Special repair of PHC Behal in Bhiwani Distt.. (Reinvite)

Amount

Earthwork in excavation in foundations, trenches of under ground structures, sullaged drains etc and other similar works in ordinary soil including dressing of bottom and sides, to correct levels and templates, cutting of trees and bushes, dewatering of rain water, diversion of traffic, fixing and maintenance of caution boards, and night singals, crossing over trenches for access to houses, watching , stacking of excavated soil, clear from the edge of excavation, and subsequent filling, where required around masonary, in 15cm layers, with compaction and disposal of surplus soil as directed within a lead of 30 meters for depth upto 2 meters below natural ground level (for public Health works only) (HSR 6.7)

Dismantling Roofing, (a) first class mud roofing (HSR 8.8,a)

Dismantling Roofing, (g) demolishing mud phaska in tile terracing (HSR 8.8 g)

Stripping and stacking slates or tiles of a roof (HSR 8.10)

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wallis not to be dismantled Door (HSR 8.18a )

Window & ventilator (HSR 8.18 b)

Dismantling cement conglomerate / terrazzo-floors 25 mm to 50 mm thick including concrete base (HSR 8.25)

Scrapping (c) Cement plaster (HSR 8.32 c)

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Cement concrete 1:8:16 with stone aggregate 40 mm Nominal sie in foundation and plinth. (HSR 10.28)

Cement concrete 1:4:8 with stone aggregate 40 mm nominal size in foundation & plinth. (HSR 10.39)

Cement concrete 1:2:4 with stone aggregate 20mm nominal size in foundation and plinth (HSR 10.41)

Precast cement concrete 1:1½:3 with stone aggregate 20 mm nominal size in Kerbs and the like itmes, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including form work, placing and fixing in position, complete at the ground level or in first storey. [HSR. 10.77 + 10.95 (a)].

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. [HSR. 10.82 + 10.95 (a)]

First class brick work laid in cement sand mortar 1:4 in foundation plinth. (HSR 11.4)

Terracing consisting of tiles 22.86 cm X 11.43 Cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc., (HSR 13.13)

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC pipe 6 kg. pressure.

(b) 150 mm dia PVC pipe 6 kg. pressure.

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.90]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC Bend.

Providing and fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJA-RIA, SOMANI, ORIENT, JOHNSONS & RAK (HSR 14.89)

Providing and fixing vitrified tiles of size 600x600mm of approved make in skirting/ dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJA-RIA, SOMANI, ORIENT, JOHNSONS & RAK (HSR 14.90)

12 mm Thick Cement Plaster 1:4 on the rough side of single or half brick wall. (HSR 15.5).

12mm thick cement plaster on walls (1:6). (HSR 15.7).

10mm thick cement plaster 1:4 under side of ceiling. (HSR 15.52).

Preparation of ply wood surface for painting inlcuding sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. Painting on wooden surfaces etc. (HSR 16.1)

Providing and Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2)

Providing and Applying Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3).

Painting two coats with plastic emulsion paint on walls on new work to give an even shade. (HSR 16.30)

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81). Through Rate

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non coniferous timber other teak, confirming to I.S. pecificationNo. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screw, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (a) 30 mm thick. [HSR 17.90 (a) - Note 1 under 17.18].

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (ii) 35 mm thick. [HSR 17.92 (ii) - Note 1 under 17.18]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Note:- reputed make such as Duro, Green, Kitply will be used as approved by Engineer-in-charge). HSR 17.93 (a) - Note 1 under 17.18]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (iv) 25 mm thick.

Providing and fixing aluminium work for doors windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming ot IS, 733 and IS: 1285 fixed with rawlplugs and screws orwith fixing clips or with expansion hold fasterners including necessary filling up of gaps at junctions, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat langle. Aluminium snap beading for glazing/paneling C.P. brass/ stainless steel screws, etc. complete.Shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC/neoprene gasket required including aluminium fitting. (HSR 17.96)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 grade I type II in paneling fixed in aluminium doors. Windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete. (b) Pre-laminated particle board with decorative lamination on both side(HSR 17.97,b)

Providing & fixing aluminium round shape handle of oputer dia 100mm screws etc. complete. (i) Anodized (AC-15) aluminium. (HSR 17.102 i)

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12).

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including Straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths /storeys/ basements etc. (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement). (HSR 18.22).

Supplying and fixing Glass panes including special metal sash putty of approved make. (b) glass panes 4 mm thic, exceeding 40 sq. dm areas. [HSR 18.30 (b)].

Pressed steel sheet frames (chowkhats) consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (a) door and window frame Size of 89 mm x 59 mm with 40 mm wide signel rebate. (HSR 18.34, a)

(c) door and window frame size 127 mm X 50 mm with 40 mm wide double rebate. (HSR 18.34 c)

Providing & fixing in position best indian make Indian type Orissa or orya water closet suite complete with 100mm H.C.I. 'P' trap and allother necessary fittings.Size 630 mm white (HSR 30.2 b i)

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Single trap syphonic (ii) Single Color. [HSR 30.5 (a) (ii)].

Providing & fixing in position best indian make Indian make a range of flat back or angular lipped front 465mm high in vitreous chinaware with one no. 5 ltrs capacity best Indian make C.I. automatic flushing cistern with fittings and flush pipe etc. complete. (HSR 30.19,i)

Providing & Fixing in position best indian make (ordinary) lavatory suites consisting of:- white (ii) Size 480 mm x 400 mm with one no. tap. [HSR 30.41(ii)].

Providing and fixing in position best quality Stainless Steel Sinks with Complete fittings as fully described in item No. 30.51. (b) 530 mm x 450 mm x 175 mm. [HSR 30.53 (b)].

Providing and fixing in position best indian make shower with 125 or 20 I/D in-let. (d) C.P. brass with revolving joint. [HSR 30.66 (c)].

Providing and fixing in position best Indian make towel rails fixed in with rawlslugs embedded in walls with C.P. Brass screws, complete in all respect including cutting and making goods the walls etc.: (a) 25 mm dia, C.P. Brass adjustable. (i) 750 mm long. [HSR 30.68 (a)]

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc. (a) C.P. Brass (i) Soap dish Large. [HSR 30.70 (a) (i)].

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75]. (a) Bib cock long body.

c. bib cock

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (i) Stop cock male and female [HSR 30.76 (a) (ii)].

ii) Concealed stop cock with flange.