SPECIAL REPAIRS TO BLDG NO P 201 OR MD ACCN P 210 AND P 211 CYCLE SHED AT CHURCH ROAD OF CAFVD KIRKEE UNDER GE C KIRKEE

Amount

Taking down chowkats and frame n.exc 1.5 Sqm each of any type including shutters without taking off shutters from the frame and removing from site complete all as specified and as directed.

Taking down chowkats and frame exc 1.5 Sqm but n.exc 4.00 sqm each of any type including shutter wiuthout taking off shutter from the frame and removing from site complete all as specified and as directed.

Taking down shutters of any description n.exc 1.00 sqm each resecuring, easing, adjusting and re-fixing in same opening after minor repairs including all necessary fittings complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each resecuring, easing, adjusting and re-fixing in same opening after minor repairs including all necessary fittings complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description n. exc 1.00 sqm each and removing to store complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each and removing to store complete all as specified and as directed by Engineer-in-Charge.

S & F Pressed steel door frame for doors of size 125 x 60mm with double rebate including necessary fixing lugs, hinges, lock strike plate, etc complete with and including hollow section of frame to be filled with PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) complete all as specified and as directed by Engineer-in-Charge.

S & F 2nd class hard wood 35mm thick plain framed panelled factory made door shutters (two panels) with lock rail and panel of 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

S & F 35mm thick 2nd class HW glazed or skelton shutter open rebated divided into square with plain chamfered or rounded mitred and rebated without sash bar and prepared to receive gauze or glaze, size of members as per clause No. 8.20 (a) of SSR pt-1 complete all as specified and as directed by Engineer-in-Charge.

S & F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed by Engineer-in-Charge.

S & F in repair Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed by Engineer-in-Charge.

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S&F 300mm long aluminium alloy, anodised, sliding door bolt 12mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F mild steel spring for doors 300mm long, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by Engineer-in-Charge.

S&F 100 mm butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F Mild steel barrel tower bolts 200mm long, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F Mild steel pressed handles 150mm size, oval type, stove enamelled black complete all as specified and as directed.

S&F 300mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S & F in repair Floor door stopper 150mm length of cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specfied and as direcetd.

M&L 2nd class H/W plain fillets,rails, rafters, purlins, square, rectangular in section clean sawn secured with screws exc 13 sqcm but n exc 25 sqcm including dismantling timber as in fillets, rail, posts rafter, purlins etc under 40 sq.cm in section (unframed work) complete all as specified and as directed.

S & F 25 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 18-19 mm thick interior grade Prelaminated particle board, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including 6mm thick teak wood leeping as in cupboards, kitchen cabinet, pelmet box and similar work complete all as specified and as directed by Engineer-in-Charge.

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised for 40mm width of flaps complete all specified and as directed.

S & F in repairs Hasp and staple, safety type, 100 mm, anodised aluminium hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by Engineer-in-Charge.

S & F Factory made internal PVC door frame of size 50x47mm single revated made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed by Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 75mm long mild steel cold rolled medium weight butt hinges for door shutter and frames complete all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm long of extruded section with steel screws complete all as specified and as directed.

S&F for aluminium handles size 150 mm fabricated type anodised complete all as specified and as directed.

S & F aluminium powder coated window sliding type (3 track) with frame size 100x35x1.2mm thick and shutter frame size 39.40x17.70x1.2mm thick with and including two glass shutter and one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm thick tinted float glass and 0.36mm dia apperture 1.4mm SS wire mesh and fittings etc complete all as specified and as directed by Engineer-in-Charge.

M&L Machine cut cudappa stone slab 20-25mm thick as in steps, jambs, pillars, window- cills, cooking platforms and like over 15mm thick cement plaster in CM (1:4) and jointed in grey cement slurry mixed with pigment to match with shade of slab including rubbing, polishing and taking down existing cill/cooking platform complete all as specified and directed.

S & F aluminium louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc making to the jambs complete all as specified and as directed by Engineer-in-Charge.

S & F frame work such as grill, grating etc with ends bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors and similar work confirming to Fe 290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge.

