e-NIT No.- 01/COB I BDO/2026-27, SL-01

Clearing and Grubbing Road Land Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness. (Reference to MoRT&H's specification clause 201) 3(I) By Manual Means 3(I)(A) In area of light jungle

Scarifying Existing Bituminous Surface to a depth of 50 mm by Mechanical Means Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material within all lifts and lead upto 1000 metres (Reference to MoRT&H's specification clause 305.4.3).

Maintenance of Earthen Shoulder (filling with fresh soil) Making up irregularities/loss of material on shoulder to thedesign level byadding freshapproved soil and compacting i twith appropriate equipment as per the requirement of MORT&H's specification 3003.

Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400-13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406.

Prime Coat : (A) Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502).

Tack Coat Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).

Close Graded Premix Surfacing/Mixed Seal Surfacing (Reference to MORT&H's specification clause 508). Mechanical means using HMP of appropriate capacity not less than 75 tonnes/hour. Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composedof 11.2mmto0.09mm (Type-A) or13.2mmto0.09mm (Type-B) aggregates using viscosity grade bitumen of suitable approved grade to the required line, grade and level to serve as wearing course on a previously preparedbase, includingmixing in asuitableplant, laying and rolling with a Smooth wheeled roller8-10 tonne capacity, and finishing to required level and grade. (i) Type-A. (rainfall more than 150cm/year)

Providing, supplying, erection, fixing, fixing etc. all complete in all respect with all incidental charges for informatory sign Board having M.S. Channels/ angel posts & 1.5 mm th. M.S. sheet & synthetic enamel paint over a coat of promer including lettering over cement concrete (1:3:6) with jhama khoa or with local stone chips etc. complete including painting two coats on both faces etc. complete as per direction of the Engineer-in- Charge. Size of M.S. sheet : 1200 X 900 X 1.5 mm thick. Size of vertical angle : 40 X 40 X 6 mm thick. Height of vertical angle: Above GL= 1000 mm. : Below GL= 800 mm. Size of horizontal angle: 30 X 30 X 3 mm thick.

As applicable GST 18.00%

As applicable 1.00% Labour Cess