REPAIR TO ROOFING AND ALLIED WORK IN ZONE B AND POST CONSTRUCTION ANTI TERMITE TREATMENT IN CERTAIN BLDG IN ZONE A IN TECH AREA AT AF STN SURATGARH

Amount

BOQ (REPAIR TO ROOFING AND ALLIED WORK IN ZONE 'B' AND POST CONSTRUCTION ANTI TERMITE TREATMENT IN CERTAIN BLDG IN ZONE A IN TECH AREA AT AF STN SURATGARH)

Dismantling brick tiles or terracing tiles sinlge layer on roofs complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for wire brushing neat cement slurry with 3kg of cement per sqm at top and bottom of base coat and cleaning top surface complete all as specified and directed.

M&L for average 50mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) to be provided in slope as in roofing coverings etc. complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:4 with water proofing compound @ 3% by weight of cement on brick work or concrete surfaces in cement mortar 1:4 including finishing the surface even and smooth without using extra cement complete all as specified and directed. Note:- Water proofing compund shall be measured and paid separately

M&L for rendering 15mm thick in CM 1:4 with water proofing compound @ 3% by weight of cement on brick work or concrete surfaces in cement mortar 1:4 including finishing the surface even and smooth without using extra cement complete all as specified and directed. Note:- Water proofing compund shall be measured and paid separately

Supply only integral waterproofing compound, complete all as specified and directed.

M&L for mineral finish APP based polymeric membrane minimum weighing 3kg/sqm and min 3mm thick reinforced with polyster non woven fabric (wt not less than 150gms/sqm) laid on primed surface by torced application and applying two coats of aluminium paint over surface complete all as specified and directed.

M&L for 40mm thick brick tiles laid on cement mortar and joints grouted and flush in cement mortar(1:3) mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified and directed.

All as per item No 9.00 above here-in-before but except tiles, complete all as specified and directed.

M&L for flush pointing to brick laid flat or brick tiles in paving in cement mortar 1:3, complete all as specified and directed.

Taking down shutter with chowkhats not exc 1.5sqm complete all as specified and directed.

Taking down shutter of any description area exc. 1sqm but not exc 2sqm each and removing from site complete all as specified and directed.

S&F for 150mm size extruded aluminium alloy handles, fabricated type anodised section ,ISI marked complete all as specified and directed.

S&F for 200mm long aluminium anodised barrel tower bolts of extruted section complete all as specified and directed.

S&F for 100mm butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F for aluminium anodised, coloured powder coated door chowkhats with one or more rebate using section of size 101.60mmx44.75mmx3.18mm with jointing cleats for fixing etc fixed to wall including taking down old existing door frame of any description complete all as specified and directed.

S&F in repair aluminium (extruded section body) door closer hydraulically regulated, designation No.2, universal type, suitable for door shutter of 701 to 850 mm in width & of weight between 36kg to 60kg complete all as specified and directed.

S&F for aluminium window and ventilator shutters,sliding type with two track without sash bars, aluminum sections of size 40mmx20mmx1.5mm fixed in aluminum anodised frame of section size 63.5mmx38.18mmx2mm including necessary jointing cleats, glazing clips , aluminium anodised snap beading ,screws,aluminium beading , pvc packing , aluminium anodised fittings & fixtures with and including stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperature 1.40mm and fixed with tinned tacks or steel wire staples and necessary fittings & fixtures including powder coating of thickness n.exc 50 micron on all aluminum section , including taking down old existing window shutter complete all as specified and directed. Note:- Rate of mild steel wire shall be included in quoted rate of this item nothing extra shall be admissible on this account

S&F for aluminium window shutter sliding type of size 40mmx20mmx1.5mm in section fixed in aluminum anodised frame of section size 63.5mmx38.18mmx 2mm including necessary jointing cleats , glazing clips , aluminium anodised snap beading ,screws, aluminium beading , pvc packing , aluminium anodised fittings & fixtures with and including 4.80mm thick tinted glass with necessary beading / packing and necessary fittings &fixtures ,including taking down old existing window shutter complete all as specified and directed. Note:- Rate of glazing shall be included in quoted rate of this item nothing extra shall be admissible on this account

S&F for aluminium chequered grills as on aluminium windows, weight not exc .0.50 kg/sqm and fixed including taking down of old unservicable grill, complete all as specified and directed.

S&F for solid panel PVC door frame 50mmx47mm made out of 5mm plain covered PVC sheet, reinforced with MS square tube and fixing in opening complete all as specified and directed.

