Provision of Electrical skilled manpower for operation of lifts and maintenance of E.I. work at various floors of TEC, K.L. Bhawan, New Delhi

SH-I (Man Power) Provision of Manpower for smooth functioning of Electrical Maintenance & Operation of A.C, E.I, Lift, Compound Light, Pumps and Motors for water supply to the Bldg./colonies and offices etc. The manpower will work as electrical enquiry to receive complaints from Officers/residents of staff quarters/Offices at different locations and to attend the fault/restore the Power supply/ breakdown maintenance against the supply of material by the department except minor modification/ alternate arrangement, etc. complete in all respect to the entire satisfaction of Engineer-in-charge. Note: Manpower may be asked to work at other locations also and in any shift without any extra cost as per requirement under the jurisdiction of EE(E) /SDE (E), BSNL. Decision of Engineer-in-charge will be final. Staff required (not above the age of 55 years): -

Skilled Manpower having valid electrical licence/ permit – 02 nos.

Unskilled Manpower capable to assist in all type of electrical works – 02 nos.

Replacement/Provision of following material for repairing & attending petty maintenance work by engaging adequate manpower as required at site for repairing of HT/LT panels, capacitor panels, existing wiring work like fluorescent fitting, ceiling fans, wall/pedestal fans, Main board, Sub-Main board, Compound Lighting, water pumps & switchgears, Geysers, Split AC, water coolers, etc i/c dismantling, connection, fixing, testing etc as required. (NOTE-The material under replacement shall be similar to existing defective material and the dismantle material will be property of the contractor. The rates should be quoted accordingly.).

5/6A, One way Piano type Switches

15/16A, One way Piano type Switches

5/6A 3/5 pin piano type Socket outlet

15/16A 3/6 pin piano type Socket outlet

5/6A, Two-way Piano type Switches

5/6A Modular type Switches

15/16A Modular type Switches

5/6A 3/5 pin Modular type Socket outlet

15/16A 3/6 pin Modular type Socket outlet

5/6A, Two-way Modular type Switches

Modular type Bell push Switches

Bell push switch

Bell Buzzer

3 mm thick Hylam Sheet

Angle Holder

Single pole MCB - upto 32A

SPN MCB- upto 32A

40A, 240V DP Isolator

63A, 240V DP Isolator

63A, 415V FP Isolator

100A, 415V FP Isolator

Capacitor - 2.5 MFD/ 3.5 MFD

Fan regulator - electronic step type

9-Watt, 230 Volt, 50 Hz LED Lamps

PVC Switch box for 3nos 5/6 A Switch and sockets

PVC Switch box for 1nos 15/16 A Switch and sockets

Remote Call Bell

Supply of 25 mm medium class PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Rewiring Group -C for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/recessed steel/PVC conduit including dismantling as required.

Supply of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 25 A modular socket outlet and 25 A modular SPMCB "C" curve including connection, painting etc. complete as required.

Supply of DP sheet steel enclosure on surface/recess along with 25/32 A, 240 V “C” curve DP MCB complete as required.

Supply of following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.

3 x 1.5 sq. mm

3 x 2.5 sq. mm

3 x 4 sq. mm

2 x 0.5 Sq.mm Twin Flat Cable-White

Supply of following sheet steel MCB DB, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator)

8 way, 240V SPN, Double door

12 way, 240V SPN, Double door

Supplying of following sizes of PVC casing and capping for covering of loose wires etc. Complete as required.

25 mm x 16 mm

32 mm x 16 mm

50 mm x 16 mm

Supplying of 3 x 4 Sq. mm PVC insulated, PVC sheathed copper conductor round flexible cable of 1.1 KV Grade on surface/wall i/c making connections, testing etc complete as required.

Supplying of PVC insulated, PVC sheathed copper conductor armoured cable of 1.1 KV Grade on surface/wall i/c making connections, testing etc complete as required.

3 x 1.5 Sq. mm

3 x 4 Sq. mm

Supply of following type heavy duty exhaust/ wall/ ceiling fans suitable for operation on 230V, 50 Hz single phase AC Supply i/c dismantling/ refixing, minor civil works if reqd. making connection testing and commissioning etc complete as required.

250 mm sweep Plastic Ventilation Fan with front louvers

400 mm sweep, 1350 rpm, Plastic body wall fan

1200 mm sweep, BEE 5 star rated, ceiling fan

Supplying of 20w, 6500K, 1200mm long LED tube with batten/box LED Fittings on surface of wall/ below roof, connection with 3x1.5 Sq.mm flexible wire, testing, commissioning etc. complete as required.

