SPL REPAIR OF BATHROOM AND TOILETS OF BLDG NO P-03 AND P-04 (SINGLE LIVING ACCN) UNDER GE (ARMY) SURATGARH AT SURATGARH MIL STN

Amount

Dismantling bricks (laid flat or on edge) or brick tiles on roof terrace, in floors, channels, kerbs, aprons etc laid dry or laid dry and pointed and removing from site complete all as specified & directed by Engineer-in-charge.

M&L for 40 mm thick PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in roof complete all as specified and as directed.

M&L for 10mm thick rendering in cement mortar (1:4) on brick walls/concrete surfaces mixed with water proofing compound as per manufacturer’s instructions including finishing the surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge. Note : - Supply only water proofing compound shall be measured and paid for separately under respective item of BOQ.

M&L for Roof treatment in as specified below and as directed (a) Cleaning the roof surfaces thoroughly using wire brushes to remove sharp projections, cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/ plaster etc complete. (b) Applying one coat of elastomeric PU based liquid membrane diluted with potable water in the ratio of 1:1 and apply @ 0.40 Kg/Sqm. (c) Laying polyster reinforced fiber net / 150 sqm Geotextile mesh, upto 300mm on walls. (d) Applying two coats of undilited PU based liquid membrane having Elongation more than 400%, Tensile strength more than 2N/mm2 and alkali & antifungal resistant maintaining thickness of 1.5mm with paint brush/ roller upto 300mm on walls. (e) The complete treatment to be carried out by authorised applicator of waterproofing manufacturer. MAKE Dr fixit/STP FOSROC/BASF or equivalent technocommercial make as specified in Appendix 'A'. Note : (i) The treatment shall be carried out as per manufacturer instructions and as directed by Engineer-in-Charge. (ii) The plan area of floor shall be considered for payment.

M&L Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with cementious grout of approved make, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Supply only water proofing compound, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar including all quions arches pillars etc complete all as specified and directed.

Dismantling of stone patti as in roof slab provided below roof sab of any description and thickness complete all as specified.

M&l for brick work with fly ash bricks old size straight or curved on plan exc 6m mean radius brick walls built in CM 1:6 complete all as specified.

M&L for brick work with fly ash bricks old sized straight or curved on plan exc 6m mean radius as in half brick walls built in CM 1:4.complete all as specified.

M&L for Jodhpur stone of roof slab self faced 7.5 cm to 10 cm thick 25 to 35 cm wide hoisted and set jointed and grouted in cement and sand mortar 1:6 complete all as specified.

M&L 25 mm PCC 1:2:4 using 20 mm graded aggregate over stone roof slab as leveling course complete all as specified and as directed by Engineer-in-Charge.

M&L for flush pointing in cement mortar 1:4 over stone patti in paving etc complete all as specified and as directed

Dismantling water tanks capcity exc 500 & n.exc.1000 ltrs and remove from site complete all as specified.

S & F Rotational moulded polyethylene water storage tanks of 1000 lites capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed

S & F Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20 mm complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises complete all as specified and as directed.

M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for glazed ceramic tiles (coloured) 300mm x 600mm x 7-8mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge.

M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (quare/rectangular) area of each tile exc 0.18 sqm but n exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the floor laid on vertical surface over 10 mm thick rendering in CM (1:4) complete all as specified and directed

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

M&L for rough cast finish plaster with a mixture consisting of crushed stone or fine gravel aggregate mixed with coarse sand and cement in the ratio of 1:1:1 over & including 12mm thick rendering in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls complete all as specified and directed by Engineer-in-charge.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faced brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar (1:3) on brick or concrete surface of ceiling, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for Machine cut kota stone slab flooring 20-25 mm (with all edges at rt angle to each other) thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing ( Bees wax) complete all as specified over 15 mm thick screed bed in CM 1:6 complete all as specified and as directed by Engineer-In-Charge.

M&L for machine cut kota stone 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing(Bees wax) complete all as specified.

M&L Granite 20 mm thick of any type work table rubbed and polised in steps,jambs,pillars,window cill, cooking plateforms and like in cement mortar 1:4 including pointing cement mortar 1:2 using marble dust with admixure of pigments to match with shade of granite over 15 mm thick screed bed of CM 1:6 complete all as specified and as directed.

Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down steel window / ventilator of any description and of any type with or without guard bars and making good the disturbed portion complete all as specified and directed by Engineer-in-charge.

