SPECIAL REPAIR TO BLDG NO P-152 OR TOILET AND BATHROOM BLOCK IN BHARATPUR LINE AND CERTAIN OTHER MINOR REVENUE WORKS IN TIRAH LINE AT MIL STN DHARAMSHALA

Amount

Sch 'A' Part-I: Special Repair to Bldg No P-152 ( OR's Toilet & Bathroom block) in Bharatpur Line. Taking down chowkhats or frames with shutters (without taking off shutter from the frame) area not exceeding 1.50 sqm each and removing complete, all as specified and as directed by the Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 sqm but not exceeding 4 sqm each and removing complete, all as specified and as directed by the Engineer-in-Charge.

Solid PVC door frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as per drawing shown on page No 160 of SSR Part-II (rates) and as directed by Engr-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing on page No. 156 of MES SSR Part-II 2010, complete all as specified and directed by Engr-in-charge.

All as per item no. 04 here-in-above but wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly.

Pressed steel frame of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc; complete all as specified and directed by Engr-in-Charge.

Mild steel wire cloth of 0.63 mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks, or galvanised wire staples in guazed steel windows all as specified and as directed by the Engineer-in-Charge.

Mild steel butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B11 complete all as specified and directed by Engr-in-Charge.

150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-Charge.

150mm long aluminium alloy handles, cast type, anodised complete all as specified and directed by Engr-in-Charge.

Taking down Cement plaster on brick or stone or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-Charge.

Demolition of stone slabs and tiles of any description or thickness laid in cement mortar complete all as specified and directed by Engr-in-Charge.

10mm thick rendering on other than fair faces of brick masonry in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

20mm thick rendering on stone masonry surfaces in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered surface of walls and applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

Two coats of cement based paint on walls including prepration of new or old plastered surfaces complete all as specified and directed by Engr-in-Charge.

Glazed ceramic tiles premium class, grade-I in vertical surface of size 300x200x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 10mm thick bedding layer in cement mortar 1:4 on surfaces of walls, complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete in ground floors, in any position and pavings not exceeding 15cm thickness (below or above ground level) un-reinforced complete all as specified and directed by the Engr-in-Charge.

Demolition of cement concrete in ground floors, in any position and pavings exceeding 15cm thickness (above ground level) un-reinforced complete all as specified and directed by the Engr-in-Charge.

25mm thick plain cement concrete, M-15, type B-1(using 20mm graded crushed stone aggregates) as in floor, finished even & rough to receive floor finishes complete all as spcified and directed by Engr-in-Charge.

Non skid (mat finish) ceramic coloured tiles Primium class-I grade, 7 to 8mm thick (square/rectangular), area of each tiles exc.0.06 sqm but n.exc 0.11 sqm in floors,set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, M-7.5, type D-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete, including necessary formwork where required complete all as specified and directed by the Engr-in-Charge.

Plain cement concrete, M-10, type C-2 (using 40 mm graded crushed stone aggregate) as in surface channel and drain Complete all as specified and directed by Engr-In- Charge

Vitreous China wash hand basin, angle back, size 600x480mm white, including cutting for and pinning in ends of brackets or erecting stand, with 32mm chromium plated waste coupling, waste pipe of bore 32mm, PVC Connection pipe 450mm ling with brass nuts on both side, complete all as specified and directed by Engr-in-charge.

Vitreous chinaware squantting pan, ''Orrisa pattern'', size 580mm x 440mm white, with Cast iron 'P' or 'S' trap, front or back inlet, integral footrest excluding flushing cistern and flush type etc; and making good to floors, complete all as specified and directed by Engr-in-Charge.

Vitreous China Urinals (fixed in repair), bowl type ( back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 , securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. ( Exclusive of fixing supply pipe to flushing cistern , trap and waste pipe) including PVC connections 15 mm size with PTMT nuts of length 600mm & waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed by Engr-in-Charge.

PVC valveless, syphonic action type flushing cistern, crystal white, 10 ltr capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32mm dia PVC long bend flush pipe 90cm long and 15mm dia 450 ling PVC Connection with CP brass coupling nuts and PVC washers at both ends (fixed in repairs) complete all as specified and directed by Engr-in-Charge.

