SPECIAL REPAIR TO BLDG NO T 39 OTM ACCN YOGENDER DIV, HARDING LINE OF DEMO TPS AT HQ JL WING THE INFRANTRY SCHOOL BELAGAVI UNDER GE BELGAUM

M&L for Cement concrete roofing tiles, rustic red colour, 420mm x 330mm size of 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry as in roofing, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after.

M&L for Cement concrete Rusted Red/Grey colour Ridge cap of size 360mmx207mm x 240mm, with and including 15mm thick in roofing bedded and jointed in cement mortar 1:6, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after.

S&F Mild Steel Corrugated Galvanised Steel Sheet 0.45mm thick of class 8, grade of zinc coating 275, as in roof covering with two corrugation side laps fixed with coach screws & washers, with and including dismantling u/s AC sheet roofing and removing rubbish off the premises, complete all as specified and as directed.

S&F Rolled mild steel roof trusses (framed) trussed purlins, rafters, struts (beam, tee, angle, channel, hollow sections or flat sections including wind ties, distance pieces, cleats etc. conforming to grade Fe 410-W Gde E - 250 quality 'B', complete all as specified and as directed.

M&L for PCC type C0 [1:3:6] using 12.50mm graded stone aggregate) as in copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, finished plain fair faces, including demolition of old cement concrete of any type, complete all as specified and as directed.

S&F Aluminium Composite Pannel board of 4mm thick, comprising of a core containing not less than 70% non combustible mineral filling, sandwiched between two skins of 0.50mm thick aluminium alloy PERALUMAN-100 of weight not less than 7.6kg/Sqm, with all sub structures, anchors, hardware and all fittings, fixed over and including aluminium section of size 35x25x2mm and 1.0m x 0.30m panel with and including necessary frame work, screwing & scaffolding, fixed with screws / nails, with and including dismantling existing u/s boarding of any description, complete all as specified. Note: Measurements shall be taken as flat as fixed without any allowance for laps.

M&L for Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for False ceiling with High Pressure Steam Cured (HPSC) 4mm thick Non Asbestos Fibre Cement ceiling boards fixed with and including supply & fixing powder coated aluminium snap grid of size 605mmx605mm consisting of 25X25X1.25mm aluminium angles and TEEs of size 35x25x1.25mm with galvanised wire of required length and 6mm dia hanger grid suspended from trusses/ ceiling and purlins not exceeding 1200mm c/c both ways, with and including applying three coats of white wash on ceiling surface, with and including taking down existing u/s ceiling with frame work of any description, complete all as specified and as directed.

M&L for Pre-cast cement concrete solid block masonary type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6, with and including demolition of existing brick work of any description, complete all as specified and as directed.

M&L for 10mm thick Rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finish the surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for 15mm thick Rendering on fair faces of brick work or concrete surfaces in two layers as 10mm thick in cement mortar 1:6 followed by 5mm thick in cement mortar 1:4 with and including mixed with M&L for water proofing compound @2% of weight of cement and finish the surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for Preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer with and including a coat of wall care putty, complete all as specified and as directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including preparation of new plastered surfaces of any description, all as per manufacturer's instructions, complete all as specified and as directed.

M&L for complete removal of existing treatment on old walls with wire brush, scrapping down smoke soot, mould, moss and efflorescent salts, oils & greasy spots etc., and two coats of oil bound distemper over a coat of alkali resistant primer with and including a coat of wall care putty and preparation of old surfaces of any description, complete all as specified and as directed.

M&L for complete removal of existing treatment on old walls with wire brush, scrapping down smoke soot, mould, moss nad efforescent salts, oils & greasy spots etc., and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including preparation of old surfaces of any description, complete all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C1 (using 20mm graded hard granite stone aggregate) as in plinth protection, finished even and fair without using extra cement including making construction joints in 3 mtres interval and joint filled with sealing compound, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area n. exc. 1.5sqm each, complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area exc 1.5sqm but n. exc. 4.0 sqm each, complete all as specified and as directed.

