Construction of Additional Girls Dormitory at various JNVs in the state of Odisha

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

1 Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as

10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and for all lift, as

directed by Engineer-in charge.

2 Extra for every additional lift of 1.5 m or part thereof

in excavation /

banking excavated or stacked materials.

Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as

3 10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and lift upto 1.5 m,

as directed by Engineerin-charge.

4 Excavating trenches by mechinical / manual means

of required width for pipes, cables, etc including

excavation for sockets, and dressing of sides,

ramming of bottoms, for all depth, including getting

out the excavated soil, and then returning the soil as

required, in layers not exceeding 20 cm in depth,

including consolidating each deposited layer by

ramming, watering, etc. and disposing of surplus

excavated soil as directed, within a lead of 50 m.

All kind of soil 2.10.1 -

Pipes, cables etc, not exceeding 80 mm dia. 2.10.1.2 506.00 Metre 352.15 1,78,187.90

5 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers

not exceeding 20cm in depth,consolidating each

deposited layer by ramming and watering, lead upto

50 m and lift upto 1.5 m.

6 Supplying and filling in plinth with sand under floors,

including watering, ramming,consolidating and

dressing complete.

7 Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

lead of 5km also including ramming and watering of

the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete.

8 Surface dressing of the ground including removing

vegetation and in-equalities not exceeding 15 cm

deep and disposal of rubbish, lead up to 50 m and lift

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

9 Supplying chemical emulsion in sealed containers

including delivery as specified. 2.34 -

Chlorpyriphos/ Lindane emulsifiable concentrate of

10 Along external wall where the apron is not provided

using chemical emulsion @ 7.5 litres/ sqm of the

vertical surface of the substructure to a depth of

300mm including excavation channel along the wall

& rodding etc. complete 2.35.1 -

With Chlorpyriphos/ Lindane E.C. 20% with 1%

B Concrete Work -

11 Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived

from natural sources : 6 graded stone aggregate 20

mm nominal size derived from natural sources)

12 Providing and laying damp-proof course 50mm thick

with cement concrete 1:2:4 (1 cement : 2 coarse

sand (zone-III) derived from natural sources : 4

graded stone aggregate 20mm nominal size derived

from natural sources). 4.11 245.06 SQM 495.75 1,21,489.49

13 Extra for providing and mixing water proofing

material in cement concrete work in doses by weight per

of cement as per manufacturer's specification. 50kg

14 Providing & applying a coat of residual petroleum

bitumen of grade of VG-10 of approved quality using

1.7kg per square metre on damp proof course after

cleaning the surface with brushes and finally with a

piece of cloth lightly soaked in kerosene oil.

15 Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement : 3 coarse sand (zone-III)

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from natural

sources) over 75mm thick bed of dry brick ballast 40

mm nominal size, well rammed and consolidated and

grouted with fine sand,including necessary

excavation,levelling & dressing & finishing the top

C Reinforced Cement Concrete -

16 Centering and shuttering including strutting, propping

etc. and removal of form for all heights :

(a) Foundations, footings, bases of columns, etc. for

(b) Walls (any thickness) including attached pilasters,

plinth and string courses etc. 5.9.2 17.50 SQM 842.50 14,743.75

(c) Suspended floors, roofs, landings, balconies and

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

(d) Lintels, beams, plinth beams, girders, bressumers

(e) Columns,Pillars, Piers, Abutments, Posts and Struts.

17 Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

and binding all complete upto plinth level. Thermo-

Mechanically Treated bars of grade Fe-500D or

18 Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

and binding all complete above plinth level. Thermo-

Mechanically Treated bars of grade Fe-500 D or

19 providing and laying in position ready mixed or site

batched design mix cement concrete for

reinforced cement concrete work; using coarse

aggregate and fine aggregate derived from

natural sources, portland pozzolana / ordinary

portland /portland Slag cement, admixtures in

recommended proportions as per iS: 9103 to

accelerate / retard setting of concrete, to improve

durability and workability without impairing strength;

including pumping of concrete to

site of laying, curing, carriage for all leads; but

excluding the cost of centering, shuttering,

finishing and reinforcement as per direction of the

engineer-in-charge; for the following grades

Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be

payable separately. in case the cement content in

design mix is more than 110% of the specified

minimum cement content, the contractor shall have

discretion to either re-design the mix or bear the cost

of extra cement. 5.33 -

(I) All works upto plinth level -

concrete of M25 grade with minimum cement

II All works above plinth level -

concrete of M25 grade with minimum cement

D Masonry Work -

Half brick masonry with non modular fly ash bricks of

class designation 10, conformingio IS :12894, in

super structure above plinth upto floor V level.

Cement mortar 1 : 4 (1 cement : 4 coarse sand) 6.45.2 697.90 SQM 1123.80 7,84,300.02

21 Brick work with non modular fly ash bricks

conforming to IS:12894, class designation 10

average compressive strength in superstructure

above plinth level up to floor V level in : Cement

mortar 1:6 (1 cement : 6 coarse sand)

22 Extra for providing and placing in position 2 Nos

6mm dia. M.S. bars at every third course of half brick

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

E Cladding Work -

23 Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters,

window sills , facias and similar locations of required

size, approved shade, colour and texture laid over 20

mm thick base cement mortar 1:4 (1 cement : 4

coarse sand), joints treated with white cement, mixed

with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges to

give high gloss finish etc. complete at all levels.

Granite stone slab of colour black, Cherry/Ruby red

24 Providing edge moulding to 18mm thick marble

stone counters, Vanities etc. including machine

polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-

Charge. 0.00 -

25 Extra for fixing marble /granite stone over and above

corresponding basic item, in facia and drops of width

upto 150 mm with epoxy resin based adhesive

including cleaning etc. complete.

26 Extra for providing opening of required size & shape

for wash basins/ kitchen sink in kitchen platform,

vanity counters and similar location in

marble/Granite/stone work including necessary holes

for pillar taps etc. including moulding, rubbing and

polishing of cut edges etc. complete.

27 Providing and fixing Ist quality ceramic glazed wall

tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in

all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-

Charge, in skirting, risers of steps and dados, over

12 mm thick bed of cement mortar 1:3 (1 cement : 3

coarse sand) and jointing with grey cement slurry @

3.3kg per sqm, including pointing in white cement

mixed with pigment of matching shade complete.

(Size-300x450 )

F Wood and PVC Work -

29 Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) nondecorative type,

core of block board construction with frame of 1st

class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and

face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt

hinges with necessary screws 9.21.1 127.68 SQM 2392.65 3,05,493.55

Providing and fixing aluminium handles ISI

marked anodised (anodic coating not less than

grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade

with necessary screws etc. complete :

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

Providing and fixing aluminium hanging floor

door stopper ISI marked anodised (anodic

coating not less than grade AC 10 as per IS

:1868) transparent or dyed to required colour

or shade with necessary screws etc.

Twin rubber stopper 102.00 70.40 7,180.80

32 Providing & fixing bright finished brass 9.76 Each 854.65 -

100mm mortice latch and lock with 6 levers

and a pair of lever handles with necessary

screws etc. complete (Best make of approved

Providing & fixing bright finished brass night

33 latch of approved quality including necessary 9.78 Each 1183.3 -

screws etc. complete 7.00 8,283.10

Providing & fixing IS:3564 marked aluminium

Die cast body tubular type universal hydraulic

34 door closer with necessary 9.83 Each 1124.85 -

accessories and screws etc. complete

35 Providing and fixing aluminium sliding door 9.96 -

bolts ISI marked anodised (anodic coating not

less than grade AC 10 as per IS: 1868)

transparent or dyed to required colour or

shade with nuts and screws etc. complete:

36 Providing and fixing aluminium tower bolts ISI 9.97 -

marked anodised (anodic coating not less than -

38 Providing and fixing factory made single extruded

WPC (Wood Polymer Composite) solid

door/window/Clerestory windows & other

Frames/Chowkhat comprising of virgin PVC polymer

of K value 58-60 (Suspension Grade), calcium

carbonate and natural fibers (wood powder/ rice

husk/wheat husk) and non toxic additives (maximum

toxicity index of 12 for 100 gms) fabricated with miter

joints after applying PVC solvent cement and

screwed with full body threaded star headed SS

screws having minimum frame density of 750

kg/cum, screw withdrawal strength of 2200 N (Face)

& 1100 N (Edge), minimum compressive strength of

58 N/mm2, modulus of elasticity 900 N/mm2 and

resistance to spread of flame of Class A category

with property of being termite/borer proof,

water/moisture proof and fire retardant and fixed in

position with M.S hold fast/lugs/SS dash fasteners of

required dia and length complete as per direction of

Engineer-In- Charge. (M.S hold fast/lugs or SS dash

fasteners shall be paid for separately).