M & L preparing old decorated plastered wall surfaces by using wire brush and jet spray and filling the cracks if any on the surface of wall by the crack sealent of approved make and applying two coats of water proof antifungal exterior acrylic emulsion paint (Apex Ultima protek) over coats of base/primer coat complete all as per manufacturers instructions and as directed by Engineer-in-Charge.(Note : (i) Rate of the crack sealent shall be deemed to included in the quoted rate of this item. (ii) Application of Acrylic emulsion paint strictly done by authorised applicator only.)

M&L for preparing new Steel Surfaces of any description, over 10cm in width or girth, not otherwise described and applying evenly two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces including all necessary preparation over 10 cms width or girth complete all as specified and as directed.

M & L for preparing of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applyinbg one coat of synthetic enamel paint any tint complete all as specified and as directed.

Removing old tar felt/ all loose dirt/ old roof tiles/ cement plaster and cleaning the concrete surface including removal of vegetation, fungus, moss small trees etc from the roof top with wire brush, including removing the strips of lightening conductor and refixing the same after repair work and applying neat cement slurry @ 1.5Kg/Sqm complete all as specified and directed by Engineer-in-Charge.

Demolition of lime Concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.

M & L for PCC 1:5:10 type E2 (using 40 mm graded stone agg) any thick as in sub base of sunken floor complete all as specified and as directed.

Supply & providing water proofing treatment with polymeric standard water proofing membrane, Aquaflex manufactured by M/s Bengal Bitumen, MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd/ Hyperplas manufactured by IWL Ltd having 10 years gurantee for water tightness complete all as specified and described as under:- (a) Preparation of sunken surface providing 10 mm thick rendering in cement mortar 1:4 mixed with WPC @ 2 % by weight of cement and applying one coat of polymeric modified bitumen 85/25 @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per manufaturer's specification complete all as specified and directed. (b) Supply & providing water proofing with polymeric proofing membrane of 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed. (c)GI pipe 40m bore light grade shall be embedded as outlet at the lowest portion for slope on the wall extending upto at least 450 mm beyond the outer wall.

Taking down cement plaster on brick or stone walls or concrete surfaces etc at any position including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M & L rendering 12 mm thick on concrete surfaces in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finishing top surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 5mm thick rendering on concrete surfaces of ceiling in CM (1:3) and rendering is to be finished even and smooth without using extra cement complete all as specificed and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for precast cement concrete block masonry of grade C-5 having density not less than 1800 kg/cum and 28 days average minimum compressive strngth of block should be 5 N/sqmm as in walling set in cement mortar 1:6 complete all as specified and as directed.

M & L preparing new plastered wall surfaces by applying 3mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L preparing old plastered wall surfaces and applying two coats of oil bound distemper over 3mm thick wall care putty to get smooth and even surfaces complete all as specified and as directed.

M&L for preparing new plastered surfaces of walls and applying evenly two coats of white wash complete all as specified and directed.

M&L for preparing old plastered surfaces of walls and applying evenly two coats of white wash complete all as specified and directed.

M & L for complete removal of existing treatment and preparation of old plastered or unplastered surfaces of wall and applying two coats of water proof cement base paint including Priming plastered and other surfaces with alkali resistant primer complete all as specified and directed by Engr-in-Charge (Make: Super snowcem plus/ Berger/ Asian/ shalimar.) Note:(i) Before applying cement base paint contractor shall use the wire brush and jet spray gun for the complete removal existing treatment and filling of crack using crack sealent. (ii) Application of cement base paint strictly done by spray/mechanical spray machine only.(iii) filling of cracks, holes and dents are includes in the same rates.’ (iv) Proper curing with water to be done before and after application of 1st coat.(v) In case of non adherance of above instructions 30% of cost recovery shall be made from accepted rate of the respective item.

M & L preparation of newly plastered surface of wall and applying two coats of water proof cement base paint over a coat of alkali resistant primer complete all as specified and directed. (Note : Curing of the Cement base paint shall be done as per the manufacturers instruction)

M&L for applying two coats of white wash on ceiling including preparation of newly plastered surfaces complete all as specificed and as directed.

M&L for applying one coats of white wash on ceiling including preparation of old painted plastered surfaces complete all as specificed and as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 m clear span, cills, steps seismic and other similar bands plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height copings, kneelers, apex stones, bed plates, kerbs, water troughs, benching in manhole half round shape and the like including weathering, slightly rounded or chamfered angles and throating, complete all as directed.

