IMPROVEMENT TO LIVING IN SNCOs AND AIRMEN ACCN (PHASE I) AT AF STATION DEOLALI

Amount

(A)B/R ITEMS INCLUDING COMPOUND WALL, FENCING & GATE Dismantling single layer mangalore pattern or similar tiles in roofing including ridge tiles all as specified and as directed.

Dismantling of battens for tiles, shingles etc, of any size including tilting fillets spaced exc.15 cm complete all as specified and directed.

Dismantling unframed timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed.

Dismantling wooden scantling over 40 sqm in section and in any position all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semi corrugated etc.,) in roof coverings including ridges complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings (below or above ground level) not exceeding 15 cm thickness complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc all as directed.

Material and labour for brick work with old size fly ash bricks straight or curved on plan to any radius, built in cement mortar 1:6 all as specified.

Material and labour for brick work with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls,built in CM (1:4) all as specified and directed.

Material and labour for cement concrete (1:2:4) type B1, (using 20 mm graded stone aggregate) as seismic, plinth and similar bands, coping, kerbs, cills, steps, parapets, apex stones, bed plates, kerbs, railings up to 60 cm in height, water troughs and the like rounded or chamfered on edges including necessary form work all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement shall be cut as required to facilitate demolition) in ground floor (below or above GL) not exceeding 15 cm thickness all as specified and directed.

Material and labour for reinforced cement concrete 1:2:4, type B1 using 20 mm graded stone aggregate as in slabs supported on walls, beams, columns in floors, roofs, landings, balconies, canopies and in shelves etc., all as specified and as directed.

Supply and fix mild steel TMT bar of 10 mm dia and over cut length bent to shape required including cranking and binding with mild steel annealed wire not less than 0.9 mm dia complete all as directed.

Use and waste of formwork to sides and soffits of suspended slabs and similar works, flat, for a rough finished surface of concrete,all as specified & directed.

Supply and fix pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick (TCT) of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws complete all as specified and directed.

Supply and fix pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick (TCT) as in ridge of any colour having tensile strength of 550 Mpa as in ridge with self tapping screws complete all as specified and directed.

Supply and fix 0 .8 mm thick galvanised mild steel sheeting of class-3, hips, valley gutters, drip and straight flashings (length and grith as fixed) including cutting, bending to required shape & welding complete all as specified and directed

Material and labour for second class hard-wood in scantlings fixed as in girders, wall plates, purlins, rafters fixed with nails etc., complete all as specified and directed.

All as per item no. 20 hereinbefore but fixing only

Supply and fix rolled steel sections conforming to Fe-410 W (Gde E-250) of 'B' quality as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

Supply and fix mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut,exc 30cm long and dia of neck exc. 20 but not exc. 25 mm complete all as specified and directed.

Supply and fix mild steel, plain, black sheet 1 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel based surfaces exc. 10cm width or girth including preparation of new or previously untreated surfaces all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Material and Labour for anodised aluminium snap grid of size 605x605 mm frame work for false ceiling with aluminium angles of size 23.5 x 23.5 x 1.5mm fixed to wall with GI screws and aluminium tee section of size 37.5 x 37.5 x 1.5mm in main and cross runners fixed 60 cm c/c and tied to existing roof/truss/rafters with and including 4 mm dia GI wire of required length @ 1.2mc/c complete all as specified and directed

Material and labour for 4 mm thick non-asbestos fibre cement building boards (one side embossed design) fixed or laid /inserted to aluminium grid frame work in ceiling with clips all as per manufacturer's instructions complete all as specified and directed

Taking down carefully existing bitumen tarfelt including coba, plater of any description over the surfaces of roof, terraces including flashings and junctions of parapets/Curb walls etc and removing of the rubbish to a distance exceeding 500m but not exc 1.00 KM and depositing where directed.

Material and labour for 40 mm thick (average) PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding on roof , surface finished even and smooth without using extra cement all as specified and as directed.

Material and labour for rendering 15mm thick cement plaster in cement mortar 1:4 on concrete surface of roof/vertical surface upto 30 cm height and finished even and smooth without using extra cement using liquid WPC all as specified and as directed. Note : WPC measured separately as supply only.

Supply only approved liquid water proofing compound

Material and labour for cleaning the newly plastered surfaces of roof slab, Chajja, canopy, parapet etc., thoroughly with wire brushes and providing water proofing treatment all as specified here in after :- (a) Bituminous primer @ 0.30liter per sqm conforming to IS 3384-1986 (b) 3mm thick approved APP polymeric membrane minimum weighing 3 Kg/Sqm (one layer) laid by torch application method with over laps of 100 mm joints on traverse direction and 75 mm at longitudinal direction duly thermofused by flame torch all as specified in application manuel of the company (c) Painting with one coat of bitumin grade 85/25 @ 1.2 Kg/Sqm. (d) Applying two coats of aluminium paint @ 100ml/Sqm

Taking down cement or cement lime plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water etc all as specified and as directed.

Material & labour for rendering 5mm thick in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement all as specified and as directed.

Material & labour for rendering 15mm thick in cement mortar 1:6 on stone masonry or other than fair faces of brick work or concrete surfaces finished even and fair all as specified and as directed.

Material & labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and fair including WPC all as specified and as directed. Note : WPC measured separately as supply only.

Material and labour for applying three coats of white wash over newly plastered surface of ceiling including preparation of surfaces complete all as specified and as directed.

Material and labour for preparation of newly plastered surface on wall and applying two coats of distemper oil emulsion over one coat of wall care putty of not less than 2.0 mm thick including preparation of surfaces complete all as specified and directed.

Material and labour for applying two coats of cement based paint over a coat of alkali resistant primer over newly plastered surface of walls/ chajjas including preparation of surfaces complete all as specified and as directed.

Material and labour for preparing new /old wall surface including making surface clean, dry and free from any loose paint film, dirt, chalk, grease, fungus and algae and applying two coats of acrylic antifungal emulsion exterior weather proof paint on external surfaces, complete all as specified.

Material and labour for complete removal of existing treatment and applying two coats of distemper oil emulsion over one coat of wall care putty of not less than 2.0 mm thick including preparation of surfaces of old plastered surfaces of wall complete all as specified and directed.

Material and labour for complete removal of existing treatment and applying two coats of cement based paint over a coat of alkali resistant primer over old plastered surface of walls including preparation of surfaces complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

Material and labour for coloured (light shade) vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n. exc 0.36 Sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match and the shade of the tiles including 15mm screed bed or bedding layer in CM 1 : 6 all as specified and directed.

All as per item no. 45 here in before but of dark shade as approved.

Material and labour for coloured (light shade) vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n. exc 0.36 Sqm in skirting/ vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match and the shade of the tiles including 10mm screed bed or bedding layer in CM 1:4 all as specified and directed.

Material and labour for non-skid ceramic coloured tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc. 0.18sqm , laid in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match with over and including cement mortar screed of 15mm thick in CM 1:6 all as specified and directed.

Material and labour for non-skid ceramic coloured tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc. 0.18 sqm , as in skirting / dado/ risers of steps set and jointed in neat cement slurry and pointed in white or coloured cement to match with over and including cement mortar screed of 10mm thick in CM 1:4 all as specified and directed.

Material and labour for glazed ceramic coloured tiles (digital printed design) of size 450x350x7 mm on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with and over and including 10 mm thick screed bed in CM 1:4 all as specified and directed.

Material and labour plain cement concrete 1:2:4, type B-0 using 12.5 mm graded stone aggregate 25 mm thick as in floor topping all as specified.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar all as directed.

Material and labour for machine cut Cudappah stone slab flooring 20-25mm thick over , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Material and labour for 20 mm thick Granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite over 15 mm thick cement screed/rendering in CM 1:4 including roughening surfaces of old/new concrete floor/wall by picking, sweeping clean and washing down with water to remove dust etc., and brushing neat cement slurry with 3.00 kg per sqm all as specified and directed.

Material and labour for chamfering, splays or arris in firework for stone exceeding 15mm but not exc. 50 mm wide complete all as specified and directed.

