measured and paid separately.

M&L for applying bitumen primer 0.20kg / sqm providing and APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on including minimum 10cm side over lap and 15cm end laps applying a coat of blown grade hot bitumen 90/15 over the membrane @ 1.20 kg / sqm finishing with solar reflective bituminous aluminium paint @ 0.10 kg / sqm complete all as specified and as directed by Engineer-in-Charge.

Supply only integral water proofing compound completed all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing),and rubbish off the premises, etc complete all as specificed and as per directed by Engineer-in-Charge.

M&L for PCC 1:2:4, 25mm thick, type B0 (12.5mm graded agg) as as floor finishes, etc complete all as specificed and as per directed by Engineer-in-Charge.

M&L for Glazed ceramic coloured tiles 450x300x7mm thick, vertical surfaces such as dados, including 10mm thick rendering in CM 1:3 to receive tiles set and jointed in neat cement slurry and pointed in white or coloured cement to match, etc complete all as specificed and as per directed by Engineer-in-Charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exc 0.06 sqm but not exc 0.11 sqm in floors etc and jointed in neat cement slurry over and including 10mm thick screed bed or bedding layer of cement mortar 1:4 laying floor finishes and pointed in white or coloured cement to match , etc complete all as specificed and as per directed by Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutter from the frames ) not exceeding 1.5 Sqm each completed all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames ) exceeding 1.5 Sqm each but n.exc. 4 sqm each completed all as specified and directed.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc of size 105 x 60 mm completed all as specified and directed.

M&L PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in coping, filling steel frames etc including form work complete all as specifed and directed.

M&L Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M S Square tube, supplying and fixing in opening as per manufacturers instructions all as directed complete all as specified

M&L Factory made solid panel laminated PVC door shutter 30mm thick (style) consisting of frame made out M.S tube for top & bottom rails. M.S Frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled the stiles & rails with suitalble PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specifications & drawing complete all as specified

S&F 100 mm long butt hinges extruded aluminium alloy with brass/bronze hinge pin in lieu of mild steel min completed all as specified and directed.

S&F 150mm size aluminium anodised handles, fabricated type completed all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section completed all as specified and directed.

S&F 150 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F prepainted steel windows/ventilators ( ECO–4000 Series Windows (Double Rebate Windows) or equivalent) fabricated from roll framed sections made of galvanized steel colour coated/powder coated (Base steel as per IS-513 “D” quality galvanized as per IS-277 with zinc of 120 gms/Sqr. Mtr.) with total coated thickness of 0.58mm. Sections for Frame should be of 72x55mm, Section for Mullion should be of 72x50mm, Section for Shutter Frame should be of 47mm x 20mm, Section for Fixed Glass Bead should be of 12x12mm, and Section for Fly Mesh should be of 40x20mm Section for Frame Glazed Shutters and Mesh Shutters should be cut to length and miter joined with Polypropylene Corner Brackets, Mullion Section should be joined with Frame/Mullion using Mullion Cap Ethyl Propylene Damien Monomer (EPDM) Gasket should be used all around glass in shutter and Fixed Glass. Spoon Section should be used around Fly mesh to fix Mesh in Mesh Shutter including SS Pivot Hinges–1 set, Seccolor Handle & Seccolor Stay and 4mm Plain Float Glass and Stainless Steel 32 gauge Fly mesh of 25 holes per SqCM and powder coated Grill made of 10mm sq. MS Bars welded at 150mm c/c, 6x12mm MS flat and fixed to window frame with screws , complete all as specified and directed by Engineer-in-Charge. (Make : NCL/TATA/Equivalent)

M&L for 35mm thick flush shutter,solid core construction with block board core and plywood face panels,commercials type on both sides complete all as specified and directeb by Engineer in Charge

M&L for two coats of synthetic enamel paint over a coat of primer including preparation of new wooden surface of any description over 10 cm width and girth complete all as specified and directed.

M&L for rendering 10mm thick cement plaster in CM 1:6, on fair faces of brick work or concrete surfaces and finishing the surface even and smooth without using extra cement including taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water, etc complete all as specificed and as per directed by Engineer-in-Charge.

