SPECIAL REPAIRS TO TOILET BLOCK GF FOR SM BARRACK OF BDE HQ CAMP AT MIL STN JALIPA UNDER GE ARMY BARMER

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removing rubbish to out side MD land complete all as specified and as directed.

M&L 15 mm thick, plastering in CM 1:4 on stone masonry surfaces ( external wall surfces) finished fair and even with out using extra cement including mixing with water proofing compound ( WPC) as per manufacturer instructions complete all as specified and as directed. Note :- WPC will be measured and paid separately as supply only.

M&L 15 mm thick, plastering in CM1:6 on stone masonry surfaces ( internal wall surfces) finished even and smooth with out using extra cement complete all as specified and as directed.

M&L plastering 5 mm thick in CM 1:3 on stone/ concrete surfaces of ceiling , finished even and smooth without using extra cement complete all as specified and as directed.

Preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

Preparing new plastered or unplastered surfaces and applying with wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and as directed.

Taking down chowkats or frames (without taking off shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and as directed .

Taking down chowkats or frames (without taking off shutters from the frames) area not exceeding 1.5 Sqm each complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specifications complete all as directed .

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and as directed.

Refixing the chowkats or frames (without taking off shutters from the frames) area not exceeding 1.5 Sqm each in the same opening after easing and adjusting complete all as specified and as directed.

S&F Factory made steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel complete all as specified and as directed.

Hacking out old broken glass [any thickness, size, quality or description] from metal frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed.

S&F sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Preparation of new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed .

Preparation of old painted wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed .

S&F 150mm size aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 100mm size butt hinges extruded aluminium alloy, with mild steel hinge pin, anodised type B-21 complete all as specified and as directed.

S&F 150 mm size aluminium anodised handles, caste type, complete all as specified and as directed.

M&L precast cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate as in solid block masonry exceeding 10cm width and setting in cement mortar 1:6 including demolition existing masonary complete all as specified and as directed .

Demolition of stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

M&L squared rubble walling, Jodhpur type, brought to coursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

M&L squared rubble walling, Jodhpur type, brought to coursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 except stone complete all as specified and as directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

M&L TMT steel bars of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M&L reinforced cement concrete type B-1 [Nominal Mix] 1:2:4 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L granite slab 18 to 20mm thick machine cut, factory polished, Jet Black colour, as in steps, jambs, pillars, window cills, cooking platform, and like bedded and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the shade of granite stone over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or credited to contractor complete all as specified and as directed.

Taking up or down 25mm bore steel tubing and connections including cleaning for refixing or credited to contractor complete all as specified and as directed.

M&L GI tubing (ISI marked) 15mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floorscomplete all as specified and as directed.

M&L GI tubing (ISI marked) 25mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floorscomplete all as specified and as directed.

Re fixing / Re laying old 15mm bore GI tubing and connections in new or old position including provision of new GI fittings ( as ordered) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed .

Re fixing / Re laying old 25mm bore GI tubing and connections in new or old position including provision of new GI fittings ( as ordered) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed .

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) of any dia set in cement mortar complete all as specified and as directed.

S&F110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F110 mm bore (SWR) PVC bends any radius complete all as specified and as directed.

S& F 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F 75 mm bore (SWR) PVC bends any radius complete all as specified and as directed.

S& F 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S & F 75mm bore PVC [SWR] floor trap with grating including jointing with solvent cement complete all as specified and as directed.

S&F brass chromium plated tubular towel rail, 20mm dia, D Type, 600 mm long between flanges including brackets complete all as specified and as directed.

S&F in repairs vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar [1:2], securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, 32mm bore PVC flexible waste pipe, grating and union for discharge pipe, CP screws etc complete all as specified and as directed.

S&F 500 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including ball valves for 15mm bore pipe, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (minimum weight 142 gms) and taking down old tank complete all as specified and as directed.

S & F in repairs vitreous china ware wash hand basin, white, flat back of size 550 mm X 450 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe,PVC connection15mm size with PTMT nuts of length 450mm long including pillar tap, cast copper alloy, chromium plated, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S&Fin repairs vitreous china wash down water closet pan [Pedestal pattern], white [excluding flushing cistern and flush pipe] including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.

