Construction of Knowledge Centre at Lakshimipathy nager Ward no B, survey No-49,TS No 149 in Panruti municipality - Type 2

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS 20B and Sand, silt or other loose soil, wet sand, silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and completed, cleaning and levelling the site etc., complete - Footings - First Depth Upto 2.00M For Foundation first depth

Plinth Beam

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm.thick well rammed watered and compacted - etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hand broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted,etc., complete complying with standard specfication.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Column

Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials) Upto basement

Above basement Ground Floor

For first floor

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Supplying and filling the basement with Good well gravel filling in layers of not more than 15cm thick well rammed watered and compacted - etc., complete complying with standard specification.

Brick work in CM 1:5 (one cement & Five sand) using II class ground moulded bricks of size 9"X43/8"X 23/4" standard specification including finishing, curing, etc., complete complying with standard specification (Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost)- Upto Basement

Ground Floor

First Floor

Brick Partition Walls using III class ground moulded country bricks of size 8.75"X4.25 " X 2 3/4" in C.M 1:3 using hoop iron reinforcement,if found necessary standard specification including finishing, curing,etc., complete complying with standard specification - 10 sqm

Plastering with cement mortar 1:5 (One cement and five sand) 12mm thick in all floors including cost and conveyance of all materials to site etc,complete as per standard specifications

Special ceiling plastering in all floors and finishing the exposed surface of RCC items of work such as slab, beam, sunshade, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 (One cement and three sand) 10mm thick including hacking the surfaces and providing cement mortar nosing, beading for sunshade, staircase, step, landing slab etc., including neat finishing and curing etc., complete complying with standard specification and as directed by the departmental officers

Joinery (SH: - 5.0 - JOINERY & PARTITION WORKS ) Providing and fixing I Class Teak Wooden Frame & Shutter (Pannels) as per the drawing for Door, windows & ventilators with necessary fixtures and accessories approved by the Architect and client & other sections of approved make confirming to IS fixed with rawl plugs & screws or with fixing clips including necessary filling up of gaps at junctions, at top, bottom & sides, with 4mm glass, all complete as per architectural drawings & directions of Engineer- in-Charge at all levels.(glazing & panelling to be added in the rate). Cost Including spray painting, etc.

Supplying and Installing Metal False Ceiling using Fire Retardant Galvanized Steel Sheet Plain lay in tile size 600mm x 600mm, 0.5mm thick, powder coated on external surface and shall have flange on all four sides to rest on the exposed grids. The system to give 600mm x 600mm centre to centre 'T'. The 'T' shall be not be dipped GI Tee Section 3600mm long main Tee. 24mm wide and cross Tee panels are formed by running main runner of 'T' section of size 30mm x 24mm powder coated at bottom at intervals with powder coating at bottom. Necessary provision of inter locking of 'T' section are made at required intervals not exceeding 1200mm. The main runners are suspended from the ceiling by means of 4mm dia. GI rods fixed to the ceiling using anchor fasteners of 50mm x 8mm size with nylon inset and hooked to the main rubbers using clips. The last hangers at end of each rubber should not be greater than 600mm from the adjacent wall. The last panel shall be placed at the side wall using edge profile 'L' Angle of size 20mm x 20mm and fixed to the side wall the false ceiling should be fixed of same level and should present a neat look (SOR 2023-2024 P.72 , Sl No M 0689 )

Dadooing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (one cement, two sand) over 10mm base layer plastering and pointing with white cement neatly as directed etc., complete as per standard specification

Paving the floor with design Antiskid ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification.

Paving the floor with Vitrified Marbonite tiles of stain free nano polish approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on workion.

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete Item 35 Data

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers.etc., complete as per standard specification.