M&L for rendering 15mm thick rendering in two layers (5mm thick in CM 1:4 with using water proofing compound over 10mm thick in CM 1:6) on external surfaces of brick work or concrete surfaces even and smooth without using extra cement, including taking down cement plaster of any description incl raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as per directed by Engineer-in-Charge.

M&L for rendering 5mm thick cement plaster in CM 1:3 finished even and smooth without using extra cement on ceiling including taking down cement plaster of any description incl raking out joints, hacking for key, scrubbing down with water, etc complete all as specificed and as per directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over and including a coat of primer over and including of two coats of wall care putty complete all as specificed and as per directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of primer, etc complete all as specificed and as per directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of acrylic weather proof paint over and including a coat of primer over and including of two coats of wall care putty complete all as specificed and as per directed by Engineer-in-Charge.

S&F in repair vitreous china Orissa pattern squatting pan 580 x 440mm with integeral foot rests including P or S trap, complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China wash hand basin of size 550 x 400mm white flat back including chromium plated pillat tap, waste coupling, including brackets, PVC waste pipe, including cutting for and pinning in ends of brackets or errecting stand, complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, etc complete all as specificed and as per directed by Engineer-in-Charge.

S&F in repairs, Vitreous China ladies urinals (size 440mm x 350mm x 100mm), complete including providing and fixing plugs, securing urinal to plugs with and pointing around urinal bottom in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), etc complete all as specifed and directed.

S&F in repairs vitreous china EWC white including flush pipe, seat cover etc, including connection to drain (or out going pipe) and to flushing pipe anti syphonage pipes, etc complete all as specificed and as per directed by Engineer-in-Charge.

S&F in repairs 8mm thick glass corner, radius not exceeding 300mm dia with Stainless Steel brackets/rail as approved directed by Engineer-in-Charge

S&F in repair for, Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, etc complete all as specifed and directed.

S&F in repairs for PVC low level flushing cistern, white, 10 ltr. Capacity, complete with all internal accessories & fixed to wall & making good to wall surfaces incl. taking down existing flushing cisterns complete all as specified and directed.

S&F in repairs PVC connection pipe 15mm bore 600mm long complete all as specified and directed.

S&F in repairs 15mm dia bib taps, chromium plated fancy type, cast copper alloy with fancy type handle , screwed down , screwed for iron pipe or for brass ferrule with wall flange complete all as specified and directed.

S&F in repairs CP 15mm, stop valves/ angle cock, cast copper alloy with crutch or butterfly handle, screwed down, high pressure, screwed both ends for iron pipe complete all as specified and directed.

S&F rep CP brass tubular towel rail 600mm long 20mm dia 'D' type in repairs complete all as specified and directed.

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks three layered (cylindrical verical with closed top) hoisted and fixed in position all as specified in 1000 ltrs capacity with and including 15 mm HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule complete all as specifed and directed.

S&F in repairs Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

Taking up or down steel tubing & connections, 15 mm dia, etc complete all as specificed and as per directed by Engineer-in-Charge.

Taking up or down steel tubing & connections, 20 mm dia, etc complete all as specificed and as per directed by Engineer-in-Charge.

S&F GI Tubes, 'medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 15mm bore complete all as specified and directed.

M&L for cutting chases ,pinning in making good to facing where required of brick walls and pointed in cement mortar 1:3 for concealed water tubing etc cutting not exc 10 cm girth, complete all as specified and directed by Engineer-in-Charge.

S&F GI Tubes, 'medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 20mm bore complete all as specified and directed.

S&F in repairs Stain less Steel soap dish, any type, fixed to plugs with chromium plated brass screws, etc complete all as specified and as per directed by Engineer-in-Charge.

M&L for PCC (1:3:6) type C1 using 40mm graded aggregate as in plinth protection of average 75mm thick finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Demolition of cement concrete of any description in any position (Reinforced), complete all as specified & directed by Engr-in-Charge.

M&L RCC type B1 (1:2:4) using 20mm graded aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; exc. 200m thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide, rough finished surface.