Note: For WPC solid door/window frames, minus

5mm tolerance in dimensions i.e depth and width of

profile shall be acceptable. Variation in profile

dimensions on plus side shall be acceptable but no

extra payment on this account shall be made

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

39 Providing and fixing factory made single extruded

WPC (Wood Polymer Composite) solid plain flush

door shutter of required size comprising of virgin

polymer of K value 58-60 (Suspension Grade),

calcium carbonate and naturalfibers (wood powder/

rice husk/wheat husk) and non toxic

additives(maximum toxicity index of 12 for 100 gms)

having minimum density of 650 kg/cum and screw

withdrawal strength of 1800 N (Face) & 900 N(Edge),

minimum compressive strength 50 N/mm2,

modulus of elasticity 850 N/mm2 and resistance to

spread of flame of Class A category with property of

being termite/borer proof, water/moisture proof and

fire retardant and fixing with stainless steel butt

hinges ofrequired size with necessary full body

threaded star headed counter sunk S.S screws, all

as per direction of Engineer-In- Charge. (Note:

stainless steel butt hinges and necessary S.S screws

shall be paid separately)

40 Providing and fixing M.S. grills of required pattern in

frames of windows etc. with M.S. flats, square or

round bars etc. including priming coat with approved

steel primer all complete.

G Steel Work -

Providing and fixing in position collapsible steel

shutters with vertical channels 20x10x2 mm and

braced with flat iron diagonals 20x5 mm size, with

top and bottom rail of T-iron 40x40x6 mm, with 40

mm dia steel pulleys, complete with bolts, nuts,

locking arrangement, stoppers,

handles, including applying a priming coat of

approved steel primer. 10.30 18.07 SQM 11439.60 2,06,736.45

41 Providing and fixing 1mm thick M.S. sheet door with

frame of 40x40x6 mm angle iron and 3 mm M.S.

gusset plates at the junctions and corners, all

necessary fittings complete, including applying a

priming coat of approved steel primer

Using M.S. angels 40x40x6 mm for diagonal braces

42 Steel work welded in built up sections/ framed work,

including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer

using structural steel etc. as required. In gratings,

frames, guard bar, ladder, railings, brackets,

gates and similar works

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

43 Providing and fixing circular/ Hexagonal cast iron or

M.S. sheet box for ceiling fan clamp, of internal dia

140 mm, 73 mm height, top lid of 1.5 mm thick M.S.

sheet with its top surface hacked for proper bonding,

top lid shall be screwed into the cast iron/ M.S. sheet

box by means of 3.3 mm dia round headed screws,

one lock at the corners. Clamp shall be made of 12

mm dia M.S. bar bent to shape as per standard

44 Providing and fixing stainless steel ( Grade 304)

railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and

making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary

accessories & stainless steel dash fasteners ,

stainless steel bolts etc., of required size, on the top

of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-charge.

45 Providing & fixing fly proof wire gauze to windows,

clerestory windows & doors with M.S. Flat 15x3 mm

and nuts & bolts complete. 10.29.1 317.16 Sqm 844.70 2,67,905.05

46 Chequerred precast cement concrete tiles 22 mm

thick in footpath & courtyard, jointed with neat

cement slurry mixed with pigment to match the shade

of tiles, including rubbing and cleaning etc. complete,

on 20 mm thick bed of cement mortar 1:4 (1 cement:

4 coarse sand). Medium shade pigment using 50%

white cement 50%

47 Kota stone slab flooring over 20 mm (average) thick

base laid over and jointed with grey cement slurry

mixed with pigment to match the shade of the slab,

including rubbing and polishing complete with base

of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

48 Kota stone slabs 20 mm thick in risers of steps,

skirting, dado and pillars laid on 12 mm (average)

thick cement mortar 1:3 (1 cement: 3 coarse sand)

and jointed with grey cement slurry mixed with

pigment to match the shade of the slabs, including

rubbing and polishing complete.

49 Extra for pre finished nosing in treads of steps of

Kota stone/ sand stone slab. 11.31 615.22 M 191.40 1,17,753.11

50 Extra for Kota stone/ sand stone in treads of steps

and risers using single length above normal size up

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

51 Providing and laying Vitrified tiles in floor in different

sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and

conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid on 20

mm thick cement mortar 1:4 (1 cement:

4 coarse sand) jointing with grey cement slurry @3.3

kg/sqm including grouting the joints with white

cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond

cutter only . Laying of tiles will be done with the notch

trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet for

placing the tiles gently and easily.

52 Providing and laying Polished Granite stone flooring

in required design and patterns, in linear as well as

curvilinear portions of the building all complete as

per the architectural drawings with 18 mm thick stone

slab over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all

complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black,

Cherry/Ruby Red or equivalent

53 Providing and fixing Ist quality ceramic glazed wall

tiles conforming to

IS: 15622 (thickness to be specified by the

manufacturer), of approved

make, in all colours, shades except burgundy, bottle

green, black of

any size as approved by Engineer-in-Charge, in

skirting, risers of steps

and dados, over 12 mm thick bed of cement mortar

1:3 (1 cement : 3

coarse sand) and jointing with grey cement slurry @

including pointing in white cement mixed with

pigment of matching shade

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

54 Providing and fixing tiled false ceiling of specified

materials of size 595x595 mm in true horizontal level,

suspended on inter locking metal grid of hot dipped

galvanized steel sections ( galvanized @ 120 grams/

sqm, both side inclusive) consisting of main "T"

runner with suitably spaced joints to get required

length and of size 24x38 mm made from 0.30 mm

thick (minimum) sheet, spaced at 1200 mm center to

center and cross "T" of size 24x25 mm made of 0.30

mm thick (minimum) sheet, 1200 mm long spaced

between main "T" at 600 mm center to center to form

a grid of 1200x600 mm and secondary cross "T" of

length 600 mm and size 24x25 mm made of 0.30

mm thick (minimum) sheet to be interlocked at

middle of the 1200x600 mm panel to form grids of

600x600 mm and wall

angle of size 24x24x0.3 mm and laying false ceiling

tiles of approved texture in the grid including,

required cutting/making, opening for services like

diffusers, grills, light fittings, fixtures, smoke

detectors etc. Main "T" runners to be suspended

from ceiling using GI slotted cleats of size 27 x 37 x

25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 12.52.4 45.30 SQM 1528.00 69,218.40

mm long dash fasteners, 4 mm GI adjustable rods -

55 18 mm cement plaster in two coats under layer 12

mm thick cement plaster 1:5 (1 cement : 5 coarse

sand) and a top layer 6 mm thick cement plaster 1:3

(1 cement : 3 coarse sand) finished rough with

56 12 mm cement plaster of mix 13.4 -

57 6 mm cement plaster on celling (a) 1:3(1 cement:3

58 Finishing walls with textured exterior paint of

required shade: New work (Two or more coats

applied @ 3.28 ltr/10 sqm) over and including

priming coat of exterior primer applied @ 2.20kg/10

58 Add for plaster drip course/ groove in plastered

surface or moulding to r.c.c. projections.

Applying priming coat: 13.50 -

59 With ready mixed red oxide zink chromate primer of

approved brand and manufacture on steel

galvanised iron/steel works. 13.50.3 4450.00 SQM 67.40 2,99,930.00

60 Painting with synthetic enamel paint of approved

brand and manufacture of required colour to given

and an even shade 13.62 -

Two or more coats on new work over an under coat

of suitable shade with ordinary paint of approved

brand and manufacture 13.62.1 2917.62 SQM 226.25 6,60,111.53

61 Finishing with Deluxe Multi surface paint system for

interiors and exteriors using Primer as per

manufacturers specifications 13.48 -

Two or more coats applied on walls @ 1.25 ltr/10

sqm over and including one coat of Special primer

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

Wall painting with acrylic emulsion paint of approved

brand and manufacture to give an even shade :

One coat 13.82.1 SQM 92.00 -

62 Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to

prepare the surface even and smooth complete.