S & F Rotational moulded polyethylene water storage tanks 500 lts capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description in any position complete all as specified and as directed by Engineer in charge.

S&F in repair gun metal gate valve with iron wheel head, screwed both ends for iron pipes 20 mm bore complete all as specified and directed.

Taking up or down GI tubing 15mm bore and connections including removal to store complete all as specified and as directed by Engineer in charge.

Taking up or down GI tubing 20mm bore and connections including removal to store complete all as specified and as directed by Engineer in charge.

S & F GI tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer in charge.

S & F GI tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer in charge.

Refixing 15mm and 20mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

S&F in repair bib taps, long body with flange, cast copper alloy, chromium plated, fancy type screwed for 15mm bore of iron pipe or for brass ferrule complete all as per Prayag cat No. 8308 or technocommercialy equivalent in Jaquar or cera and directed

S & F in repair angular stop valves cast copper alloy, screwed down, high pressure with butterfly handle, screwed both ends for iron pipe or for unions 15mm bore complete all as per Prayag cat No. 8310 or technocommercialy equivalent in Jaquar or cera and as directed.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as per Prayag cat No. 8304 or technocommercialy equivalent in Jaquar or cera and as directed.

S&F in repair PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc complete all as specified and as directed.

S & F in repair stop valves cast copper alloy fancy type, chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe 15mm dia all as specified and directed.

S & F in repair CP brass shower rose 125 mm dia complete all as specified and as directed.

S&F in repair wash hand basin, flat back 450x300mm vitreous china (white) including PTMT waste fittings and PVC flexible waste pipe, 32mm bore size, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and as directed.

S&F in repairs Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including connection to trap and to flushing pipe, antisyphonage pipe complete all as specified and as directed.

S&F in repair kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers & wastes including CI cantilever bracket & connection union to pipe over all size 915mmx460mm & bowl size 410 x330x160mm complete all as specified and directed.

S&F in repair PVC floor trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S & F in repair towel rail 450 mm long of PTMT fixed with and including chromium plated brass screw and wooden / plastics cleats ( min wt 170 gms) complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs PVC (SWR) pipes, single socketed, 110mm bore in any length with rubber ring joints, fixed to walls etc complete all as specified and directed

S&F in repairs PVC (SWR) pipes, 75 mm bore, single socketed, in any length with rubber ring joints, fixed to walls etc complete all as specified and directed.

S&F in repairs PVC (SWR) bends of any radius, diminishing pieces or tapers 110 mm bore/dia complete all as specified and as directed.

S&F in repairs PVC (SWR) bends of any radius with access doors 75 mm bore/dia complete all as specified and as directed.

S&F in repair PVC (SWR) branch piece, single (single 'Y'), equal or unequal, 110mm bore/dia complete all as specified and as directed.

S&F in repair PVC (SWR) branch piece, single (single 'Y'),equal or unequal 75mm bore/dia complete all as specified and as directed.

S&F in repair PVC (SWR) junction single (Single 'T') equal or unequal, 75mm bore/dia complete all as specified and as directed.

S&F in repair PVC (SWR) junction single (Single 'T') equal or unequal, 100mm bore/dia complete all as specified and as directed.

S&F in repair 100mm bore/dia PVC vent cowl all as specified and directed.

S&F in repair 75mm bore/dia PVC vent cowl all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any cement mortar complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in base course complete all as specified and as directed.

M&L Matt finished coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L Matt finished ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm (400X400X7mm) in skirting, over 10mm thick rendering in CM 1:4 on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed.

M&L for non skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface 450 X 300 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10 mm thick cement plaster (1:4) complete all as specificed and as directed.

M & L for Machine cut kota stone slab flooring 20-25mm thick over and including 15mm thick cement screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engr in Charge.

M&L machine cut kota stone slab 20-25mm thick over and including 10mm thick backing coat of cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing as in skirting, vertical any type of surfaces, riser of steps including moulding where required complete all as specified and as directed.

S&F in repairs SS Curtain rod 25mm dia fancy type complete all as specified and directed.

S&F in repair decorative Knob stainless steel curtain rod brackets suitable for fixing of 25mm dia curtain roads including necessary fittings such as rawl plug and screws complete all as specified.

