Constructon of shelter shed

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth upto 50 meter as directed: all kinds of soil

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) including carriage of material all complete

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including carriage of material all complete

Supplying and laying in position stone boulders of size not more than 150mm inclusive of all carriages leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form work for footings foundations base of columns including carriage of material all complete

50mm thick Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete

Random Rubble masonry with dry Hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement :6 coarse sand) including carriage of material all complete

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing precoated galvanized iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side ofthe sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or asdesired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gram/m2

Providing and laying stone aggregates as in under flooring in plinth with available earth and sand in the ratio of 50% boulders (Total 4.86cum)well rammed in layers.

Providing and laying stone aggregates as in under flooring in plinth with available earth and sand in the ratio of 30% sand (Total 4.86cum)well rammed in layers.

Providing and laying stone aggregates as in under flooring in plinth with available earth and sand in the ratio of 20% available earth (Total 4.86cum) well rammed in layers.

Providing and Laying of 15mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 coarse sand)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work an under coat of suitable shade with ordinary paint of approved brand and manufacture

CIB (Citizen Information Board ) size 4'-0" x 5'-0" x 0'-9" (above plinth level ) with tepered top having 20 degree slope in Brick Masonary (1:4) including plaster , paint , lettering and logos as per instruction of Engineer-in-charge incuding carriage of material. (complete job)

mohd younis butt

Nawaz Ahmed