J ALUMINIUM WORK -

63 Providing and fixing aluminium work for doors,

windows, ventilators

and partitions with extruded built up standard tubular

appropriate Z sections and other sections of

approved make -

For fixed portion 21.1.1 -

Anodised aluminium (anodised transparent or dyed

to required shade according to IS: 1868, Minimum

anodic coating of grade

For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making

for fixing of fittings wherever required including the 21.1.2

of EPDM rubber / neoprene gasket required (Fittings

shall be paid for separately) -

Anodised aluminium (anodised transparent or dyed

to required shade according to IS: 1868, Minimum

anodic coating of grade

64 Providing and fixing glazing in aluminium door,

window, ventilator

shutters and partitions etc. with EPDM rubber /

neoprene gasket

etc. complete as per the architectural drawings and 21.3

the directions of

engineer-in-charge . (Cost of aluminium snap

beading shall be paid

With float glass panes of 5 mm thickness (weight not

less than 12.50 kg/sqm) 21.3.2

less than 20 kg/sqm) -

J Water Proofing -

65 Grading roof for water proofing treatment with 22.14 -

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20mm nominal size)

Digitally signed by JAYA

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

66 Providing and laying in situ five course water

proofing treatment with APP (Atactic Polypropylene)

modified Polymeric memberane over roof consisting

of first coat of bitumen primer @ 0.40 litre per sqm,

2nd & 4th courses of bonding material @ 1.20

kg/sqm, which shall onsist of blown type bitumen of

grade 85/25 conforming to IS : 702, 3rd layer of

roofing membrane APP modified Polymeric

membrane .0 mm thick of 3.00 Kg/ sqm weight

consisting of five layers prefabricated with centre

core as 100 micron HMHDPE film sandwiched on

both sides with polymeric mix and the polymeric mix

is protected on both side with 20 micron HMHDPE

film. 5th, the top most layer shall be finished with

brick tiles of class designation 10 grouted with

cement mortar 1:3 (1 cement : 3 fine sand) mixed

with 2% integral water proofing compound by weight

of cement over a 12 mm layer of cement mortar 1:3

(1 cement : 3 fine sand) and finished neat (item of

laying brick tiles shall be paid for separately).

TOTAL Civil Works 8,18,74,697.39

Digitally signed by JAYA

Construction of Additional Girl's dormatory at JNV, Dist: Balasore, Bolangir, Mayurbhanj, Phulbani, Sambalpur

ABSTRACT OF COST- Pavement & Area Developmet

S.N. DESCRIPTION OF ITEM DSR Unit Rate Amount

1 Clearing Jungle including uprooting of rank vegetation, grass, brush wood, trees and

saplings of girth up to 30 cm measured at a height of 1 m above ground level and

removal of rubbish upto a distance of 50 m outside the periphery of the area

2 Earth work in excavation by mechanical means (Hydraulic excavator) / manual

means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on

plan), including dressing of sides and ramming of bottoms, for all lift, including

getting out the excavated soil and disposal of surplus excavated soil as directed,

within a lead of 50 m.

All kinds of soil.

3 Filling available excavated earth (excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited

layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

4 Supplying and filling in plinth with sand under floors, including watering,

ramming,consolidating and dressing complete. 2.27 130.92 Cum 2123.75 2,78,049.85

7 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne

capacity after excavating earth to an average of 22.5 cm depth, dressing to camber

and consolidating with road roller including making good the undulations etc. and re-

rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

8 Construction of granular sub-base by providing close graded Material conforming to

specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material

by tippers to work site, for all leads & lifts, spreading in uniform layers of specified

thickness with motor grader on prepared surface and compacting with vibratory

power roller to achieve the desired density, complete as per specifications and

directions of Engineer-in-Charge.

With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having

9 Construction of dry lean cement concrete sub base over a prepared sub-grade with

coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not

exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation

after blending to be as per specifications, cement content not to be less than 150

Kg/cum, optimum moisture content to be determined during trial length

construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a

batching plant, transported to site, for all leads & lifts, laid with a mechanical paver,

compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as

per direction of Engineer-in- charge

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/

runways, using cement content as per design mix, using coarse sand and graded stone

aggregate of 40 mm nominal size in appropriate proportions as per approved & specified

design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site,

spreading and compacting mechanically by using needle and surface vibrators, levelling to

required slope/ camber, finishing with required texture, including steel form work with

sturdy M.S. channel sections, curing, making provision for contraction/ expansion,

construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine,

providing and filling joints with approved joint filler and sealants, complete all as per

direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars

to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/

less cement used as per design mix is payable/ recoverable separately.

Cement concrete prepared with batch mixing machine 16.43.1 218.21 cum 10529.35 22,97,609.46

Cement Concrete Road Total Total 47,37,525.86

Internal Pathway

1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual

means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on

plan), including dressing of sides and ramming of bottoms, for all lift, including

getting out the excavated soil and disposal of surplus excavated soil as directed,

within a lead of 50 m.

All kinds of soil.

Internal Pathway

Digitally signed by JAYA

2 Filling available excavated earth (excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited

layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

3 Supplying and filling in plinth with sand under floors, including watering,

ramming,consolidating and dressing complete. 2.27 80.00 Cum 2123.75 1,69,900.00

Internal Pathway

4 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded

aggregate 20 mm nominal size derived from natural sources) 240.00 CUM 7878.50 18,90,840.00

Internal Pathway Kerb

5 Providing and laying 60mm thick faciory made cement concrete interlocking paver

block of M-30 grade made by block making machine with strong vibratory

compaction, of approved size, design & shape, laid in required colour and pattern

over and including 50mm thick compacted bed of coarse sand, filling the joints with

line sand etc. all complete as per the direction of Engineer-in-charge

Internal Pathway

6 Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements

after making the joints dust free with high pressure air jet cleaners, all complete as per Cost for one

direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot cm. depth one

sealing compound impregnated fibre board having impregnation more than 35%, conforming cm. width per

to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.) 16.45 2000.00 metre length. 5.30 10,600.00

Internal Pathway of Paver Block Total 29,58,452.00

External Drainage System along paver block and CC Road

1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual

means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on

plan), including dressing of sides and ramming of bottoms, for all lift, including

getting out the excavated soil and disposal of surplus excavated soil as directed,

within a lead of 50 m.

All kinds of soil.

External drainage system

2 Filling available excavated earth (excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited

layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

3 Supplying and filling in plinth with sand under floors, including watering,

ramming,consolidating and dressing complete. 2.27 38.18 Cum 2123.75 81,093.27

External drainage system

4 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded

aggregate 20 mm nominal size derived from natural sources) 57.28 CUM 7878.50 4,51,248.97

External drainage system

5 Brick work with non modular fly ash bricks conforming to IS:12894, class designation

10 average compressive strength in superstructure above plinth level up to floor V

level : Cement mortar 1:6 (1 cement : 6 coarse sand)

External Drainage system

6 12 mm cement plaster finished with a floating coat of neat cement of mix :

External Drainage Total Total 16,97,600.74

Digitally signed by JAYA

Construction of Additional Girl's dormatory at JNV, Dist: Balasore, Bolangir, Mayurbhanj, Phulbani, Sambalpur

MEP Works ( Building)

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES AMOUNT DSR ITEM

2023 [M.R. ITEM]

Internal electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

1 conduit, with modular switch, modular plate, suitable GI 1.10

box and earthing the point with 1.5 sq.mm. FRLS PVC

insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way modular switch,

2 modular plate, suitable GI box and earthing the point with 1.11 85.00 Point 1562.00 1,32,770.00

1.5 sq.mm. FRLS PVC insulated copper conductor single

core cable etc as required.

Wiring for light/power plug with 2x4 Sq.mm FRLS PVC

insulated, copper conductor, single core cable in

3 surface/recessed PVC conduit alongwith 1 No. 4 Sq.mm 1.12 850.00 Metre 334.00 2,83,900.00

FRLS PVC insulated copper conductor single core cable for

loop earthing as required.

Wiring for light/power plug with 4x4 Sq.mm FRLS PVC

insulated, copper conductor, single core cable in

4 surface/recessed PVC conduit alongwith 2 Nos. 4 Sq.mm 1.13 850.00 Metre 537.00 4,56,450.00

FRLS PVC insulated copper conductor single core cable for

loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with 1.14

the following sizes of FRLS PVC insulated copper conductor,

5 single core cable in surface/ recessed medium class PVC

conduit as required

Supplying and fixing of following sizes of medium class PVC 1.21

conduit along with accessories in surface/recess including

6 cutting the wall and making good the same in case of

recessed conduit as required.

Supplying and fixing stepped type electronic fan regulator 1.25

on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing

modular plate & switch box excluding modular plate as 1.26

Supplying and fixing following size/ modules, GI box

9 alongwith modular base & cover plate for modular switches 1.27

in recess etc as required.

Supplying and fixing suitable size GI box with modular

plate and cover in front on surface or in recess, including

10 providing and fixing 6 pin 5/6 & 15/16 amps modular 1.32 170.00 Each 586.00 99,620.00

socket outlet and 15/16 amps modular switch, connection

etc. as required.

Installation, testing and commissioning of pre-wired,

fluorescent fitting / compact fluorescent fitting of all types,

complete with all accessories and tube etc. directly on

11 ceiling/ wall, including connection with 1.5 sq. mm FRLS 1.41 204.00 Each 206.00 42,024.00

PVC insulated, copper conductor, single core cable and

earthing etc. as required.