S&F in repairs Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified.

S&F in repair stainless steel glossy finish Soap dish fixed to plugs with chromium plated brass screws complete all as specified. (Make : Prayag cat No. BA-15S)

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L 75mm thick Plain Cement concrete (1:3:6) Type C-2 (using 40mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement complete all as as specified and as directed by Engr-in-Charge.

M & L for 100 mm thick PCC 1:4:8 type D2 (using 40 mm graded granite stone aggregate) in sub base complete all as specificed and as directed.

M&L for sand/stone dust filling under floor or in foundation or for cushioning of UG cable/ at cable trenches including watering and consolidation complete all as specificed and as directed.

M & L for Coloured Machine pressed glossy finished precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and no pigment laid over sand cushion complete all as specificed and as directed.(Make: NITCO/ Ultra Tiles/Topaz Tiles) Note: Contractor shall produce MTC & independent test certificate of paver block.)

M & L for preparation of old painted steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamal paint complete all as specified and directed.

M&L Black Marble (Bhaislana Zebra) 18 to 20 mm thick (table rubbed and polished ) as in steps, jambs, pillars, window- cills, and like over 15mm thick cement screed base in CM (1:4) including pointing with white cement (1:2) using marble dust with admixture pigment to match with shade of slab rubbing , polishing and rounding to edges including demolition of existing cill/cooking platform complete all as specified and directed.

M & L for point wiring complete with single core multi stranded FRLSH Copper conductor cable of size 1.5 sqmm PVC insulated unsheathed 1100 volt grade in and including PVC casing caping suitable dia with junction/ bends etc wall/roof /trusces and PVC switch board /hylam sheet of 3mm thick including M.S. boards of thickness 1.22 mm of suitable size for housing switched sockets etc including 1.5 sqmm green PVC FRLSH copper conductor for earth continuty incl dismantling taking down old unserviceable point wiring and making good to disturbed surfaces all as specified and directed.a) One light point controlled by one switch

Ditto all as per item No. 107 above but One light point controlled by two 2-way switch.

Ditto all as per item No. 107 above but One Fan/Exhaust fan point controlled by one switch.

Ditto all as per item No. 107 above but One three pin 5 Amp socket outlet with cables 1.5 sqmm on independent board.

Ditto all as per item No. 107 above but One three pin 5 Amp socket with cables 1.5 sq mm on same board.

Ditto all as per item No. 107 above but One bell point controlled by one switch

Ditto all as per item No. 107 above but with 2.5 sqmm cable insulated for 3 pin 15 Amp multipin socket outlet including 2.5 sqmm PVC insulated copper wire for earth continuity on independent board.

M & L for sub main wiring with 2 x 4 sqmm and 1x2.5 sqmm earth wire drawn in PVC casing caping of suitable size with accessories incl dismantling taking down old unserviceable point wiring and making good to disturbed surfaces all as specified and directed. Note :-(i) Two runs of cable and one run of earth wire & casing caping shall be measured and paid as one unit (RM).

S&F stepped type electronic fan regulator for ceiling fans including necessary connections of capacity 100 watts. 240 Volt incl dismantling taking down old unserviceable all as specified and directed.

S&F 5 Amp switch piano type single pole one way incl dismantling taking down old unserviceable all as specified and directed.

S&F 5 Amp Bell push flush types incl dismantling taking down old unserviceable all as specified and directed.

S&F 5 Amp switch piano type single pole two way incl dismantling taking down old unserviceable all as specified and directed.

Supply and fix socket outlet of 2 in 1 , 3 pin 5 amp incl dismantling taking down old unserviceable all as specified and directed.

Supply and fix switch socket combination multipurpose outlet comprising of 3 pin 15 amp socket out let & switch one pin, 5 amp controlled by one switch suitable for 3 pin plug top incl dismantling taking down old unserviceable all as specified and directed.

S&F ceiling rose surface PVC 65 x 50 mm two/three terminals incl dismantling taking down old unserviceable all as specified and directed.

S&F call bell electric, ding dong, AC 240 volt, 50 HZ. incl dismantling taking down unsv one all as specified and as directed. Make - Anchor or equivalent

S& F sheet metal enclosure for DBs SPN 8 Way double door type 230 Volts fixed incl dismantling taking down old unserviceable one all as specified and directed.

