CWE/CHM-107/2025-26 REPAIR TO CERTAIN INTERNAL ROADS IN OTM AND MD ACCN AREA UNDER GE CHANDIMANDIR

Amount

Preparation of black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc complete all as specifed and directed by Engineer-in-Charge.

Applying evenly a tack coat of Cationic Bitumen Emulsion (RS-1) conforming to IS: 8887 at a rate of application of 0.2-0.3 kg/sqm on bitumenous surface as specified in Table 500-5 of MoRT&H specification for road and bridge works 2013, using mechanical sprayer after cleaning of existing surface complete all as specifed and directed by Engineer-in-Charge.

M&L for Scarifying or picking gravelled, macadam or bitumenous macadam surfaces in area not exc 400 sqm and exceeding 50mm and not exc 100 mm deep complete all as specified and as directed by Engineer-in-charge.

Applying evenly a prime coat of Cationic Bitumen Emulsion SS1 confirming to IS: 8887 at a rate of application of 0.7 - 1 kg/sqm on surface of WMM/ WBM as specified in Table 500-3 of MoRT&H specification for road and bridge works 2013, using mechanical sprayer complete all as specifed and directed by Engineer-in-Charge.

M&L for Bitumenous concrete (BC) 30 mm thick (consolidated thickness) layer confirming to clause 507 of MORT&H specifications for road and bridge work (Fifth Revision) including cost of coarse aggregates, fine aggregates, filler with 5.4 % binder (VG-30) contents by weight of total mix, crushed aggregate of grading 2, anti stripping agent, warm mix additives (quantity, quality and grade as per the approved job mix formula) etc, cleaning and pre-heating of the mineral aggregate, filler & bitumen of specific temperature throughly mixing with binder of specified bitumen contact, anti stripping agent, warm mix additives as per mix design in hot mix plant (batch type) of 100-120 TPH capacity, carrying the hot mixed materials by means of tipper, trucks or any other approved and and suitable arrangements, laying and hot premixed materials over the prepared surface by means of paver finisher ......Contd..

Contd.. including manual operation as and when required for proper grade, including level and camber through rolling with power roller 8 to 12 tonnes smooth wheeled, vibratory and tendom roller with necessary hand packing and pinning to give an even surface including running expense of all plants and machineries, inclusive of proper traffic control during laying to the satisfaction of Engineer-in-charge, required quality control tests at required interval etc complete in all respects complete all as specified and as directed by Engineer-in-Charge. Notes : (i) Job Mix formula as per clause No. 505.3.3 of MORT&H specification for road and bridge work (Fifth Revision) for bituminous concrete shall be got designed from NIT/CTL/Govt Engg Collage and shall be got approved from GE in writing well before commencement of work without any financial effect to the department. Also the bitumen content shall not be less than 5.4 % by weight of total mix as per clause 507.2.5 of MoRT&H specifications (Fifth Revision).

M&L for Providing, laying & Compaction of bituminious, macadam (BM) compacted thickness not exceeding 75 mm thick conforming to clause 504 of MoRT&H specification for road and bridges works (Fifth Revision) using mechanically crushed stone aggregates and granual material etc of grading II as per Table 500-7 of MoRT&H specification for Road and Bridges work (Fifth revision) Premixed with bituminious binder bitumen grade VG-30 @3.4% (percent by weight of total mix) prepared in batch type Hot Mix Plant transported to site by tippers, laid over a previously prepared surface with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density complete all as specified and directed by Engineer-in-charge.

Notes : (i) Mix Design for Bituminous macadam shall be got designed from NIT/ CTL/ Govt Engg College and shall be got approved from GE in writing well before commencement of work without any financial effect to the department. Also the bitumen content shall not be less than 3.4% by weight of total mix as per clause 504.2.4 of MoRT&H specifications (Fifth Revision). (ii) If qty of binder contents is less than the qty as specified in respective items of BOQ, it shall be adjusted at supply only rates of paving bitumen @ Rs. 55.00 Per KG and if qty of binder contents is more than the qty as specified is respective items of BOQ no adjustment shall be made.

