SPECIAL REPAIR TO BLDG NO P 7/11 WITH ATT TOILET SINGLE PBOR ACCN AT MIL STN JAMMU UNDER GE SATWARI

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exc. 1.5 Sqm including making good of jambs of opening with rendering in cement mortar 1:4, complete all as specified and direcetd.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc. 1.5 Sqm but n exc 4.0 sqm including making good of jambs of opening with rendering in cement mortar 1:4, complete all as specified and direcetd.

S&F pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified.

S&F pressed steel frames of size 105mm x 60mm made out of size 1.25mm thick MS sheet for doors single rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified.

Material and labour for Providing, cement concrete 1:2:4 type B-1 (using 20mm graded aggregate), in lintels upto 1.5m clear span, cills, steps seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed.

Supply and fixing 35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars,stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified.

S&F Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. .

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed by Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge.

S&F 150mm size mild steel handle complete all as specified and as directed.

S&F butt hinges of mild steel cold rolled medium weight of size 100mm as specified.

S&F Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

S&F Aluminium handles, fabricated type, anodised Size-100mm, anodised section and fixed complete all as specified. (ISI Marked)

S&F Aluminium alloy, anodised, sliding door bolt Size- 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F aluminium hanging floor door stopper,Twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc complete all as specified.

S&F aluminium bottom door seal with brushes, length not less than1.2 mtr, fix with screw, suitable for wooden door complete all as specified.

Supply and fixing in repair mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

Material & labour factory made steel windows double shutter box type, outer frame made out of ERW TUBE 'P' section(60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required. Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) for Provn of one shop coat of zinc chromate primer on all exposed steel surfaces and one coat of coal tar on the ends of steel frame in contact with brick/conc surface (ii) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (iii) PCC block for embedding lugs. (Gill shall be measured separately)

Ditto as per above item no- 19 but in ventilators any size

S&F Mild steel works of flat iron, square bar, round bars etc. as in framed work such as grills, guard bars, gratings etc incl bending, cutting and welding as necessary of confirming to Gde Fe 310-0 all as specified.

S&F 4 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

Supply and fixing Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified fixed with stainless steel wire staples.

S&F in repair CP Bib taps(15mm dia), fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified complete all as specified.

S&F in repair angle valve with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified.

S&F in repair Stop valves (20mm dia), cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified.

S&F in repair CP Pillar taps(15mm dia), cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

S&F in repair PVC connection 15 mm x 600 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.

S&F in repair Brass chromium plated shower rose with or without swivel joints, 125mm size, including fixing to steel pipe or union etc

S&F in repair Jet Spray (Stainless Steel) with 1.5 meter Tube complete all as specified.

S&F in repair under counter basin with fixing accessories set, size: 560 x 470mm, Oval shape, including CP cuppling and PVC waste pipe complete all as specified.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom,complete all as directed. (Rate of including in taking out and removal of old WC seat unhygienic condition.

S&F in repair Urinal with complete accessories Set, CP waste cuppling, waste pipe, sprader etc. Size: 375 x 390 x 590mm complete all as specified.

S&F in repair urinal sprader cpmplete all as specified complete.

S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including L bend, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition).

S&F in repair stainless steel lock grating plain/hole size 100 mm dia including embeding in tiles with white cement.

Supply and fixing in repair PVC Waste pipe 32mm bore of required length complete all as specified.

M&L for dismantling of water tank of capacity exc 1000 to 2000 ltrs and removing complete all as specified and as directed.

Supply and fixing Rotational moulded polyethylene water storage tanks of 1000 litres capacity, (cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified

M&L for mild steel rolled work as in tank staging (framed) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing( Beam, tee, angle, channel or flat sections) including distance pieces, cleats, gusset plates, etc, conforming to grade Fe 290 complete all as specified.

Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified.

Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

Supply and fixing tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

M&L cutting chases, pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc,and cutting chases for concealed water tubing or concealed conduit wiring,etc, and making good, cutting n.exc 10cm girth in brick walls.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend, branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC (SWR) , bends for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC (SWR) , bends with access door for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR) , bends for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC branch piece, single (single 'Y') with access door for 75 mm bore complete all as specified and directed.

Supply and fixing, UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore , complete all as specified and as directed by Engineer-in-charge.

S&F UPVC (SWR) , reducers 110 mm dia complete all as specified.

S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified.

Supply and fixing in repair UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair, UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material from the work site ouside defence premises complete all as specified.

M&L brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge

M&L brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified and as directed by Engineer-in-charge

Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises. complete all as specied and directed.

Material and labour glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified.

Material and labour Non-skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4 complete all as specied and directed.

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 as directed by Engr-in-charge.

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

M&L for 50mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

M&L for Plain cement concrete (1:3:6), type C-2 (using 40 mm graded crushed stone aggregate) nominal mix, 75 mm thick, as in sub base of floors, finished even and fair complete all as specified and as directed by Engineer-in-charge.

M&L for 25 mm thick cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed.

Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L Rendering 15mm thck in CM 1:4 on Concrete surfaces of roof finished fair & evenr and including mixing of water proofing compound (WPC shall be measured and paid separately)

M&L for water proofing treatment in the following sequences:- (a) Applying 1st course of bituminous primer conforming to IS -3384 @ 0.4 Kg/Sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely. (b) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed .

M&L for preparation of newly sufrace of APP Membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm, complete all as specified and as directed

Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by Engineer-in-charge.

Supply only Water proofing compound liquid.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified. Note :- Work will be carried out upto 4th storey of bldgs also as per direction of Engr-in-charge including necessary formwok and scaffolding required as per site conditions & no extra payment shall be made on this account.

M&L for rendering 10mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:6 , rendering is to be finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L for rendering 15 mm thick on other than fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement (up to 4th storey with necessary scaffolding) complete all as specified and as directed by Engineer-in-charge.

M&L for rendering 10 mm thick on fair faces of brick or concrete surface ceilings, in cement mortar 1:3, rendering is to be finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth complete all as specified.

M&L for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width/girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth complete all as specified.

M&L for preparation of old decorated concrete/ plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying one coat of oil bound distemper on old decorated wall surface including two coats of wall care putty of 3 mm thick on uneven surface as and where required.

Material and labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified.

M&L for preparation of New/old decorative plastered/concrete surface of wall, chajja, facia, face of columns, beam ect by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying one coat of weather proof exterior emulsion (APEX) with necessary scaffoding up to 4th storey, including necessary filling of wall care putty on uneven surface as and where required all as specified.

M&L for preparation of new plastered/concrete surfaces of walls and applying two coat of cement based paint over one coat of primer complete all as per specified and directed by Engr-in-charge.

M&L for preparation of old decorated plastered /concrete/ brick surfaces of walls and applying one coat of cement based paint on old decorated surfaces including preparation.

M&L for preparation of old decorated brick /concrete plastered /un-plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of lime white wash on the walls, pillars, cornices etc. complete all as specified and directed.

M&L for preparation of new decorated brick /concrete plastered /un-plastered surfaces of Ceiling and applying three coat of white wash on ceiling.

Demolition of reinforced cement concrete of any discription and any position and removing the rubbish from the work site out side defence premises complete all as specified.

M&L for RCC M-15, nominal mix, type B-1 (1:2:4), using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and directed.

M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed

Demolition of cement concrete (unreinforced) ground floor and pavings n exc 15 cm thickness (below or above ground level ) and removing the rubbish from the work site out side defence premises complete all as specified.

M&L Cement concrete type 100 mm thick, D- 2, 1:4:8 (40mm graded aggregate) complete all as specified.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nanital or similar pattern roof covering.

M&L Pre- painted galvatume aluminum zinc coating (AZ-150 Micron) GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Dismantling structural steel work including doors, gates, beams but excluding framed truss etc

M & L Rolled/square/round pipe sections as in main and cross beams, hip and jack rafters; purlins where connected common rafters and running rails and guides for sliding doors;fixed with angle cleats or otherconnecting plates Fe 410-W(grade-E-250) quality-A complete all as specified.

Dismantling of ceilling board(fiber, pulp,any type of insulation etc) or insulation board/ slabs/any thickness including cover fillets.