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as per standard specification.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Supply and fixing of Stainless steel (Salem stainless steel) Door frame ( Box section using stainless steel plate of 1.6mm thick) of size 100mm X 60mm with a rebate of 30 / 35mm X 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel holdfast etc. Item No 30

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 25GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the executive Engineer before use on work (PWD SOR Sl.No 65, P.70) M-0674

Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work (PWD SOR Page No 71, Item No M 0675)

Providing and laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 63 mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, Stone Dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Reinforced Cement concrete 1:1.5 :3 (one cement,one and half sand & three course aggregate)using 20mm ,gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete

PVC Pipe (Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance. (Schedule-40) 20 mm dia

25mm dia

Supplying and fixing in European Water Closet (white ) with 'P' or 'S' Trap with Double Flapped seat and seat cover with Brass Highes and 10 litre capacity PVC low level flusing tank with all internal fittings & accessories etc..

Supplying and fixing of position of Indian make white glazed earth were wash basin 550mm x 400mm with all accessories such as cost Iron brackets, 32mm dia C.P. Waste coupling, Rubber plug and chain, 32mm dia 'B' class, G.I. Waste pipe, 15mm dia, G.M.Wheel valve, 15mm dia Nylon connection, 15mm dia Brass Nipples, 15mm C.P. pillar tap etc.,

Supply and fixing in position of brass chromium plated screw down Tap 15 / 12mm Dia (Heavy Type) with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of chromium plated stop cock 15mm Dia with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of Porcelin soap dish of size 150mm x 150mm x 50mm with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of brass chromium plated towel rail 60cm long and 20mm dia with Brackets with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of PVC / Fibre Glass framed 5.5mm thick mirror, shelf type with Hard Board Backing with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of Stone ware gully trap of size 150mm x 100mm with cast Iron Double Gratings with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of Cast Iron Nahini / Floor Trap with stainless Steel Grating with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.

Supplying and laying the following dia un plasticized PVC pipes 6KSC & 10 KSC confirming to IS 4985/2000 and relevant specials including packing the joints with rubber /lubricant fixing ,holding wherever necessary and making good of the dismantled portion with necessary connections etc., complete as directed by engineer in charge. 75 mm dia

110 mm dia

Supply and fixing under ground sump and over head tank Cover with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers. Manhole Cover Size 900x900 mm double seal, air tight, non-slip SFRC cover & frame for manhole

Manhole Cover Size 60 cm x 60 cm(heavy duty) with frame - SFRC

Manhole Cover Size 1000 mm circle type double seal, air tight, non-slipFRP manhole cover with frame

Supply and fixing of Precast RCC(M30) Bio septic tank of 2.25KLD consists of three chambers - sedimentation chamber,Bioprocessing chambe with PP flower media(virgin plastics bio balls) & settling chamber which shall be coated inside and outside of tank with PU paint for extended life of tank up to 25 years. 2nos of manholes of 500mm shall be provided for easy and safety service. Bio-enzyme shall be used which consists of 20 different types of enzymes and bacteria which can develop in both aerobic and anaerobic conditions and this will start to reduce the BOD and COD of the sewage water and the water will loses its hardness during this process and neutralizes the PH between 6.6 to 7.5. The settled sludge shall be self-digestive. Treated water is orderless and colorless and shall be discharged to Garden/Choke pit/connected to existing sewer line. (Q)

Providing Geophysical survey incuding all and conveyance,etc., complete

Drilling of Borewell 150 mm dia in Sedimentary formation and hard rock area including labour charges for inserting of casing pipes and supplying and packing of pebbles etc., complete Up to 60m depth

From 60m to 90m depth

Supply and delivery of 150 mm dia PVC Plain casing pipe etc., complete.as per standard specification Upto 60 m depth ending below ground level

From 60m depth and up to 90m depth ending below ground level

Supply and delivery of unplasticised ribbed screen PVC casing pipe of the 200mm dia with screwed and socket end and centering guide for every 15m length of pipes as per IS / 12818 / 92 and as amended from time to time to suit the borewell upto 60m depth (C.M) Casing medium with ISI marking including, loading, unloading, freight, stacking and transit insurance charges etc, complete.

