SOPD_SIG_20_21_23 Strengthening and Widening of Kalajal Balahati road under Signature Project under SOPD-G for the year 2020-21, Mangaldai HPC (Kamalpur LAC)

Amount

Clearing and Grubbing road land including uprooting rank vegetation grass bushes shrubs sampling and trees girth up to 300mm removal stumps of trees cut earlier and disposal of unerviceable materials and staking of serviseable materials to be use or acutioned up to a lead of 1000m including removal and disposal of top orgenic soil not exceeding 150mm in thickness as per MORTH specification 201. i) By Manual Means (A) In area light jungle.

Scarifying Existing Bituminous Surface to a Depth of 150 mm by Mechanical Means Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

Construction of Embankment with materials obtained from borrow pits, with a lift up to 1.5 m. transporting to site, speeding, grading to required slope and compacting to meet requirement of table 300.1 and 300.2 with a lead upto 1000 m. as per technical specification clause 301.5. (a) from private land

Construction of sub-grade and earthen shoulders with approved materials obtained from borrow pits, with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m. as per technical specification clause 303.1 (a) from private land

Excavation in Cutting in Soil by manual means with lead upto 50 m Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3 (Manual should be use where machines cannot be deployed due to site condition)

Construction of granular sub-base by providing well graded meterials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieved the desired density, complete as per technical specification clause 401 . (i) for grading ii material

Water Bound Macadam Sub- base/ base (only for (PMGSY work) 2) WBM Grading 2 Using stone screening Type - B 11.2 mm for Gr 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100kN in stages to proper grade and camber, applying and brooming,stone screening/ binding materials to fill - up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405 (A) By Manual means

Water Bound Macadam Sub- base/ base (only for (PMGSY work) WBM Grading 3 Using stone screening Type - A 13.2 mm for Gr 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100kN in stages to proper grade and camber, applying and brooming,stone screening to fill - up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405 (A) By Manual means

Prime Coat Medium porosity Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502.

Tack Coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Dense Graded Bituminous Macadam (Providing and laying dense bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5% by weight of total mix and filler transporting the hot miox to work site,laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no. 507. complete in all respect. (including carriage of mixed materials up to 10.0 Km initial lead from mixing plant )( Including cost of testing of materials at site and laboratory as directed by the deptt.) (a) With hydrated lime/cement as filler (refer table 500-9 of MoSRT&H specification) (A) with 60/70 or VG-30 grade bitumen (ii) for GradingII(19 mm nominal size)

Bituminous Concrete (Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 % of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.509. complete in all respect. (including carriage of mixed materials up to 10.0 Km initial lead from mixing plant ) (Including cost of testing of materials at site and laboratory as directed by the deptt.) A With hydrated lime/cement as filler ( refer table 500-9 of MoSRT&H specification) I with 60/70 or VG-30 grade bitumen (ii) for Grading-II(13 mm nominal size)

Inter locking concrete Block pavement I)a Providing and laying interlocking concrete block pavement (M40) having thickness 80mm as per technical specification clause 1504 (inclusive of Edge restraint and carriage)

Direction and Place Identification signs upto 0.9 sqm size board A. Retro-reflectorised Traffic Signs (1) Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Retro-reflectorised Traffic Signs Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 (I) 90 cm equilateral tringle

Painting lines, dashes, arrows, etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and Technical Specification Clause 1702

Road Markers/Road Stud with Lens Reflector Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973.

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 ii)Ordinary Kilometer Stone (Precast)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 iii)200 m stone (precast)

Construction of Speed Breaker WBM Grading 3 Using stone screening Type-B 11.2 mm for Gr.III Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. (A) By Manual Means

Built-Up Spray Grout Providing, laying and rolling of built-up spray grout layer over prepared base consisting of a two layer composite construction of crushed coarse aggregates using motor grader for aggregates. Key stone chips spreader may be used with application of bituminous binder after each layer, and with key aggregates placed on top of the second layer to serve as a base, conforming to the line, grades and cross-section specified, the compacted layer thickness being 75 mm as per Technical Specification Clause 505. (A) By Manual Means ii. Bitumen (S-90)

Tack Coat ii) Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. Case - I By Manual Means i) Bitumen (S-90)

Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 A) By Manual Means Case - I : Type A i) Bitumen (S-90)

Painting lines dashes , arrows etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS : 164n bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter demarkation at the site and traffic control as per drawing and echnical specification clause 1702

Providing and fixing of road stud 100mm x 100mm dia cast in aluminium , resistant to corrosive effect of salt and grit, fitted with lens reflectors, installed in concrete or asphaltic surface by drilling holes 30mm up to adepth of 600mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS: 873 (Part 4) 1973.

Providing and fixing of rectro- reflectorised cautionery mandatory and informatory sign as per IRC 67 made of encapsulated lens type reflecting sheeting vide clause 1701.2.3 fixed over aluminium sheeting 1.5 mm thick supproted on mild steel iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 gade cement concrete 450mm x 450mm x 6mm, 600mm below the ground level as per drawing and Technical specification clause 801 '(ii) 60cm equilateral triange

Providing and fixing of rectro- reflectorised cautionery mandatory and informatory sign as per IRC 67 made of encapsulated lens type reflecting sheeting vide clause 1701.2.3 fixed over aluminium sheeting 1.5 mm thick supproted on mild steel iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 gade cement concrete 450mm x 450mm x 6mm, 600mm below the ground level as per drawing and Technical specification clause 801 '(iii) 60cm circular

Providing and fixing of rectro- reflectorised cautionery mandatory and informatory sign as per IRC 67 made of encapsulated lens type reflecting sheeting vide clause 1701.2.3 fixed over aluminium sheeting 1.5 mm thick supproted on mild steel iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 gade cement concrete 450mm x 450mm x 6mm, 600mm below the ground level as per drawing and Technical specification clause 801 (iv) 80cm x 60cm rectangular

Guard Posts Supplying, fitting and fixing RCC guard post 150cm long erected 75cm above the ground and 75cm below the ground with M-15 grade (nominal mix 1:2:4 with broken stone aggregate up to 20mm size) of cement concrete and required reinforcement tied in position with annealed black wire including centering, moulding the top, curing including painting concrete surfaces in 23cm strips upto 0.75m from the top alternately in black and white and having 2 nos. reflective band of desired shade etc. complete as per design and as directed. (B) 15 cm dia. RCC guard post with reinforcement of 4nos. 12mm dia TMT main steel bars and 6mm TMT/ MS stirrups at 15cm c/c.

Planting of Trees and their Maintenance for three Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for three year.

Half brick circular tree guard internal diametre 1.25 m and height 1.2 m above ground and 0.02 m below ground bottom two coarses laid dry and top three coarses in cement mortar 1:6 and the intermediate coarses being in dry honey comb masonry as per design complete.

RCC Drain with Cover Slab Excavation for Structures Earthwork in excavation for foundation of structure as per drawings and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and back filling with approved material. I) Ordinary Soil. A. Manual Mean i) Depth up to 3 m

Brick Soling Laying brick soling layer on prepared sub- grade with brick on end edging according to lines, graded and cross- section shown on the drawing filling joints with sand and earth , spreading 25mm thick layer of earth soling watering and rolling the same with three road roller 80-100 kN as per Technical Specification clause 412

Providing concrete for plain / reinforced concrete in open foundations complete as per drawings and technical specification clause 802,803,1202 & 1203. A. With crushed stone I PCC grade M10 Nominal mix 1:3:6

Providing concrete for plain / reinforced concrete in open foundations complete as per drawings and technical specification clause 802,803,1202 & 1203. A. With crushed stone IV RCC grade M20

Supplying, fitting and placing TMT (Fe 500) bar reinforcement in foundation complete as per drawings and Technical Specifications clauses 1000 and 1202.

RCC Slab Culvert (4.00 m span) Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. I. Ordinary soil Upto 3 m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 A. With crushed stone. I. P.C.C grade M 10 Nominal mix 1:3:6

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 B. With Natural Gravel III. P.C.C Grade M 20 Nominal mix 1:2:4

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 A. With crushed stone I. R.C.C grade M 20 (I) For nominal mix 1:2:4 a} Height upto 5 M

Drainage spouts complete as per drawing and technical specifications Clause 1209

Filler Joint Iv} Providing and filling joint sealing compound as per drawings and technical specifications with coarse sand and 6 per cent bitumen by weight.

Supplying, fitting, and placing TMT bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 A. With crushed stone

Construction of R.C.C. railing of M 25 grade in cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500, centre-to-centre spacing between vertical posts not to exceed 2000 mm as per drawing and technical specifications Clauses 800, 900 and 1208.3

ARIFUDDIN AHMED

LAJIK BRAHMA