Provn of highly durable K9 ductile iron pipe line from sump to view point with distribution line from view point to academic block at RMS Dholpur

Amount

Supply and fixing of GI water tubing IS-1239 marked, medium grade, in including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the following sizes :- Note :-excavation earth work will be measured and paid saperatly.

20mm bore

25mm bore

50mm bore

80mm bore

Supply ,laying jointing,commissioning and testing Ductile iron pipe with spigot and socket end centrifugally cast(spun), including rubber gaskit, class K-9 conforming to IS-8329-2000 in any length laid in trenches complete all as specified and directed of size 100 mm bore

Material and Labour for DI fitting suitable for size of 100mm dia DI pipe line complete all as specified.

Material and labour for fixing Sluice valve flanged of class PN 1.6 ISI marked 14846-2000 complete with stainless steel spindlle ,flanged both ends, drilled CI gate with brass ring and iron hand wheel and suitable for 80mm bore sizes GI/CI/DI pipe line complete all as specified.

Material and labour for fixing Sluice valve flanged of class PN 1.6 ISI marked 14846-2000 complete with stainless steel spindlle ,flanged both ends, drilled CI gate with brass ring and iron hand wheel and suitable for 100mm bore sizes GI/CI/DI pipe line complete all as specified.

Supply and fixing of non return valve cast iron Disc PN 1.6 flanged ends ISI marked of 100 mm bore complete all as specified.

Supply and fixing of cast iron Air Relese Valve flanged type PN 1.0 suitable of size 100mm rising main with complete parts double ball/orifice flanged type complete all as specified.

Material and labour for fixing Gun metal, globe or gate valve with iron wheel head, Screwed both end for iron pipe conform to IS 778-1984 complete all as specified and of the following sizes :-

50 mm bore

25mm bore

20mm bore

Supply, install testing and comissioning open well submersible pumpset of capacity 20HP electric driven 415V three phase 2700-2900RPM having water discharge capacity of more than 200LPM made of stainless steel body including mounting accessories ,GI clamp ,channels ,rubber gasket hanging rope made up of SWR or nylon water proof rope of sutiable dia etc and fabrication if any, Head range of the pumpset should be minimum 125m complete all as specified. NOTE- (i) Contractor shall test run the pump set by deputing sutiable tecnician from OEM in front of engineer-in-charge till achiving satisfactory result (ii) Submersible cable of 25sqmm dia 3core PVC cable upto length of 30m is inclusive in the rate quoted by the contractor.

S&F fully automatic star delta starter for submersible pump, in sheet steel enclosure, suitable for 40 HP, AC Supply, 50 Hz, 415 Volt, 3 Phase, ML type with suitable relay range and contactors, complete with all connections including testing complete all as specified.

Construction of valve pit of the size 120x120x120 cm of double brick masonary with internal plastering from the top of surface including cover of MS sheet 3.15mm thick and angle iron 40mmx40mmx6mm with hinges and locking arrangement including painting with two coat of synthetic enamelled paint over a coat of red oxide and grouting to PCC 1:2:4 plastering in cement morter 1:3, foundation concrete 1:3:6 including necessary earthwork complete all as specified.

M&L for PVC circular tank cylindrical anti bactirial and placed vertical of RO plant raw water and filtered water storage of capacity 2000 ltrs white colour including making hole for pipe connection with washers and nipple of suitable size complete all as specified.

M&L for PVC circular tank cylindrical anti bactirial and placed vertical of capacity 5000 Ltrs white colour including making hole for pipe connection with washers and nipple of suitable size complete all as specified and directed by Engineer in Charge

Supply, install testing and comissioning open well submersible pump single phase 50Hz IP 68 protection of capacity 2 HP having advance water cool motor design ,dynamically balanced rotating parts compact design inclusive of starter panel complete all as specified.

Excavation in trenches not exc 1.5m in depth and not exc 1.5m wide for taking out/laying pipeline and cable and getting out in soft/disintegrated rock soil complete all as specified.

