REPAIR/REPLACEMENT OF PUMPS SETS MOTORS CERTAIN CONNECTED E/M WORKS TO WATER/SEWAGE SUPPLY INSTALLATION UNDER AGE E/M (W) OF GE (W ) AGRA

Amount

Checking of LT Panel/Motor/Pump set for detecting any kind of fault and attending the fault immediately at any time round the clock and carry out certain repairs required as per site requirement and replacing of worn out parts by expert engineer complete all as direced. Note :- Unit rate includes detecting of any kind of fault in LT Panel/Motor/Pump set only and cost of replacement of worn out parts shall be measured and paid separately under respective items of BOQ

Supply and fix in replacement Direct online starter for 3HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54, 230 Volt, Single Phase, Extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge.

Supply and fix in replacement Direct online starter for 5HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge.

All as pr item No 3 above but 7.5 HP

Supply and fix in replacement fully automatic star delta starter for 10 HP submersible pump, confirming to IS/ IEC 60947-4-1, IP-54,415 Volt, extended wide band coil with FRLS internal wiring, star type-Air break and class H insulation complete all as specified and directed by engr-in-charge.

All as per item No 5 above but 12.5 HP

All as per item No 5 above but 15 HP

All as per item No 5 above but 20 HP

All as per item No 5 above but 25 HP

Supply and fix in replacement 3 Pole Power contractors with AC coil, rating 18 Amps, conforming IS/ IEC 60947-4-1, IP-20,415 Volt, snap fit construction, nut retaining washer for quick termination and class H insulation complete all as specified and directed by engr-in-charge.

All as per item No 10 above but 25 Amp

All as per item No 10 above but 32 Amp

All as per item No 10 above but 150 Amp

All as per item No 10 above but 185 Amp

S&F in repair thermal over load relay type MN suitable for MNX contactors relay range 90-150 Amps including fixing arrangement complete all as specified and directed.

All as per item No 15 above but 9 to 15 Amps

All as per item No 15 above but 22 to 32 Amps

Supply & Lowering commissiong and testing only of submersible pump set three phase, 415 Volts, capacity 12.5 HP and discharge head 75 Mtrs complete all as specified and directed.

Supply & Lowering commissiong and testing only of submersible pump set three phase, 230 Volts, Single Phase, Capacity 2 HP and discharge head 30 Mtrs complete all as specified and directed.

Dismantling of defective submersible pump set 10-15 HP with column assembly, pump bowl assembly of any size/capacity including disconnecting electrical and water line connection complete with lifting it with the help of chain pulley, clamp tripod and reassembling after repairing by lathe work and other machinery work as required and replacement of studs, nuts, bolts etc including re-fixing the same after making it serviceable in its existing position complete all as specified and directed.

All as per item No 20 above but pump set capacity 5 to 7.5 HP

All as per item No 20 above but pump set capacity 1 to 3 HP. Note (i) Defective spares for pump and column assembly shall be measured and paid separately under respective item here-in-after. (ii) After taking out submersible pump set for repair the contractor shall cover tube will with cap to avoid any accident. (ii) Defective spare parts of bowl assembly shall be measured and paid separately under items here-in-after.

Supply only the Gun Metal Impeller parts of submersible pump bowl assembly suitable for 10 to 15 HP complete all as directed

Supply only the Intermediate bowl parts of submersible pump bowl assembly suitable for 10 to 15 HP complete all as directed

Supply only the Bowl bush rubber parts of submersible pump bowl assembly suitable for 10 to 15 HP complete all as directed

Supply only the Bowl bush (Gun metal) parts of submersible pump bowl assembly suitable for 10 to 15 HP complete all as directed

Supply only the Cast iron impeller seal ring (neck ring) parts of submersible pump bowl assembly suitable for 10 to 15 HP complete all as directed

Supply only the Stainless steel running sleeve (Off sizes) parts of submersible pump bowl assembly suitable for 10 to 15 HP complete all as directed

Supply only the Pump shaft 25.4mm dia parts of submersible pump bowl assembly suitable for 10 to 15 HP complete all as directed

Supply only the CI Impeller parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as directed

Supply only the Intermediate bowl parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as directed

Supply only the Bowl bush rubber parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as directed

Supply only the Bowl bush (gun metal) parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as directed

Supply only the Cast iron impellor seal ring (neck ring) parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as directed