S&F in repair MCB, Single Pole, 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve all as specified and directed.

S&F in repair MCB, SPN 40 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve incl dismantling taking down old unserviceable one all as specified and directed.

S&F LED fitting, 20 watt, CDL, 230 Volts, 4 feet long , complete with all accssories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm twin core copper flexible conductor cable incl LED lamp and mounting casing box 2 nos incl dismantling taking down old unserviceable all as specified and directed. Make-CG, Cat Part No LCTLN-20-CDL or equivalemt in Bajaj/Philips/HPL/Havells

S&F LED fitting, 10 watt, CDL, 230 Volts, 2 feet long , complete with all accssories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm twin core copper flexible conductor cable incl LED lamp and mounting casing bo x 2 nos incl dismantling taking down old unserviceable all as specified and directed.. Make-CG, Cat Part No LCTLN-10-CDL or equivalemt in Bajaj/Philips/Wipro/Havells

S&F lamp Holder insulated body with back plate for batten/angle incl dismantling taking down old unserviceable all as specified and directed.

S&F LED Lamp 9 watt (B-22) pin type incl dismantling taking down old unserviceable all as specified and directed. Make :- CG Cat Part No LED 9W -B22/E27-CDL/WWor equivalemt in Bajaj/Philips/Wipro/Havells

S&F LED type Bldg light fitting 15W with cast aluminium with necessary brackets and clamps nut bolts etc incl dismantling taking down old unserviceable all as specified and directed. Make : Bajaj/ CG/Philips/Wipro

S&F MCB DB double door ETPN 4 way with 200 Amps rated bus bar 240 volts incl dismantling taking down old unserviceable all as specified and directed.

S&F MCB TPN 40 Amps, 415 volt 10 KA incl dismantling taking down old unserviceable all as specified and directed.

REPAIR TO CEILING FANS WITH FOLLOWING ITEMS OF WORK :- M&L for Rewinding of Ceiling fan 1200/1400 mm sweep after dismenting complete motor assy, bearings, bushings, removal of burnt copper wire, cleaning of core, inserting proper insulating paper in slots, winding with and as per existing size/turn of super enamelled copper wire, heating, vernishing, replacement of unsv bearings / bushings, assemble of rotor and stator unit with capacitor, connecting wire, down rod, blades and testing complete. Note: 1. Contractor will collect fans from the complaint cells of specified area and bring back to complaint cell after repair. Cost of transportation will be inclusive of quoted rate. 2. Spares require for replacement such as bearing, Bushing, capacitor shall be measured and paid separately as supply & Fixing only. 3. Cost of Connector bock and capacitor holder shall be inclusive of the quoted rate.

All as per above Item No 133 but Exhaust Fan 280/300mm sweep size.

S&F ball bearing No 6201/6202/6203/6204 of SKF/Tata/NBC.

S&F G.M. Bush bearing for ceiling fan as per existing pattern.

S&F capacitor AC for 230 volts 50 Hz of capacity 2.0/2.25/2.5 Mfd.

Painting of ceiling fan 1200/1400 mm including scrapping, cleaning and removing dust from the blade an body and applying two coat of enamel paint over & one coat of primer all as directed by engr-in-chage

Supply, laying and testing of UG cable, XLPE insulated, screened, PVC bedded galvanised steel strip or wire, armoured, electric power cable (heavy duty) with stranded aluminium conductor, 1100 volts grade of size 16 sqmm 4 core including taking down the existing unserviceable cable complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep and getting out complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of pipe and getting out in soft disintegrated rock.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm thick in soil complete all as directed.

Removing excavated surplus soil not exc 50 m and depositing where directed at level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for brick protection with old size sub-class bricks ‘B’ Designation 75 for UG cable.

M & L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified bldg), connected with galvanised steel earthing lead of 4mm dia all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2with RCC precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia MS rod, funnel, wiremesh, 15 mm dia light grade GI tubing for protection of GI wire 4mm dia, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion.

Veekay Enterprises

M/S JAYCONSTRUCTION CO

V.R.PRAJAPATI AND CO.

S.R.M.K Enterprises