Returning filling in including spreading, levelling watering and well ramming in layers not exc 25cm complete all as specified.

Removing Excavated hard rock soil at a distance not exc 50m and deposited where directed complete all as specified

M&L for PCC work for pedestal pillars, foundations, coping and other misc support to external water supply installation type c1 mixing ratio 1:3:6 using 20mm graded aggregate complete including form work etc complete all as specified.

Supply install testing and comissioning of Pipeless Filtration plant of high class acrylic material of capacity minimum 25000 LPH including pipeless filter pump of 2HP , filtration basket, chlorine feeder, handrail 2 pc of SS, swim jet and time controller 1 pc all as specified and directed by Enginner in Charge ( 2 working 1 standby)

Supply and install swimming pool ladders grade SS304 or higher with 4 steps complete all as specified.

Supply and testing of maintenance kit having one pc Leaf Net, Standard wall brush 18", algae brush SS 10", telescopic handle 4.8 mtr, hose pipe 15 mtr with standard cuff, test kit and aluinium vaccum head, Make. Lyxar/ION Exchange/Hydropure/Mackway/Arrdev pools

Supply and fix Reverse Osmosis (RO) plant of output capacity of 500 liters per hour complete with errection and comissioning and testing consisting of FRP pressure vessel, multi port valve, initail charge of media i.e. Peebles, PVC pipe work,activated cabon filter, special antiscalant Dosing system system incorporting dosing pump, dosing solution tank , micron cartidge filtration filter , filter housing, pressure pump with motor, RO membrane and tube, TDS meter, flow indicator, skid mounted control panel, pressure switch and gauge, electonic panel consisting of over load protection, fault indicator, amp meter voltmete, hourmeter all as specified. Make Aquafresh India,/Aqualite plus/ ION Exchange

Supply and spread unwashed dry river sand for cushioning for covering the under ground cable in trenches complete all as specified.

Factory made unreinforced precast concrete cable covers conforming to IS:5820, class LV type 1 size 250x150x40 mm for cable protection complete all as specified.

Supply and install feeder pillar box factory made cubical type outdoor with locking arrangements made up of MS sheet of 3mm thickness, CRCA FRP proof,zinc coated 7 tank washed, including spraying light smoke grey weather proof metallic paint with RYB indicators, 100A capacity Aluminium bus bar, 01 TPN MCCB 63A , suitable cable jointing arrangements etc mounting channels made up of MS angle all as specified and as directed

M & L for Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 2.25 Mtr below the ground level with the top edge of earth plate, depth not less than 1.5 Mtr below the ground level connected to copper earth strip of 20 mm x 3 mm size by means of bolts, nuts and washers protected by GI tubing light grade 40 mm dia uptoTest point 20 mm dia watering pipe medium grade with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick PCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in any type of soil ,removal of surplus soil and providing charcol dust & salt layers all around the earth plate upto 15 cm all as required specified & directed by engr in charge.

Supply laying and testing cable XLPE insulated, screened PVC bedded, galvanised steel stripped or wire armoured electric cable heavy duty with stranedd aluminium conductor, 1100V grade of size 25 sqmm 4 core all as specified.

Supply & laying light grade GI Pipe of size 40 mm bore, ISI marked in trench for cable protection complete all as specified and directed.

Supply and fixing mild steel rolled sections such as angles etc. As in main and cross beam, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding dorrs, fixed with angle cleats or other connected plates confirming to grad Fe 290 (Gde E-165) complete all as specified

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering / cladding to wall, molding / folding in circular / semicircular of any position and height fixed with self tapping screws as specified, as directed by Engr-in-charge

S&F Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks, chowkat for door and similar work confirming to Fe-290 Gde-E-165.

S&F welded steel wire fabrics n exc 4Kg fitted to steel members all as specified and directed.

M&L for two coats of synthetic enamel paint on steel surfaces or surface of any description over one coat of red oxide over 10 cm in width or girth not otherwise described including preparation of surfaces.