Digitally signed by JAYA

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES AMOUNT DSR ITEM

2023 [M.R. ITEM]

Installation, testing and commissioning of ceiling fan,

including wiring the down rods of standard length (upto 30

cm) with 1.5 sq. mm FRLS PVC insulated, copper

12 conductor, single core cable, including providing and fixing 1.45 408.00 Each 339.00 1,38,312.00

phenolic laminated sheet cover on the fan box etc. as

Installation of exhaust fan in the existing opening,

13 including making good the damage, connection, testing, 1.50

commissioning etc. as required.

MCCB, MCB & DB's

Supplying and fixing following way, single pole and neutral,

sheet steel ,MCB distribution board, 240 volts, on surface/

recess, complete with tinned copper busbar, neutral

14 bus bar, earth bar, din bar, interconnections powder 2.3 0.00 0.00

painted including earthing etc. as required. (But

MCB/RCCB/ Isolator).

Supplying and fixing following way, horizontal type

three pole and neutral, sheet steel ,MCB distribution

board, 415 volts, on surface/ recess, complete with

15 tinned copper busbar, neutral bus bar, earth bar, din bar, 2.4

interconnections powder painted including earthing etc.

as required. (But with out MCB/RCCB/ Isolator).

supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA,

C Curve, miniature circuit breaker suitable for inductive

16 load of following poles in the existing MCB DB 2.10

complete with connectoin testing and commissioning

etc.as required.

supplying and fixing following rating,double pole,240

17 V,isolator in the existing MCB DB complete with connectoin 2.12

testing and commissioning etc.as required.

supplying and fixing following rating,four pole,415

18 in the existing MCB DB complete with connectoin 2.13 0.00 0.00

testing and commissioning etc.as required.

supplying and fixing following rating,double pole,240

V,residual current circuit breaker (RCCB),having

19 a sensitivity currrent 30 mA in the eiting MCB DB 2.14

completed with connection ,teting commisoining etc.as

20 EARTHING 0.00 0.00

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure

20.1 with cover plate having locking arrangement and watering 5.2 17.00 Each 6855.00 1,16,535.00

pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50

metre below ground as strip earth electrode, including

connection/ terminating with G.I. nut, bolt, spring, washer

21 etc. as required. (Jointing shall be done by overlapping and 5.9 170.00 Metre 144.00 24,480.00

with 2 sets of G.I. nut bolt & spring washer spaced at

Providing and fixing of Lightning Conductor finial, made of 25 mm dia

300mm ling, G.I. Tube, having single prong at top, with 85 mm dia 6 mm

thick G.I. base plate including holes etc.

complete as required.

Providing and fixing G.I. Tape 20mmx3mm thick on parapat or surface

22.2 of the wall for lightning 6.7 500.00 Mtr 126.00 63,000.00

conductor complete as required. (for Horizontal Run).

Providing and fixing G.I. Tape 20mmx3mm thick on parapat or surface

22.3 of the wall for lightning 6.8 200.00 Mtr 197.00 39,400.00

conductor complete as required. (for Vertical Run).

Earthing with G.I. Earth Pipe 4.5 Meter long , 40mm dia including

accessories, and providing massonry enclosure with cover plate

22.4 having locking arragement and watering pipe etc. with 5.2 10.00 Each 6855.00 68,550.00

charcoal/cock and salt as required.

Digitally signed by JAYA

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES AMOUNT DSR ITEM

2023 [M.R. ITEM]

Supplying and laying 25 mm X 5 mm GI strip at 0.50 meter below

ground/surface as strip earth electrode, including connection/

22.5 terminating with nut, bolt, spring, washer etc. as required (Jointing shall 5.9 100.00 Mtrs. 144.00 14,400.00

be done by overlapping and with 2 sets of G.I. nut bolt & spring washer

spaced at 50 mm)

Providing and fixing 6 SWG dia G.I. wire on surface

23 or in recess for loop earthing along with existing 5.18 34.00 Meter 42.00 1,428.00

recessed conduit/ submain wiring/ cable as required.

Supply, Installation, Testing & Commissioning of recessed type down

lighter complete with lamps & accessories 18 W LED

Supply, Installation, Testing & Commissioning of recess type 2x2,

25 36watt LED Light Fixtures complete with lamps & accessories. NS-14 170.00 Each 5468.71 9,29,680.70

Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5

star rated, ceiling fan with Brush Less Direct Current (BLDC)Motor, class of

insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle

kit, safety rope, copper winding, Power Factornot less than 0.9, Service

Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min ,

350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or

electronic regulator unit for speed control and all remaining accessories

including safety pin, nut bolts,washers, temperature rise=75 degree C

(max.), insulation resistance more than 2 mega ohm, suitable for 230 V,

50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying of approved make Exaust Fan of the following

size and its all accessories suitable for operation on 230V

27 single phase, 50 Hz, AC supply complete as required.-450 NS-15 163.00 Each 1702.93 2,77,577.59

Laying of I no. PVC insulated and and PVC sheathed /XLPE power cable of

1.1 KV grade of following size direct in ground including excavation

28 snad cushioning, protective covering and refilling the

trench etc as required.

1.1 KV Cable End Termination:-Supplying and making indoor cable end

termination with brass double compression gland and aluminium lugs for

29 following size of PVC insulated XLPE Al. Ar. Cable DSR 9.1

of 1.1 KV grade as required.

Providing, laying and fixing following dia G.I. pipe (medium class) in

30 ground complete with G.I. fittings including trenching (75 cm deep)and

re-filling etc. as required.

Supply, installation, testing & commissioning of cubical type LT

panel suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system

having front surface area as per G.A Drawing, fabricated in

compartmentalized (preferably) design from CRCA sheet steel of 2

mm thick for frame work and covers, 3 mm thick for gland, plates i/c

cleaning & finishing complete with 9 tank process for powder coating

in approved shade, having 400 Amp capacity extensible type 4P

Aluminium alloy bus bars of high conductivity, DMC / SMC bus bar

supports, with short circuit withstand capacity of 31 MVA for 1 Sec.,

bottom base channel of MS section not less than 100 mm X 50 mm x 5

mm thick, fabrication shall be done in transportable sections entire

panel shall have a common copper earth bar of size 25 mm x 5 mm at

the rear with 2 Nos. earth stud, solid connections from main bus bar

to switch gears with required size of Al. bus bars and control wiring

with sq. mm. PVC insulated copper conductor S/C cable, cable alleys,

cable gland plates in two half, i/c providing following switch gears :-

1 No. 160Amp Four Pole Moulded Case Circuit Breaker of 25 KA (Ics

160/5A class 1, 5VA CTS 1NO Digital multifunction meter

1 Set of phase indicating lamps with single pole MCB.

1 Set of Breaker 'ON' & 'OFF' / TRIP indicating lamps.

Digitally signed by JAYA

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES AMOUNT DSR ITEM

2023 [M.R. ITEM]

200 Amp 4P Aluminium busbar with coloured heat shrinkable sleeve.

Providing and fixting of 6 Nos. 63 Amp 4P MCB of 10KA (Ics value)

Panel described as above 5.00 Set 82690 4,13,450.00

B Sanitary Installations

Providing and fixing water closet squatting pan (Indian

type W.C. pan ) with 100 mm sand cast Iron P or S trap,

10 litre low level white P.V.C. flushing cistern, including

flush pipe, with manually controlled device (handle

lever) conforming to IS : 7231, with all fittings

1.1 and fixtures complete, including cutting and making 17.1.1 22 Each 6767.40 1,48,882.80

good the walls and floors wherever required: White

Vitreous china Orissa pattern

W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water

closet (European type W.C. pan) with seat and lid, 10 litre low

level white P.V.C. flushing cistern, including flush pipe, with

1.2 manually controlled device (handle lever), conforming to IS : 17.2.1 22 Each 6973.59 1,53,418.98

7231, with all fittings and fixtures complete, including cutting and making

good the walls and floors wherever required

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm

C.P. brass pillar taps, 32 mm C.P. brass waste of standard

2.0 pattern, including painting of fittings and brackets, 17.7

cutting and making good the walls wherever require :

White Vitreous China Wash basin size 630x450 mm with a 17.7.2

single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISI 304 (18/8)

kitchen sink as per IS : 13983 with C.I. brackets and

3.0 stainless steel plug 40 mm, including painting of 17.10

fittings and brackets, cutting and making good the walls

wherever required :

Providing and fixing CP Brass 32mm size Bottle Trap

of approved quality & make and as per the direction

Engineer-in-charge.