PVC (SWR) floor trap, 75mm bore, plain with grating including jointing with solvent cement, complete all as specified and as directed by Engineer-in-Charge .

110mm bore, PVC (SWR) Pipes, single socketed in any length with rubber ring joints, laid in trenches/ fixed to walls or in floors fixed with solvent complete all as spcified and directed by Engr-in-Charge.

All as per serial item No. 30 here-in-above but 75mm bore.

PVC (SWR) vent cowl of dia 75mm dia complete all as specified and directed by the Engr-in-Charge.

PVC (SWR) reducers 75/110mm bore complete all as specified and directed by Engr-in-Charge.

PVC (SWR) bend any radius, 75mm bore complete all as specified and directed by Engr-in-Charge.

PVC (SWR) bend any radius 110mm bore complete all as specified and directed by Engr-in-Charge.

110mm PVC (SWR) branch pieces, double (double Y), equal or unequal, complete all as specified and as directed by Engineer-in-Charge .

Taking up or down steel tubing and connection, including cleaning for refixing or removal to store for 15mm bore tubing, complete all as specified and directed by Engr-in-Charge.

15mm bore GI tubing, medium grade, galvanised with all fittings and fixtures fixed to wall and celling or laid in floor, complete all as specified and directed by Engr-in-Charge.

20mm bore GI tubing, medium grade, galvanised with all fittings and fixtures fixed to walls and celling or laid in floor, complete all as specified and directed by Engr-in-Charge.

Re fixing only for 15 mm bore GI tubing, medium grade with all fittings, laid under floors of fixed in wall complete all as specified and directed by Engr-in-Charge.

Stop valve, 15mm bore, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions suitable complete, fancy type, chromium plated, complete all as specified and directed by Engr-in-Charge.

Bib taps,15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge.

Shower rose, 125mm, chromium plated, with or without swivel joints, any size, including fixing to steel pipe or union, fixed in repair complete all as specified and directed by Engr-in-Charge.

Tubular towel rail, 20mm dia, D-type, 60cm long between flanges aluminium anodised, fixed in repairs complete all as specified and directed by Engr-in-Charge.

Demolition of Stone masonry work, built in cement mortar complete all as specified and directed by Engr-in-Charge.

Walling of random rubble stone masonry, uncoursed, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 Complete all as specified and directed by Engr-in-Charge

All as per item no 46 here-in-above but except stones.

Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:4 complete all as specified and directed by the Engr-in-Charge.

Chequered cement concrete tiles of size 200X200X25 mm thick set, jointed and pointed in neat cement slurry as in floor with grey cement and pigment including 15 mm thick screed bed in CM 1:6 over 75mm thick PCC, M-10, type C-2, complete all as specified and directed by Engr-in-Charge

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete, all as specified and directed by Engr-in-Charge.

Galvanized corrugated mild steel sheeting 0.63 mm thick with two corrugations side lap fixed with L-type or J type hooks and washers, in roof, walls etc with grade of zinc coating 275 gm complete all as specified and directed by Engr-in-Charge.

All as per item no 51 here-in-above but except sheets.

Plain GaIvanised mild steel sheeting 0.63 mm thick, as in ridges, valley, gutter etc; fixed with L-type or J type hooks and washers, complete all as specified and directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise specified complete all as spcified and directed by Engr-in-Charge.

Mild steel work as in wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

Taking down old unserviceable PVC water tank after removing incoming and outgoing connections of size 1000/ 2000 ltrs & removing to store yard complete all as directed.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position of capacity 1000 ltrs including 15 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed with all fittings and fixtures, complete all as specified and as directed by Engr-in-Charge.

Sch 'A' Part-II: Provn of stair to bldg No. P-120, flush tank & tiles in bathroom of building No. P-91 & Kitchen plate rack in JCOs & ORs Md Accn in Tirah line. Surface excavation not exceeding 30cm deep & averaging 15cm deep and getting out in any type of soil complete all as specified & directed by Engr-in-Charge.

Excavation over area not exceeding 1.5m in depth and getting out in any type of soil complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm thick, complete all as directed by Engineer-in-Charge.

Removing excavated surplus material to a distance n.exc. 50 m and depositing where directed at a level n.exc 1.5m above starting point complete all as directed by Engineer-in-Charge.

Walling of random rubble stone masonry, uncoursed, brought up to courses, well bonded, bedded and solidly hearted and built in cement mortar 1:6, complete all as specified and directed by the Engr-in-Charge.

Plain cement concrete, 75mm thick, M-7.5 (nominal mix), type D-2 (using 40mm graded crushed stone aggregate) as in sub base, foundation, filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, M-15, nominal mix, type B-1, (using 20mm graded crushed stone aggregates), as in coping, bed plates, water trough and the like including weathering, slightly, rounded or chamfered angles and throating, complete all as specified and directed by the Engr-in-Charge.

Chequered cement concrete tiles of size 200X200X25 mm thick set, jointed and pointed in neat cement slurry as in floor with grey cement and pigment including 15 mm thick screed bed in CM 1:6, complete all as specified and directed by Engr-in-Charge

Demolition of cement concrete in ground floors & paving not exceeding 15 cms thick (below or above ground level), complete all as specified and directed by Engr-in-Charge.

Non skid ceramic coloured tiles 6 to 7mm thick, area of each tiles exc.0.06 sqm but n.exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Glazed ceramic tiles premium class, grade-I in vertical surface of size 300x450x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 10mm thick bedding layer in cement mortar 1:4 on surfaces of walls, complete all as specified and directed by Engr-in-charge.

Stop valve, 15mm bore, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions suitable complete, fancy type, chromium plated, complete all as specified and directed by Engr-in-Charge.

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

15mm bore GI tubing, medium grade, galvanised with all fittings and fixtures fixed to wall and celling or laid in floor, complete all as specified and directed by Engr-in-Charge.

25mm thick plain cement concrete, M-15, type B-1(using 20mm graded crushed stone aggregates) as in floor, finished even & rough to receive floor finishes complete all as spcified and directed by Engr-in-Charge.

PVC valveless, syphonic action type flushing cistern, crystal white, 10 ltr capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32mm dia PVC long bend flush pipe 90cm long and 15mm dia 450 ling PVC Connection with CP brass coupling nuts and PVC washers at both ends complete all as specified and directed by Engr-in-Charge.

75mm bore PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified & directed by Engr-in-Charge.

Grating doom 125mm dia PTMT(min wt 40gm) complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed by Engr-in-Charge.

Vitreous chinaware squantting pan, ''Orrisa pattern'', size 580mm x 440mm white, with Cast iron 'P' or 'S' trap, front or back inlet, integral footrest excluding flushing cistern and flush type, etc and making good to floors (fixed in repair) complete all as specified and directed by Engr-in-Charge.

Demolition of stone slab/ Trezzo/ tilesof any thickness in any position complete all specified and directed by Engr-in-charge.

PVC connection 15mm size with brass nutsat both ends of length 450mm of superior quality screwed down for high pressure, complete all as specified and directed by Engr-in-Charge.

PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joint, laid in trenches / floor, complete all as specified and directed by the Engr-in-Charge.

Stainless steel plate rack of size 600 x 600 x 250mm with all fittings complete all as specified and directed by Engr-in-charge.

Sch 'A' Part-III: Internal Electrification Works in Bldg No P-152 ( OR's Toilet & Bathroom block) in Bharatpur line. Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulators sockets etc to be measured separately), for taking credit (credit for above items should be made as per conditions separately) complete all as specified and directed by the Engr-in-charge.

Point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheathed FRLS electric cable 1100 volts cable and including PVC conduite 20mm dia with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including wooden box covered with 3 mm thick plastic laminated sheet for one light point/ fan/exhaust fan point/ bell point etc controlled by one, one way switch,complete all as specified and as directed by the Engineer-in-Charge. Make: Havells/Plaza/Polycab Note: (i) New Sunken boxes wherever required shall be measured & paid separately. (ii) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost. (iii) Electric rewiring should be followed by proper colour coding i.e. Red for phase, Black for neutral and Green for Earth.

All as serial item no 83 here-in-before, but for one socket outlet 15Amps on independent board with 2.5 Sqmm copper conductore (Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductore as continuous earth wire connected to common earth dolly complete allas specified and as directed by Engineer-in-charge.

Switch socket combination 2 in 1, 5 Amp and 15 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge. Make: Havells/CONA/Crabtree/SSK

Switch piano, flush type, single pole, one way,5/6Amp, complete all as specified and as directed by the Engineer-in-Charge. Make:- Havells/CONA/Crabtree/SSK

Ceiling rose, surface type, 65 mm x 50 mm, two to three terminals/ PVC/ polycarbonate, isolated body fixed on PVC block, complete all as specified and as directed by the Engineer-in-Charge. Make:- Havells/CONA/Crabtree/SSK

Supply & fix (in replacement ) of existing unserviceable Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 8 way double door type with 200 amp rated bus bar complete all specified and as directed by the Engineer-in-Charge. Make: Havells/Legrand/SCHNIDER Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) The disturbed surface shall be match with existing surface. Make: Havells/Legrand/ABB

Supply and fix (in replacement) MCB SPN 10-40 Amp breaking capacity 10 KA, complete all as specified and directed by the Engineer-in-Charge. Make: Havells/ Legrand/ABB

MCB SP up to 6-32 Amp complete all as specified and directed by the Engineer-in-Charge. Make: Havells/ Legrand/ABB

Energy efficient LED integrated batten, suitable for indoor applications tube light fitting 1x18 Watt 4 FT complete, integrated channel white including LED tube light & all fixing arrangement complete, all as specified and as directed by the Engr-in-Charage. Make: Crompton Cat Part No LCTL-18-CDL or equivalent in Philips/BAJAJ/HAVELLS/WIPRO.

Energy efficient LED integrated batten, suitable for indoor applications tube light fitting 1x10 Watt 2 FT complete, Trim LED NEO including all fixing arrangement complete, all as specified and as directed by the Engr-in-Charage. Make: Crompton/ Philips/BAJAJ/HAVELLS/WIPRO.

LED street light fitting 1x25 watt with lamp pressure die cast housing with epoxy powder coated dark graphite grey colour finish, prismatic polycarbonate cover with individual LED lenses with bracket of made of GI pipe 1.5 mtr length,bent to the shape including necessary clamps, nuts bolts etc; complete all as specified and as directed by the Engr-in-Charage. Make Crompton Cat Part No LSTS 25CDI LED or equivalent in Philips/OSRAM/CG

Exhaust fans, AC, single phase, 230/240 V of size 300 mm sweep with louver complete all as specified & directed by Engr-in-Charge and as directed. Make : CG/HAVELLS/USHA Note:Labour charges for fixing including electric connection & making hole in wall and plaster work shall be part of job at no extra cost.

Electric water heater, storage type, capacity 25 ltr, BEE 5 star rated complete all as specified and directed by Engr-in-Charge. Make: Jaquar Model Elena/Racold Model ALTRO 2/Venus Model: WAVE Note : Fixing of geyser on wall with suitable size anchore bolt with hammer drill and making good the disturbed surface including plaster work shall be part of job at no extra cost.

Galvanised iron pipe, medium grade, 15mm bore, ISI marked with screwed socket joints together with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, lugs and union etc., laid in trenches/floors or fixed to walls etc; complete all as specified and directed by Engr-in-charge.

PVC Bib tap standard of PTMT, any colour,15mm bore, high pressure screwed for iron pipe, complete all as specified and directed by Engr-in-Charge.

Stop valve,15mm bore, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions suitable complete, fancy type, chromium plated, complete all as specified and directed by Engr-in-Charge.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick burried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40x40x6mm and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate complete all as specified and shown in EP-3 of SSR Part-I & as directed by Engr-in-Charge.

1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections, one twin core cable flat or circular stranded conductor of size 10 Sqmm, 2 core, complete all specified and as directed by the Engineer-in-Charge.

House service bracket ( hook type) complete with 3.0m long G.I pipe, 40mm dia, medium grade, two Nos 90 Degree bends. M.S. hook etc, complete all as specified and directed by the Engineer-in-Charge.

M/S DAYA SONS