Material and labour for 75mm thick PCC 1:3:6 mix type C1using 20 mm graded stone aggregate as in plinth protection and surface to be finished fair and even including joints at every 2.5 m and at all corners filled with 85/25 grade bitume and sand mixed in 1:2 ratio by weight complete all as specified and as directed.

Material and labour for machine cut kota stone in flooring 18-20 mm thick (Pre-mirror polished), over and including 20 mm thick cement screed base in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the floor including rubbing and polishing complete and moulding at edge if required all as specified and directed.

Material and labour for 18-20 mm thick Kota stone tiles (Pre-mirror polished), in riser of steps, skirting,dado etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles including rounding the edges of kota stone over and including 10mm thick backing coat in cement mortar (1:4), surfaces finished even and rough to receive tiles, all as specified and directed.

Material & labour for Makrana white marble tiles 30 cm x 20 cm x 2.0 cm thick machine cut, including cutting and polishing, set and jointed in neat cement slurry and pointed in coloured or white cement to match the shade of the tiles over and including 15 mm thick cement mortar 1:6 screed bed complete all as specified and as directed.

Forming grooves in Kota stone treads of 3mm wide and at a distance of 10 mm including making polished smooth round all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame ) n.exc. 1.5 sqm each complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame ) exc. 1.5 sqm but n.exc. 4.0 sqm each complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame ) exc. 4.0 sqm but n.exc. 8.0 sqm each complete all as specified and as directed.

Supply and fix pressed steel frame made out of 1.25 mm thick M S sheet and of size 125 x 60 mm for doors/ windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., and filling with PCC 1:3:6,type C-0 using 12.5 mm graded stone aggregate and painting with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete, as specified and directed.

All as per item no. 64 here in before but of size 105 x 60 mm.

Material and labour flush shutters, 35 mm thick solid core,construction, with block board core and plywood face panels, one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

Material and labour for factory made 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply & fix factory made solid panel PVC door frame of size 50mm x 47mm made out of 5mm thick wood grain printed PVC sheet & edges to printed to match with printed sheet, reinforced with MS Square tube, complete all as specified and directed.

Supply & fix factory made solid PVC moulded door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of pink primer on wood/ wood based steel surfaces of any description over 10 cm width or girth including preparation of new surfaces all as specified.

Material and labour for applying one coat of synthetic enamel paint on wood/ wood based steel surfaces of any description over 10 cm width or girth including preparation of old surfaces all as specified and directed.

Supply and fix 100 mm long cold rolled mild steel butt hinges, medium weight, cold rolled and fixed all as specified and directed.

All as per item no. 72 here in before but of stainless steel.

Supply and fix for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed all as specified and directed.

Supply and fix 150 mm size aluminium alloy handles, cast type anodised, ISI marked all as specified and directed.

Supply and fix 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts all as specified and directed.

Supply only pre -coated fancy type mild steel drapery rod as approved 25mm dia fixed with fancy type matching pair of brackets fixed with screw all as specified and directed. Note : Brackets will be measured seprately as supply only

Supply only fancy type brackets suitable for 25 mm dia pre-coated drapery rod all as approved and directed.

Taking up or down steel water tubing including connections 15 mm bore all as specified and as directed.

All as per item no. 79 here in before but of 20 mm dia pipes.

Supply & fix Galvanised iron water tubes 15mm bore medium grade with and including all fittings(ISI marked) complete and fixed to walls and ceiling or laid in floors all as specified and as directed.

All as per item no. 81 here in before but of 20 mm dia pipes.

Material & labour for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good cutting not exc 10 cm girth in brick/ stone walls complete all as specified and as directed.

Material and labour for rotational moulded polyethylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 25 mm dia ball brass valve with polythene float dismantling the old one complete all as specified and directed .

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position of 1000 litres capacity all as specified and as directed.

Supply and fix in repairs 15 mm bore gun metal, globe or gate valve cast copper chromium plated fancy type with iron wheel head , screwed both ends for iron pipe with crutch or buttrtfly handles all as directed.

All as per item no. 86 here in before but of 25 mm dia.