M&L for Powder coated window frames ,other sections for doors , windows , ventilatorswith one or more rebates , channel for sliding shutters , grills etc including jointing cleats for fixing etc , complete all as spfd .

M&L for Powder coated aluminium (minimum thickness of powder (coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

M&L for sheet glass 5 mm thick ordinary quality and glazing fix with galzing clip or with oil putty square/ractangle not exc.0.5 sqm in each pane complete all as specified.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified.

Taking down or up, 15 mm bore galvanised steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engineer -in-charge.

Taking down or up, 20 mm bore galvanised steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engineer -in-charge.

Supplying and laying of 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified.

Supplying and laying of 25 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified.

S&F of 20 mm outer dia CPVC Brass Elbow fittings complete all as specified

S&F of 20 mm outer dia CPVC Brass Male Brass Threaded Adaptor (MTA/ MBTA) fittings complete all as specified

S&F of 25 mm outer dia CPVC Brass Elbow fittings complete all as specified

S&F of 25 mm outer dia CPVC Brass Male Brass Threaded Adaptor (MTA/ MBTA) fittings complete all as specified

Supplying and laying of CPVC pipes SDR 11 outer dia 25 mm & Plain CPVC SDR 11 fittings in trenches complete all as specified.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).including dismantling existing wooden/Iron /stone chowkhats complete and making good existing disturbed surface with CM 1:3 complete all as specified and directed by Engineer-in-charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125x65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).including dismantling existing wooden/Iron /stone chowkhats complete and making good existing disturbed surface with CM 1:3 complete all as specified and directed by Engineer-in-charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S& F for 30 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S& F for 35 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

M&L for factory made 2nd class hard wood 35 mm glazed and skelton shutter open rebated and prepared to receive glass,gauge etc.(w/o sash bars)edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc.as spcd. Clause 8.20(a) supplied and fitted to chowkats complete all as specified and as directed.

Demolition of cement concrete unreinforced of any description complete all as specified and directed by Engineer-in-charge.

Demolition of reinforced cement concrete of any description complete all as specified and directed by Engineer-in-charge.

Supply and fixing of SS butt hinges medium weight 100 mm long fixed to steel /angle iron/wooden frame by welding/fixing ,if required complete all as specified.

S&F SS barrel tower bolt of 150 mm complete all as specified and as directed.

S&F 250 mm SS sliding door bolts, plate type with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F Stainless steel handles of 150 mm complete all as specified and directed.

S & F Stainless Steel barrel tower bolt of 200 mm complete all as specified and directed.

S&F stainless steel tower bolt of 100 mm size complete all as specified and directed.

S & F Stainless steel handles of 150 mm complete all as specified and directed.

S& F as in repair 20 mm dia decorative stainless steel curtain rod including bibs, bracked complete all as specified.

S&F as in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge.

S&F as in repair Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. with & including WC seat cover closed pattern with flat bottom and cover, , pneumatic type capacity 10 litre including chrome finish dual flush control plate, flushing pipe and fixing bracket complete assembled with necessary fittings and fixtuers including necessary brick work and plastering for fixing the concealed cistern complete all as specified & as directed by Engineer-in-charge. Make:- Cat Part No. CASA "C022W Closet 680x365x780mm) & C022Y Cistern Set with Dual flush fittings of Parryware or HINDWARE QUED/JAQUAR equivalent in approved makelist as specified and as directed by Engineer-In-Charge.

S&F as in repair Spray Jet brass cromium plated fixed complete all as specified and as directed

S&F in replacement Counter oval type wash basin white colour of size 520 x 440 x 180mm including 32 mm dia PTMT waste coupling wastage chain with plug and procelain stopper complete all as specified and directed by Engineer-in-Charge. Make :- Jaquar Cat Part No CNS-WHT-705 /HINDWARE QUED/Parryware or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair vitreous china half stall type, flat back urinal of size 535 x 340 x 355mm, with grating and union for discharge pipe (excluding flushing cistern, flush and waste pipe) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe, chromium plated urinal spreader including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and directed by Engineer-in-charge.

S&F as in repair chromium plated Soap dish holder including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge. Make: Paryag Cat No BA-5S or Johnson or Hindware or equivalent technocommercial make as specified in Appendix 'A'. .

S&F as in repair stainless steel peg set with 06 No of hooks mounted on SS plate 4mm thick fixed with Cp brass screws complete all as specified and directed by Engineer-in-Charge.

