SPL REPAIR TO BLDG NO P-77 (CENTRE MI ROOM) AND PROVN OF 04X SOLAR CUM ELECTRIC GEYSER AT 39 GTC IN VARANASI CANTT UNDER GE (EAST) ALLAHABAD

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Material & Labour for 75 mm thick PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in plinth protection including making 12 mm wide joint to the full depth of PCC at the length not exceeding 3.0 mtr and at every change of direction and filling the same with and including bitumen and sand 1:3 by weight complete all as specified & directed.

Material & Labour 40 mm thick PCC 1:2:4 type B-1 using 20mm crushed stone aggregate as in floor finish or base of floor, surface finished even with using extra cement complete all as specified & directed.

Material & Labour for 25 to 30 mm thick paving tiles of size 300mmx300mm with wear resisiting coat of approved design laid with cement slurry @ 3 kg/ sqm over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified & directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete and removing rubbish off from the premises complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L light shade vitrified coloured tiles 10 mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L light shade vitrified coloured tiles 10 mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm in vertical surface such as skirting, dados, risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L glazed ceramic coloured tiles 450mm X 350 mm x 7mm / 350mm X 250 mm x 7mm thick in vertical surface such as skirting, dados, risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortar including all quions arches dressed stone work etc and excluding ashlar facing dressed stone work etc. complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removing of all rubbish off from the site complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L 5 mm thick rendering in cement mortar 1:3 on concrete surfaces in ceiling, finished fair & even complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

Material & Labour for preparation the base of new plastered surface of walls by applying two coats of oil bound distemper [Acrylic] over and including 2 mm thick Birla or JK wall care putty over a coat of primer complete all as specified & directed.

Complete removal of existing treatment of walls with steel scrapper or steel wire brushes, cleaning the plastered surfaces including filling depressions of scrapped surfaces and preparation of the plastered surfaces and applying two coats of oil bound distemper [Acrylic] over and including 2 mm thick Birla or JK wall care putty over a coat of primer complete all as specified & directed.

Material & Labour for preparation of new plastered surface of walls with sand or emery paper and apply two coats of cement base paint complete all as specified & directed.

Complete removal of existing treatment of walls with steel scrapper or steel wire brushes, cleaning the plastered surfaces including filling depressions of scrapped surfaces and preparation of the plastered surfaces and applying two coats of cement base paint complete all as specified & directed.

Material & Labour for preparation of new plastered surface of ceilings and applying three coats of white wash complete all as specified & directed.

M&L for preparation of old decorated plastered surfaces of celling including cornices,pilastered etc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying two coats of white wash complete all as specified and directed.

Material & Labour for preparation of old plastered surface of walls and applying two coats of exterior acrylic emulsion polymer base paint complete all as specified & directed.

Supply & Fixing in repair 15 mm bore galvanised steel water tubing medium grade for water supply pipes & connections with all fittings such as sockets, elbows, unions, Tees & short length etc and fixed to walls with steel hooks or laid in floors in any length complete as specified & directed.

Supply & Fixing in repair 20 mm bore galvanised steel water tubing medium grade for water supply pipes & connections with all fittings such as sockets, elbows, unions, Tees & short length etc and fixed to walls with steel hooks or laid in floors in any length complete as specified & directed.

S&F in repair gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete all as specified and directed.

S&F in repair rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms) complete all as specified and directed.

S&F in repair rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms) complete all as specified and directed.

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe 600mm long, fixed in repair complete all as specified and directed.

S&F in repairs vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with plastic water closet seat cover white closet pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed. NOTE: Plastic sheet cover shall be measured and paid sapertely as "supply only" under respective item of BoQ.

S & F in repair vitreous China wash hand basin white flat back of size 550 mmx400mm fixed on and fixing of cantilever brackets of mild steel angle 35 mm x 35 mm x 5 mm, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe (rigid quality) including fixing of tap etc. complete all as specified and directed. Note :- Pillar tap shall be measured & paid seperately as supply only under respective item of BoQ".

Supply only pillar tap cast copper alloy with capstin heads chromimium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe 15 mm bore complete all as specified and directed.

S&F in repair chromium plated soap dish complete all as specified and directed.

S&F brass chromium plated shower rose 65mm to 90 mm size with swivel joints, fixed in repairs complete all as specified and directed.

S&F in repair tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete all as specified and directed.

S& F in repair PVC connections 15 mm, 450 mm length with brass nuts at both ends complete all as specified and directed

S&F in repair bib taps cast copper alloy chromium plated with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule 15 mm bore complete all as specified and directed.