S & F in repairs white vitreous china squatting pan "Orissa pattern" of size 580 mm X 440 mm with integral foot rests andPVC 'P' or 'S' trap including provision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed.

S&F in repairs 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed.

S&F in repairs stop valves, 15 mm dia, cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc complete all as specified and as directed.

S&Fin repair, fancy type, chromium plated, bib tap, long body cast copper alloy with spindle,half turn with screwed down, screwed for 15 mm bore iron pipe complete all as specified and as directed.

S&F in repair CP, fancy type, stop valves / angle cock, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for unions complete all as specified and as directed.

S & F in repairs, brass chromium plated shower rose of size 125mm with or with out swivel joints fixing to steel pipes complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) including removal of debris to out side MD land complete all as specified and directed.

M&L PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate , 25mm thick in sub base of flooring complete all as specified and as directed.

Demolition of wall tiling of any description including cement mortar bedding / backing coat and removing rubbish to out side MD Land complete all as specified and as directed.

M&L Glazed coloured ceramic tiles of size 450mmx350mmx7mm/ 450mm x 300mm x 7mm thick on vertical surface such as dado/ skirting etc., over and including 10mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white cement / coloured cement to match the tiles complete all as specified and as directed.

M&L non skid ceramic tiles, coloured, of size exceeding 0.06 Sq.m and not exceeding 0.11 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 complete all as specified and as directed.

M&L for machine cut kota stone slab 20 to 25mm thick in floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over and including 20mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for machine cut kota stone slab 18 to 20mm thick in riser of steps, skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10 mm thick backing coat in CM 1:4 complete all as specified and as directed.

Preparation of surfaces of roof slab by brushing with wire brushes to remove loose / dirt materials and sweeping with brooms or gunny bags or mechanical device etc., and applying neat cement slurry with 3.0 KG of cement per Sq.m area with mixing of liquid water proofing compound as per manufacturer instructions complete all as specified and as directed. Note :- WPC will be measured and paid separately as supply only.

M&L plain cement concrete, 1:2:4 type B0 using 12.5mm graded stone aggreage, 40mm thick with mixing liquid water proofing compound as per manufacturer instructions, as in levelling courses of roof / chajja / kerbs,rounded or chamfered on edges including necessary form work complete all as specified and directed. Note :- WPC will be measured and paid separately as supply only.

M&L screed bed 10 mm thick in CM 1:3 on roof for laying of water proofing treatment mixing with water proofing compound as per manufacturer instructions complete all as specified and directed. Note :- WPC will be measured and paid separately as supply only.

M&L APP based polymeric membrane minimum weighing not less than 3kg / Sqm and minimum 3mm thick reinforced with polyester non woven fabric weight not less than 150 gms / Sqm and on primed surface of one coat of approved bituminous [email protected] Ltr per Sqm by torch application method complete all as specified and as directed .

Supply only liquid water proofing compound

M&L plain cement concrete, 1:2:4 type B0 using 12.5mm graded stone aggreage, as in coved fillets of radius 75mm provided at junction of roof and parapet / vertical surfaces, padding concrete to achieve slope as required , platform for water tank on roof slab etc., including necessary form work complete all as specified and directed.

Use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide includingrough finished surfaces complete all as specified and directed.

Erection and removal of structural steel such as Joist, channel or Tee section fixed independently for supporting members of existing structure during the repair complete all as specified and directed. NOTE:- (i)This item is required to support the existing RCC roof members during executed repair work. (ii) Retrived steel materials will be property of the contractor.

Dismantling portions of reinforced cement concrete / chipping of un sound concrete to a depth / thickness 25mm to 100m ,averaging 62.5mm as in roofs , floors, beams, columns, stair cases, landings, chajjas, parapets etc., and similar suspended work ( other than ground floors) and removing rubbish to out side MD land complete all as specified and as directed.