Providing & fixing PVC waste pipe for sink or wash 17.28

basin including PVC waste fittings complete

5.1 Semi rigid pipe 17.28.1

Providing and Fixing of C.P. Brass Shower set comprising of

7.0 One No. CP brass Single Lever Concealed Diverter . 68 Each 1607.95 1,09,340.60

8.0 One No. CP brass OH shower head & Shower Arm .

9.0 One No. CP brass Bath Spout. 17 Each 803.70 13,662.90

Including cutting and making good the walls

Shower set as described above.

Providing and fixing 600 x 450mm bevelled edge mirror of 17.31

superior glass (of approved quality) complete with

10.0 6mm thick hard board ground fixed to wooden cleats

brass screws and washers complete.

11.0 Providing and fixing toilet paper holder : 17.34

Providing and fixing PTMT towel rail complete with brackets 17.73

12.0 wooden cleats with CP brass screws with concealed fittings

arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width

12.1 78 mm and effective height of 88 mm, weighing not 17.73.2 85 Each 689.81 58,633.85

less than 190 gms

Providing and fixing health faucet with 1 m long NS-6

tube and wall hook including all fittings approved quality.

Digitally signed by JAYA

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES AMOUNT DSR ITEM

2023 [M.R. ITEM]

Providing & fixing CP brass bib cock of approved 18.49

14.0 quality -

conforming IS 8931:

Providing and fixing C.P. brass long body bib cock of

15.0 approved quality conforming to IS standards and weighing 18.51 -

not less than 690 gms.

Providing and fixing CP brass angle valve for basin

16.0 mixer and geyser points of approved quality confirming IS: 18.53 -

17.0 WATER SUPPLY -

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold water

supply, including all CPVC plain & brass threaded fittings,

17.1 including fixing the pipe with clamps at 1.00 m spacing. 18.7 -

This includes jointing of pipes & fittings with one step

CPVC solvent cement and testing of joints complete as

per direction of

Engineer in Charge.

18.0 Internal work - Exposed on wall -

18.1 20 mm nominal outer dia Pipes 18.7.2 850 Metre 325.96 2,77,066.00

18.2 25 mm nominal outer dia Pipes 18.7.3 850 Metre 390.71 3,32,103.50

18.3 32 mm nominal outer dia Pipes 18.7.4 850 Metre 504.74 4,29,029.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes

19.0 jointing of pipes & fittings with one step CPVC solvent 18.8 -

cement and the cost of cutting chases and making good

the same including testing of joints complete as per

Concealed work, including cutting chases and making good

19.1 the walls etc. -

19.2 20 mm nominal outer dia Pipes 18.8.2 1020 Metre 523.08 5,33,541.60

Providing and placing on terrace (at all floor

levels) polythene water storage tank of approved

20.0 brand and manufacture with cover and suitable 18.48 51000 Litre 10.70 5,45,700.00

locking arrangement and making necessary holes for inlet

, outlet and overflow pipes but without fittings and the

base support for tank.

Providing and fixing forged brass ball valve of brass NS-7

body with hard chrome plated steel ball inside PTFE

21.0 (Teflon) seat & ring with chrome plated centre handle

with female BSP

threads complete in all respects.

21.1 20 mm nominal bore NS-7-1 85 Each 346.76 29,474.60

21.2 25 mm nominal bore NS-7-2 85 Each 475.50 40,417.50

21.3 32 mm nominal bore NS-7-3 85 Each 745.43 63,361.55

21.4 40 mm nominal bore NS-7-4 85 Each 1290.49 1,09,691.65

21.5 50 mm nominal bore NS-7-5 85 Each 1819.98 1,54,698.30

22.0 INTERNAL DRAINAGE

Providing and laying cement concrete in 1:2:4 ( 1cement : 4.1.3

22.1 2 Coarse sand : 4 graded stone aggregate 20 mm nominal 9 Cum 7665.78 65,159.13

size ) and curing complete, including cost of form work.

Providing and fixing to the inlet mouth of rain water

23.0 pipe cast iron grating 15 cm diameter and weighing not 12.44 85 Each 54.7 4,649.50

less than 440 grams.

Providing, fixing, jointing and testing in position of ISI

marked UV stabilized UPVC pipes for soil, waste,

and vent, Type-B as per IS : 13592 suitable for

rubber ring joints for vertical pipes and solvent

cement joints for horizontal pipes, including all

neccessary specials and fittings (confirming to

IS:14735) i.e. bends, tees, junctions (with or without

doors), reducers, WC connectors, couplers, cowels,

clamps, long radius / swept bend at bottom of pipe,

24.0 (All connections from horizontal to vertical stacks must be

through swept type fitting) hangers, rubber rings, clean

outs, C P Grating for any waste connection from washing

machine etc. fixing at wall / ceiling / floor level

supported by clamp & hangers etc. inside duct /

suspended from floor under false ceiling for proper

completion of the work. The rubber ring shall confirm

to IS:5382. (Make : Supreme / Astral / Ashirwad /

Finolex) (Pipe support : Intellotech / Easyflex / Chilly)

Digitally signed by JAYA

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES AMOUNT DSR ITEM

2023 [M.R. ITEM]

Providing, fixing, jointing and testing in position ISI

marked (IS:4985) UPVC pipes of min 6 Kg/ Sq cm

rating with fitting for waste pipe from fixtures to floor

trap including reduces, enlarger, socket, couplers,

25.0 bends, tees etc including fixing at wall/ ceiling level NS-8

supported by clamp & hangers etc. The work includes

cutting holes in wall/ floors/ slabs and making good the

same with cement concrete 1:2:4 complete as

required. (Make : Supreme / Astral /

Providing & fixing UPVC Floor trap of self cleansing design

26.0 with CP Jali complete in all respects. (Make : NS-9

Astral / Ashirwad / Finolex)

S-Trap type Floor Trap 110 x 110 mm (50 mm seal) NS-9-1

P-Trap type Floor Trap 110 x 110 mm (Long type - 50 mm NS-9-2

Providing and fixing uPVC agricultural pipes conforming to

IS:4985 (6 kg/sqcm) including all fittings, e.g.

27.0 couplings, tees, bends, reducers and screwed adoptors NS-10

jointing with solvent cement joint as per

recommendations. [for Rain Water Pipes]

Providing and fixing cast brass floor clean out plug

with suitable insert keys for opening, male threaded joint

28.0 with GI threaded socket drip seal to soil / waste pipe of CI NS-11 85 Each 664.45 56,478.25

pipe as required complete as per drawing approved

direction of engineer in charge.-100 mm dia

Providing, laying and jointing glazed stoneware pipes class 19.1

SP-1 with stiff mixture of cement mortar in the proportion

29.0 of 1:1 (1 cement : 1 fine sand) including testing of -

etc. complete :

Providing, laying and jointing HDPE Double Wall Coil (DWC)

SN-8 Grade pipes confirming to IS: 16098 including

all fittings wherever required e.g., tees, bends of any

30.0 degree, couplings, adapters, plugs, unions etc. and NS-12 -

jointing as manufacturer recommondation etc.

including testing of

joints etc. complete.

Digitally signed by JAYA

External Development- Septic Tank

S.N. DESCRIPTION OF ITEM DSR Quantity Unit Rate Amount

II Septic Tank

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over areas

(exceeding 30cm in depth. 1.5 m in width as well as

1 10 sqm on plan) including disposal of excavated

earth, lead upto 50m and lift upto 1.5m, disposed

levelled and neatly dressed. 2.6

2 Extra for every additional lift of 1.5 m or part thereof

in excavation /

banking excavated or stacked materials.

All kinds of soil 2.26.1 63.300 CUM 126.80 8,026.44

Supplying and filling in plinth with sand under

floors, including watering, ramming, 2.27 11.800 CUM 2123.75 25,060.25

Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded

aggregate 40 mm nominal size) 4.1 17.100 CUM 6812.00 1,16,485.20

providing and laying in position ready mixed or site

batched design mix cement concrete for

reinforced cement concrete work; using coarse

aggregate and fine aggregate derived from

natural sources, portland pozzolana / ordinary

portland /portland Slag cement, admixtures in

recommended proportions as per iS: 9103 to

accelerate / retard setting of concrete, to improve

5 durability and workability without impairing strength;

including pumping of concrete to

site of laying, curing, carriage for all leads; but

excluding the cost of centering, shuttering,

finishing and reinforcement as per direction of the

engineer-in-charge; for the following grades

Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be

payable separately. in case the cement content in

design mix is more than 110% of the specified

minimum cement content, the contractor shall have

discretion to either re-design the mix or bear the cost

of extra cement.