Supply and fixing in repair GI snap grid frame work (grid size 605cm x 605cm) for false ceilling consisting of main runner 'T' of size 24mmx32mm and 0.3mm thick, secondary runner 'T' of size 24mmx25mm and 0.3mm thick, GI angle 24mmx24mm and 0.4mm thick, bottom exposed capping of width 24mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm/sqm, ceilling grid system duly suspended by 4mm dia GI wire hanging from existing purlinn/roof slab with butterfly clips including gypsum ceilling tiles of size 595x595x9mm laminated with 0.07mm thick polyvinyl film on the face side and 10micron metalised polyester film on the back side fixed on GI snap grid complete all as specified and directed by Engineer-in-charge.

Taking down carefully aluminium conductor point wiring (light, fan, socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down of unsv MCB DB SPN /TPN along with MCB's

Taking down of unsv Sub main wiring of any size

M & L for complete point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed for the following :- (a) One Light / Fan/ Exhaust Fan point controlled by one, one way switch 6 Amp complete

(b) One 3 pin socket outlet 6 amp independent

(c) One 3 pin socket outlet 6 amp same board

All as per srl item No 115 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Supply and fix modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

Supply and fix modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

Supply and fix modular type fan regulator step down 120 Watt, 2 module complete all as specified and directed.

Supply and fix ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fix LED light fitting 1 x 18Watt, 220V, AC decorative box type with driver, holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all fixing arrengenment all as directed by Engr in chage. Note:- The LED batten and LED tube rod shall be of same make.

Supply and fix of lamp holder,PVC /Polycarbonate type with back plate for batten fitting .

Supply and fix LED lamp suitable for B22 holder of capacity 10 Watt.

Supply and fix energy saving new generation 10W LED IP65 bulk head luminaire with opal diffuser complete all as specified and directed.

Supply and fix Distribution Board (SPN) double door 8 Way and should be IP 43 protected with Copper Bus bar 100 Amp rated ,Earth Bar ,neutral Bar Door Earthing.

Supply and fix MCB SPN complete 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

Supply and fix MCB Single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed

Supply and fix sub main wiring with single core cable 2x 6 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 6 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fix of exhaust fan, steel body AC single phase. 230 V of size 300 mm sweep with, blades, and frame and louvers and including making of holes in wall, floor etc all as directed by Engr in charge.

Taking down and refixing of Ceiling fan any size/sweep, including oiling, Greasing and cleaning and applying two coats of synthetic enameled paint after preparation of surface complete over a coat of primer, all as specified and directed by Engr-in-charge.

Supply and fixing ceiling fan complete with blade, down rods, and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with connected from ceiling rose / connector with & including suitable size flexible copper conductor PVC insulated sheathed cord, or including Fan Hook, Clamps, nuts, bolts and down rod suitable length 1.2 Mtr etc complete.

Supply and fix Vertical Distribution Board (VTP&N) 4 way double door suitable for and including MCCB four pole as incomer and out going MCBs and should be IP 43 protected with Copper BusBars, Neutral Links, Earthing bar all as specified and directed. Note:- (i) MCCBs FP & SP shall be measured paid separately (ii) MCB & DB shall have the same make.

Supply and fix 4 Pole MCCB 100 Amp, 415 Volts with rupturing capacity 16 KA , complete all as specified and directed

M & L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

Supply, laying for replacement of unserviciable underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium Multistranded stranded conductor, Armoured cable 50 sq mm 3.5 core cable confirming to IS-7098 Part-I (1988) with latest ammendments.

Excavation in trenches not exceeding 1.5m in width and not exceeding 1.5m in depth and getting out in Soft and loose soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm

Removal of excavated surplus material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specifieds and directed.

Supply & laying dry river sand as cable cushioning 15cm thick layer before laying and 8cm thick over cable after laying the cable in trench complete all as specifieds and directed.

Supply & laying dry bricks over cable as mechanical protection layed flat with width equal to length of brick with sub class 'B' bricks complete all as specifieds and directed.

Material and labour for GI pipe ''light grade'' for road crossing / on wall / on pole with fixed clamps, nuts, bolts for cable protection of size 40 mm dia complete all as specifieds and directed.

M/S SHUBAM ENGINEERS

STAR CONSTRUCTIONS

M/S PAWAN KUMAR ANAND

THAKUR BUILDERS AND CO

M/S RAKESH CONSTRUCTION

AKSHAY CONSTRUCTION COMPANY

CELMAC REGD

NARESH KUMAR AND COMPANY

M/S PARAMJEET SINGH