Preparation of surfaces of RCC column, beam, chajja, roof drops, soffit of slab by removing existing cement plaster, hacking out the surface of RCC work for key to a depth of 15mm by gentle chipping manually to make surface rough and thoroughly clened with air and water jet complete all as specified and directed.

Preparation of exposed surfaces of rusted steel reinforcement with metal wire brush, cleaning the rusted surfaces free from loose rust and application of rust remover cum passivator painted with brush on rusted reinforcement @ 0.20 kg per sqm of surfaces of existing reinforcement and removing rust with flex after 24 hrs of application of rust remover with wire brush, sand paper and throughly washed with water through pressure jet and allowing it dry to complete all as specified and directed. Note :- Area of cleaned reinforcement steel shall be measured for the purpose of payment.

Preparation of surfaces of steel reinforcement by cleaning throughly and applying zinc - rust agent as per manufacturer method of application to rebar corrosion protection system to reinforcement @ 3.75 kg per sqm surface of steel reinforcement in two coats complete all as specified and directed.

M&L for augmentation of RCC by using Dr. Miracle system of M/s AAYKA polymers or equivalent of M/s FOSROC / Dr. Fixit, by pressure grouting @1 to 2 kg per sqm complete all as specified and directed.

M&L for providing AQUAVENTS of M/s AAYKA polymers or equivalent of M/s FOSROC / Dr. Fixit by moisture release system in roofs complete all as specified and directed.

M&L for providing AQUAVENTS of M/s AAYKA polymers or equivalent of M/s FOSROC / Dr. Fixit by moisture release system in walls complete all as specified and directed.

M&L for polymer modified polymer coat with MRP glass membrane on roof surface by using AQUAPROOF 102 of M/s AAYKA polymers @ 4 kg per sqm complete all as specified and as directed.

M&L for ESKOO heat reflective cum water proofing system @2 kg per sqm of M/s AAYKA polymers or equivalent of M/s FOSROC / Dr. Fixit complete all as specified and as directed.

M&L for micro cement concrete of M/s AAYKA polymers or equivalent of M/s FOSROC / Dr. Fixit , pre packed single component, chloride free , sulphate free, non shrink, free flow, self compacting / ready to use after mixing of required quantity of water as per manufacturer instructions is required to achieve high strength, dual shrinkage, compensated, micro complete repair with compressive strength of 40 Mpa at 28 days complete all as specified and as directed.

S&F 12mm TS dowel pins/ staple/ shear pins M/s AAYKA polymers or equivalent of M/s FOSROC / Dr. Fixit including drilling holes in concrete and epoxy for grouting the pins complete all as specified and as directed .

S&F 6mm TS dowel pins/ staple/ shear pins M/s AAYKA polymers or equivalent of M/s FOSROC / Dr. Fixit including drilling holes in concrete and epoxy for grouting the pins complete all as specified and as directed .

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc . removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, complete all as specified and directed.

M&L point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multi stranded copper conductor 1.5 sq mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and including heavy duty non metallic PVC rigid conduit of 25mm dia with accessories concealed in wall/roof/floor etc, ISI marked with1.6mm thick mild steel/prestressed steel sunken/concealed box (with earth dolly) duly painted two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally, with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, inciuding PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly for,one way switch One light/ fan point controlled by one, one way switch 5Amps complete all as specified and directed.

All as per serial Item No.84 above for one 3 pin socket outlet 5 Amps on independent board complete all as specified and as directed

All as per serial Item No.84 above but for one 3 pin socket outlet 5 Amps on the same board with other switches complete all as specified and as directed.

All as per serial Item No.84 above but for 15 Amps 5/6 pin socket point on independent board with 4.00 Sqmm PVC insulated FRLS multi-stranded copper conductor with 4.00 Sqmm PVC insulated FRLS multi-stranded copper conductor as earth wire complete all as specified and directed .

M&L switch piano, flush type, single pole, one way, 5/6 Amps, 230 Volts complete all as specified and as directed.

M&L switch piano 15 Amp flush type single pole one way with ISI marked, complete all as specified and as directed.

M&L socket outlet 5/15 Amps 2-in-1,3/5 pin 230V AC flush type, complete all as specified and directed.