Supply and fix in repairs vitreous china wash hand basin, as approved white, flat back of size 550 x400mm excluding taps, chain and plug and porcelain stopper but including CI brackets and brass CP waste fittings 32 mm bore and PVC waste pipe of 32mm dia complete all as specified and directed.

Supply & fix in repairs 15 mm bore fancy type pillar cock, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed

Supply & fix in repairs stop valves/angle cocks, 15 mm bore, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions fancy type, chromium plated with long shank and cup (concealed type)and fixed all as specified and as directed.

Supply & fix in repairs bib cocks, 15 mm bore, fancy type, cast copper alloy chromium plated, with crutch or butterfly handle,wall flange long body,screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and directed.

Supply & fix PVC connections 15mm size with PTMT nuts of length 450 mmall as specified and as directed.

Supply & fix in repairs Vitreous china wash down water closet pan (pedestal pattern), of approved colour, complete including fixing to trap, Incl Supply and fixing of PVC seat and cover closed pattern with flat bottom and cover and mild steel chromium plated hinge device for pedestal pan and connecting to drain or out going pipe and to flushing pipe etc., complete all as specified and as directed.

Supply & fix in repairs Vitreous china squatting pan (Orissa pattern) of size 580x440mm, of white colour, front or back inlet and with integral foot rests including connecting to trap, flushing pipe etc., and PCC for making good the floor etc.,complete all as specified and as directed.

Supply & fix health faucet (ABS body) including 0.8 cm dia 1.2 m long flexible tube and wall hook alongwith MS anodised hanging device all as specified and as directed.

Supply and fix in repairs 10 litres PVC valveless symphonic action type flushing cistern high/low white complete with inlet,ball valve float and handle including brackets and 32 mm PVC bend and joint with WC complete all as specified and as directed .

All as per item no. 97 here in before but including taking down old ones as directed.

Supply & fix in repairs sheet glass assembly made of 5.5 mm thick sheet glass of 12 cm wide with chromium plated brackets guard and railing, 60 cm long all as directed and specified.

Supply and fix in repairs chromium plated shower rose, 125 mm dia with CP arms and swivel joints including fixing to steel pipe all as directed.

Supply & fix in repairs toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws all as specified and directed.

Supply & fix in repairs, Liquid soap container of PTMT as approved fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 105 gms) all as specified and as directed.

Supply and fix brass chromium plated tubular towel rail D type 20mm dia 600 mm long between flanges all as directed.

Supply and fix PVC (SWR) pipe 110mm bore of pipe waste and vent pipes etc.,single socket in any length with rubber ring joint, fixed to walls and floor all as specified and directed.

All as per item no. 104 hereinbefore but of 75 mm bore.

Supply and Fix 110 mm dia bore PVC (SWR) vent cowl all as specified and directed.

Supply and Fix 110 mm dia bore PVC (SWR) bend all as specified and directed.

Supply and Fix 110 mm dia bore PVC (SWR) bend with access door all as specified and directed.

Supply and fix 75 mm dia bore PVC (SWR) plain floor trap with grating including jointing with solvent cement complete all as specified and directed.

All as per item no. 109 hereinbefore but of 100 mm bore.

Supply and fix sinks with drainage board made of 1mm thick stainless steel sheet for kitchen or laboratery with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply & fix 40 mm dia (PVC) flexible waste pipe of suitable length for sink complete all as specified and as directed.

Supply and fix stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, orstainless steel wire staples all as specified & directed.

Material and labour for 25 mm thick veneered particle boards interior grade, solid core, general purposes type, with face veneers of type 'BB', fixed with screws to timber frame workcomplete all as specified and at location as directed.

Supply and fix Continuous (piano) hinges, mild steel, bright finish or electrogalvanished(Width of flap 30 mm) all as specified and directed.

Supply and fix 100 mm long hasp and staple , aluminium anodised, plate type including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply and fix floor door stopper, overall length of plate 140 mm, of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor all as specified and directed.

Supply and fix mild steel framed work such as grills, gratings door chowkats etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0all as specified and directed.