(I) All works upto plinth level

concrete of M25 grade with minimum cement

Centering and shuttering including strutting, propping

etc. and removal of form for all heights :

Lintels, beams, plinth beams, girders, bressumers

and cantilevers 5.9.5 27.100 SQM 736.40 19,956.44

Digitally signed by JAYA

Suspended floors, roofs, landings, balconies and

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

8 and binding all complete upto plinth level. Thermo-

Mechanically Treated bars of grade Fe-500D or

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers

not exceeding 20cm in depth, consolidating each

deposited layer by ramming

and watering, lead up to 50 m and lift upto 1.5 m.

Brick work with non modular fly ash bricks

conforming to IS:12894, class designation 10

10 average compressive strength in superstructure

above plinth level up to floor V level

Cement mortar 1:6 (1 cement : 6 coarse sand) 6.34.2 61.000 CUM 8752.55 5,33,905.55

Half brick masonry with non modular fly ash bricks of

class designation 10, conformingio IS

:12894, in super structure above plinth and upto floor

Cement mortar 1 : 4 (1 cement : 4 coarse sand)

12 12 mm cement plaster of mix : 13.4

13 Neat cement punning 13.18 328.800 SQM 79.95 26,287.56

Supplying and fixing C.I. cover without frame for

manholes : 560 mm diameter C.I. cover (heavy duty)

the weight of the cover to be not less than 108 kg

Making soak pit 2.5 m diameter 3.0 m deep with

45x45 cm dry brick honey comb shaft with bricks and

15 S.W. drain pipe 100 mm diameter and 1.20 m long

complete as per standard

with common burnt clay F.P.S. (non modular) bricks

of class designation 7.5 19.32.1 10.000 EACH 26861.90 2,68,619.00

Total Total 26,00,121.15

Digitally signed by JAYA

Construction of Additional Girl's dormatory at JNV, Dist: Balasore, Bolangir, Mayurbhanj, Phulbani, Sambalpur

Sl. No. DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

NS-1 SUB HEAD-XVIII :-EXTERNAL LIGHTING WORK Units No Rate DSR Amount Non DSR Amount

Supplying,installation,testing and commissioning of 6.0

meter Height hot dip galvanised continously tapered

(bolt fixing type) octagonal Pole including 90 watt LED

Fixture, colour cool white , integral driver, protection IP 65,

CLASS I with top 70 mm dia and bottom 130 mm dia made

of 3 mm thick H T sheet Steel conforming to grade S 355

complete with G I base plate of size 220 mm (L) X 220 mm

(B) X 16 mm thickness welded at bottom of pole complete

with 4 Nos 20 mm dia 750 mm long foundation bolts

confroming to EN 8 grade, inbuilt / Vandal resistance,

weathproof electrical junction box having terminal block,

MCB etc mounted on bakelite sheet for looping in

/looping out of cables, with flush door having locking

arrangement, earthing arrangement (at atleast 0.5 m

height) and mounted on RCC foundation of size 450 mm x

450 mm x 1000 mm in ground and 200 mm above ground

level with foundation bolt duly embeded before casting and

supply and embedding of suitable size HDPE pipe sleeve

for cable entry. complete including erection of Pole

complete in all respect as required.

2.0 NS-2 EXTERNAL FEEDER PANEL

Supply, installation, testing & commissioning of cubical

type LT panel suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC

supply system having front surface area as per G.A

Drawing, fabricated in compartmentalized (preferably)

design from CRCA sheet steel of 2 mm thick for frame work

and covers, 3 mm thick for gland, plates i/c cleaning &

finishing complete with 9 tank process for powder coating

in approved shade, having 125Amp capacity extensible type

4P Aluminium alloy bus bars of high conductivity, DMC /

SMC bus bar supports, with short circuit withstand capacity

of 31 MVA for 1 Sec., bottom base channel of MS section

not less than 100 mm X 50 mm x 5 mm thick, fabrication

shall be done in transportable sections entire panel shall

have a common copper earth bar of size 25 mm x 5 mm at

the rear with 2 Nos. earth stud, solid connections from

main bus bar to switch gears with required size of Al. bus

bars and control wiring with sq. mm. PVC insulated copper

conductor S/C cable, cable alleys, cable gland plates in two

half, i/c providing following switch gears :-

1 No. 40 Amp 4P MCB with following accessories-

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

50 Amp 4P Aluminium busbar with coloured heat

shrinkable sleeve.

i) 4 Nos. 25 Amp 4P Miniature Circuit Breaker.

iii) 1 Nos. 25 Amp DP Miniature Circuit Breaker.

Panel described as above Set 5 25903.773 1,29,518.87

LIGHTING FIXTURE

Supply of LED flood light fixture suitable for Surface / Wall

type mounting with Epoxy powder coated die -cast

aluminium housing with heat Sink, toughened glass,

complete with inbuilt electronics driver, mounting bracket,

90 Lumen /watt efficacy, min 7000 Lumen output,

THD<10%, P.F. >0.95, IP 65 rated as required

Supply and drawing of following size of FRLS PVC insulated

copper conductor, single core cable in the existing surface /

recessed steel / PVC conduit as required-

Digitally signed by JAYA

Supply and making end termination with brass

compression gland and aluminium lugs for following size of

PVC Insulated & PVC sheath /XLPE Al conductor cable of 1.1

kv grade as required-

TOTAL SUM 2621417.839

Digitally signed by JAYA

Construction of Additional Girl's dormatory at JNV, Dist: Balasore, Bolangir, Mayurbhanj, Phulbani, Sambalpur

S.N. DESCRIPTION OF ITEM DSR Unit Rate Amount

External Water Supply

Providing and fixing G.I. pipes complete with G.I. fittings 18.12

1 including trenching and refilling etc.

50 mm dia nominal bore 18.12.6 246.54 Metre 762.15 1,87,902.75

65 mm dia nominal bore 18.12.7 714.45 Metre 896.60 6,40,574.08

80 mm dia nominal bore 18.12.8 232.62 Metre 1041.70 2,42,323.38

2 Painting G.I. pipes and fittings with two coats of anti-

corrosive bitumastic paint of approved quality :

50 mm dia nominal bore 18.40.6 246.54 Metre 30.50 7,519.56

65 mm dia nominal bore 18.40.7 714.45 Metre 37.85 27,041.86

80 mm dia nominal bore 18.40.8 232.62 Metre 44.00 10,235.41

3 Providing and filling sand of grading zone V or coarser

grade, allround the G.I. pipes in external work :

50 mm dia nominal bore 18.41.6 246.54 Metre 173.25 42,713.57

65 mm dia nominal bore 18.41.7 714.45 Metre 273.45 1,95,365.81

80 mm dia nominal bore 18.41.8 232.62 Metre 281.80 65,553.16

Constructing masonry Chamber 30x30x50 cm inside, in 18.32

brick work in cement mortar 1:4 (1 cement :4 coarse

sand) for stop cock, with C. I. surface box 100x100 x75

mm (inside) with hinged cover fixed in cement concrete

slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size), i/c necessary

4 excavation, foundation concrete 1:5:10 ( 1 cement : 5

fine sand : 10 graded stone aggregate 40 mm nominal

size ) and inside plastering with cement mortar 1:3 (1

cement : 3 coarse sand) 12mm thick, finished with a

floating coat of neat cement complete as per standard

With common burnt clay F.P.S.(non modular) bricks of 18.32.1

class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in 18.33

brick work in cement mortar 1:4 (1 cement : 4 coarse

sand) for sluice valve, with C.I. surface box 100mm top

diameter, 160 mm bottom diameter and 180 mm deep (

inside) with chained lid and RCC top slab 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20mm

5 nominal size ) , i/c necessary excavation, foundation

concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone

aggregate 40 mm nominal size) and inside plastering

with cement mortar 1:3 (1 cement : 3 coarse sand) 12

mm thick, finished with a floating coat of neat cement

complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of 18.33.1

class designation 7.5 12.00 1,30,324.80

Digitally signed by JAYA

Constructing masonry Chamber 90x90x100 cm inside, in 18.34

brick work in cement mortar 1:4 (1 cement : 4 coarse

sand) for sluice valve, with C.I. surface box 100 mm top

diameter, 160 mm bottom diameter and 180 mm deep

(inside) with chained lid and RCC top slab 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size ), i/c necessary excavation, foundation

6 concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone

aggregate 40 mm nominal size ) and inside plastering

with cement mortar 1:3 (1 cement : 3 coarse sand) 12

mm thick, finished with a floating coat of neat cement

complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of 18.34.1

class designation 7.5

Providing and fixing G.I. Union in G.I. pipe including 18.46

cutting and threading the pipe and making long screws

etc. complete (New work) :

50 mm dia nominal bore 18.46.6 12.00 Each 823.80 9,885.60

65 mm dia. nominal bore 18.46.7 42.00 Each 1136.80 47,745.60

80 mm dia. nominal bore 18.46.8 8.00 Each 1207.95 9,663.60

Supplying, fixing, testing and commissioning of butterfly 18.11

valve of PN 1.6 rating with bronze/gunmetal seat duly ISI

marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required

Providing and fixing C.I. double acting air valve of 18.59

approved quality with

9 bolts, nuts, rubber insertions etc. complete (The tail

pieces, tapers etc if

required will be paid separately) :

Digitally signed by JAYA

Construction of Additional Girl's dormatory at JNV, Dist: Balasore, Bolangir, Mayurbhanj, Phulbani, Sambalpur

DSR DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

B SUBHEAD OF INTERNAL & EXTERNAL PLUMBING WORKS

E) RAIN WATER WORK

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A including jointing with seal ring

conforming to IS : 5382 leaving 10

mm gap for thermal expansion, (i) Single socketed pipes

Providing and fixing on wall face unplasticised - UPVC moulded

fittings/ accessories for unplasticised Rigid PVC rain water pipes

5.02 12.42 conforming to IS : 13592 Type A including jointing with seal ring

conforming to IS : 5382 leaving 10 mm gap for thermal

Making khurras 45x45 cm with average minimum thickness of 5 cm

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1

5.03 12.22 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement Each 150 298.25 44,737.50

: 3 coarse sand) and a coat of neat cement, rounding the edges

and finishing the outlet complete.