Supply only the Stainless steel running sleeve (off size) parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as directed

Supply only the Impellor locking keys stainless steel (off size) parts of submersible pump bowl assembly suitable for 5 to 7.5 HP complete all as directed

Supply only the PVC impellor parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as directed

Supply only the Intermediate bowl parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as directed

Supply only the Bowl bush rubber parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as directed

Supply only the Bowl bush (gun metal) parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as directed

Supply only the Cast iron impellor seal ring (neck ring) parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as directed

Supply only the Stainless steel runnig sleeve (Off size) parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as directed

Supply only the Impellor locking keys stainless steel (Off size) parts of submersible pump bowl assembly suitable for 1 to 3 HP complete all as directed

Dismantling of 01 to 03 HP Capacity defective submersible motor any make, cutting and taking out burnt out winding wire and M&L for rewinding the same with PVC insulated water proof conductor copper wire of best quality of existing gauge & turn and reassembling after replacement of bush, bearing, sleeves, grinding as required and polishing of rotor shaft etc including testing and refixing the same in existing position complete all as specified and directed. Note : Bush/bearing/sleeve/thrust plate shall be measured and paid separately under respective item here-in-after.

All as per item No 44 above but for 05 to 7.5 HP capacity

All as per item No 44 above but for 10 to 12.5 HP capacity

All as per item No 44 above but for 15 HP capacity

Supply only the Bush/bearing of suitable size (gun metal) suitable for 01-03 HP parts for the submersible motor all as directed.

All as per item No 48 above but 05/7.5 HP .

All as per item No 48 above but 10/12.5 HP .

All as per item No 48 above but 15 HP .

Supply only the Thrust Plate of suitable size (gun metal) suitable for 01-03 HP parts for the submersible motor all as directed.

All as per item No 52 above but 5/7.5 HP .

All as per item No 52 above but 10/12.5 HP.

All as per item No 52 above but 15 HP.

S&F in repairs submersible cable PVC insulated copper conductor 2.5 Sqmm 3 core 1100 volts grade complete all as specified and directed

All as per item No 56 above but 4 Sqmm.

All as per item No 56 above but 6 Sqmm.

M&L for 80mm bore, adopter nipple 50cm long GI flanged or socketed (for connecting column pipe to pump) complete all as specified and directed.

All as per item No 59 above but 100mm bore.

M&L for coupler for pump and motor of any capacity (submersible pump) complete all as specified and directed .

M&L for motor housing studs of any size complete all as specified and directed.

S&F Cast iron non return valve of size 100 mm bore, ISI marked both ends flanged including rubber gasket, MS bolts, nuts, washers and tersting complete all as specified and directed.

All as per item No 63 above but 80 mm bore.

Supply and packing pea gravel of 02 mm to to 06 mm size of the appoved quality as ordered to pack around the casing / slotted pipes in bore well complete all as specified and directed.

Developing tube wells by compressed air with minimum pressure of 10kg/Sqcm and minimum air discharge 450 CFM all as specified in IS 11189-1985 Para 4.3 complete all as specified and directed. Note : Compressor, pump, pipe and other allied items will be arranged by contractor and no extra payment will made by the department.

S&F MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA

S&F MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA

S&F MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA

S&F in repair single phase preventor for protection for submersible pump against over loading, reverse phase, single phasing complete all as specified and directed.

Taking up centrifugal pump set from its foundation at different location of installations by disconnecting electrically and machnically, transporting it to the workshop for dismantling the pump sets and back to installation after repairing/removing of unserviceable parts.

(a) 150 HP Capacity

(b) 100/120 HP Capacity

(c) 30 HP Capacity

(d) 15 to 20 HP

(e) 10/12.5 Capacity

(f) upto 5 Hp Capacity

M & L for re-winding of electric motor of centrifugal pump sets 3 phase 415 volts 50 Hz AC with super enamelled copper winding wire of existing weight & size incl cleaning of stator slot winding paper fixing startor incl cut x size warnshing and baking complete all as specified & directed by Engr-in-Charge for capacity :-

(a) 150 HP Capacity

(b) 100/120 HP Capacity

(c) 30 HP Capacity

(d) 15 to 20 HP

(d) 10/12.5 Capacity

(e) upto 5 Hp Capacity

Repairing of rotor assembly of centrifugal motor sets 3 phase 415 volts 50 Hz AC including dismantling and reassmbled at site complete all as specified & directed by Engr-in-Charge for capacity.