M&L socket outlet 5Amps 2-in-1,3 pin 230V AC flush type, complete all as specified and directed.

M&L Exhaust fan of 450 mm sweepwith louvers 230/240 volt complete with bracket frame and fixing the exhaust fan on the bracket frame and making necessary electric connection complete all as specified and as directed .

M&L ceiling rose, 3 phase / PVC / Polycarbonate, isolated bodycomplete all as specified and as directed.

S&F LED light fitting 20W 230 volt, energy efficient batten type ( integrated driver), 6500K colour temp, decorative type with all accessories internally pre wired including tube rod and connectiong up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed Make : Havells Cat Part No. LHEXBXPNIN1W020 or techno commercially equivalent model of make Bajaj /Philips / CG

M&L lamp holder, PVC / poly carbonate type with black plate suitable for batten fittings complete all as specified and directed.

M&L submain wiring with two runs of 6 sqmm with one run of 6 Sqmm earth wire of 1100V grade FRLS PVC insulated multi-stranded copper conductor, single core cable conforming to IS 694 drawn through and including 25mm dia PVC rigid conduit with accessories concealed on wall / ceiling with PVC saddles and cadmium plated steel screws and connected to common earth dolly complete all as specified and directed. Note :- Three runs of 6 sqmm and one run of PVC conduit shall be measured as one length for the purpose of measurement.

M&L single pole and neutral enclosure with two pin earth industrial plug and socket with one MCB SP 20 Amps complete all as specified and as directed.

M&L factory made distribution board in sheet metal enclosure in double door with 200A rated bus bar,SPN 4 way, 440 volt for fixing MCB's complete all as specified and as directed.

M&L factory made distribution board in sheet metal enclosure in double door with 200A rated bus bar,SPN 8 way, 440 volt for fixing MCB's complete all as specified and as directed.

M&L Isolator TPN 4 pole, 63 amps complete all as specified and as directed .

M&L Isolator SPN 40 amps complete all as specified and as directed .

M&L MCB SP ‘C’ Curve 10KA , 6 to 40 amps 230V complete all as specified and as directed .

Supply,testing and installation of electric storage geyser of capacity 50 Ltrs, 230Volts, AC, 50Hz, 5 star rated ISI marked with vertical mounting type comprising of heating element 2000 watt,puff insulation,both power indicating LED lamp and heating indicating LED lamp neccasry suitable 3 core copper cable,suitable plug top, inlcluding supply and fixing of inlet and out let connection to geyser with steel grip,chromium plated PVC connection of 600mm in length - 02 Nos (one for inlet GI pipe and other one for outlet connection) suitable to connect inlet GI pipe 15mm dia and out let GI pipe 15mm dia (out let PVC connection should be capable to withstand the designed temparature of Geyser) and geyser shall be fixed on wall surface with wall mount bracket and 10 cm anchor bolts as required inclduing all necessary plumbling works and civil works complete all as directed and as specified. Make :- Havells Model No. GHWAMESWH050 or techno commercially equivalent make in V guard / Jaquar / CH

S&F in repairs gun metal Gate valves with iron wheel srewed both end for size 15 mm dia pipe complete all as specified and directed .

Taking down ceiling fan / exhaust fan of any size and sweep from its position and dismantling for servicing including removal of bearing, bushes, condenser, connector, flaxible cord,split pin etc if required, removing old grease and refill fresh, lubricating bushes alongwith new washers including spray painting with a coat of Ist quality synthetic enamel paint of approved colour including preparation of old painted surfaces, cleaning etc and printing the fan numbers with black paint and re- assamble the same including connecting to electric system, testing etc and fixing/ hanging to position as directed complete all as specified and as directed.

M&L earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as specified and as directed. NOTE :(i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-( ii) Item includes the cost of GI pipe up to 7.5m for protection of earth wire. any variation in length beyond 7.50 m shall be measured separately.(iii) Item includes cost of lead wire up to 7.5 m Any variation in length beyond 7.50 m shall be measured separately.(iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

AMBEY MAA CONSTRUCTION COMPANY

Godara Construction and General Suppliers

M.D. CONSTRUCTION CO.