TOTAL FOR RAIN WATER DRAINAGE 2,72,730.00

F) EXTERNAL WATER SUPPLY WORKS

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings This includes jointing of pipes

& fittings with one step CPVC solvent cement, trenching, refilling &

testing of joints complete as per direction of Engineer in

18.9.5 40mm nominal dia Pipes Metre 200 563.05 1,12,610.00

e) 18.9.6 50mm nominal dia Pipes Metre 100 794.25 79,425.00

f) 18.9.7 65mm nominal dia Pipes Metre 200 1,674.40 3,34,880.00

Providing and filling sand of grading zone V or coarser grade alround

1.02 18.41 the CPVC pipes

in external work.

d) 18.41.5 40mm diameter pipe Metre 200 167.00 33,400.00

e) 18.41.6 50mm diameter pipe Metre 100 173.25 17,325.00

f) 18.41.7 65mm diameter pipe Metre 200 273.45 54,690.00

Providing and fixing gun metal gate valve with C.I. wheel of

1.03 18.17 approved quality

(screwed end) :

a) 18.17.3 40 mm nominal bore Metre 20 826.10 16,522.00

b) 18.17.4 50 mm nominal bore Metre 10 1,026.65 10,266.50

c) 18.17.5 65 mm nominal bore Metre 5 1,742.15 8,710.75

TOTAL FOR RAIN WATER DRAINAGE 6,67,829.25

G) EXTERNAL SEWER & STORM WORKS

Digitally signed by JAYA

DSR DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

Providing and fixing square mouth S.W. gully trap grade 'A' complete

with C.I. Grating brick masonary chamber with bricks of class

designation 75 and water tight C.I. Cover with frame of 300x300

mm size (inside) the weight of cover to be not less than 4.50 kg

frame to be not less than 2.70 kg as per standard design

19.4 .1 100x100 mm size P type

with common burnt clay F.P.S.(non module) brick of class designation

Constructing brick masonary road gully chamber 50x45x60 cm

with bricks of class designation 75 in cement mortar 1:4 (1

1.02 cement :4 coarse sand ) including 500x450 mm

precast RCC horizontal grating with frame complete as per standard

with common burnt clay F.P.S.(non module) brick of class designation

Constructing brick masonry chamber for underground C.I. inspection

chamber and bends with bricks in cement mortar 1:4 (1 cement : 4

coarse sand) C.I. cover with frame (light duty) 455x610 mm

internal dimensions, total weight of cover with frame to be not

less than 38 kg (weight of cover 23 kg and weight of frame 15 kg),

R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded

1.03 19.30 stone aggregate 20 mm nominal size),

foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone

aggregate 40 mm nominal size), inside plastering 12 mm thick with

cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a

floating coat of neat cement on walls and bed concrete etc. complete

per standard design:

Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

19.30.1.1 With common burnt clay F.P.S. (non modular) Each 25 6,937.90 1,73,447.50

bricks of class designation 7.5

1.04 19.31 Extra for depth beyond 45 cm of brick masonry chamber :

For 455x610 mm size With common burnt clay F.P.S. (non modular)

19.31.1.1 bricks of class Each 5 6117 30,585.00

designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes

with collars jointed with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement : 2 fine sand) including testing of joints

etc. complete :

For storm water pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse

sand : 10 graded stone aggregate 40 mm nominal size) up to

haunches of RCC. pipes including bed concrete as per standard design

a) 19.3.4 100 mm diameter S.W. pipe metre 500 458.5 2,29,250.00

b) 19.3.5 150 mm diameter S.W. pipe metre 50 743.1 37,155.00

TOTAL SEWER & STORM WORKS 12,66,959.50

Grand Total 22,07,518.75

Grand Total 22,07,518.75

Digitally signed by JAYA

DSR DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

Digitally signed by JAYA

Construction of Additional Girl's dormatory at JNV, Dist: Balasore, Bolangir, Mayurbhanj, Phulbani, Sambalpur

Sl. No. DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

H SUBHEAD OF BOREWELL

Boring/drilling bore well of required dia for casing/ strainer pipe,

by suitable method prescribed in IS: 2800 (part I), including collecting

samples from different strata, preparing and submitting strata

chart/ bore log, including hire & running charges of all

equipments, tools, plants & machineries required for the job, all

complete as per direction of Engineer -in-charge, up to 90 metre

1 23.1 ground level.

23.1.1 All Types of Soil

Boring/drilling bore well of required dia for casing/ strainer pipe,

by suitable method prescribed in IS: 2800 (part I), including collecting

samples from different strata, preparing and submitting strata

chart/ bore log, including hire & running charges of all

equipments, tools, plants & machineries required for the job, all

complete as per direction of Engineer -in-charge, beyond 90

metre & upto 150

2 23.2 metre depth below ground level.

23.2.1 All Types of Soil

Supplying, assembling, lowering and fixing in vertical position

in bore well, unplasticized PVC medium well casing (CM) pipe of

required dia, conforming to IS: 12818, including required hire and

labour charges, fittings & accessories etc. all complete, for all

3 23.3 depths, as per direction of Engineer -in-charge.

a) 23.3.3 200 mm nominal size dia Metre 240 1113.35 2,67,204.00

Supplying, assembling, lowering and fixing in vertical position

in bore well unplasticized PVC medium well screen (RMS) pipes

with ribs, conforming to IS: 12818, including hire & labour charges,

fittings & accessories etc. all complete, for

4 23.4 all depths, as per direction of Engineer-in-charge.

23.4.3 200 mm nominal size dia Metre 160 1255.70 2,00,912.00

Gravel packing in tubewell construction in accordance with IS:

4097, including providing gravel fine/ medium/ coarse, in

required grading & sizes as per actual requirement, all complete

5 23.8 as per direction of Engineer-in-charge. cum 28 2024.5 56,686.00

Development of tube well in accordance with IS : 2800 (part I)

and IS: 11189, to establish maximum rate of usable water yield

without sand content (beyond permissible limit), with required

capacity air compressor, running the compressor for required time

till well is fully developed, measuring yield of well by "V" notch

method or any other approved method, measuring static level &

draw down etc. by step draw down method, collecting water

samples & getting tested in approved laboratory, i/c disinfection

of tubewell, all complete, including hire & labour charges of air

compressor, tools & accessories etc., all as per requirement and

6 23.12 direction of Engineer-in-charge. Hr. 200 1085.05 2,17,010.00

Digitally signed by JAYA

Providing and fixing suitable size threaded mild steel cap or spot

welded plate to the top of bore well housing/ casing pipe,

removable as per requirement, all

7 23.13 complete for borewell of:

Providing and fixing M.S. clamp of required dia to the top of casing/

housing pipe of tubewell as per IS: 2800 (part I), including necessary

bolts & nuts of required size

8 23.14 complete.

Providing and fixing Bail plug/ Bottom plug of required dia to the

9 23.15 assembly of tubewell as per IS:2800 (part I).