S & F as in repair glass corner of size 300mmx300mm with 5.5 mm thick glass and steelness steel clip and steelness steel railing allround the shelf complete all as specified and directed by engineer in charge .

S&F in repair PVC valve less, symphonic action type, flushing cistern, low level white with inlet, ball valve, float and handle including brackets 10 litres complete all as specified & directed by Engineer-in-charge.Make :- Jaquar /HINDWARE QUED/Parryware or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450 mm complete all as specified & directed by Engineer-in-charge.

S & F in repair angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 20 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Shower 100 mm x 100 mm with Arm 15mm size ,195 mm long with bend of 45 degree with flange of PTMT any colour complete all as specified and as direcetd

S&F as in repair angle valves one way/2 way cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F as in repairs for CP , fancy type pillar cock 15 mm swan neck of complete fixed with necessary fittings complete all as specified and as directed by Engineer-In-Charge.Make :- Johnson/HINDWARE QUED/Parryware or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge.

S&F as in repair waste pipe 38/40 mm for sink with waste coupling complete all as specified & directed by Engineer-in-charge..

S&F as in repairs bib taps long body cast copper alloy chromium plated fancy type 15 mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed by Engineer-in-charge.

S&F as in repair Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 20 mm fancy type chromium plated concealed type fixed in repair complete all as specified & directed by Engineer-in-charge.

Dimantling pipes of any description fixed to wall or laid under floor complete all as specified & directed by Engineer-in-charge.

S & F PVC (SWR) pipes bore 110 mm single socketed in any length with rubber ring joints fixed to walls including including low carbon hot roll gauge corrected oil pickled & drawn pipe supporting clamping system 32x3mm with rib and notch are hot dip galvanised and Zn, Al flake coating with necessary clamps to fix and hold pipe complete all as specified and directed. (Note: Detail of Pipe supporting system is all as per Drg NO -BTD-916).

S&F PVC (SWR) pipes bore 110 mm single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed by Engineer-in-charge.

Supply and fixing PVC (SWR) bends any radius bore 110 mm provided with access door complete all as specified & directed by Engineer-in-charge.

PVC (SWR) pipes bore 75 mm single socketed in any length with rubber ring joints fixed to walls including supporting clamp including low carbon hot roll gauge corrected oil pickled & drawn pipe supporting clamping system 32x3mm with rib and notch are hot dip galvanised and Zn, Al flake coating with necessary clamps to fix and hold pipe complete all as specified and directed. (Note: Detail of Pipe supporting system is all as per Drg NO -BTD-916).

S&F PVC (SWR) pipes bore 75 mm single socketed in any length with rubber ring joints fixed to floor complete all as specified.

S & F PVC (SWR) bends any radius bore 75 mm provided with access door complete all as specified.

S&F 75mm bore PVC (SWR) junction,single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge"

S&F 110mm bore PVC (SWR) junction,single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge"

S&F 110mm bore PVC (SWR) reducers 110mm to 75mm complete all as specified and directed by Engineer-in-Charge

S&F 75mm bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge

S&F as in repair 75mm dia PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

M & L for preparation of newly plastered surfaces of wall & applying two coats of Interior emulsion paint by Roller or Air Spray over 1 mm thick wall care putty (Multipurpose mixer shall be used for uniform and proper mixing of putty) complete all as specified and as directed by Engineer-in- charge. (Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or equivalent in makes mentioned in Appendix 'A' here-in-after.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, filling cracks with wall care putty etc and applying two coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying two coat of white wash complete all as specified & directed by Engineer-in-Charge.

Material & Labour of preparation newly plastered and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-Charge. (Make :- Apex Ultima (Asian Paint), Weather Coat anti dust ( Berger Paint ), Excel No Dust ( Nerolac) or equivalent Technocommercial makes mentioned in Appendix 'A' here-in-after.

M&L for complete removal of existing treatment from old plastered surfaces of wall, using mechanical grinding machine and washing of old surface with water of wall, preparation of surfaces including filling of cracks and two coats of 100% premium Acrylic emulsion paint by using roller having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including one coat of primer applied @ 0.9 litre / 10sqm as per manufacturer instruction complete all as specified & directed by Engineer-in-Charge. (Make :- Apex Ultima (Asian Paint), Weather Coat anti dust ( Berger Paint ), Excel No Dust ( Nerolac) or equivalent Technocommercial makes mentioned in Appendix 'A' here-in-after.