Repair to potholes any depth, not exceeding 1 sqm each including sweeping free from dust and mud, or water, scouring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by applying tack coat at 5 kg per 10 sq m. putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 kg per 10 sqm, blinded with 0.09 cum of stone chippings, 6.3 mm size and again well rammed (including supply or premixed macadam, binder and chippings), depth of potholes not exceeding 30 mm complete all as specified and as directed by Engineer-in-charge.

M&L for 2.5 mm thick, white/ yellow hot thermoplastic road marking paint, conforming to BS standards 3262 with 20% of glass beads (intermixed) spread and laid by automatic mechnical engine driven machine, painting as in strips (continuous or breaking) of width not exceeding 10 cm complete all as specified and as directed by Engineer-in-charge.

Supply and fix in repair solar cat eye/solar stud, aluminum alloy shell (100% water proofing design of size 125 mm x 125 mm x 25 mm (shank 65 mm) of high efficiency Mono crystaline solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufacturer's instructions etc. complete all as specified and as directed by Engineer-in-charge.

Supply and fixing cat eye, solar reflective type, of metal body alloy of size 100 mm x 100 mm x 20 mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufacturer's instructions complete all as specified and as directed by Engineer-in-charge.

Supply and fixing solar road Delineator having LEDs of colours red/green, solar cell, battery and light sensor housed in a Plastic Body, well protected with powder coated anti theft wire mesh cage, LEDs shall be multifunction (flash-stable-close), system workable for 2-3 days (night) after full charge in 8-10 hours, system mounted over 50/ 60 mm dia powder coated steel tube of length 1000 mm having sheet foot for firm grip to ground, including embedding in PCC Block (size 150 x 150 x 300 mm) 1:2:4 type B-1 including necessary excavation work in post holes complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement Concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.

M&L 100 mm thick PCC 1:4:8, type D-2 (using 40 mm graded stone aggregates) as in sub base, finished even and rough without using extra cement complete all as specified and as directed by Engineer-in-charge.

Providing and laying 40 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed by Engineer-in-charge.

Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed by Engineer-in-charge.

Providing and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed by Engineer-in-charge.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed by Engineer-in-charge.

Material and labour for preparation of new concrete surfaces Exceeding 10 cm in width & girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old concrete surfaces exceeding 10 cm in width or girth and appplying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-charge.

S&F in repair convex mirror minimum 100 cm in dia outdoor type, body material- Polycarbonate, acrylic and mirror thickness not less than 3 mm for traffic security purpose mounted on 2 metre long SS pipe Gde 30G fixed with nut bolt and adjustable brackets/ clamps system including necessary excavation and embeded in cement concrete 1:2:4, type B1 (using 20 mm graded crushed stone aggregates) complete all as specified and as directed by Engineer-in-charge.

S&F retro reflective sheeting for sign board (face to be fully covered) with high intensity prismatic (type-IV) sheeting conforming to type III of ASTM-D 4956-01 as approved by Engineer-in-Charge with letters, boarders etc. as ordered as per IRC: 67-2001 in silver white with blue/ green or any other colour background, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II ASTM-D-1956-01 complete all as specified and as directed by Engineer-in-Charge. Note: ACP Sheet and MS/ SS structural framework will be measured and paid separately under relevant items of this schedule.

M&L for stainless steel (Grade 304) structural work for road sign board, any type, fabricated out of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing as required including excavaion in post holes and grouting the frame in ground, filling with cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) including demolition of existing MS frame etc. complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium Composite Panel (ACP) Sheet, 4 mm thick for sign Board and fixing the same to the MS/ SS structural frame work by means of suitable sized alluminium alloy/ SS rivets or bolts and nuts etc., complete all as specified and as directed by Engineer-in-Charge. Note: MS/ SS structural framework and retro reflective sheet will be measured and paid separately under relevant items of this schedule.

M&L cement concrete type D2 1:4:8 (40mm graded aggregate) in foundations, filling to kerb stone etc. complete all as specified and directed by Engineer-in-charge.

numac powertech (BID ID -3470835)

K L Kataria and Sons (BID ID -3474431)

PAWAN KUMAR (BID ID -3474533)

shree balaji builders (BID ID -3474585)