Material & Labour for preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified & directed.

Material & Labour for reinforced cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in chajjas or kitchen shelves, cantilever or supported on walls or similar works complete as specified & directed.

S&F TMT mild steel 8 mm dia over cut to length bent to shape required including cranking bending spirally for hooking for columns hooking and binding with including mild steel annealed wire not less than 0.9 mm dia securing with clips complete all as specified and directed.

S & F in repair for 15 mm bore angle valve cast screwed down, high pressure, with crutch or butter fly handle, for iron pipe or for unions complete all as specified and directed. MAKE :- L&K cat No. 0047 or equivalent in specified makes as approved

S&F in repair stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified and directed.

S &F in repairs grating round 125 mm size with waste hole of PTMT (minimum weight 100 gms) complete all as specified and directed.

S & F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with chromium plated bracket guard and railing 60 cm complete all as specified and directed.

S&F in repair mild steel tubing of 25 mm dia with PVC coating for curtain rod fancy type including fancy type PVC rings decorative holder and CP brass brackets (wall to wall or flush to wall) for securing to curtain rod, complete all as specified and directed.

Dismantling of AC corrugated or semi corrugated sheet including AC ridges as in roof covering complete all as specified & directed.

Supply & Fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick, coloured having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws at every alternate corrugation complete all as specified & directed.

Taking down chowkats of frmes exceeding 1.50 sqm but not exceeding 4.0 sqm each with shutter (without taking off shutters from the frames) each including removing from site complete all as specified and directed.

Taking down chowkats of frmes exceeding 1.50 sqm each with shutter without taking off shutters from the frames) each including removing from site complete all as specified and directed.

S&F 35mm thick 2nd class hardwood rail and style plain framed, panelled shutter (two panel) factory made with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F factory made second class hardwood glazed and skeleton shutters 30 mm thick, open rebated and prepared to receive glass, gauze, etc. (with sash bars), divided into square with plain chamfered or rounded ,metred edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. are provided with stiles and rails as specified in SSR Part-I, section 8 clause 8.24 (a) complete all as specifed and directed.

Supply & Fixing in repair powder coated aluminium door frame with shutter having with door frame of hollow section 63.5x38.1x1.5 mm thick & shutter with bottom & middle rail of section 114.3x44.45x1.5 mm thick and styles & top rail of section 85x44.45x1.5 mm thick with central locking arrangement with & including mortice handle lock of make of Godrej or Link having seven lever and self closing device [Floor door spring by cutting of floor of Sandhu make] with rebate including jointing cleats, fixing builder hardware fittings and glazing with 5.5 mm thick ordinary plain glass including aluminium snap beading & rubber packing and necessary fittings, fixtures complete all as specified & directed.

Supply & Fixing in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S & F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails. mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F rolled mild steel sections conforming to Fe-410-W (Gde-E-250 quality-A) as in framing for cooler stand, cladding, glazing and the like including door frames/ chowkats, fixed with angle cleats and connecting plates, etc including necessary welding and reviting as moulded in desired shape complete all as specified and directed.

Material & Labour for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in fixing of hold fasts including necessary form work complete all as specified & directed.

S&F in repair 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F in repair 300mm size stain less steel sliding door bolts, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

Supply & Fixing 100mm long mild steel butt hinges medium weight cold rolled with steel pin hinge and fixed with steel screws complete all as specified & directed.

S&F in repair 150 mm size aluminium anodised handles, cast type complete all as specified and directed.

Material & Labour for preperation of new wood or wooden based surface with sand or emery paper of any description over 10 CM width or girth applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified & directed.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, with glazing bars dovetailed or welded including two coat of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces complete all as specified and directed.

S&F in repair factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, without glazing bars dovetailed or welded including two coat of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces, fixed in repair complete all as specified and directed.

S & F in repair factory made steel ventilators with top hung shutter including hinges, steel peg stay including two coats of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces complete all as specified and directed.

S&F in repair galvanized steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with galvanized steel wire steples complete all as specified and directed.

Material & labour for mild steel framed work such as grills, gratings with ends of bars shouldered and or riveted, or forged into spikes; framed guard bars, railings, hold fasts or similar work complete all as specified & directed.

S&F in repair Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) suitable for 100 mm bore pipe complete all as specified and directed.

Supplying, laying, jointing and testing reinforced concrete pipe 200 mm internal dia NP-3 laid in trenches and jointed with collars in cement sand mortar 1:1 complete all as specified & directed.