Supply and fix mild steel as in wind ties, hold fast and brackets for holding boarding etc., posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fix aluminium hat pegs, solid body, 125 mm to 175 mm complete as specified and directed.

Material and labour for drilling holes for insertion of pipes etc in granite /Cudappah including RCC slab not exceeding 25mm dia and not exceeding 100 mm depth complete all as specified and as directed.

Supply and fix aluminium powder coated door frame made of hollow extruded aluminium section and all as specified hereinbelow and all as specified and as directed complete: (a) Each door shall have 2 Nos disc or D type handles, 2Nos of 200 mm size aluminium tower bolts, one brass lock of 6 levers of approved make with keys in duplicate regulated by double action hydraulic floor spring (b)Shutter to be partly glazed with 5mm thick tinted glass and partly panelled with 12 mm thick pre- laminated particle board fixed with glazing clips, rubber beading/ gasket/ aluminium anodised beading complete. (c)Chowkat frame shall be of size 101.6 x 44.45 x1.55 mm (d)Shutter vertical/ stile shall be of size 85 x44.45 x1.56 mm (e)Shutter middle rail shall be of size 83.5 x44.45 x1.54 mm

Supply and fix anodized aluminium sliding window two/three (Bombay sliding window) made out of hollow extruded aluminium section as mentioned below and glazed with tinted glass 4mm thick fixed with glazing clips, rubber beding/gasket anodized aluminium beading screws and star lock type handles of size 75mm 2 Nos aluminium tower bolt 150mm long etc complete all as specified and directed with the following sizes:- (a) Shutter & bottom size 37.5x15x1.60mm thick & 40x18x1.09 mm thick (b) Shutter inner lock size 37.50x15x1.60mm thick, 40x18x1.00 mm thick (c) Shutter side (handle) size 37.50x15x1.36mm, 40x18x1.09 mm thick (d) Chowkhat bottom size 50.30x26x1.00mm, 92x31.75x1.10 mm thick (e) Chowkhat top & sides size 50.30x15x1.00mm, 92x31.75x1.05 mm thick

Supply and fix 10-12mm thick frosted toughened glass door with logo of Air Force and name as specified and directed with two nos of stainless steel handles for each shutter, 250mm long of decorative quality, floor spring of heavy duty in each shutter alongwith all fitting and fixtures and locking arrangements of approved make all as specified and directed.

Supply and fix double action floor door stopper/spring hydraulically regulated made up of minium 1.25 mm thick aluminium alloy sheet foundation bore, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty as in fixed including taking down and refixing aluminium shutter in the same opening.all as specified and as directed.

Supply and fix aluminium (die-cast body) door closer hydraulically regulated,designation No 3, universal type, suitable for door shutters of 700 mm in width and of weight not more than 35 kg complete all as specified and as directed

Supply and fix brass mortice lock 4 lever vertical type 100 mm size of approved make all as directed.

Material and labour for 75mm thick PCC 1:4:8, type D-2 using 40 mm graded stone aggregate as in sub base of floor and similar location all as specified and as directed.

Material and labour for chequered cement concrete tiles 25cm x25cm x 25mm thick, set, jointed and pointed in neat grey cement slurry in floors laid over and including 15 mm thick cement mortar 1:6 screed complete all as specified and as directed.

Material & labour for cutting openings through old masonry walls built in cement mortar for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing,fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises all as specified and as directed.

Material and labour for aluminium grill in panels as per decogrill model no DG-902 or equivalent with required aluminium framemof size 65 x1.5 mm thick including necessary joining cleats, rubber packing etc., complete as required all as specified and as directed.

Excavation in post holes (or similar holes) each not exc. 0.5 cum and getting out in any type of soil and removing excavated soil to a distance not exc. 50 m and making good the surfaces all as directed.

Material and labour for plain cement concrete 1:4:8, type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified.

Material and labour for plain cement concrete 1:3:6, type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified.

Supply and fix mild steel sections as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified.

Material and labour for mild steel round 10mm dia as in Tie bars of chain link fencing with screwed ends, nuts, washers and mild steel plates for walls, etc.and straining bolts confomiing to Fe290 Gde-E-165 all as specified and as directed.

Supply and fix Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, dia of neck5 to 10mm and length exc. 5cm and not exc. 10 cm all as specified and as directed.

Supply and fix chain link fencing made of 3.8 mm to 4mm dia galvanised mild steel wire and size of mesh 50 mm x 50 mm including line wires and binding wires etc., complete all as specified and as directed.

Supply and fix Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line wire to be measured), complete all as specified and as directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel based surfaces not exc. 10cm width or girth including preparation of new or previously untreated surfaces all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.5 meter wide and not exceeding 1.5M in depth for laying of water pipe lines and getting out of excavated material complete all as specified and directed

Material and labour for reinforced cement concrete M-25 (Design mix) using 20 mm graded aggregate mm graded broken stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc., all as specified and as directed.

All as per itm no. 142 hereinbefore but in columns, pillars, piers, posts and struts etc., all as specified and as directed.

Use and waste of formwork to sides of concrete foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc. for a rough finished surface of concrete,all as specified & directed.

All as per itm no. 144 hereinbefore but to sides of columns, pillars, piers, posts and struts etc., all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each, excavated soil in trenches after the pipes have been laid and tested complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.50 meter above the starting point complete all as specified and directed

Supply and fix mild steel TMT bar of 6 to 10 mm dia and over cut length bent to shape required including cranking and , bending spirally for hooping for columns as in stirrups, binding with mild steel annealed wire not less than 0.9 mm dia complete all as directed.

Material and labour for rolled mild steel sections conforming to Fe-410W(GdeE-250) quality A framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete all as specified and as directed.

Material and labour for 20 mm thick Granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite over 15 mm thick cement screed/rendering in CM 1:4 including roughening surfaces of old/new concrete floor/wall by picking, sweeping clean and washing down with water to remove dust etc., and brushing neat cement slurry with 3.00 kg per sqm all as specified and directed.

E/M ITEMS Note: RF & R & removal of excavated soil shall be measured under relevant items hereinbefore. Taking down carefully copper/aluminium point wiring (light, fan, socket or power etc) on TW batten/PVC casing caping, steel surface /PVC conduit including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Material & labour for taking down ceiling fan of any make/ sweep from it's position after disconnecting electric supply, cleaning, overhauling properly and painting with one coat of synthetic enamel paint by spray painting and re-fixing with new 3 core copper flexible wire of size 23/.0076 size from ceiling rose to fan all as specified and as directed.

All as per item no. 152 hereinbefore but of exhaust fan of any sweep/ make.

Taking down old unserviceable MCB DBs complete with MCBs, isolators etc., of any type and capacity from wall / ceiling etc., and making good the disturbed surfaces all as directed.

Taking down old unserviceable tube light/security lights/ garden lights/ gate lights etc., of any type/ make all as directed.

Material and labour for point wiring with two single core, PVC insulated, unsheathed, multi stranded bright annealed copper conductor cable, 1.5 Sq.mm 1100 Volts, FR grade drawn through and including heavy duty PVC casing and capping not less than 25 mm width and accessories surface mounted on walls, ceilings etc., on & including PVC box and plate for mounting switches, sockets, regulators etc and one run of 1.5 Sq.mm PVC insulated, unsheathed, multistranded, copper conductor cable FR grade as earth wire and connected to common earth dully complete for one light/ fan point all as specified and directed complete.

All as per item no. 156 hereinbefore but for one 3 pin socket out let 5 Amps on same board.

All as per item no. 156hereinbefore but for one 3 pin socket out let 5 Amps on independent board.

All as per item No 156herein before but two runs of copper condutor of size 2.5 sqmm as in socket outlet / power point 15 Amps. Note: The point wiring for power point will not be mixed with light/ fan point circuit in the same conduit / PVC casing caping.

Supply and fix switch piano type flush button 5 Amps single pole one way all as specified and all as directed.

Supply & fix socket out let 5 amps, 240 volts 2 in 1, 5 pin 5 Amps flush type complete all as specified and as directed.

Supply & fix socket out let 15 amps, 240 volts 2 in 1, 3 pin 5 and 15 Amps flush type complete all as specified and as directed.

