Supply and installation of Furniture including modular science labs Physics Chemistry Biology and Computer sc 1412093 Nithari SKV SH Civil and Furniture Works.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size (i.e 300x450 mm /300x600 mm/600x1200mm or more size etc.)as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing partition upto ceiling height consisting of G.l. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.l. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: (part 3) (Board with BIS certification marks)

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes/ soil waste pipe conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes/soil waste pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110mm

Single tee with door 110x110x110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour Two coats

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metreslead : Of area 3 sq. metres and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 20 mm nominal bore

Less DSR 2023 correction factor i.e. (1-0.973) on existing items of the DSR-2023 (i.e. item no. 01 to 20)

Deduct for Cost Index on DSR 2023 @ 0.09%

Credit for taking away the dismantled door shutter items etc. material received from site by execution of dismantaling/ demolishing various items stacked at site band measured, which will be property of contractor duly weighed / measured before removing from the site in the presence of E-in-c or his authorised representative all complete.

Credit for taking away the dismantled steel / G.I. items etc. material received from site by execution of dismantaling / demolishing various items stacked at site band measured, which will be property of contractor duly weighed / measured before removing from the site in the presence of E-in-c or his authorised representative all complete

Work Tables – One Way Gas Valves Providing and fixing laboratory grade 1 Way LPG Gas Valve made from high quality brass forging grade as per IS 8737 2007 and machining grade as per IS:319 to avoid porosity and leakage. Taps are powder coated with glossy epoxy fusion bond. Pneumatic test at 250psi, hydraulic test at 125 psi, bursting test at 500psi. Valves should be identified with service indexes in the color coding as per DIN 12920. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge.

Work Tables – Two Way Gas Valves Providing and fixing laboratory grade 2 Way LPG Gas Valve made from high quality brass forging grade as per IS 8737 2007 and machining grade as per IS:319 to avoid porosity and leakage. Taps are powder coated with glossy epoxy fusion bond. Pneumatic test at 250psi, hydraulic test at 125 psi, bursting test at 500psi. Valves should be identified with service indexes in the color coding as per DIN 12920. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge.

Work Tables - Electrical Trunking Providing, placing/installing of Electrical trunking manufactured to the specification provided below - size 220mm(L) x 86mm(D) x 90mm(H) including 6 Module Plate with 16A, 1 Way electrical switches & 6/16A, 6 Pin Shutter Sockets, Electrical Wire (2.5mm), Drilling of 2Nos x 12mm Holes & 1No x 25mm Holes on Granite Top for fixing and passage of wires with necessary fittings on the existing Lab Benches Granite Tops as per the site requirement. Electrical wires shall be covered with Flexible Pipe below the Table Top till the length of the Table. Trunking top panel, bottom panel and body should be made from minimum of 0.8mm thick CRCA MS sheet with pure epoxy powder coating of 40-45 microns. The front surface that houses the electrical points should have a slope. Electrical wire should be connected in series with the adjacent Trunking upto the source within the Table Length. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge.

Laboratory Tables - Reagent Racks Providing, placing/installing of Laboratory Tables Reagent Racks manufactured to the specification provided below - size 1200mm(L) x 300mm(W) x 680mm(H):- Reagent Racks shall be complete modular design consisting of 2 stage horizontal storage shelves made of 1.6 mm thick frame. Shelf : Fixed-Type reagent shelves have 1.6mm thickness consisting of 2 stage horizontal storage shelves made of 1.6 mm thick frame of CRCA MS sheet with epoxy powder coating and shall have 4 nos. plates (containing 03 module each) for electrical switches and sockets including necessary wiring etc. It shall have provision for placing Granite pieces. Cutout for 3 module plate to be provided. All the members are knock down and can be restructured. The metal part cutout shall be of 1.00mm thickness. The finish shall be coating of 40-60micron thickness. Load carrying capacity of 70kg for Island table. All the above items shall be as per photo, sketch specifications & direction of engineer-in-charge.