Supply and delivery of unplasticised ribbed screen PVC casing pipe of the 200mm dia with screwed and socket end and centering guide for every 15m length of pipes as per IS / 12818 / 92 and as amended from time to time to suit the borewell upto 60m depth (R.S) Ribbed Screen Pipe with ISI marking including, loading, unloading, freight, stacking and transit insurance charges etc, complete.

Supply and delivery of 200mm dia(8”) PVC end cap including cost and conveyance etc., complete

Labor charges for inserting the 150 mm P.V.C. casing pipes assembly with slots (or) without slots in the drilled holes including joining the pipes etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Municipal Engineer excluding cost of casing pipe etc., complete 200mm dia PVC casing pipe

Charges for developing the bore wells with Air Compressor 600cfm (Minimum 8 hours) including transportation labor and fuel charges for Compressor as directed by the Departmental Officer and conducting yield test by “V” notch method.

Supply and delivery of 125LpmX25m head submercible pump set of ISI make THREE PHASE SUBMERSIBLE PUMPSET SUITABLE FOR 100MM DIA BOREWELL AS PER IS 8034/2002 WITHOUT PANEL BOARD Supply and delivery of clear water vertical wet type submersible pump suitable for 100mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS 9283 /1995 and as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 % (350Lpm x 75 m head)

Supply and Delivery of 2.5 Sqmm PVC insulated and Sheathed 3 Core flat type copper cable confirming to IS 694/1990 Including all charges with excise duty and handling charges etc

Towards Labour Charges for the errection of Submersible pump set in bore well including fixing and jointing submersible cable with proper clamps up to the starter to riser pipes to the required depth valves erection clamps, pressure gauge up to the exterior of panel board consisting of TPICN switches starter ,Volt meter, Ammeter, three pilot (indicating) Lamps capacitor single Phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., Complete and testing the pump set and trail run for 10 days 10 HP

Supply and delivery of 50mm dia HDPE PIPES - PE 100 AS PER IS 4984/1995 PN 12.5 with excise duty including cost & conveyance of all materials to site and all labour charges etc., complete

Supply and delivery of 2of 4 sqno (56/0.3)pvc insulated sc with condition of 1100v on 7/20 GI Bend with service connection main SD.65., including cost & conveyance of all materials to site and all labour charges etc., complete

Supply of following GI pipes and PVC Special etc.,complete 32 mm dia GI hex nipple

32 mm GI pipe

32 mm dia GM NRV

32 mm dia GI union

12 mm dia nylon rope

Bore cover

32 mm dia kitty set

Bore stand

32 mm x 20 mm dia GI reducer

20 mm diax 0.20 m G I pipe nipple

20 mm dia GI coupling

32mm dia GI Coupling

1000 litre HDPE tank

32 mm dia PVC pipe (10Kg/sqm)

32 mm dia PVC tee

32 mm fuse carrier

32 A main Switch

32mm dia x 0.20 m G I pipe nipple

40mm dia PVC pipe

40mm dia PVC Coupler

40mm dia PVC Elbow

40mm dia PVC Tee

Supply, installation testing and commissioning of 3Ph EB Service panel & all necessary protection as per TNEB standard, including all fuse unit, EB meter shall be suitable for utilizing excess power from Solar panel, 40A DP MCB - 1 No, 32A DP MCB-2 Nos

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). SD 23

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and fixing of 3 phase 4 wire 4 way ICDB of 32 A per way with 100 A TPN MC switch with suitable trunking box Ms cable entry boxes and internal connection on suitable angle iron frame work with earth connection (SD. 175)

Supply and fixing of Horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure with 40 A 4 pole MCB isolater as incoming and 12 Nos. 6A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark (lik standard make) (SD. 179)

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m (SD.75)

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Supply and fixing of 300mm (12") sweep AC exhaust fan complete with necessary wall opening and making good of the wall. SD 115

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC power plug point.SD 40

Supplying and laying of PVC insulated, PVC sheathed, armoured, LTUG cable of size 2 core 10 sqmm Al.cable clamped on walls (SD 210)

Supplying and fixng of cable gland and termination with earth connection of size 2 core 10 sqmm etc, complete as per standard specification. (SD 182)

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129

Supply and fixing of 32 A TPN MC switch on incoming and 3 Nos 32 A DPMC Switch (Front Handle) as outgoing with suitable adoptor box with suitable MS cable entry box trunking boxes and internal connections on internal connections on suitable AI frame work with earth connection etc, complete.SD 172

Supply and fixing of 3 phase 4 wire 4 way ICDB of 16 A per way with 32 A TPN MC switch with suitable MS cable entry boxes trunking box and internal connections on suitable angle iron frame work with PWD earthing etc, complete.SD 173

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry . SD 233

Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG Cu wireand making good of the concealed portion with suitable colour (SD57)

Supplying and Laying of 3½ x 50 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 M putting 0.15 M layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [ SD 200]

Supplying of 4 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 M putting 0.15 M layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [SD 222 ]

Conveyance, installation, testing and commissioning of pre-wired 6 W LED Down light fitting suitable for Surface complete with all accessories etc.

Conveyance, installation, testing and commissioning of decorative type, 4mtr length, pre-wired hanging type 60 watts LED Tube Light complete with all accessories etc. directly on ceiling using 2 nos hanging rope of length 60 cm properly hooked to steel hooks anchored to the ceiling and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2Nos x 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 1Nos x 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supply and fixing Ton AC 2.00 Ton 5 Star Capacity with Copper Coil 5 Star rated M1985

Supply and fixing of 1200mm sweep Ac ceiling fan with stepped electronic 300W regulator with the existing down rod on the existing clamp (SD -112)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 1 Nos x 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supply, Erection of 8m Free Standing Single Arm Bracket 8 sided Octogonally continously tapered structured polewith base plate of size 300 x 300 x 12mm as per IS-875 with following specification. Bottom Pole Dia - 130mm Top Pole Dia - 70 mm Thickness of Pole - 3 mm The pole should be hot dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron. (PWDSOR-Page-150)

Coil earth to light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth (SD78)

Supply delivery and fixing of 48W LED Street Light Fitting with LED light. M1291

Supply and Fixing of CCTV Camera with Specification of Dahua- HAC-HFW 1100DP-B-0600 720P 1 Mega Pixel Analog High Definition camera, outdoor-25/30 fps@720P,1/2.9" 1 Megapixel CMOS, 50m IR,ICR, 6mm Lens optional, IR Bullet Dahua - Channel - AHD, High Video Quality on HD 1080N, Transmit Video Signal, audio signal & Dual way data communication signal over one coaxial cable, HD Video transmission without Video quality loss & delay, extremely, long transmission distance (300), as directed by Departmental Executive Engineer. Supply and Installing sony CC TV camera SD

POE Switch for CCTV IP Camara 24 Port

29" Led TV for display LMR

Hard Diisk for NVR (8TB )

Network Video Recorder for CCTV 16 Channel - 2SATA 2mm Hard Disk

Rack With Accesssories -4 Urack

Rack With Accesssories -12 Urack

Armoured LAN & CCTV Cable CAT -6

R.C.C.Jolly by a new of following size in R.C.C. 1:1.5:3 using 20mm gauge hard broken granite stone jelly and river sand excluding cost of reinforcement but includingcharges,fabrication charges curing neat finishing and labour charges for fixing the jolly in position with standard spefication

Brick work for seating - Construct 115mm thick brick wall of with standard wire cut bricks and use CM 1:3 (one cement & Six sand), size of 9"x 4 3/8 " 2 3/4" including finishing, curing, etc., complete and fill with approved coarse rubbles for filling.

Brick work for seating - Construct 230mm thick circular brick wall of with standard wire cut bricks and use CM 1:5 (one cement & Six sand), size of 9"x 4 3/8 " 2 3/4" including finishing, curing, etc., complete and fill with approved coarse rubbles for filling.

