AS-16-161 Balance work of Construction of road from Chamuakhat to Panbarihabi Road

Amount

Construction of sub-grade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporating to site, spreading, grading to required slope and compacting to meet required of Table 300.2 with lead upto 1000m as per technical specification clause 303.1. (A) Private Land

Construction of Granular sub-base (A) By mix in Place Method, Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.(II) For Grading Material (Gr - II )

Water Bound Mecadam Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. 2) Grading-II (A) By manual Means

Water Bound Mecadam Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405.3) Grading-III (A) By manual means

Prime-Coat (i) Low porosity Providing and applying primmer coat with bitumin emultion (SS-1) on prepared surcafe of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical Clause 502.

Tack-coat (III) Providing and applying tack coat with bitumin emultion (RS-1) using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface tresated with primer & cleaned with hydraulic broom as per technical specification clause 503.

20mm thick open graded Premix carpet using bituminous (penetration grade/ modified bitumen) Binder Providing , laying and rolling of open graded premix carpet of 20mm thickness composed of 13.2 mm to 5.6mm aggregate eithe rusing penetration grade bitumen or emultion to required line, grade and level to surfe as wearing course on a previously prepared base, including mixing in a suitable plan, laying and rolling with a three wheeler 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical specification clause. Case-II By Mechanical Means (i) Bitumen (S-90)

Seal-Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause B) By mechanical means. Case I Type-A (i) Bitumen (S-90)

Trafic - Signs B. Semi Reflective Traffic Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle Iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x600mm, 600mm below ground level as per drawings and Technical Specification clause 801 (i) 90 cm equilateral triangle

Trafic - Signs B. Semi Reflective Traffic Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle Iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x600mm, 600mm below ground level as per drawings and Technical Specification clause 801 (ii) 60cm Circular

Trafic - Signs B. Semi Reflective Traffic Signs (1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle Iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x600mm, 600mm below ground level as per drawings and Technical Specification clause 801 (ii) 80cm x 60cm rectangular.

Kilometer Stone Reinforce cement concreter M15 grade kilometer stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and technical specification clause 1703. (i)Ordinary Kilometer Stone (precast)

Kilometer Stone Reinforce cement concreter M15 grade kilometer stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and technical specification clause 1703 (ii) 200 m Stone (precast)

Providing and Fixing 'Logo' of PMGSY Project Providing and fixing of typical PMGSY informatory sign board with logo as per MORD specifications and drawing. Three MS plates of 1.6mm thick, top and middle plate will be welded with MS flat iron 25mm x 5mm x size on back on edge. The lower plate will be welded with MS angle iron 25mm x 25mm x 5mm. The anfle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embeded in cement concrete M15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The topmost dimond plate will be welded to middle plate by 47mm X 47mm of 12 SWG steel plate tube. All MS will be stove enameled on both sides. Lettering and printing arrows, borders etc. will be painted with ready mixed synthetic emnamel paint of superior quality in required shade and colour. All sections of framed posts and steel tuube will be painted and two coats of epoxypaint as per specification clause 1701 and Annexure 1700.1

Providing and laying Speed breaker

1)Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification Clause 1908

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202.(A) Upto 600 mm dia Hume pipe

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202.( B )Above 900 mm dia Hume pipe

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides a (I) Ordinary Soil (A) Manual means (b) With dewatering

PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)

Laying (First class) bedding on well compacted sand, moorum as per clause 1105(ii) Granular material

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106.(B)1000 mm dia

Brick Masonry Work in cement mortar in foundation of Head walls complete exculding pointing and plastering as per drawing and technical specification Clause 1109 Brick Masonry in 1:4 cement mortar

Plastering with cement mortar (1:3) on brick work in sub structure as per technical specification

Routine Maintenance for 1st Year (The Bidder has to quote the exact amount as mentioned in estimated rate)

Routine Maintenance for 2nd Year (The Bidder has to quote the exact amount as mentioned in estimated rate)

Routine Maintenance for 3 rd Year (The Bidder has to quote the exact amount as mentioned in estimated rate)

Routine Maintenance for 4th Year (The Bidder has to quote the exact amount as mentioned in estimated rate)

Routine Maintenance for 5th Year (The Bidder has to quote the exact amount as mentioned in estimated rate)