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS. tubes for top & bottom rails. MS. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fit-ted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site complete all as specified and directed.

S&F for floor door stopper 140mm long of aluminium alloy and double tounge anodised with hard drawn steel spring complete all as specified and directed.

S&F repair to aluminium door shutter of any description including taking down from the chowkhat and refixing the same in position after repairing, tightening of frame including new screws, cleats etc. , complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description ) from metal frames , glazed with putty or fixed with beads and providing and fixing new ones complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5sqm in each pane complete all as specified and directed.

M&L for 3mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.5sqm in each pane complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F for rubber beading for doors of any required size and having a width not exc 30cm complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer (grills/gates of security compound walls) complete all as specified and directed.

M&L for prepration of old painted surfaces of steel and steel based materials of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Dismantling boarding of any description fixed in any position with nails in CB's loft, showcases, utensil racks etc complete all as specified and directed.

S&F for 19mm/20mm pre-laminated partical board exterior grade both side laminated board fixed with screws complete all as specified and directed. Make:- Kit Ply/Mayur/Archid

S&F for 40mm width continuous (piano) hinges,mild steel bright finish or electrogalvanised complete all as specified and directed.

S&F for magnet catcher suitable for cupboard shutter complete all as specified and directed.

Easing of door/window or cupboard (complete for one No door or window) shutter of any size/any number of pannels for easy closing/opening, tightening of hinges or changing the position of hinges adjustment of tower bolt, sliding bolt, door spring, door handle etc, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles of approved shade of size 450mmx300mmx7mm to 8mm thick as in dado etc set and jointed in white or coloured cement to match the surfaces (existing) laid over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7mm to 8 mm thick (square/rectangular) area of each tile exc 0.06sqm but not exc. 0.11sqm ,in floors etc . set &jointed in neat cement slurry and pointed in white or coloured cement to match with shade of tiles over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7mm to 8mm thick ( square/rectangular) area of each tile exc 0.11sqm but not exc 0.18sqm ,in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for vitrified tiles of premium quality, light shade, 10mm thick (square/rectangular) area of each tile not exc 0.36sqm, laid in floors with neat cement slurry @ 3.00 kg/sqm over and including 15mm thick screed bed in cement mortar 1:6 including pointing in white cement with pigment to match the shade of tiles,complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300mmx200mmx7mm thick as in vertical surface such as skirting , dado and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for vitrified tiles of premium quality, light shade, 10mm thick (square/ rectangular) area of each tile not exceeding 0.36sqm as in skirting, set and jointed in neat cement slurry, over and including 10mm thick rendering of cement mortar 1:4 including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exc 15cm thickness (below or above ground level) and rubbish off the premises complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate)as in plinth protection finished even and smooth without using extra cement including forming necessary joints 12mm wide to the full depth of PCC at every 3 metres and every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete with and including necessary form work etc complete all as specified and as directed.

M&L for 75mm thick PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in top surface of hardstanding/path etc, finished the surface even and smooth without using extra cement complete all as specified and directed.

Dismantling of paverblock/tiles of any description or thickness in floors, aprons etc. laid dry or laid dry pointing complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base, floor complete all as specified and as directed.

M&L for factory made machine pressed precast concrete interlocking paver block ISI marked any shape or size confirming to IS 15658 of 80mm thickness M-35 grade with grey cement and no pigment laid over and including 25mm thick sand cushioning and filling the joints upto full depth with fine tibba sand, complete all as specified and directed.

Fixing only retrived machine pressed precast concrete interlocking paver block/tiles any shape or size with grey cement and no pigment laid over and including 25mm thick sand cushioning and filling the joints upto full depth with fine tibba sand, complete all as specified and directed.

Dismantling plain or corrugated asbestos cement sheeting, any thickness as in roof covering or wall cladding complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugaed steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S&F for mild steel plates, plain or chequered, in 5mm thick or over in thickness in available sizes, Fe 410-W (Gde E-250) quality complete all as specified and directed.

S&F steel work as tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade st-240 complete all as specified and directed.

S&F mild steel framed work such as in doors/chowkhats or gates of angle or other section with gusset plates, rail, braces etc. complete drilled for fixing of steel sheeting or other covering. doors etc. to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening & fixing and similar work conforming to Fe-290 grade E-165 , complete all as specified and directed.

Demolition of stone slabs & tiles of any description or thickness in floor aprons, cills etc laid bedded & pointed in any mortar complete all as specified and directed.