(a) 150 HP Capacity

(b) 100/120 HP Capacity

(c) 30 HP Capacity

(d) 10/12.5 Capacity

(e) upto 5 Hp Capacity

M&L painting of centrifugal pump set complete all as specified and directed by Engr - in - Charge including painting of SM No. and MES No. on the pump set for the capacity:-

(a) 150 HP Capacity

(b) 100/120 HP Capacity

(c) 30 HP Capacity

(d) 10/12.5 Capacity

(e) upto 5 Hp Capacity

Repairing/overhauling of centrifugal pump set incl cleaning of inside motor & pump set. Oiling greshing, gland packing filling and proper allignment incl repair/replacement of wear & tear are unserviceable part for

(a) 150 HP Capacity

(b) 100/120 HP Capacity

(c) 30 HP Capacity

(d) 15 to 20 HP

(d) 10/12.5 Capacity

(e) upto 5 Hp Capacity

Centrifugal pump set spare suitable for 150 HP pump set

(a) Ball bearing for motor of existing size

(b) Ball bearing pump set of existing size

(c) Roller bearing for pump set size

(d) Impeller made out of existing size

(e) Glands bush

(f) Neck Ring

(g) Cuppling complete of existing size

(h) Pump shaft incl key

(j) Rubber bush incl nut bolt and washer complete

Centrifugal pump set spare suitable for 100/120 HP pump set

(a) Ball bearing of motor of existing size

(b) Ball bearing pump set of existing size

(c) Roller bearing for pump set size

(d) Impeller made out of existing size

(e) Glands bush

(f) Neck Ring

(g) Cuppling complete of existing size

(h) Pump shaft incl key

(j) Rubber bush incl nut bolt and washer complete

S&F Centrifugal pump set spares suitable for 30 HP

(a) Ball bearing for motor of existing size

(b) Ball bearing pump set of existing size

(c) Impeller made out of brass of existing size

(d) Glands bush

(e) Neck Ring

(g) Cuppling complete of existing size

(h) Pump shaft incl key

(j) Rubber bush incl nut bolt and washer complete

S&F Centrifugal pump set spares suitable for 15-20 HP

(a) Ball bearing for motor of existing size

(b) Ball bearing pump set of existing size

(c) Impeller made out of brass of existing size

(d) Glands bush

(e) Neck Ring

(g) Cuppling complete of existing size

(h) Pump shaft incl key

(j) Rubber bush incl nut bolt and washer complete

S&F Centrifugal pump set spares suitable for 10/12.5 HP (Mono block)

(a) Ball bearing pump set of existing sizes and make.

(b) Impeller made out of CI of existing size

(c) Glands bush

(d) Neck Ring

(e) Coupling complete

(f) Pump shaft incl key

(g) Rubber bush incl nut bolt and washer complete

S&F Centrifugal pump set spares suitable for upto 5 HP (Mono block)

(a) Ball bearing of pump set of existing sizes and make.

(b) Impeller made out of CI of existing size

(c) Glands bush

(d) Neck Ring

(e) Coupling complete

(f) Pump shaft incl key

(g) Rubber bush incl nut bolt and washer complete

Material and labour for column pipe GI 'C' class for borewell 2" dia including threading and all connected works all as directed by Engr-in-Charge. Taking up of motor and lowering will be measured seperately.

Material and labour for column pipe GI 'C' class for borewell 3" dia including threading and all connected works all as directed by Engr-in-Charge. Taking up of motor and lowering will be measured seperately.

Taking out and dismantling of defective jockey pump set of 12.5 HP (Capacity 10.8 Cum/Hr Cap) with column assembly, pump bowl assembly, gun metal impeller , intermediate Bowl, Ci impeller (neck ring), Bowl bush rubber,/Gun metal etc parts including disconnecting electric and water line connection complete with lifting it with the help of chain pulley, clamp tripod and reassembling after repairing buy the laith work and other machinery work as required and replacement of studs, nuts bolts and defected parts etc including re-fixing the same after making it serviceable in its existing position complete all as specified and directed by Engr-in-Charge.

M&L for PCC (1:4:8) type D-2 (using 40mm stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

Asha Construction

rohan traders

M/S Solanki Brothers

C P Singh and Co

Balaji Associates

M/S RAJESH ENTERPRISES

M/s S.M. Construction