Providing, laying, testing & commissioning of 'B' class heavy

duty G.I. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall/ceiling with suitable clamp/support frame

DSR-2022 and painting with two or more coats of synthetic enamel

10 E&M. 18.8 paint of required shade complete as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN

DSR-2022 1.6 rating with bronze/gunmetal seat duly ISI marked complete with

E&M- nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes

11 18.11 as required :

Providing, installation, testing and commissioning of non-return valve

DSR-2022 of following sizes confirming to IS: 5312 complete with rubber

E&M- gasket, GI bolts, nuts, washers

12 18.14 etc.as required :

Constructing masonry Chamber 60x60x75 cm inside, in brick work in

cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,

with C.I. surface box 100mm top diameter, 160 mm bottom

diameter and 180 mm deep ( inside) with chained lid and RCC top

slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate

20mm nominal size ) , i/c necessary excavation, foundation

concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate

40 mm nominal size) and inside plastering with cement mortar 1:3 (1

cement : 3 coarse sand) 12 mm thick, finished with a floating coat of

13 18.33 neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class

Supplying and drawing following sizes of FRLS PVC insulated

DSR-2022 copper conductor, single core cable in the existing surface/ recessed

14 E&M-1.17 steel/ PVC conduit as required.

Digitally signed by JAYA

Supplying & installation submersible pumping motor pumpsets ISI

marked of approved make. including starter, equivalent, making

connection suitable for tube- well/D.C.B. The job includes screwing

and welding of flanges on G.I. riser pipes installation, complete

fittings accessories with riser pipes jointing of electrical cables

other connections making switch board electrical connections, all

labour for testing of submersible pump and supply of water to

water mains complete in all respects, 7.5 H.P app. motor having

15 NON DSR discharging capacity 15 to 20 cum/hour against a head of 100 metres. Each 4 83487.00 3,33,948.00

Providing and fixing Panel Board compatible to submersible pump

with complete accessories like DOL starter, ammeter, voltmeter,

single phasing preventer and all motor protection arrangement,

earthing complete in all respect as per entire satisfaction and

16 NON DSR direction of Engineer-in-charge. Each 4 34786.00 1,39,144.00

ALL SUB-HEAD TOTAL 17,78,603 4,73,092

Sub TOTAL 22,51,695

Digitally signed by JAYA

Construction of Additional Girl's dormatory at JNV, Dist: Balasore, Bolangir, Mayurbhanj, Phulbani, Sambalpur

DSR DESCRIPTION Unit QTY. RATE DSR AMT. NSOR AMT.

SUBHEAD OF FIRE FIGHTING SYSTEM

1 Supply, Installation, Testing and Commissioning of

electric driven, centrifugal type, single/multistage, end

suction type, centrifugal pump of cast iron body, C.I

impallers with carbon steel shaft & mechanical seal

directely coupled with TEFC SQ cage foot mounted type

induction motors suiitable for operation on 3 phase, 415 volts

50 Hz AC with IP 55 Protection for enclosure, horizontall

foot mounted with class F insulation , complete in all

required or as directed by engineer incharge. 18.4.1 Each 5.00 101859.00 5,09,295.00

1.1 Terrace Booster Pump

2 Fabrication, Supplying, Installation, Testing &

Commissioning of electrical control panel of cubical

construction, wall mounted type, fabricated out of

2mm. thick CRCA sheet, compartmentalised with hinged

lockable doors, dust and vermin proof, powder coated of

approved shade after 7 tank treatment process, cable

alley, interconnection, and accessories mounting and

internal wiring, earth terminals, numbering etc. complete in

all respects, suitable for operation on 415 V, 3 phase 50 HZ

AC supply with enclosure protection class IP 42.

2.1 For Terrace Pump A7 Each 5.00 22180.00 1,10,900.00

3.1 Supply of following size of 1.1KV XLPE / PVC Insulated /

PVC sheathed (Heavy Duty) armoured electric cable with

aluminium conductor as per IS 7098 (Part-1) 1988 with upto mtrs 75.00 255.00 19,125.00

date Amendments. Make:- As per approved Make List (Make:-

Havell’s, RPG, RR Kabel,

3.2 Supplying and drawing following sizes of FRLS PVC

insulatedcopper conductor, single core cable in the existing 1.17.2 mtrs 75.00 70.00 5,250.00

surface/ recessed steel/ PVC conduit as required. 2 x 1.5 sq.

4 Providing and fixing IS marked butterfly valve (PN 1.6)

complete with companion flanges, bolts, 18.11

nuts, rubber insetions etc.

5 Providing and fixing check valve (NRV) complete with

companion flanges, bolts, nuts, rubber 18.14 0.00

6 Providing and fixing Strainer (Y-Type) complete with

companion flanges, bolts, nuts, rubber 18.15 0.00

7 Pressure Gauge Assemble with Gate/Ball Valve A6 Each 10.00 3990.00 39,900.00

8 Providing & fixing of pressure switch in M.S. pipe line

including connection etc. as required.

9 Air release Valve / Drain Valve A5 Each 10.00 24835.00 2,48,350.00

10 MS Structure support for piping A9 Kg 2500.00 65.00 1,62,500.00

11 Providing, laying, testing & commissioning of IS 1239

marked black M.S pipe including all fittings i.e bend,

elbows, tees, flanges, reducing socket, nuts and bolts,

gaskets etc fixed with welded / screwed joints. including

necessary excavation, backfilling, removal of surplus soil etc.

min. 1 mtr deep excavation and wrapping with

anticorrosive treatement with 4 mm thick asphalt tape as

per IS:10221, refilling the trench etc. OR fixed with screwed 0.00

or welded joints, hanged with clamps, hanger supports,

dash fasteners, bolts, nuts, rubber insertions etc

including threading, cutting, welding, edge preparation,

painting of approved colour over two coat of primer, cutting

& making good the wall/ floor wherever required, complete as

required or as directed by engineer incharge.

Digitally signed by JAYA

12 Providing and fixing S.S Fire Hydrant Valve of approved

quality with 63 mm female, instant, ovlique, single outlet, 80

mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank

cap and chain. conforming to IS: 5290 complete with 18.9.1 Each 10.00 7646.00 76,460.00

companion flange, bolts, nuts, rubber insertion / compressed

asbestos gasket etc. and painted in fire red colour.

13 Providing and fixing swinging, wall mounting type First Aid

Hose Reel of approved quality and made from compresed

steel sheet with dust cover, cast iron brackets including 30

m long, 19 mm nominal bore, high presure braided rubber

hose as per IS:444 Type hose guide, PVC shut off nozzle with

6 mm outlet and 25 mm nominal bore gun metal inlet 18.17.2 Each 10.00 12073.00 1,20,730.00

valve, bolts, nuts rubber insetion etc. painted in Fire red

colour including cutting and making good the walls

14 Providing and fixing 25 / 15 mm nominal gun metal gate valve

class I with CI wheel of approved A3 Each 10.00 1685.00 16,850.00

quality with union (Screwed end)

15 Providing and fixing in position 63 mm nominal bore and 15 m

long synthetic fibre, CP fire hose pipe of approved make

bearing IS: 636 -1988 type A mark and having TAC and MMD

approved with a pair of 63 x 63 mm gun metal 18.16.1 Each 10.00 5202.00 52,020.00

instantaneous type, heavy duty delivery hose coupling

(conforming to IS: 903) bound and riveted to the hose pipe

with copper rivets and copper wire complete.

16 Providing and fixing in position short SS brach pipe of

approved quality with 63 mm male 18.18.1 Each 10.00 2416.00 24,160.00

instatneous type inlet and 15 mm outlet nozzle complete

conforming to IS : 903

17 Supplying and fixing of hose cabinet of size 450mm x 450mm

x 250mm made of 2mm thick M.S. sheet with 6mm thick

glazed glass door including necessary locking arrangment

suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. A4 Each 5.00 10800.00 54,000.00

branch pipe mounted on wall or raised brick platform and

duly painted with post office red externally and white

internally with synthetic enamel paint complete in all respect.

18 Supplying, fixing, testing & commissioning of 1 set of 63mm

two way instantaneous fire brigade connection (FBC) with

inbuilt NRV comprising of SS and four SS instantaneous

male inlet coupling confirming to IS:604 with plug and cap 18.19.2 Each 5.00 13974.00 69,870.00

with chain as required with nut & bolts, washers, high

pressure gasket as required.

19 Supplying, fixing, Air Vessel of 250 mm dia and approx 1200

mm in length with air release valve and all accessories. 18.20 Each 5.00 18244.00 91,220.00

20 Providing , fixing Dry Chemical Powder (Stored Pressure

Type) Mono Ammonium Phosphate 50% powder

confirming to ‘IS 14609’ , Nitrogen Pressurized,

Controllable Discharge Mechanism, Pressure Gauge,

Discharge Hose & Nozzle Epoxy Polyester Powder Coated As A2 Each 40.00 3130.00 1,25,200.00

per ‘IS 15683’ ISI mark Fire Extinguishers. Operating

Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class

of FIRE complete in all respects (4 Kg Capacity)

ALL SUB-HEAD TOTAL 14,29,980.00 7,76,825.00

GRAND TOTAL 22,06,805

GRAND TOTAL 22,06,805

Digitally signed by JAYA