Replacement/SITC of Energy Efficient Ultra-modern 595mm x 595mm size LED luminaire having following specifications i/c dismantling of existing outlived/ faulty conventional luminaire with high brightness SMD LEDs, making suitable arrangement for installation etc. complete as reqd. in all respect to the entire satisfaction of Engineer-in-charge: - a) Wattage: 36 Watt + 10% b) System lumens efficacy: Not less than 100 lumen per watt c) Driver efficiency: Not less than 85% d) THD: Not more than 10% e) CRI: Not less than 80 f) UGR: Less than 19% g) LED Life: Not less than 50000 hours @ LM 70% h) Colour temperature: 5500 - 6500 K i) Operating voltage range: 140 Volt to 270 Volt j) Installation type: Recess Ceiling installation K) Material of construction for housing: CRCA powder coated white after phosphochromate treatment l) Material of construction for cover: Scratch resistant and polycarbonate diffuser / cover m) Electronic Driver: independent Isolated type (Constant current supply) n) Internal surge protection: Not less than 2.5 kV o) Ingress protection (IP): Not less than 20

Replacement/SITC of Energy Efficient Ultra-modern bright 20W, 1200 mm Long LED Polycarbonate tube light (Single Side Connection) having following specifications i/c dismantling of existing outlived/ faulty conventional tube lights from existing fitting etc. complete as required: a) Wattage: 20 Watt + 10% b) System lumens efficacy: Not less than 110 lumen per watt c) Driver efficiency: Not less than 85% d) THD: Not more than 10% e) CRI: Not less than 80 f) LED Life: Not less than 50000 hours @ LM 70% g) Colour temperature: 5500 - 6500 K h) Operating voltage range: 160 Volt to 270 Volt i) Installation type: Wall / Ceiling surface installation j) Material of construction for housing: Polyuminum die cast k) Internal surge protection: Not less than 2.5 kV l) Ingress protection (IP): Not less than 20.

Replacement of faulty compound light by providing, installation, testing commissioning of 45 watt 5700 K Energy saving ,environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP 66 protection and impact resistance and suitable for operation on 230 volt ac supply on existing pole/wall i/c making connections and testing the poles, etc. complete as required.

Supply of weather proof PVC Pole Box of size 200 mm x 250 mm x 100 mm deep, i/c providing din rail, 1 no. 6A SP MCB, 1 no. 4 way neutral link, 1 no. heavy duty MS clamp, nut-bolts, washer etc. complete as required.

Supply of 6 Amp 4 outlet power strip controlled by common switch with surge protection suitable for 230 Volts, 50 Hz Single phase AC supply having connecting lead, safety fuse etc. complete as required.

Remarks: 1. Manpower will be deployed by the agency at site to receive the complaints and for co-ordination for the work. For this, one mobile no. with WhatsApp facility will be provided by the agency. 2. Skill manpower will also be required to rescue the trapped person in the lifts at once. 3. Adequate inventory of material will be kept at site by the agency for prompt attending the complaint. 4. Complaint received in Fore Noon will have to be attended by After Noon and complaints received in Afternoon will have to be attended by Forenoon of next day. Emergency complaints, if any, will have to be attended immediately at any time including odd hours. 5. Penalty of Rs. 500/- per complaint per day will be imposed for non-compliance of the complaint. If at any stage, it is observed that the performance of agency is not adequate, work will be rescinded, and the agency will be debarred from doing any work for one year in Delhi region. The work will then be carried out at his risk and cost without serving any notice 6. The Agency should quote amount keeping in view all Statutory requirements including minimum wages/ESI/EPF etc. 7. Replacement, Servicing & Scrap/ dismantle items will be credited to the firm. The rate may be quoted accordingly.

Note:- 1. The GST / other Input Tax Credit (ITC) taxes shall be quoted by the firm as applicable as per latest amendments of GST Rules. 2. The contractor shall provide correct tariff heads & other details to enable BSNL claim Input Tax Credit. 3. Servicing Scrap items will be credited to the firm. The rate may be quoted accordingly. 4. Bidder must mandatorily quote for all GST components (CGST, SGST, and IGST) as required. 5. If annual maintenance contract charges are required to be quoted as per SOW, basic charges should be shown in column 4 & the Goods and Service Tax (GST) in column 7 to 12. 6. The bidder who submits the offer with concessional Goods and Service Tax (GST) shall submit the proof of applicable concessional GST. In case the Concessional GST is not creditable to BSNL it should be included in the price of the goods/services. 7. In case, dealer is registered under compounding scheme or any rule/notification where the BSNL is not eligible for input tax credit then the bidder should not disclose any amount in column 7 to12 & 14. 8. % age Rate of FF & Packing should be shown of basic unit price excluding all taxes & charges (i.e. as %age of col.4). 9. The FF & packing amount quoted shall not be subject to change after bid evaluation /ordering on account of change of copper, lead base price, change in duties & taxes of item etc. 10. Bidder must mandatorily mention HSN & SAC numbers.15. Evaluation of bids: - The evaluation and comparison of responsive bids shall be done on the basis of Net cost to BSNL on the prices of the goods & Services (i.e. complete work) offered along with all applicable Taxes, packing Forwarding Freight & Insurance charges etc. exclusive of GST. Declaration by Bidder: 1. We hereby declare that in quoting the above prices, we have taken into account the entire credit on inputs available under the GST Act introduced w.e.f. 1 July 2017 and further extended on more items till date. 2. We hereby certify that HSN/SAC shown in column 17 are correct & credit of GST for the amount shown in column 14 above are admissible as per GST Laws. Name of bidder: Seal of Company:

kashyap electricalsd

STAR ELECTRIC WORKS

M/s ROHIT ENTERPRISES

Mahajan Sales Corporation

BRIGHT REFRIGERATION WORKS