M&L for Second class hard wood plain solid straight chowkhat and frames, wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints, complete all as specified and as directed.

M&L for Factory made 2nd class hard wood plain, framed, panelled door shutter 35mm thick, two panels with lock rail and panels of 12mm thick plywood BWR 9 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24(a) and fitted to Chowkats, complete all as specified and as directed.

M&L for Factory made 2nd class hard wood Glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. (with divided in to square with plain, chamfered or rounded, mitered and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); supplied and fitted to chowkats, complete all as specified and as directed.

M&L for Factory made 2nd class hardwood 30mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc for windows, ventilators for etc provided with stiles and rails and divided into square with plain chamfered or rounded mitred and rebated sash bars any numbers size of members of shutters as specified in SSR Part-I Section 8 Clause 8.24(b) supplied and fitted to chowkats, complete all as specified and as directed.

M&L for Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for Preparing old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tack or stainless wire staples, complete all as specified and as directed.

S&F IN REPAIR Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tack or stainless wire staples, complete all as specified and as directed.

S&F MS butt hinges cold rolled medium weight 100mm size, ISI marked, complete all as specified and as directed.

S&F MS butt hinges cold rolled medium weight 75mm size, ISI marked, complete all as specified and as directed.

S&F IN REPAIR Mild Steel Helical Door Spring 300mm long rat tail pattern with and including roller and roller plate, complete all as specified.

S&F 100mm long extruded section aluminium alloy anodised handles fabricated type, complete all as specified and as directed.

S&F 150mm long extruded section aluminium alloy anodised handles fabricated type, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt of extruded section of size 100mm long complete, complete all as specified and as directed.

S&F Aluminium anodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified and all as directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane, with and including hacking out old broken glass (any thickness/size, quality or description) from wooden frames, glazed with putty or fixed with beads, complete all as specified and as directed.

M&L for Point wiring with 1.5 Sq.mm FRLSH PVC insulated unsheathed copper conductor cable, single core multi stranded 1100Volt grade conforming to IS 694: 1977, drawn in and including PVC casing & caping of suitable size, ISI marked, with accessories, junction boxes, tees, terminal boxes, factory made PVC surfaces boxes with modular top cover plates with frame for switches / sockets etc., including one run of 1.5 Sq.mm single core FRLS PVC unsheathed copper conductor cable as earth continuity conductor and connected to common earth dolly, for one light / fan /bell point controlled by one way switch/MCB, including taking down old u/s point wiring of any type with fittings, complete all as specified and as directed. Note: Cutting chases and making good surfaces shall be included in the unit rate.

All as per Serial Item No. 36 here-in-before but for 3 pin 5/6Amp switch socket point, on same board, complete all as specified.

All as per Serial Item No.36 here-in-before but for 3 pin 5/6Amp switch socket point, on independent board, complete all as specified.

All as per Serial Item No. 36 here-in-before but with 2.5Sqmm copper conductor cable and 2.5 Sqmm cable as earth continuity conductor for 3 pin 6/16Amp switch socket point, on independent board, complete all as specified.

S&F Modular switch 1 way 5/6Amp, 1 Module, 240 Volts, complete all as specified and as directed.

S&F Modular Socket, 5/6A, 2/3 pin combined , 2 module, 240 Volts, complete all as specified and as directed.

S&F Modular switch 1 way 15/16A, 1 Module, 240 Volts, complete all as specified and as directed.

S&F Modular Socket, 6A/16A, 2/3 pin combined multipurpose, 2 module, 240 Volts, complete all as specified and as directed.

S&F Modular BLDC Fan regulator, 240Volt, electronic step type, 2 Module, suitable for BLDC ceiling fan of any sweep, complete all as specified.

S&F Ceiling rose, 3 terminals PVC/Polycarbonate, 3 phase, isolated body, complete all as specified and as directed.

S&F IN REPAIR LED Professional Luminaries batten type fitting warm / cool white 1X20watt, 220Volt, not less than 120lum/Watt, color temp 3000 - 5000k, PF>0.95, AC, indoor aluminium housing LED battens, integrated type batten with THD<10% with polycarbonate diffuser, with and including all accessories, pre-wired and connecting up with three core flexible copper conductor cable of suitable size, complete all as specified.