Laboratory Work Bench - Sink Unit Providing, placing/installing of Sink Unit manufactured to the specification provided below - size 600mm(W) which shall comprises of Sink Cabinet, Polypropylene Sink Unit and 1-Way Goose Neck 360 Degree revolving Faucet.as per following Sink Cabinet Sink cabinet. :- The Sink cabinet shall be Welded body with load bearing members such as top, bottom and stiffeners made of 0.8mm thick CRCA Sheet. The cabinet unit shall be provided with Pair of Shutters. Shutter has a sandwich construction with profile as a sound dampener. The complete unit shall be epoxy powder coated with thickness of 40-60 microns and is suspended from tubular understructure, with an overlay shutter. The cabinet has a corrosion resistance magnetic strip as shutter catch. Shutter shall be provided with semi recessed handle and five knuckle overlay hinge (SS-304) with 270degree opening. Cabinet fixing brackets of 2mm thickness. The cost of sink cabinet does not includes the cost of basic understructure as the cost of understructure shall be paid in Item No 1. All the above items shall be as per photo, sketch specifications & direction of engineer-in-charge. b. Polypropylene Sink Assembly Providing and fixing Polypropylene Sink with PP Waste, Anti-Siphon Bottle Trap & Flexible Drainage Pipe. Sink bowl shall be Polypropylene Molded made up of 5mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size shall 600mm(L) x 400mm(W) x 300mm(D). c. 1Way Water Faucet Providing and fixing 1-Way 360 Degree Revolving Water Faucet. Faucet fittings shall be laboratory grade. Water faucet and valve bodies shall be cast red brass alloy or bronze forgings, all fittings shall be powder plated. Brass as per IS:319, Pipe as per : IS:407,O utlet nipple in PP construction. PP knob to be used. All gasket and O-ring of Nitrile Rubber make. Inlet connection 1/2" BSP. Gooseneck spout with 360 degree rotation with 500000 life cycles. Pneumatic test at 250 psi, hydraulic test at 125 psi, bursting test at 500 psi. Coating to be glossy epoxy fusion bond. The Faucet shall be fixed to the existing water outlet by providing PVC connection with brass unions of required length. All the above items shall be as per photo, sketch specifications & direction of engineer-in-charge.

Work bench Storage Cabinets Providing, placing/installing of work bench Storage Cabinets manufactured to the specification provided below - The storage cabinet shall be Welded body with load bearing members such as top, bottom and stiffeners made of 0.8mm thick CRCA Sheet. A drawer separator shall be provided made of 1.2mm thick CRCA sheet. The storage unit shall be provided with a shelf made of 0.8mm thick CRCA sheet which is adjustable to 6 slots of 40-60mm. Each shelf shall have load carrying capacity of 40 kgs. Shutter providedis over-closing with 270degree opening. It has a sandwich construction with profile as a sound dampener. The drawer shall be provided as per the manufacturers specifications and direction of Engineer -in-Charge. The complete storage unit shall be powder coated with thickness of 40-60 microns and is suspended from tubular understructure, with an overlay shutter. The cabinet has a corrosion resistance magnetic strip as shutter catch, shutter and drawer are equipped with 180 degree cam lock. Semi recessed handle and five knuckle overlay hinge(SS-304) with 270 degree opening. Drawer and Shutter shall be provided with a lock 180 Degree cam with 4mm thick lever. Cabinet fixing brackets shall be of 2mm thickness. Note:- The cost of storage cabinet does not includes the cost of basic understructure, the cost of understructure shall be paid in Item No 1. (All the above items shall be as per photo, sketch specifications & direction of engineer-in-charge.) b. Storage unit of Size 450mm(W) x 450mm(D) x 675mm(H) with 1 Drawer and 1 Shutter

Work bench Storage Cabinets Providing, placing/installing of work bench Storage Cabinets manufactured to the specification provided below - The storage cabinet shall be Welded body with load bearing members such as top, bottom and stiffeners made of 0.8mm thick CRCA Sheet. A drawer separator shall be provided made of 1.2mm thick CRCA sheet. The storage unit shall be provided with a shelf made of 0.8mm thick CRCA sheet which is adjustable to 6 slots of 40-60mm. Each shelf shall have load carrying capacity of 40 kgs. Shutter provided is over-closing with 270 degree opening. It has a sandwich construction with profile as a sound dampener. The drawer shall be provided as per the manufacturers specifications and direction of Engineer -in-Charge. The complete storage unit shall be powder coated with thickness of 40-60 microns and is suspended from tubular understructure, with an overlay shutter. The cabinet has a corrosion resistance magnetic strip as shutter catch, shutter and drawer are equipped with 180 degree cam lock. Semi recessed handle and five knuckle overlay hinge(SS-304) with 270 degree opening. Drawer and Shutter shall be provided with a lock 180 Degree cam with 4mm thick lever. Cabinet fixing brackets shall be of 2mm thickness. Note:- The cost of storage cabinet does not includes the cost of basic understructure, the cost of understructure shall be paid in Item No 1. (All the above items shall be as per photo, sketch specifications & direction of engineer-in-charge.) a. Storage unit of Size 600mm(W) x 450mm(D) x 675mm(H) with 1 Drawer and 2 Shutters