Material & Labour for concrete bed to drain pipes of 200 bore including packing under and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate complete all as specified & directed.

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trnches or in floors, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

M&L for providing water proofing treatment over cleaned roof surface with APP modified bitumenous membrane weight not less than 3kg/sqm comprising of following and testing after completion including taking down of old water proofing treatment from roof/ concrete surfaces and removal to a distance exceeding 250 mtr. :- (a) 10 mm thick plaster/ screed bed in cement mortar 1:4 complete mixed with water proofing compound @ 3% as per manufacturers instructions complete all as specified and directed. Note:Water proofing compound measured and paid seprerately under respective of "BoQ". (b) Cleaning roof surface by wire brush, brooming & removing dust & shall be painted with a coat of bituminous primer conforming to IS:3384-1986 @ 0.3 litre per Sqm uniformity complete all as specified and directed. (c) After primer,the entire roof surface applying tack coat of hot blown bitumen grade 85/25 grade conforming to IS 702-1988 @ 1.2 Kg per Sqm pver primer. (d) Over hot bitumen ,laying APP modified polymeric water proofing membrane consisting of 3mm thick weight not less than 3 Kg per Sqm over entire area laid with 100 mm side lap and end lap on prepared surfaces as of manufacture"s technical instruction & sealed complete all as specified & directed. (e) Again the entire roof surface applying tack coat of hot blown bitumen grade 85/25 grade conforming to IS 702 @ 1.2 Kg per Sqm. (f) Tapping with PCC tiles 300x300x20 mm thick laid over 20mm thick of CM 1:4 screed bedding and filling tiles joint with CM 1:3 complete all as specified and directed.

Supply only integral water proofing compound complete all as specified & directed.

Taking down carefully aluminium/ copper point wiring any type (light, fan, socket or power) complete including all fittings such as switches, sockets, ceiling rose, pendants, holders, regulators etc. and making good disturbed surface of walls/ floor complete all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FR type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring including concealed pressed steel terminal box of required size not less than 1.6 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 3.0 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FR type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed for the followings:-

Ditto all as item No. 79 here-in-before but for one light or fan point controlled by one, one way switches complete all as specified and directed.

Ditto -all as item No. 79 here-in before but 3pin ,5amp socket out let on the same board with other switch complete all as specified and directed.

Ditto- all as item No. 79 here-in-before but one 3 pin, 5amp socket out let on independent board complete all as specified and directed.

Ditto all as item No. 79 here-in-before but 3 pin , 15 Amps switch socket combination on independent board with 4 Sq mm cable multistranded copper conductor complete all as specified and directed.

Material & Labour for Sub main wiring with two single core PVC Insulated cable two run of size 6 Sqmm multi-stranded copper conductor FRLS cables drawing into and including PVC conduit, medium grade not less than 20/25 mm dia with all conduit accessories and one run of 6 Sqmm multi-strand copper conductor FRLS cable as continuous earth wire complete all as specified and directed. Note : - Two run of 6 Sqmm & one run of 6 Sqmm cable shall be measured as one unit run.

S & F for switch piano, flush type, 5 amps, single pole , one way , 230 volt complete all as specified and directed.

S & F for 2/3 pin, 5 Amp/ 6 Amp , socket outlet, flush type, 2 in 1 complete all as specified and directed.

Supply & Fixing Switch socket combination 2 in 1, 3 pin / 5 Amp and 15 Amps flush type of polycabonate body complete all as specified & directed.

S&F ceiling rose single phase , PVC poly carbonate , insulated body three terminals ISI marked complete all as specified and directed.

Supply & Fixing lamp holder insulated body with back plate suitable for batten fittings complete all as specified & directed.

S&F stepped type electronic fan regulator flush type 230 V, 120 watt, AC single phase complete all as specified and directed.

S& F for sheet metal enclousre for MCB DB's TPN, 4 way, double door, 415 Volts with 200 Amp rated bus bars including taking down existing unserviceable MCB DB complete all as specified and directed.

S& F for sheet metal enclousre for MCB DB's SPN, 8 way, double door, 240 Volts with 200 Amp rated bus bars including taking down existing unserviceable MCB DB complete all as specified and directed.

S& F for sheet metal enclousre for MCB DB's SPN, 2 way, double door, 240 Volts without bus bars including taking down existing unserviceable MCB DB complete all as specified and directed.

Supply & Fixing MCB Single Pole 240Volt, 6 to 32Amps,10KA breaking capacity "C" curve ISI marked complete all as specified & directed.

Supply & Fixing MCB Single Pole and Neutral 240Volt, 40 to 63 Amps,10KA breaking capacity "C" curve ISI marked complete all as specified & directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below normal ground level) connected to galavanised earth lead wire 4.0 mm dia (7.5m) as means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe (ISImark) light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing and taking down of old ineffective earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth wire and protection pipe upto 7.5 meter beyond the earth plates electrode and the earth resistance of the whole system shall be as near as possible to 0 but shall not in any case exceed Five ohm.)

Supply & Fixing 2x20 watt LED ceiling mounting polycarbonate body [Unbreakable] decorative type light fittings including cool white LED retrofit tube rod with extruded aluminium body heat shrink, envoirement friendly, energy efficient prewired and making necessary electric connection from ceiling rose with 23/.0076 flexible three core copper wire 1.0 RM long & fixed to wall firmly complete all as specified & directed by Engineer-in-Charge. Make : Philips / Wipro/ Bajaj as approved by GE.

Supply & Fixing 1x20 watt LED ceiling mounting polycarbonate body [Unbreakable] decorative type light fittings including cool white LED retrofit tube rod with extruded aluminium body heat shrink, envoirement friendly, energy efficient prewired and making necessary electric connection from ceiling rose with 23/.0076 flexible three core copper wire 1.0 RM long & fixed to wall firmly complete all as specified & directed by Engineer-in-Charge. Make : Philips / Wipro/ Bajaj as approved by GE.

Supply & Fixing single pole and neutral sheet metal enclosure and two pin and earth plug and socket plug top complete with & including one number MCB SP 25 Amps complete all as specified & directed.

Material & Labour for Sub main wiring with two single core PVC Insulated cable two run of size 2.5 Sqmm multi-stranded copper conductor FRLS cables drawing into and including PVC conduit, medium grade not less than 20/25 mm dia with all conduit accessories and one run of 2.5 Sqmm multi-strand copper conductor FRLS cable as continuous earth wire complete all as specified and directed. Note : - Two run of 2.5 Sqmm & one run of 2.5 Sqmm cable shall be measured as one unit run.

Material & Labour for Sub main wiring with two single core PVC Insulated cable two run of size 4.0 Sqmm multi-stranded copper conductor FRLS cables drawing into and including PVC conduit, medium grade not less than 20/25 mm dia with all conduit accessories and one run of 4.0 Sqmm multi-strand copper conductor FRLS cable as continuous earth wire complete all as specified and directed. Note : - Two run of 4.0 Sqmm & one run of 4.0 Sqmm cable shall be measured as one unit run.

Supplying, laying, jointing, commissioning & testing of XLPE cable cross sectional area 50 Sqmm 3 ½ core Insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down old existing damaged burnt cable and removed from site complete all as specified & directed. Make : Havells / Plaza / KEI / Gloster / Finolex / Grandlay Cables

Supplying, laying, jointing, commissioning & testing of XLPE cable cross sectional area 10 Sqmm 2 core Insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down old existing damaged burnt cable and removed from site complete all as specified & directed. Make : Havells / Plaza / KEI / Gloster / Finolex / Grandlay Cables

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft / loose soil including bottom surface to required level or slope for laying of cable complete all as specified & directed.

Returning filling in excavated soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm depth in soft / loose soil complete all as specified & directed.

Removing excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed.

Material & Labour for sand cushioning with clean dry local sand [unwashed] for protection of under ground cable (8 cm before laying and 15 cm after laying of the cable) in trenches and consolidated complete all as specified & directed. Note : Punned thickness 18 cm only shall be considered for payment.

Material & Labour for sub class ‘B’ common burnt bricks old size, laid dry, flat with width equal to length of bricks as cover / laid over the cable to protection of under ground cable complete all as specified & directed.

Supply & Fixing 50 mm bore galvanised iron water tubing "light grade" ISI marked including fittings such as bends, tees, sockets etc fixed on walls / pole or laid in trenches under road crossing including taking down old existing pipe complete all as specified & directed. Note : Excavation, earth work, sand cushioning & protection work shall be measured & paid separately.

Material & Labour for drilling holes under road [suitable up to 80 mm bore pipe] with trenchless technology with-out damaging existing road / path / hard standing to cross / pass the LT UG cable incluidng necessary T&P required complete all as specified & directed.

Supply & Fixing Low density poly athelene pipes (LDPE) of pressure rating 6kg/cm² laid in trenches / floor of size 50 mm dia for protection of cable including cutting chases in floor complete all as specified & directed.

Supply & Fixing Building security / street LED light fitting 45 watt IP-65 protection energy efficient and making electrical connection with 2.5 Sqmm twin core copper wire 1.5 long complete fixed with 40 mm dia MS pipe medium grade bracket [1.2 m long & bent to required shape] and fixed with flat iron 40x6 mm clamp two nos with nut bolts & washers as required fixed to pole or walls complete all as specified & directed. Make : Philips / Havells / Bajaj as approved by GE.

Supply & Fixing Post top gate light 45 Watt aluminium die cast body with toughened acrylic glass suitable for fixing on 40 mm dia pipe including making necessary electric connection complete all as specified & directed. Make : Philips / Havells / Bajaj as approved by GE.

Supply & Fixing LED retrofit lamp ball type 15 watt, B-22 holder base with co extruded polycarbonate body and aluminium heat shrink warm white including taking old light fittings complete all as specified & directed by Engineer-in-Charge. Make : Havells LHLDEREEMD8X015 or equivalent make in Philips / Wipro or Bajaj as approved by GE.

Supplying, Installation and testing of Energy Efficient five star rating in replacement Electric Water Heater storage tank of capacity 25 ltr 2 KW (Geyser) with MS stand of standard size, inlet outlet, overflow water pipe and electric connections complete with nuts and bolts of suitable size and making good disturbed surface of wall to match the existing complete as specified & directed. Make : Havells(Puro Plus 5S) or equivalent make as approved by GE.

Supplying, Installation and testing of Hi wall split AC units indoor/ outdoor complete with cordless remote control unit and with inbuilt heating and cooling arrangement and digital inverter twin rotary of 2.0 Ton Capacity including taking down old unserviceable AC any type complete as specified & directed. Make : Daikin / Carrier / Hitachi Note :- Old unserviceable ACs retrieved from site shall be transported and deposited in MES store yard by by the Contractor.

S&F heat resistant PVC flexible connection pipe 450 mm long suitable for 15mm dia pipe with brass creamed nipple and nuts heavy duty pressure grade 6 kg/ cm² and temp upto 90 degree centigrade complete all as specified & directed.

Supply & Fixing 300 mm sweep exhaust fan with louvers high speed copper wound motor suitable for 230 volt AC supply heavy duty complete with steel body and making necessary electric connection with ceiling rose with copper wire of suitable size complete all as specified & directed.

Taking down existing ceiling fan for servicing, greasing, replacement of bearing, safety pin, canopy, fan condensor, clamp, rubber reel, nut/bolts as required at site and cleaning, preparing surfaces and filling cavities with filler including painting with one finishing coat of synthetic enamel paint white in colour and re-fixing in its original position including making all electric connection complete all as specified & directed.

Supplying and fixing in repair air circulation wall mounting fan PVC body of 350 mm sweep with inbuilt speed regulator single phase 240V complete all as specified & directed. Make:- Havells/ Crompton/ Bajaj

Supplying, Installation, Testing and Commissioning of 'Solar Hot Water System' (Flat Plate Collector) based on indirect transfer of heat of capacity 100 LPD complete all as specified & directed.

S&F double pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB complete all as specified & directed.

S&F Hot water pipe duly insulated with glass wool and aluminium cladding 25 mm bore laid on roof/floor or fixed to wall complete all as specified & directed.

S&F Hot water pipe duly insulated with glass wool and aluminium cladding 15 mm bore laid on roof/floor or fixed to wall complete all as specified & directed.

S&F 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brassferrule and fixed complete all as specified & directed.

S&F 25mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified & directed.

S&F 15mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified & directed.

S&F Connection Nipple suitable for HDPE water tank. (Minimum weight 20mm- 45gms ) for inlet connection complete all as specified & directed.

S&F connection Nipple suitable for HDPE water tank. (Minimum weight 25mm- 65gms) for outlet connection complete all as specified & directed.

M&L for fabrication, welding and screwing at site framework of water tanks and similar work conforming to Fe.290.Gde-E-165 mild steel angle Iron stand for cold/hot water tank with required size Angle iron including painting with two coat of synthetic enammled paint over two coat of red oxide primer complete all as specified & directed.

S&F heavy duty PVC float valve suitable for 20mm dia bore complete all as specified & directed. Make Prayag or equivalent

S&F Bib tap suitable for 15mm dia bore pipe standard of PTMT fancy type chromium plated high pressure screwed for iron pipe and fixed complete all as specified & directed.( Minimum weight 15mm-105gms

HARI OM CONSTRUCTION

M/S Rajeev Kumar