Counter top - Providing and fixing of 2 inch thick natural stone Kadappa equivalent to the prescribed size and shape with cement Grout 1:6 as instrcuted by site engineer

Seating area - Providing and fixing of 1 inch thick natural stone Kadappa equivalent to the prescribed size and shape with cement Grout 1:6 as instrcuted by site engineer

Supply and delivery of HIGH BACK CHAIR with Executive ergonomic mesh chair with headrest in Black, 700mmAluminum base, Adjustable lumbar for excellent back support, Height adjustable back with 5 separate positions, Adjustable tension control, Dual pivot mechanism, Multi-functional 3D adjustable arms, Full diamond mesh, Extralarge executive headrest, Heavy duty SHS gas lift, Waterfall seat, Maximum Weight limit - 150kg, Suitable for 2

Supply and delivery of OFFICE CHAIR with Deluxe Mesh chair with folding Arms, Breathable Mesh Back, Air Flow Mesh Seat, Tilt Mechanism lockable in the upright position, Folding Arms, Heavy duty gas lift (110 kilos), Foam and Fabric conform to BS5852 UK FR, W690 x D755 x H960 - 1060mm etc., complete

Supply and delivery of STUDY CHAIR / CLASS ROOM CHAIR with Seat Material –Fabric, Back Type - Mid Back Arm Type – Fixed, Arm Warranty - 1 Year, Brand - MBM Seating Height - 20 - 21 Inches, Color – Black, Height Adjustable – Yes, Seat Height Adjustable – Yes etc.,

Supply and delivery of COMPUTER CHAIR with Low back chair with arms and plastic outer cover, Primary Material – Castors, Chair base, Gas lifter, chair arm, Press wood sheet, Plastic outer cover, Style – Modern

Supply and delivery of CHILDEREN’S CHAIR with Lightweight and easy to move, About $15 in materials to build each chair, Easy to build plan designed for a novice woodworker, Uses basic tools, Classic style can is beautiful painted or stained, Storage compartment is big enough for notebooks and more, Works with standard children's tables, Measurement - 0.42m

Supply and delivery of CLASS ROOM CHAIR with Seat Material –Fabric, Back Type - Mid Back Arm Type – Fixed, Arm Warranty - 1 Year, Brand - MBM Seating Height - 20 - 21 Inches, Color – Black, Height Adjustable – Yes, Seat Height Adjustable – Yes etc

Supplying and fixing of Conference Hall - Half Round Table to site, by using of MDF (Medium Density Fiber) panel sheets for 15 nos of seating capacity, the cost including of material charges, required hinges at bottom support, nails, screws for joints and finish the top with Mica sheet, also including making and labour charges complete. (Total length(straight table) = 4.85m,Curve portion table length = 2.45m,Straight portion Table width = 0.70m,Curveature portion Table width = 0.90m) Note : Reading table may also be provided as study table on theatre type having 8 to 10 seats on either side of the table in rows to accommodate 30 seats for

Supplying and fixing of System table with Key Board Rack to site, by using of MDF (Medium Density Fiber) panel sheets, the cost including of material charges, making charges ,Required hinges at bottom support, nails, screws for joints and labour complete. At computer Zone area tables based on number of computers.(Measurements for Computer tables, For each system cabin Length =0.90m,Width = 0.60m,Height of table top from ground = 0.76m,Cabin

Supplying and fixing of Study Table with Cabin to site, Each cabin length = 0.90m,width = 0.60m, Height of table top from ground = 0.77m ,Cabin partition height from table top = 0.43m the cost including of all material charges, making charges, Required hinges at bottom support, nails, screws for joints and labour etc., complete

Supplying and fixing of Reception table with Fittings to site, by using of MDF (Medium Density Fiber) panel sheets, the table with the size of 2.20m x 0.60m and Height = 0.90m with Required trays and draws and Computer spaces as per site conditions. The cost including of material charges,