Laboratory Work Bench - Understructure Providing, placing/installing of Laboratory work bench Understructure manufactured to the specification provided below - D-Frames Assembly, Horizontal members with Granite Top and Cover Panels. These understructures shall be of 750mm or 900mm height as per site requirement or as per the direction of Engineer-in-Charge. The Top surface area of under structure shall be measured for payment. The understructure shall comprises of following components :- a. D-Frame Assembly All D-Frames assemblies shall be manufactured from standard hollow metal sections; confirming to latest I.S. Code 7138 (Indian Standard specification for steel tubes for furniture) and all sheet metal components shall be of CRCA confirming to latest IS Code 513. The dimensions of D Frame shall depend upon the depth of the understructure. The overall depth (F) of D-Frame shall be 705mm for 750mm Depth Structure and 555mm for 600mm depth (as per Drawing) and Depth of Extended Frame (G) shall be 235 mm for 750mm Depth and 160mm for 600mm depth (as per drawing). All frame-work shall be pre-treated with superior powder coated finish with 40-60 micron thickness. The structure of D-frame with horizontal units shall withstand 10 degree tilt (backwards) without toppling. The D-Frames shall have a provision to fix suspended storage cabinets. Side frame shall be of welded MS ERW tube of dimension 30 x 30 x 1.6mm thickness. Bracket for pipe : MS CRCA 2mm thick. Wall bracket : MS CRCA 2mm thick. Levelling screws: 4 nos. of M-10 levellers (MS + Nylon) Adjustments possible with range 20mm. Anchoring bolt of Hilti make or equivalent. b.HorizontalMembersHorizontal members shall join two D-Frames to form the structure. Horizontal members shall be made from rectangular pipes of 1.6mm thickness. Cross-sectional dimensions of the pipe shall be 30 x 30mm with a minimum of 1.6 mm thickness. They shall be made of CRCA MS sheet powder coated of 40-60 micron thickness. Horizontal members connect two D-Frames together by using C-clamps/U-clamps together with the D-Frames and Horizontal Members . The skeletal structure of the work-bench is formed on which the worktop shall be placed and the hanging-type storage cabinets shall be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They shall be available in various widths of 450mm, 600mm, 900mm, 1050mm, 1200mm, 1350mm, 1500mm, 1650mm and 1800mm (Tolerance +/- 10mm). These horizontal units together constitute a table set. c. Cover Panels All side cover panels and back panels, filler panels shall be made from CRCA MS panels of minimum 0.8mm thickness with epoxy powder coating with thickness of 40-60 microns, bracket of min.1.2mm thickness. d. Work Top The complete structure shall be provided with a Worktop of 20mm (+/- 2mm) thick Jet Black Granite. The exposed edges of the worktop shall be chamfered and polished . The bottom of cantilever portion of the worktop shall be polished and V-groove shall be provided throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material shall be neoprene mat of 6 mm thickness. All the above items shall be as per photo, sketch specifications & direction of engineer-in-charge.

Office Almirah Providing, placing/installing of Office Almirah manufactured to the specification provided below - The overall size of the storage shall be 910-916mm (W) x480 -486mm (D) x 1980-1981mm (H). The contruction shall be welded/rivetted construction with 0.8 mm thick CRCA for shelf and 0.8mm thick for back. The door shall be made of 0.8mm thick CRCA sheet with having minimum 3 hinges on each door in almirah and all other metal component shall be made of 0.8mm thick CRCA. Stiffners shall be provided from top to bottom in the almirah to prevent any deflection/deformations on the outer body. A locker shall be provided inside the almirah of size 400mm(W)X300mm(H) with locks & door fixed on hinges .The locking and handle of the storage shall be mazak handle with three way locking mechanism and thickness of rod shall not be less than 8 mm. The Alimrah should have 2 welded Legs along the depth of the Almirah of 75mm Width x 125mm Height made up of 1mm thick galvanized sheet which acts as a understructure of the storage. The shelving shall be height adjustable with slots of pitch 25.4mm from top to bottom at all internal corners and shall have a load capacity of 40kg. The product shall be epoxy powder coated to the thickness of 50 microns. All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge.

Lab Stools Providing, placing/installing of Lab Stools manufactured to the specification provided below - With SS Round Top. Overall size is 480mm(L) x 480mm(W) x 560mm(H). Understructure of the stool consists of 4 Legs, circular Foot Step welded at 150mm above from ground and Top Frame. Complete understructure shall be made up of MS ERW Tube of 22mm Dia having a thickness of 1.6mm with duly powder coated 40-45microns. A Round Top of size 300+/-5mm Dia shall be fixed on the top frame made of 1mm Thick Stainless Steel (SS) with buffed Glossy finish. PVC Shoes shall be provided at the bottom of all legs to avoide direct contact of metal parts with floor. Stool shall be safe upto 120Kgs Load. All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge.

Computer Chairs Providing, placing/installing of Computer Chair manufactured to the specification provided below- The seat and back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The Seat is provided with a pre-moulded inserts at the bottom for fixing Mechnism and Armrests. The back foam is designed with contoured lumbar support for extra comfort. BACK) SIZE: 40.0cm. (W) X 47.0cm. (H) SEAT SIZE: 45.0cm. (W) X 42.0cm. (D). The HR Polyurethane foam is moulded with density=45+/-2 kg/m cube and hardness load 16+/-2 kgf as per IS:7888 for 25% compression. The one piece armrests are injection moulded from black nylon. The armrests are fitted to the seat with armrest connecting brackets made of 0.5cm. thk. HR steel. The permanent contact mechanism is designed with 360°revolving type. 14° maximum back-tilt only.Upright position locking. Tilt tension adjustment. The pneumatic height adjustment has an adjustment stroke of 11.0 cm.The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 62.0cm. pitch-center dia. (72.0 cm with castors).The twin wheel castors are injection moulded in Black Nylon. All the above items should be as per photo, sketch , specifications & direction of engineer-in-charge.

Teacher Chairs Providing, placing/installing of Teacher Chair manufactured to the specification provided below - The Seat and Back Assembly shall be made up of 1.2cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The Seat is provided with a pre-moulded inserts at the bottom for fixing Armrests. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE : 47.5cm(W) x 58.0cm(H) and SEAT SIZE : 47.0cm(W) x 48.0cm(D). The Polyurethane foam is moulded with density = 45 +/-2 kg/m 3 and Hardness = 20 +/- 2 at 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated tubular frame is cantilever type & made of dia 25.4mm x 2mm thick M.S. ER.W. Tube as per sketch for item. All the above items should be as per photo, sketch ,specifications& direction of Engineer-in-Charge.

Computer Tables Providing, placing/installing of Computer Table manufactured to the specification provided below - Overall dimension 900mm(W) x 550mm(D) x 740mm(H). The base material for computer table should be 18 mm thick Lami ply, MR Grade as per IS:303 with decorative lamination (0.8 mm thick) on both sides with 2mm lipping. It should provides higher resistance to heat and moisture. The understructure of the Table should be Fabricated component from 38mm x 25mm x 1.2mm thick MS ERW Tube (IS:4923) with Powder coat to the thickness of 40-50microns . The Table should be provided with a lamiply Keyboard Tray. Single Drawer is provided on the right side of the table of size 150mm(L) x 300mm(D) x 100mm(H) with lamiply facia and telescopic channels. A Shelf is provided of size 600mm(L) x 200mm(D) for keeping files. A CPU stand is in built in the understructure of size 200mm(W) x 500mm(D) and one additional support of 38mm x 25mm x 1.2mm thick MS ERW Tube (IS:4923) with Powder coat to the thickness of 40-50 microns is provided at the bottom .All the above items should be as per photo, sketch, specifications & direction of engineer-in-charge.

Teachers Table Providing, placing/installing of Teacher Table manufactured to the specification provided below - Size 1200mm(L) x 600mm(D) x 725mm(H). Worksurface of the table shall be made from 18mm thick Pre Laminated wooden Ply (Lami Ply, MR grade as per IS:303) with decorative lamination(0.8mm thick) on both sides for top. All work surface edges are duly sealed with 2mm thick PVC edging of matching colour with hot melt glue at 200°C. Understructure of the table comprises Rectangular Frames Fabricated from 1.2mm thick Cold Rolled Close Annealed (IS:513), Finish of metal parts - Powder coat (Epoxy polyester). Leg and one foot rest between the base and vertical wire carrier should be Fabricated component from 38mm x 25mm x 1.2mm thick MS ERW Tube (IS:7138) with Powder coat (Epoxy polyester). Modesty panel shall be 0.8mm Thick CRCA Sheet duly poweder coated. One Side Panel made from 0.8mm thick CRCA (IS:513). Wire Carrier shall be provided, Vertical Wire Carrier along with Drawer made of 0.8mm Thick CRCA Grade D as per IS:513 and Horizontal Wire carrier under the worktop made of 0.8mm thick CRCA Grade D as per IS:513 complete powder coated. Finish: Powder coat (Epoxy polyester), Plastic Cap for Cable travel should be Injection Moulded Polypropylene. Leveler glide for Leg of Nylon 6 & MS Bolt. Drawer Unit with 3 Drawers shall be provided of size 670mm(H) X 550mm(D) X 350mm(W), Shell, drawer tray, Drawer Front, Frame Assembly of the drawer unit shall be made of 0.8mm thick CRCA (IS:513) with Powder coat (Epoxy polyester). 10 lever cam Lock shall be provided for locking. Handle shall be made from Injection Moulded Polypropylene & Leveler of Nylon6 & MS Bolt. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge.