Construction of Sub Health Center at village Kutani in District Panipat. (Re-Invited)

Amount

Earth work in excavation in foundations, trenches etc. in all kinds of soils, not exceeding 2 mtr depth including dressing of bottom & sides of trenches etc, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction, including disposal of all surplus soil as directed within a lead of 30 meters. (HSR 6.6)

Earth filling under floors with surplus soil, excavated from foundation and taken only from outside the building plinth, in 15cm layer including ramming watering and consolidating lead upto 30 metres (HSR 6.13(a)) a) with surplus soil

Cement concrete 1:8:16 with brick ballast 40mm nominal size in foundation and plinth(HSR 10.26).

Cement concrete 1:1-1/2 : 3 with stone aggregate 20mm nominal size for reinforced concrete work in footings, strips, foundations, beams rafts, pedestals and approach slabs of bridges etc, excluding steel reinforcement and including centring and shuttering, laid in position, complete in all respects, (For work up to 1.5 metres below ground level) (HSR 10.90+10.95 (a))

First class brick work laid in cement sand mortar 1:6 in foundation and plinth ( HSR 11.2)

11.43 cm thick brick wall laid in cement sand mortar 1:4 without reinforcement in foundation and plinth (HSR 11.47)

Damp proof course 40mm thick of cement concrete 1:2:4 using stone aggregate 20mm nominal size with 2 coats of bitumen 20/30 penetration at 1.65 kg per sqm laid hot and sanded.(HSR 10.114)

First class brick work laid in cement sand mortar 1:6 in first storey up to 4 metres above plinth level.(HSR 11.7)

2nd storey.

11.43 cm thick brick wall laid in cement sand mortar 1:4 in superstructure.(HSR 11.48a)

Cement concrete 1:1 1/2:3 with stone aggregates 20mm nominal size for RCC work in slabs not exceeding 25 degree inclination horizontal centring shuttering and laid in position complete in all respects.(HSR 10.82+10.95(a))

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20cm thickness (straight and curved) beams, girders, stairs, columns, (square or rectangular) battens and lintels etc. excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects. (HSR 10.86)

Cement concrete 1:1 1/2:3 with stone aggregate 20mm nominal size for reinforced concrete work in fascias parapets and other thin vertical sections, not covered by Item nos. 10.82, 10.86 to 10.88 not exceeding 10 cm thickness excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects.(HSR 10.89+10.95(a))

Cement concrete 1:2:4 with stone aggregate 20mm nominal size for reinforced concrete work, in shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects.(HSR 10.81)

Terracing consisting of tiles 22.86cm x 11.43 cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25mm mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc.(HSR 13.13)

Providing and embedding 100mm dia. H.C.I. Rain water without ears I.S.I. Mark pipe in cement mortar during masonry work.(HSR 13.43)

providing and fixing C.I. plain bends in position with gutter, etc. (a) for 100mm dia pipe(HSR 13.49(a))

Top khura 0.6x0.6m for rain water pipe in 25mm thick Cement concrete 1:2:4 over 50mm thick. Cement concrete 1:8:16(HSR 13.50)

Bottom khurra on ground 1.2mx0.6m consisting of brick on edge laid cement mortar 1:3 over 75mm cement concerete 1:8:16 including 12mm thick cement plaster (HSR 13.57)

Cement concrete 1:2:4 gola 10cm x 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR 13.64)

Base course of floor consisting of 100mm thick cement Concrete 1:8:16 and 100mm sand or stone filling (HSR 14.1)`

Conglomerate floor 25mm thick cement concrete 1:2:4 on 100 mm cement concrete 1:8:16 and 100mm sand or stone filling (HSR 14.11)

Providing and fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. (14.89)

Providing and fixing vitrified tiles of size 600x600 mm of approved make in Skirting/dado laid in any patternass pecified overbase of 20mm thick cement coarses and mortar 1:3 and jointed with white cements lurry mixed with pigment to match the shade to tiles.(HSR 14.90)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facture) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting risers of steps and dado over 2 mm thick bed of cement mortar 1:3 coarse and jointed wtih grey cement slurry, including pointing in white cement mixed with pigment of matching shades b) Size of Ceramic Glazed tile 300 x 450 mm (H.S.R. 14.92 (b)).

Kotah stone flooring 34mm to 40mm thick in any pattern as specified over 12mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing.(HSR 14.62)

Kotah stone 20mm thick in skirting risers of steps, dados and wall facing (lining) and pillars laid on 12mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pins etc.(HSR 14.66)

Providing and fixing glass strips, 4 mm thick in floors. a) 40mm wide (HSR 14.79(a))

25mm wide.

Pdg. & fixing carriage tiles/ anti skid tiles of size 400mm x 400mm of approved make in flooring lain in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry with pigment to match the shade to tiles. Note:- Tile shall be premium quality (first quality) of reputed manufacture like: NITCO, KAJARIA, SOMANI, ORIENT, BELL, JHONSON & RAK AND SIMPOLO existing items of chapter 13 of HSR (Hoisting and Roofing), the nomenclature No. 13.92, 13.93 has been amended as under: (HSR 14.91)

10mm thick cement plaster 1:3(HSR 15.46)

12mm thick cement plaster 1:6 (HSR 15.7)

15mm thick cement plaster 1:6 on the rough side of single or half brick wall.(HSR 15.12)

(b)2nd storey.

10mm thick cement plaster 1:4 under ceiling (HSR 15.52)

Factory manufactured solid flush door shutters, with block board core as per IS 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to IS 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops, etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.(HSR 17.93) i) 25mm thick

ii) 35mm thick

Factory manufactured wire gauge door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash etc (non coniferous timber other teak conforming to IS specification no.1003 kiln seasoned) with 100mm wide vertical style , 150 mm wide lock rail 200mm wide bottom rail and wire gauze of 140 G or 120G designation including cost of iron hinges,screws,chock/cleats,stops nails etc.complete fixed in position (excluding the cost of any fittings other than specified above but including labour for fixing the same in position.(styles and rails of windows shutter shall be 75mm wide) (ii) 35mm thick (HSR 17.92(ii))

Cost of iron fittings, complete for doors and windows, such as tower bolts, handles,etc, and screws for these fittings(excluding sliding bolt) a) for single leaf shutter(HSR 17.72(a))

Providing and fixing 150mm hasps and staples with necessary screws, etc., complete. c) iron(HSR 17.78(c))

Providing and fixing helical door spring 150 mm (superior quality), including necessary screws, complete.(HSR 17.79 B) iron.

Providing and fixing sliding bolt with nuts and screws, etc.complete. (c) iron ii) size 250mmx 16mm(HSR 17.83 ( c )

Providing and fixing 0.50 mm thick aluminium sheet, including cost of necessary screws etc., complete(HSR 17.87)

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete.(HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc.(HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.(HSR 16.3)

Applying priming coat with metal primer on new steel or iron work including preparation of surface.(HSR 16.9)

Painting two coats excluding priming coat with ready mixed paint for metallic surfaces in all shades on new steel or iron work (HSR 16.17)

Distempering with washable oil bound distemper (of approved manufacture) two coats excluding priming coat on new work (HSR 16.57)

Pdg. two coats of exterior acrylic emulsion paint on new work (as per new item HSR 16.79)

Providing and Applying two coats white cement based putty over plastered surface and grinding the surface smoothwith sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K. / Birla make) (HSR 16.81)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces (HSR 16.25)

Wrought iron and mild steel (using angles, flats, square bars, tee and channels) ladders, grills, gratting frames, windows guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position.(HSR 18.12)

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22)

Providing and fixing hard drawn steel wire fabric 75mm x 25mm rectangular mesh with 3.25mm dia wire fixed on steel windows of standard rolled sections with 3 mm thick flat iron cover moulding of 12.5 mm width fixed with machine screws welded complete in all respect.(HSR 18.33)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete:- door and window frame of size 76 mm x 38 mm with 35 mm wide single rebate. (HSR 18.34)

(c ) Door and window frame of size 127mm x 50mm with 40 mm wide single rebate.

Precast chequered tiles of 20mm thickness in ordinary grey cement without chips laid on 20mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings.(HSR 14.45)

Providing and laying Baroda Green Marble stone 17mm and above thick flooring included matching the grains of Marble slab in any pattern as specified laid over 12mm thick cement sand mortor 1:3 and joint with white slurry mixed with pigment to match the shade of marble including rubbing and polishing. The rates are for all heights/storey. The sample shall be got approved from Engineer-in-Charge (HSR 14.99)

Parking and approach road

Constructing of 6'-0'' high 9" thick boundary wall of standard size.

Provision for providing and fixing steel gate complete in all respect. Earth filling in campus of Suh Health Centre with an avg. lead 1 Km i/c watering and ramming as per PWD specification. The final payment/ quantity should be given as per level X-section.

Public Health Work Providing and fixing PVC Rain water pipe 6kg pressure of ISI mark in Cement mortar during masonry work (HSR 13.89) (a) 100 mm Dia PVC pipe 6 Kg pressure.

(b) 150 mm Dia PVC pipe 6 Kg pressure.