Chipping and cleaning the surfaces which are to receive the coating or treatment, must be free from oil, laitance, grease, wax, dirt or any other form of foreign material adhering on it before the water proofing job started. Dust free the surface, including removing of existing treatment/ Old felt/ loose plaster/ concrete etc and repair the joints or pointing with polymer mortar by adding bonding agent (SBR) with cement as complete all as specified & directed.

M&L for water proofing treatment on roofs/slabs/ Pool by applying FOSROC high performance & ultra flexible polymer modified elastomeric waterproofing membrane system for concrete and masonary surfaces two component polymer modified waterproof membrane which is supplied in ready mix kits.Brushbond UltraFlex, when fully cured, provides a seamless elastomeric waterproof membrane for use in roof areas, wet areas, bathroom, water tanks, swimming pool, raservoirs,precast joints where a tough elastomeric water tight membrane is required. system shall confirms to the requirement of: Adhesion to substrate (ASTM D4541:2002):>1.0 N/mm2 Tensile Strength N/mm2 (ASTM D412:2013)>1.50 N/mm2 Elongation at break(ASTM D412-2013):>150% water vapour transmission (ISO 7783:2018):20.81 g/m2.hr. 25 kg pack covers approximately 16m2 at about 1.0mm thickness depending on surface conditions and water usage. It is recommended that general resurfacing and areas subjected to light foot traffic should recieve a brushbond Ultraflex in two coats of 500 Um (microns) each to give a 1mm thick coatong. Additional coatings may be required for a water retaining structures like swimming pool, water storage tank covered with plaster/tiles. The whole pool so finished shall be hydrotest for a minimum period of 24 hours for curing and for final test. All above operations to be done in order and as per directions of Engineer in charge. Note: At least 15mm of protective plaster recommended on proposed system as a protection.

M&L for 15mm thick rendering/ screed bedding layer in CM 1:3 on floor and walls of water tank complete all as specified and directed

M & L for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate in foundation filling and mass concrete complete all as specified.

M&L for walling of random rubble, uncoursed well bonded bedded, and solidily hearted, built in cement mortar 1:6.

Extra over stone walling for hammer dressing to face stones and dressing,of face beds and joints, as specified, of random rubble walling uncoursed or brought up to courses with maximum depression on face from straight edge held against the dressed surface n. exc. 40 mm, on lime or sand stones complete all as specified.

M&L for Flush pointing to Random rubble masonry, uncoursed or brought up to courses in cement mortar 1:4 complete all as specified.

Rough excavation not exc 1.5 m deep and getting out in soft or disintegrated rocks complete all as specified.

Removal of excavated rock to a distanceExc.100m but n.exc 150m and deposited where directed n. exc 1.5m above the starting point.

Forming embankment including raising or lowering earth, spreading in layer n exc. 30 cm thick, watering, ramming/rolling and finishing to required size, shape, etc. n exc. 1.5 m high from base complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brick work of walls, finished even and sommoth without using extra cement on edges/ Chajjas/Roof projection and simlar courses etc.

M&L for 2 coats of cement base painting on newly plastered surfaces of wall incl preparation of surfaces all as specified and directed.

Surface dressing n exc 15 cm deep in hard/dense soil complete all as specified.

M & L PCC 1:4:8 type D2 using 40mm graded stone aggregate 75mm thick as in Sub floor, Sub -Base, floors and pavings complete all as specified.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand.

M&L cement concrete type C-1 , 1:3:6 (using 20mm graded stone aggregate) as in copings, packing around interlocking paver blocks complete all as specified and directed.

Machine cut kota stone slab 20-25mm thick in riser of steps,skirting, dado and pillar laid ove cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete incl 10mm thick plaster in CM 1:4 complete all as specified.

M&L 100mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in Hard standing/Ramps finished even and fair (Chequered Finish) without using extra cement complete all as specified and as directed.

Tulsi Enterprises (BID ID -3137348)

M/S MAKHIJA TRADERS (BID ID -3137515)