Supplying and fixing of Librarian table with Fittings to site, by using of MDF (Medium Density Fiber) panel sheets, the table with the size of 2.20m x 0.60m and Height = 0.90m with Required trays and draws and Computer spaces as per site conditions. The cost including of material charges, making charges and labour etc., complete

Supplying and fixing of Manager Room Table to site, by using of MDF (Medium Density Fiber) panel sheets system fittings and keyboard section with the over all table size of 2.20m x 1.10m with Height = 0.77m to site with required trays and Draws at both sides, the cost including of material charges

Supplying and fixing of Paper Display to site, By using of MDF (Medium Density Fiber) panel sheets the display furniture table size of 2.50 x 0.45m and Height = 1.23m with Magazine Bay opening Each = 0.25m at both sides ,the cost including of material charges, making charges and labour etc.,

Supplying and fixing of Book racks at Ramp side : (4.16m x 2.56m =9.81Sqm) to site, By using of MDF (Medium Density Fiber) panel sheets the cost including of material charges,

Supplying and fixing of Book racks at Ramp side of size 3.86m x 1.67m = 6.44 Sq.m, by using of MDF (Medium Density Fiber) panel sheets the cost including of material charges, making charges and labour etc., complete.

Supplying and fixing of Book self size 2.45m x 2.22m X 2.22m, by using of MDF (Medium Density Fiber) panel sheets the cost including of material charges, making charges and labour etc., complete.

Supplying and fixing of Children's Table to site for in bottom of OTS area, By using of MDF (Medium Density Fiber) panel sheet and also the table top should be finished with mica sheet of variant colour as per the instruction of Departmental officers, the over all table size of 1.00m x 1.00m to site With Height = 0.55m with seating capacity of 5nos (per each table) the cost including of material charges, making charges and labour etc

Supply, Delivery & Installation of Desktop (without display) with the following specification including cost of materials and labour charges for installing etc., Technical Specification : Processor - Intel Core i3 Processor (10th Generation Processor & Board) Ram & Storage - 4GB RAM/1TB SATA HDD with DVD Writer, Key Board & Mouse OS – Windows 10 SL

Providing and placing of native trees which grows to an height of 4mtrs planted with rich manure and graded soil mixture dug upto a depth of 1.5mtrs as approved by the site engineer

Providing and placing of native plants which grows to an height of 2.5mtrs with flowering nature (bright coloured) planted with rich manure and graded soil mixture dug upto a depth of 1.0m as approved by the site engineer

Providing and planting of heliconia plant along with tropical leafy plants in the planter boxes provided at ground level not less than 10 plants per metre

Supply errection and commisioning of 40KV Genset of diesel capacity 50liter and automatic type of ISI Make including cost of concrete bed , errection and all other cost and conveyance etc complete

Providing rain water harvesting using 3 nos.of RCC well rings of 90cm inner dia (clear) with 5cm wall thickness made out of cement concrete 1:2:4 using 20mm hard broken jelly to a height of 30cm each supplying and fabricating 16 nos. of 6mm dia MS rod vertically and 3 nos. of 6mm dia MS rod circumferentially tied together with 18 guage binding wire for well rings including necessary earth work excavation 1m dia to a depth of 1m, supplying and filling 40mm HBG inside the erected well ring to a depth of 90cm, and top covered with RCC circular perforated cover slab of 1m dia and 5cm thick which inclusive of cost and fabrication of 6mm M.S reinforcement at 15 cm spacings on both directions and one 6mm M.S rod ties at the edge of the slab circumferentially including cost of moulding, curing, finishing and well placing in position and disposing off excavated earth with all initial leads and lifts in places as shown by the Departmneal officers etc., complete in all respects.

Supply anrrection of Fire Shield brand' Stored Pressure Fire Extinguisher ISI Marked, Powder type Fire 6 Kg. Capacity

Goods and Service Tax @ 18%

SESHADIRI.T