REPAIR TO CGI SHEETS GALVAUME SHEETS FALSE CEILING AND MISC WORKS AT DALHOUSIE CANTT

Amount

Dismantling plain or corrugated steel sheeting any gauge, thickness, including naintal or similar pattern roof coverings.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating 275 all complete as specified and directed.

S&F 0.80mm thick plain, galvanised, mild steel sheeting in ridges, hips, valley gutters, drip & straight flashins (length and girth as fixed) having zinc coating @ 120 gm/sqm fixed with 'L' type or 'J' type or cranked hook bolt complete as directed.

Ditto as per srl item 2 and 3 but Except sheeting (any Thickness) and all as specified and as directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. (Make TATA or JSW)

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets as directed.

8mm thick non asbestos fibre cement designer board ISI Marked fixed with screw to aluminium frame work in ceiling flat or sloppy as per manufacturer instructions

Ditto as per Serial Item No. 08.00 except non asbestos building boards

S&F Anodised aluminium snap grid frame work for false ceiling for size of grid 605 x 605 mm including hangers 6 mm dia GI (up to 1200 mm long) adjusting level fixed to roof complete all as specified

Preparation of old painted steel surfaces (such as CGI sheet, Window grill ,GI water tube, fencing post etc.) and applying two coat of synthetic enamel paint complete all as specified

Dismantling timber scantling 40sqcm and over in section in any position in framed work all as specified.

M&L for second class hardwood in scantlings in framed work and fixed clean sawn etc all as specified.

S&F structural steel work as in roof trusses (framed), trussed, purlins, rafter, crane gantries, rails & fastenings & heavy brackets framing including distance pieces, cleats etc. confirming to Fe 410-W (E-250 grade quality A).

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates including bending and welding.

Dismantling wrought iron or mild steel work of any description not other wise provided.

S& F mild steel flat iron 40x5 mm for wind tie confirming to Fe 410-0 or Fe 310-o

Dismantling mild steel work of any description not otherwise provided for as in wind ties and fixing in same position

Demolition of stone/brick masonary built in cement/cement lime mortar.

M&L walling of random rubble stone masonery brought up to course, well bonded,bedded and solidly hearted, built in CM 1:6.

M&L walling of random rubble stone masonery brought up to course, well bonded,bedded and solidly hearted, built in CM 1:6. but Except stone.

M & L rendering 15mm thick on stone masonry surfaces or surfaces other than fair faces of brick work in CM 1:4, finished even and smooth without using extra cement.

Preparation of new steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide all as specified

M & L for two coats white wash on walls on plastered surfaces as preparatory work on newly plastered surfaces.

m/S Varun Gupta

M/S WALIA ENGINEERS