Supply and fix ceiling rose of 3 phase/PVC/ polycarbonate, insulated body 65 x 50mm two or three terminals all as directed.

Supply and fix lamp holder PVC/ Polycarbonate type with back plate suitable for batten fitting Single Phase AC 230 Volts complete all as directed.

Supply and fix in replacement of stepped flush type electronic fan regulator flush type 2 modules 100 W, 240 V for 1200/1400mm sweep fans on the existing laminated sheet complete all as directed.

Supply and fix exhaust fans metal body 300 mm sweep 230V, BEE 5 star rating single phase, with louvers including making electrical connections with flexible cord three runs of twisted single core stranded copper conductor of size min 0.50 sq mm from ceiling rose to fan connector including connection to earth point all as specified and as directed.

Boring hole under the existing road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa workingpressure, minimum 0.6 mtr below the existing top surface GL complete all as specified and directed.

Supply and fix LED 5W lamps complete all as specified and as directed. Make: Havells Cat no. LEDADORE5WB22WW3STAR LAMP or equivalent in Philips / CG/ Wipro as approved

Supply and fix decorative ultra slim square profile linear laser ray lighting fixture extruded polycarbonate, environmental friendly, energy efficient ready to use pack 20 W LED 6000 K complete all as specified and as directed. Make: Crompton Cat no. LDLSR20-CDL or equivalent in Philips / Havells/ Wipro as approved

Supply and fix LED light fitting, 36W, 230 V reccessed mounting with CRCA powder coated body and high transluscent diffuser including frame and all accessoroes including driver and necessary electric connection etc complete all as specified and directed. Make : Crompton Cat no. LPCL-36-(2X2) or equivalent in C &S / Philips/Bajaj/ as approved.

Supply and fix LED Table/reading light fitting, 6W, 230v complete with all accessories and necessories electric connection etc complete all as specified and directed. Make : Havells Cat no. LHEXBVP7UN1W006 or equivalent in C &S / Philips/Bajaj as approved.

Material and labour for sub main wiring with PVC insulated un armoured heavy duty copper conductor 1100 Volts FR grade 2 runs of single core 2.5 Sq.mm cable and one run of 1.5 Sqmm copper earth wire for continuous earth fixed on wall/ceiling/ floor etc. drawn in PVC casing capping complete all as specified and as directed. Note :- Two runs of current carrying conductor and one run of earth conductor alongwith PVC casing/capping shall be measured as one unit.

Dismantling & taking down old unserviceable LT cable of any size type from wall/floor/ceiling and making good to disturbed surfaces all as specified and directed.

Supply and lay in replacement LT UG cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor of size 6 sqmm 2 core all as specified and directed.

Supply and lay in replacement LT UG cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor of size 25 sqmm 4 core all as specified and directed.

Supply and lay in replacement LT UG cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor of size 95 sqmm 3.5 core all as specified and directed.

Excavation in trenches in soft/ loose soil not exceeding 1.5 meter wide and not exceeding 1.5M in depth for laying of water pipe lines and getting out of excavated material complete all as specified and directed

All as per item no. 177 hereinbefore but in hard/dense soil.

Material and labour for fixing of DWC, pipes of flexible and capable of allowing deformation in diameter as well as in joints under external load & soil natural movement, socket and spigot joint with elastometric sealing ring and of highly corrosive resistant, impact resistant, chemical resistant, flexible, light weight and with high flow capacity of 135 mm dia with all required accessories such as coupler, elbows, etc., and with necessary joints as required for completion of work all as specified and directed.

Supply and lay in trenches/ passing through pipes LT UG cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor of size 4 sqmm2 core all as specified and directed.

Supply and fix sheet metal enclosure for DB’s with bus bar , MCB DB 12 way, 240 volts double door with detachable gland plate suitable for housing MCB SPN and SP alongwith 200 Amps copper bus bar complete all as specified and as directed.

Supply and fix sheet metal enclosure for DB’s suitable for housing MCB, SPN 8 way, 240 volts double door type, along with 200A copper bus bars, IP-44 protection all as directed.