M&L for 18mm-20mm thick granite (of any type) work (table rubbed and polished) in cooking platforms and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Taking down old cement plaster including racking out joints hacking for key, scrubbing down with water etc and rubbish off the premises complete all as specified and directed.

M&L for rendering 12mm thick on brick work or concrete surface in CM 1:4 including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and appying two coats of distemper oil emulsion paint of any description over and including one coat of chalk whiting complete all as specified and directed.

M&L for two coat of cement base paint on newly plastered surface in camouflage pattern including preparation of surface complete all as specified and directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars, etc, and rubbish off the premises complete all as specified and directed.

M&L for bricks work with sub class 'B' bricks straight or cuvred on plan mean redius bult in cement mortar 1:6 complete all as specified and directed.

M&L for bricks work with sub class 'B' bricks old size straight or cuvred on plan to any radius in half brick thick wall built in cement morter 1:4 complete all as specified and directed.

M&L for rendering 10mm thick on brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed.

S&F for 8mm thick hollow printed coloured PVC sheet wall lining/panelling including frame work made of 1mm thick PVC sheet in strips and channels feathered at the edges for fixing of wall lining inclusive of solvent cement and fixing at site , complete all as specified and directed.

S&F for gypsum ceiling board of size 595mmx595mm x12mm thick as in ceiling, fixed with screws on GI grid frame work of size 600mmx600 mm, GI T-section of size 25mmx25mmx1.25mm, GI L-section 25mmx25mmx1.25 mm, hanging arrangements with roof with GI wire not less than 2.00mm dia, including applying two coats of distemper oil emulsion (of approve shade) after preparation of surface, including taking down existing ceiling board of any description complete all as specified and directed.

S&F for fibre insulation ordinary type board 12mm thick of any size (size of board as per site requirement) as in ceiling, fixed with screws on GI grid frame work, GI T-section of size 25mmx25mmx 1.25mm, GI L-section 25mmx25mmx1.25mm, hanging arrangements with roof with GI wire not less than 2.00mm dia, including applying two coats of distemper oil emulsion (of approve shade) after preparation of surface, including taking down existing ceiling board of any description as per manufactures instructions , complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valves with Iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F in repair ball valve 20mm high pressure PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. ( minimum weight 20mm- 210gm complete all as specified and directed.

Taking up and down steel tubing and connections 15mm bore including cleaning for refixing or removal from the site complete all as specified and directed.

Taking up and down steel tubing and connections 20mm bore including cleaning for refixing or removal from the site complete all as specified and directed.

S&F for GI tubing 15mm bore medium grade with all fitings fixed to wall, ceiling or laid in floor, complete all as specified and directed.

S&F for GI tubing 20mm bore medium grade with all fitings fixed to wall, ceiling or laid in floor, complete all as specified and directed.

S&F for refixing old steel tubing of 15 mm bore and connections in new or old position in walls, ceiling and floors etc complete all as specified and directed.

S&F for refixing old steel tubing of 20mm bore and connections in new or old position in walls, ceiling and floors etc complete all as specified and directed.

Dismantling existing water storage tanks exc 250 litres but not exc 500 litres capacity and removal from site complete all as specified and directed.

Dismantling existing water storage tanks exc 500 litres but not exc 1000 litres and removal from site complete complete all as specified and directed.

S&F for rotational moulded polythylene White water storage tank double layered 500 litres capacity (cylindrical vertical with thread cover closed top) hoisted and fixed in position including GI tank nipple, with union (two Nos each) fittings and making necessary connections to make the tank functional complete all as specified and directed.

S&F for rotational moulded polyethylene white water storage tanks 1000 litres capacity (Cylindrical vertical with thread cover closed top) double layered, hoisted & fixed in position including GI tank nipple with union (two No each) fittings and making necessary connections to make the tank functional complete all as specified and directed.

S&F in repairs, PVC float valve 15mm dia, high pressure with polythene float and fly nut screwed for iron pipe or brass ferrule complete all as specified and directed.

M&L for providing and injecting chemical emulsion for post constructional anti-termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for providing and injecting chemical emulsion for post constructional anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

Post construction treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.50ltr /hole by drilling 6mm dia. Hole at a down ward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Contract Amount shall be derived after affecting the amount of Schedule of Credit in General Summary on serial page No 17 tender documents.

H S BUILDERS

M/s Shubham Enterprises

SRI SAI CONSTRUCTION COMPANY