M&L Mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking, bending spirally including mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L Mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality

M&L RCC type B1 (1:2:4) using 20mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified and directed.

Dismantling stone slabs and tiles laid dry and pointed of any description or thickness in floors, aprons etc. complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base etc., complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick screed bed or bedding layer of mortar in cement mortar 1:6 for lying floor finishes, complete all as specified and as directed by Engr-in-Charge.

M & L chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigments, complete all as specified and as directed by Engr-in-Charge.

M&L for Cement concrete type B- 0, 1:2:4 (12.5mm graded stone aggregate) for coping or chamfered on edges, including necessary form work etc complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches n.exc 1.50m wide and n.exc. 1.50m depth and getting out in hard/dense soil , complete all as specified & directed by Engr-in-Charge.

Returning, filling in incl spreading, leveling, watering and well ramming in layers n. exc 25cm all as specified.as in soft /loose soil, complete all as specified & directed by Engr-in-Charge.

Removing excavated materials n'exc 50 mtr and depositing where directed at a level n. exc 1.5 mtr above the starting point in soils, complete all as specified & directed by Engr-in-Charge.

M&L salt glazed stone ware drain pipes 150mm dia bore (Grade 'A' pipe) laid in trenches and jointed as specified including demolition and breaking up of old pipe, complete all as specified & directed by Engr-in-Charge.

M&L for Cement Concrete 1:3:6 type C-2 as concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150mm dia SWG pipe, complete all as specified & directed by Engr-in-Charge.

Taking down eaves, gutters and rain water pipes including all fittings any size and pattern complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed by Engr-in-Charge.

S&F in repair 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified & directed by Engr-in-Charge.

S&F in repair 75mm bore PVC (SWR) bend with oval access doors, complete all as specified & directed by Engr-in-Charge.

S&F in repair for PVC (SWR) vent cowl, bore of pipe in 75mm, etc complete all as specifed and directed.

S&F in repair for PVC (SWR) bends any radius, bore of pipe in 75mm, etc, complete all as specified & directed by Engr-in-Charge.

Demolition of brick work or stone masonary, built in cement mortar in any position or of any description, complete all as specified & directed by Engr-in-Charge.

M&L brick work with fly ash bricks built in CM 1:4 with modular bricks 'B' bricks straight or curved on plan exc 6 mtr mean radius, complete all as specified & directed by Engr-in-Charge.

M&L 15mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces of walls finished the surface even & smooth without using extra cement, complete all as specified & directed by Engr-in-Charge.

M&L PCC 1:4:8, type D2 (using 40mm graded stone aggregated) as in foundations, filling and mass concrete, complete all as specified & directed by Engr-in-Charge.

M&L PCC 1:2:4, type B1 (using 20mm graded stone aggregated) set in CM 1:4 as in benching to manholes/drain surface, complete all as specified & directed by Engr-in-Charge.

M&L PCC 1:2:4, type B1 (using 20mm graded stone aggregate as in pre-cast cover slabs for manholes incl necessary form work set in CM 1:4, complete all as specified & directed by Engr-in-Charge.. (Reinforcement will be measured & paid separately)

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/ dense soil, complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and exc 1.5m not exc 3m in depth & getting out in hard/dense soil

M&L RCC type B1 (1:1.5:3) using 20 mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L RCC type B1 (1:1.5:3) using 20 mm graded stone aggregate as in Columns , pillars, piers, posts and struts complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter Rough finished surfaces of concrete flat complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers,columns, and stanchions Rough finished surfaces of concrete Square, rectangular or polygonal complete all as specified and directed.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:4) complete all as specified and directed.

M & L Granite (of any type) work (table rubbed and polished) 19 to 20 mm thick in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, etc , etc complete all as specified and as per directed by Engineer-in-Charge.

S& F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165,etc, complete all as specificed and directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,Hard/dense soil., etc complete all as specified and directed.