Supply and fix sheet metal enclosure for DB’s suitable for housing MCB, SPN & SP 4 way, 240 volts double door type alongwith 200A copper bus bars, IP-44 protection all as directed.

Supply and fix MCCB incomer sheet metal enclosures Distribution board 415 volt, Vertical TPN 8 way with copper bus bar 250 A, for provision of MCCB of approved make as incomer and SP/TP MCBs as outgoing as per IS double door etc., complete surface/recess mounting IP-43 IK-09 protection complete all as specified and as directed . Note:(i) The cost of removing old panel box and making good surface to match with the existing shall be deemed included in the rate quoted. (ii) MCCB shall be measured and paid separately Make: L & T cat no. DBVTL00854 or equivalent in Havells/ HPL as approved.

Supply and fix MCB SP 6 to 30 Amps 240 volts breaking capacity10 KA all as directed.

Supply and fix MCB SPN 63 Amps 240 volts breaking capacity10 KA all as directed.

Supply and fix MCB TP 100 Amps 240 volts breaking capacity15 KA all as directed.

Supply and fix MCCB four pole 100 Amps 415 volts 25 KA, ICS=100% ICU with fixed thermal magnetic setting including spreader terminal/ thimble of suitable size and making connections complete all as specified and as directed.

Supply and fix MCCB sheet metal enclosure for DB’s suitable for holding MCCB of 100 t0 320 A four pole type including fixing accessories completeall as specified and as directed.

Supply and fix SPN sheet metal enclosure with a two pin and earth plug and socket complete with MCB 20 A 240 V completeall as specified and as directed.

Material and labour for providing earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 metres deep below ground level) surrounded with alternate layer of charcoal and salt of 15 cm thick, 3 feet x 3 feet all around the electrode as directed with top edge of the plate not less than 1.5 mtres below normal ground level,

connected to galvanised earth strip of size 25 x 4.0 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion including earthing pit in PCC 1:3:6 type C-0 & 40mm thick precast RCC cover in 1:2:4 type B1 reinforced with 8mm dia TMT bar @ 75mm c/c both ways with 02 Nos lifting handles of 12mm dia MS plain bar, GI pipe 20mm dia light grade with funnels & wire mesh for watering and 40mm dia light grade GI pipe for earth lead protection etc including necessary excavation and earth work in any type of soil complete all as specified and as directed. Note:- GI strip and protection pipe upto 7.5mtr is deemed to be included in the quoted rate.

Supply and fix GI strip of size 25 x 4mm as in earth continuity conductor for loop earthing including fixing arrangement on wall/ pole/ drawn into pipe or at location as directed complete as specified and as directed.

Supply and fixing security light New generation energy saving and environmental friendly long life exclusive innovative die-cast aluminium compact IP-65 roadway luminaire with high power LEDs as light suitable for highlighting architectural features/ area lighting along with electronic driver with all accessories including bracket made up of GI Pipe 40mm medium grade 1.5 mtr long made to shape with fixing clamps of MS Flat 40x6mm medium grade 1.2 mtr long made to light fitting complete all as specified and directed. Make : Havells Cat Part No. JETACOMPACTOFL50WLED757LTG or Equivalent in Bajaj or CGS as approved.

Supply and fixing in replacement LED post tops 40 W with die cast aluminium body and with clear toughened glass diffuser and IP-65 protection mounted on cast aluminium capsule long life aesthetically designed with symmetrical light distribution, spun aluminium land scape luminaire with all accessories complete all as specified and directed. Make : Havells Cat Part No. JETACOMPACTOFL50WLED757LTG or Equivalent in Bajaj or CGS as approved.

Supply & fix Galvanised iron water tubes 40mm bore light grade with and including all fittings(ISI marked) complete and fixed to walls and ceiling or laid in floors/ trenches with necessary bolts/ nuts/ washers etc., in the location all as directed.

Note:- The amount of schedule of credit on page No. 51 shall be deducted from the amount quoted against sch 'A' while deriving at the contract sum for accptance.

M/S MANISH CONSTRUCTION CO

M/S PRAMOD SURESHCHANDRA AHER

DARSHAN CONSTRUCTION Co.