S&F IN REPAIR LED Professional Luminaries, Inverter type LED integrated batten fitting 1X20watt, with square profile & polycarbonated channel, lithium ion battery with charging time 8 to 10 hours and backup time upto 4 hours complete with all accessories, 220Volt, not less than 120lum/Watt, color temp 3000 - 5000k, PF>0.95, AC, with driver and LED tube light and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified. Make: Cat Part No. LHEXACP7FN1W020 of Havells or Equivalent make as specified here -in-after.

S&F IN REPAIR LED Professional luminaires 600mm x 600mm, 35/36 watt type fitting warm / cool white, 220Volt, not less than 120lum/Watt, color temp 3000 - 5000k, PF>0.95, AC recessed type with high efficiency PMMA diffuser soft glare free light, complete with driver and connecting up with three core flexible copper conductor cable of suitable size, complete all as specified.

S&F IN REPAIR LED Building Security light fitting 35Watts, 230 volts, not less than 120lum/Watt, color temp 3000 - 5000k, with Suitable size GI bracket made out of 32mm GI light grade pipe fixed with clamps, nuts & bolts etc., with IP 65/66 protection pressure die cast aluminium housing and heat resistant complete with driver, bracket with impact, corrosion resistant and all accessories, complete all as specified and as directed.

S&F Modular Bell push, 5Amp, 230Volt, 1 Module, complete all as specified.

S&F Ding Dong type Calling Bell, 230Volt, AC, complete all as specified.

S&F IN REPAIR factory made epoxy powder coated distribution board double door TPN 4 ways (VTPN DB 415Volt) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts and suitable for MCCB as incomer, MCBs as outgoings, complete all as specified.

S&F IN REPAIR MCCB, 4pole, 125 Amps, 415Volts, thermal magnetic, Ics=100% Icu, 16kA current rating conforming to IEC-60947-II along with spreader incl Phase Barreir to be fixed in distribution board, complete all as specified.

S&F IN REPAIR, Factory made epoxy powder coated sheet metal enclosure for DBs (Fixed flush to the wall), SPN, 230volt, 12Way, double door, IP-42 protection with 200 Amp rated copper bus bar 230Volt, complete all as specified.

S&F IN REPAIR MCB SPN 40Amp, 10kA, 230Volt, B curve with necessary connecting up in MCB DB, testing and commissioning, complete all as specified and as directed.

S&F IN REPAIR MCB SP 16 to 32Amp, 10kA, 230Volt, B curve with necessary connecting up in MCB DB, testing and commissioning, complete all as specified and as directed.

S&F IN REPAIR GI pipe light grade pipe 40mm dia for cable protection, complete on pole/walls/in road etc for cable protection, complete all as specified.

M&L for Circuit / Sub main wiring with Two runs of 6.0Sqmm PVC FRLSH insulated copper conductor cable, single core multi stranded 1100Volt along with one run of 6.0Sqmm as earth wire, with and including drawn through concealed / surface rigid PVC conduit of 25mm size with accessories, including taking down old submain wiring of any type, complete all as specified and as directed. Note: Two runs of cable, one run of earth wire and one run of casing & capping shall be measured as one unit.

M&L for IN REPAIR Earthing complete with galvanised steel earth plate electrode 60cm X 60cm X 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead 4mm GI wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of SSR Part-I, including excavation / earth work in any strata, adequate quantity of charcoal and common salt, PCC chamber with RCC 1:2:4 type B1 40mm thick cover slab with 8mm dia TMT bars @150mm c/c in bothways, suitable handle and angle iron frame of suitable size to fix the cover, with 20mm bore GI pipe light grade for watering with funnel, wire mesh and 15mm bore GI pipe medium grade for GI wire protection and 4mm GI earth wire, including testing after completion, complete all as specified and directed. Note : Earth wire will be measured after 7.5mtr from the earth strip or earth testing terminal block whichever is lesser under relevant item.