S&F MS work as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

Supply only Chain link MS galvanisd fencing, using 5mm dia GI wire 50x50 mesh as in fencing complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,10mm dia neck, length of bolt n exc 5cm long complete all as specified and directed

M & L Preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specificed and directed by Engineer-in-Charge.

M&L cement Concrete type C2 1:3:6, using 40mm graded stone aggregate in surface channel and drains etc, complete all as specificed and directed by Engineer-in-Charge.

Material and labour for concealed point wiring with single core PVC insulated unsheathed 1100 volt grade cable with multistranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked of suitable dia conduit concealed wiring in walls/PVC conduit on wall including Tee, Junction boxes and provision of 2.0mm thick MS terminal boxes duly painted with red oxide metal primer and covered with 3 mm thick sheet cover of suitable size including suitable screws with washer for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to common earth dolly complete all as specified & as directed for One light point/fan point controlled by one, one way switch 5 amps, SP

All as per item No. 99 above but for One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board .

All as per item No. 99 above but for One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

Supply and fixing of Switch piano , single pole one way, flush type 5 Amps capacity 230 volts complete all as specified and directed.

Supply and fixing of socket outlet 2 in 1 multipurpose 2/3 pin 5 amps flush type complete all as specified and directed.

Supply and fixing of switch socket combination 2 in 1 multipurpose 2/3 pin 5 amps flush type complete all as specified and directed.

Supply and fixing of ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified and directed.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed .

Supply and fixing LED lights fitting 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed .

Supply and fixing lamp holder insulated body with back plate for angle batten fitting fixed with round block including LED bulb 9 W non dimmable type complete all as specified and directed

Supply and fix LED energy efficient security light fitting of capacity of 35 W including suitable dia light grade GI pipe bracket for fixing the light on wall all as specified and directed. NOTE : quoted rate included the suitble GI pipe bracket,nuts and bolts.

Supply and fixing Exhaust fan, heavy duty, 230/300 mmsweep metal body with louvers, AC single phase, 230 Volts, 1400 rpm and connecting up with and including necessary 3 core PVC insulated copper flexible cord of size 23/0.019 from exhaust fan to the ceiling rose including making hole in the wall and making good edges in cement plaster complete all as specified and directed.

Supply and lay on wall/in ground/on pole ISI marked XLPE insulated armoured, heavy duty, electric cable with aluminium conductors 1100 volts laid in trenches, floors, ducts, pipes drawn across the road/paths/drain/along poles/walls/floor/equivalent etc including jointing & testing complete all as specified of size 16 Sqmm , 2 core all as specified and directed.

Supply, spread river sand of approval in cable trenches providing for cable cushioning as directed. NOTE :- Punned thickness of sand only will be measured and paid.

Supply and lay PCC cable covers for LT cable protection, Class LV, Type 1 of size 250x150x40mm complete all as specified and directed.

Supply and fixing medium grade GI tubing of 32 mm dia for XLPE cable protection complete all as specified and as directed

Supply and fixing MCB double door DB SPN 8 way with 200 Amps busbar including removing the existing unserviceable one and making good the distrubed surface to match with the existing surface.

Supply and fix MCB SPN 40 Amps 240 volts for fixing on MCB DB complete all as specified and directed.

Supply and fix MCB SP 6 to 40 Amps 240 volts for fixing on MCB DB complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground to a depth not less than 2.25 m below ground level with top edge of earth plate not less than 1.5 m below normal ground level connected to GI earth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, checknuts and washers all as shown in Electrical Plate No.3 of SSR Part-I and connected to main switch board including excavation and earth work, PCC chamber in 1:3:6, RCC Cover in 1:2:4 type B-1 reinforced with 8 mm dia MS bars at 10 cm c/c, 20 mm dia medium grade GI pipe with funnel and wire mesh complete and watering arrangement all as specified. (Note: GI pipe 15mm dia, GI wire 4mm dia upto 7.5m deemed to be included in quoted rate.)

RAM CHARAN CONSTRUCTIONS

K LAKSHMAN SINGH AND CO

SAI RUPA CONSTRUCTIONS

SRI BHAVANI ENTERPRISES

VACON INFRASTRUCTURES