Excavation in trenches, n. exc. 1.5 m wide and n. exc 1.5 m in depth; for foundaton, etc. or for shafts, well, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out complete all as specified & directed by Engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified & directed by Engineer-in-charge..

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.50 m above the starting point in soils complete all as specified & directed by Engineer-in-charge.

M&L for Cement concrete 1:4:8 type D2(40 mm graded stone aggregate) in foundation filling and mass concrete complete all as specified & directed by Engineer-in-charge.

M & L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in bed to drain pipe including forming cradles for 150mm dia of pipes and tested complete complete all as specified and directed by Engineer-in-Charge.

S&F DWCPE (SN8) pipe 150 mm dia (inner) as per IS-16098 (Part-II) laid in trenches or in floor on moorum bed to required shape including all necessary accessories / fitting / jointing / rings, joiting and testing including 100mm thick PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified & directed by Engineer-in-charge. Note :- laying of pipe will be made slope as directed by Engineer-in-charge.

M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified and directed by Engineer-in-charge. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

M&L brick work in cement mortar (1:4) using old size fly ash brick in walling, straight or curved on plan exc 6m mean radius complete all as specified & directed by Engineer-in-charge..

M&L for 15mm thick rendering in cement mortar (1:4) on brick walls/concrete surfaces mixed with water proofing compound 3% by weight of cement finished as per manufacturer’s instructions including finishing the surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge. Note : - Water proofing compound shall be included in this items. Nothing extra shall be paid on this account.

M&L for cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, coping, parapets and railing upto 60cm height, copings bed block, roof kerbs or mud stops, kerb stone, kneelers, apex stones, bed plates, surface channels and drains, benching, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for providing precast ce- ment concrete 1:2:4 type B1 using 20mm graded aggregate in window or door cills, lintels, bressumers, steps, quoin 12.blocks (for use with masonry), string courses,manhole cover , kerb stone, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), withplain fair faces,including chamfers, weatherings,throat- ing etc. and setting in mortar 1:6 complete with joints to match complete all as specified and as directed.

M&L for mild steel steel TMT bars 6mm to 8mm dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia complete all as specified & directed by Engineer-in-charge.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete ,using extra cement ,incl forms moulds ,mitered/stopped ends etc complete all as specified & directed by Engineer-in-charge.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified & directed by Engineer-in-charge..

S&F 150 mm Salt-glazed stoneware gully traps, square or round mouthed, type `P' complete all as specified.

Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 120 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on the same board with other switches.

All as per serial item No. 120 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on independent board.

All as per Srl item No. 120 above, but wiring with cable of cross sectional area 4 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 6 pin, 5/15 Amps on independent board including 4 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular switch piano 16 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular socket 2 / 3 pin, 6 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular socket 6 pin, 6/16 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge.

S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge. . Make :Havells (Crabtree)/Legrand/Legrand or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge.

S&F Energy efficient decorative ultra slim, prewired, lumiline 10 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W010/Crompton Cat Part CCS-103-10-65-SL-DP-NWH/Wipro Cat Part D531065 or equivalent cat part of Make as specified in Appendix A".

S&F Energy efficient decorative ultra slim, prewired, lumiline 20 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W020/Crompton Cat Part CCS-103-20-65-SL-DP-NWH/Wipro Cat Part D532065 or equivalent cat part of Make as specified in Appendix "A".

Supply and fixing LED lamp minimum 3 star rated 10W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.90 (e) CRI : Morethan 80 . Make :Wipro/Philips/Halonix or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair flush mounting factory made SPN DB 8 way, 240 Volt, Single door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge.

S&F MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F as in repair MCB 40-63 Amps, Single Pole & neutral 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F in replacement Sub main wiring complete with 2 single core 6 Sqmm (Nominal area) multi stranded copper conductor PVC insulated unsheathed cable FRLSH drawn in and including heavy duty PVC conduit ISI marked not less than 25mm dia concealed including single core multistranded copper conductor 6 Sqmm size cable as earth continuous wire drawn in same conduit complete all as specified and directed by Engineer-in- charge Note : Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittings shall be measured as one length.

SHIVA BUILDERS (BID ID -3501889)

PACHAR BROTHERS (BID ID -3501350)

AK CONSTRUCTION (BID ID -3501855)

J AND K CONSTRUCTION CO (BID ID -3495224)