Providing and fixing PVC Bend ISI Mark (HSR 13.90) (a) 100 mm dia PVC Bend

(b) 150 mm dia PVC Bend

CONSTRUCTION BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 BENCHING 12mm THICK CEMENT PLASTER 1:2 with a floating coat of 1mm thick of neat cement R.C.C.1:2:4 SLAB 100mm THICK /C.C.TOPPING 50 mm THICK WITH 455 MMx455MM/ 455 MM x610MM INSIDE LIGHT DUTY C.I.INSPECTION CHAMBER COVER AND FRAME weight as per I.S.I. specification painted WITH 3 COATS OF black bitumastic superior paint complete as per standard design. (a) Size 450 mm X450 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with C.C. topping) (b) Size 450 mm X 600 mm inside (with 455 mm x 610 mm cover and frame single seal pattern I weighing 38 kg with C.C. topping) (c) Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with R.C.C. slab) Note: - Normally inspection chambers of 450 mm x 450mm and 450mm x 600 mm should be constructed. In very exceptional cases where connections cannot be accommodated in 450 mm X 600 mm size inspection chamber of 600 mm x 900 mm be adopted. (HSR 29.84)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE EUROPEAN TYPE WATER CLOSET SUITE WITH CONCEALED ‘P’ or ’S’ TRAP with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item no.30.3 above. (i) White (HSR 30.6)

EXTRA OVER item nos.30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid. (i) White plastic seat (Solid) (HSR 30.13) (i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineerin- charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC.(vi) Size 630 mm x 450 mm with one no. tap (HSR 30.41) (v) Size 560mm x 450 mm with one no. tap.

PROVIDING A N D F I X I NG I N POSITION BEST INDIAN MAKE PAPER HOLDERS F I X ED INTO Wall With C.P. brass screws complete in all respects INCLUDING CUTTING AND MAKING GOOD T H E WALLS ETC. (a) C.P. BRASS. (HSR 30.67 a)

PROVIDING A N D FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawls lugs embedded in walls with CP. brass screws, complete in all respect INCLUDING CUTTING AND MAKING GOODS T H E WALLS ETC. (a) 25 MM DIA, C.P. BRASS ADJUSTABLE. 750mm long (HSR 30.68 (a) 25 mm DIA C.P. Brass Adjustable 750 mm long.

PROVIDING A N D FIXING IN POSITION GLASS SHELF FIXED IN WITH RAWL PLUGS WITH C.P. BRASS SCREWS, COMPLETE INCLUDING CUTTING A N D MAKING GOOD T H E WALLS ETC. (a) WITH C.P. BRASS BRACKETS A N D GUARD RAIL (i) 600 mm x 125 mm (HSR 30.69 a (i)

Providing and fixing in position best Indian make soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc. (a) CP. BRASS (i) Soap dish large (HSR 30.70 (a) (i)

PROVIDING A N D FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 M M T H I C K MIRROR mounted On ASBESTOS Sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHROMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD T H E WALLS ETC. a) INDIAN MAKE (i) 600 mm x 450 mm (HSR 30.71)

Providing and fixing in position 15 mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). (a) Bib cock long body (HSR 30.75 a)

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge). (a) 15 MM STOP COCK (ii) Concealed stop cock with flange (HSR 30.76)

Providing and fixing C.P. brass liquid soap container of best quality (as required by the Engineer-in-charge (HSR 30.77)

PROVIDING A N D FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE T U B E CONNECTION (b) C.P. Brass (iii) 15 mm x 450 mm (HSR 30.82 b(iii)

PROVIDING A N D F I X I NG IN POSITION M.S. OR HEAVY FLAT IRON CLAMPS made out of M.S. flat not less than 5 mm of the approved design for fixing c.i. SOIL WASTE V E N T OR A N D PIPES TO WALLS COMPLETE IN ALL RESPECTS INCLUDING CUTTING AND MAKING GOOD THE WALLS A N D FLOORS ETC. AN D PAINTING (HSR 30.88) (a) for 100 mm internal Diameter pipes

PROVIDING AN D F I X I NG I N POSITION AUTOMATIC BRASS BALL VALVES IN TANKS. (HSR 30.110) (b) WITH PLASTIC BALL (i) 15 mm internal diameter

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O. K. Supreme make with covers/lids marked with IS 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge. (Except civil work) (HSR 30.119) 1000 Ltrs. Capacity water Tank

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge (DSR 18.17) 15 mm nominal outer dia Pipes (DSR 18.17.1)

20 mm nominal outer dia Pipes (DSR 18.17.2)

25 mm nominal outer dia Pipes (DSR 18.17.3)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (DSR 17.16A)

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White (DSR 17.18.1)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia (DSR 17.28.1.2) Note:- In case of any difference in the unit & nomenclature of any of the HSR items of Civil, P.H., E.I work depicted in the DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable.