Construction of tech infra and allied services at Bikaner and MFFR under GE P Bikaner Phase II of II phases on EPC mode

Amount

Engineering, procurement and construction of infrastructure work as listed in Schedule 'A' section-I(Srl item No. 1, 2, 11, 12, 15 & 16) complete as detailed in scope of work including internal water supply & internal electrification work, DBR and other documents of the tender complete as specified and directed.

Engineering, procurement and construction of infrastructure work as listed in Schedule 'A' section-I(srl item No. 3 to 10 , 13, 14 & 17 to 74) complete as detailed in scope of work including internal water supply & internal electrification work, DBR and other documents of the tender complete as specified and directed.

Construction of 04 Nos RCC Blast pen with Traverse wall (Blast pen size 40X25m Ht=8 m) as listed in Schedule 'A' section-I(srl item No.75) with permanent specification, frame structure, ATT, RCC roof, PQC floor etc complete as specified and directed.

Demolition of Buildings (B/R & E/M Portion) Schedule ‘A’ Section -II (Part-I)

Lump sum price worked out by the tenderer for “SITE CLEARANCE AND DEVELOPMENT WORKS" as listed in Schedule ‘A’ Section III Part - I

Lump sum price worked out by the tenderer for “EARTH WORKS" as listed in Schedule ‘A’ Section III Part -II

Lump sum price worked out by the tenderer for “LIGHTENING PROTECTION WORKS" as listed in Schedule ‘A’ Section IV (Part- I)

Schedule ‘A’ Section IV Part- I (LIGHTENING PROTECTION)

Supply and fixing alumimium gutka 40mm dia having internal threaded 12 mm dia and external of 40mm dia and fixed on GI socked complete all as specified and directed .

Supply, installation, testing and commissioning of maintenance free earth grid (Grounding) of interconnected two earth electrode of size 85 mm dia x 3 mtr long each metal conductor of electrode shall be Cu bounded MS strip of 50x6 mm Cu bounding of MS rod/ strip should be Min 250 microns. Earth electrode of 85 mm, depth 3 mtr shall be placed augured bore hole and embadding of interconnected strip shall be cast in high purity electrically conductive granuler material having ultra low resistive value 0.001Ohm-m resulting in increase of the effective surface area of the earth grid to lower the earth resistance conductive earth enhancing material shall be mix with cement in the ratio 3:1 which should not leach chemicals into the asjacent soil or underground water channels and should be in pH neutral range. Earth enhancing material should permanently proted the encased metal components of the earthing system. All hardware like nuts, bolts and washers should be of stainless steel Electrode should withstand fault current upto 35 KA for 1 second, electrodes top terminal be sealed permanently packed with conductive concrete and test link of Cu bonded MS/Copper strip of size 50x6x200 mm shall be taken out to connect the equipment. Test certificate of NABL laboratory shall be submitted by the contractor, RCC pit cover including brazzing of all the joints upto the test point complete all as specified and directed. No pre cast electrodes to be used. Make:- Elancrete/ Vasconite/ Equivalent. Note:-1) Test certificate of earthing material from materail from certified NABL laboratory shall be submitted & verified by GE. 2) Test reports should not be more than 5 years old. 3) Test report for fault currect ohms, compliance, resistivity value from NABL certified/CPRI lab is must & it has to be verified by GE.

Subtotal

Lump sum price worked out by the tenderer for “AIR CONDITIONING AND REFRIGERATOR WORKS" as listed in Schedule ‘A’ Section IV Part- II

Schedule ‘A’ Section IV Part- II (AIR CONDITIONING AND REFRIGERATOR WORKS)

Supply and fix Voltage Stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130V to 300V with output voltage stabilized at 230V with accuracy of +/- 2.5% and of capacity 5KVA

Supply and fix Voltage Stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130V to 300V with output voltage stabilized at 230V with accuracy of +/- 2.5% and of capacity 2KVA

Supply and fixing Refrigarator single door electrial driven (single Phase) capacity 165 Ltrs BEE 5 Star rated, compressor inverter type automatic silver colour,

Supply and fix Voltage Stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170V to 250V with output voltage stabilized at 230V with accuracy of +/- 2.5% and of capacity 5KVA

Supply and fix Voltage Stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170V to 250V with output voltage stabilized at 230V with accuracy of +/- 2.5% and of capacity 4KVA

Subtotal

Lump sum price worked out by the tenderer for “FIRE FIGHTING, FIRE ALARM AND SMOKE DETECTOR SYSTEM" as listed in Schedule ‘A’ Section -V (Part-I)

Schedule ‘A’ Section -V (Part-I) (FIRE FIGHTING, FIRE ALARM AND SMOKE DETECTOR SYSTEM)

Supply and install Auto dialing system (E-dialer) suitable for addressable type fire panel system consisting of stronge capacity of 15 to 20 telephone numbers programmable type ,including connection to the existing fire alarm panel and connecting to the fire station with demonstration complete.Make-Argus,Schrack,esserby honey Well.

Supply and fix SITC of standered detector base for mounting the complete addressable deterctors complete all as specified and directed Make:-Argus, Schrack,esser by Honey well.

Supply and fixing new electric sounder cum strobe suitable for addressable type alarm system complete.

Supply and fixing respones indicator on wall or with the false ceiling with LED indicator lamp suitable for assressable type complete.

Supply and fix manual call point suitable for analgue addressable type fire alarm system complete.

Supply and fix lead acid battery 12Volts,7AH suitable for addressable fire alarm system complete.

Supply and fix laying 2 core 1.5 Sqmm PVC sheathed armourd copper conductor cable 1100Volts grade FRLS cable complete.

Supply and fix an integrated a public address and talk back facility alongwith 06Nos loud speakers with minimum 1KW and necessary connected accessories complete.

Supply and fix, fire exit rout indicator board with inbuilt led luminaire complete set.

Supply and fix repeater panel suitable for two loop addressable type panel complete.

blank

M&L for laying 6 core 1.5 Sqmm armoured, multistranded copper cable.

blank

Subtotal

Lump sum price worked out by the tenderer for “SUMMER APPLIANCES WORKS" as listed in Schedule ‘A’ Section -VI (Part-I)

Schedule ‘A’ Section -VI (Part-I) (SUMMER APPLIANCES WORKS)

Supply and fix Voltage Stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130V to 300V with output voltage stabilized at 230V with accuracy of +/- 2.5% and of capacity 2KVA

Supply and fix refrigerator, electric driven (single phase), capacity upto to 194 Litres .BEE 5 star rated, with specification of turbo cooling technology ensuring faster cooling direct cool single door refrigerator with advanced invertor Technology (RD EMARVEL 215E THIU FS ST, Sossil steel) complete all as specified and directed.

Supply and fix Double door type refrigerator, electric driven (single phase), Total capacity upto to 301 Litres. Refrigerator Capacity 229 mLtrs, freezer Capacity 72 litrs, BEE 3 star rated, with automatic defrost system, with door alarm, twin cooling plus stablizer free operation, movable ie maker, LED Lighting Deodorizing Filter, convertible complete all as specified and directed.

Supply & installation of water cooler fully stainless steel electric driven (Single) phase having approx storage capacity of 40 ltr and nominal cooling capacity of 40 ltrs per hour all as specified and directed.

Supply & installation of water cooler fully stainless steel electric driven (Single) phase having approx storage capacity of 80 ltr and nominal cooling capacity of 40 ltrs per hour all as specified and directed.

Supply & installation of water cooler fully stainless steel electric driven (Single) phase having approx storage capacity of 120 ltr and nominal cooling capacity of 60 ltrs per hour all as specified and directed.

Supply and fixing Deep freezer hard top 320 ltrs capacity having single door all as specified and directed.

Supply & install industries cooler duct type with following specification :- Airflow (M3/H) – 30000 CMH, Discharge – Top/Bottom, Cooling Area – 3000 Sq ft, Air Pressure – 330 P.A., Motor (V/Hz) – 380 to 415v/50Hz/60Hz, Power (Kw) – 3, Phase- Three, Speed – Single, Fan type – Axial (6 Blade), RPM – 1440, Pad Size – 975 x 885 x100 MM, Water Tank – 45 Ltr, Water Drain – Manual/ Auto, Noise (DB) - <79, Net Weight (kg) – Top – 140/ Bottom – 135, Dust filter- Yes, Air Outlet Size – 765 x 765 MM, Dimension LxWxH (MM) – 1343 x 1343 x 1385, Qty Full (40 Hq) – 9, Qty/SKD (40Hq) – 45 Down/39 Top

Supply and fixing of Galvanised Iron Ducting in 22 guage Galvanised iron steel with thicknes of 0.80 mm dia duct with GI nut bolt complete

Supply and fixing of Galvanised Iron Ducting in 24 guage Galvanised iron steel with thicknes of 0.60 mm dia duct with GI nut bolt complete

Supply and fixing of insulation cross link nitrile rubber 9 mm thick with aluminium tapping complete

Supply and fixing of canvas of vibration between duct and plant

Supply and fixing of cooler stand as per site requirement

Supply & installation of Voltage stabilizer for automatic operation single phase naturally air cooled indoor type & designed for input variation between 170V to 250V with output voltage stabilized at 230V with accuracy of 2.5% and of capacity 1 KVA all as specified and directed.

Supply & installation of Voltage stabilizer for automatic operation single phase naturally air cooled indoor type & designed for input variation between 170V to 250V with output voltage stabilized at 230V with accuracy of 2.5% and of capacity 2 KVA all as specified and directed.

Subtotal

Lump sum price worked out by the tenderer for “ROAD , PATH & CULVERTS WORKS" as listed in Schedule ‘A’ Section -VII (Part-I)

Lump sum price worked out by the tenderer for “EXTERNAL WATER SUPPLY WORKS" as listed in Schedule ‘A’ Section -VIII (Part-I)

Schedule ‘A’ Section -VIII (Part-I) (EXTERNAL WATER SUPPLY WORKS)

Material and labour for construction of new valve chamber size 750mm x 750mm x 750mm including necessary earth work in any type of soil, PCC foundation (1:3:6 ) type C-2 , 40mm graded stone aggregate as in base concrete, brick work in CM 1:6 with 10 mm thick plaster internally and 15 mm thick externally in CM 1:4, 4 mm thick MS cover with hinges and locking arrangement fixed to angle iron frame made out of 40x40x6 mm MS angles complete with 2 coat of synthetic enamel paint over one coat of red oxide primer on all metal works and three coats of white wash on all plastered surface of valve chambers complete all as specified and as directed by Engr in charge.

S&L DI pipes K-7,150 mm dia with all fittings like tee, bend elbow etc , confirming to IS suitable for DI pipe in any length laid in trenches complete all as directed. Note :- (a) Earth work and DI special/fittings shall be measured and paid separatly. (b) Cost of joints including jointing materials shall deemed to be included in unit rate quoted by contractor.

S&L DI pipes K-7,100 mm dia with all fittings like tee, bend elbow etc , confirming to IS suitable for DI pipe in any length laid in trenches complete all as directed. Note :- (a) Earth work and DI special/fittings shall be measured and paid separatly. (b) Cost of joints including jointing materials shall deemed to be included in unit rate quoted by contractor.

Cutting the existing DI/GI pipe line of size 250/200/150/100/80 mm bore and inserting suitable size tee / reducer / bend and new connection of GI 50/40/25mm bore pipe complete all as directed.

8. Supply and fixing cast Iron sluice valve PN 1.0 (long body) ISI marked confirming to IS: 14846-2000 suitable for 80mm bore pipe,flanged ends,drilled,stainless steel spindle,CI gate with brass ring,iron wheel handle,complete including jointing material such as nuts,bolts,washers and rubber sheet etc complete all as specified and as directed.

9. Making hole using treanch less technology under road or hard standing suitable for laying and inserting any pipe/Cables upto 200 mm bore, any length by mechanical drill system in the drilled holes,returning ,filling in the end working space including removal of surplus soil and making good the surface all as specified and directed.

Subtotal

Lump sum price worked out by the tenderer for “EXTERNAL ELECTRIC SUPPLY WORKS" as listed in Schedule ‘A’ Section -IX (Part-I)

Schedule ‘A’ Section -IX (Part-I) (EXTERNAL ELECTRIC SUPPLY WORKS)

Supply install and commissioning of Compact Sub Station 1000 KVA, HT Section::- 11 kV, 630 Amp, Indoor Type, VCB Horizontal Drawout Horizontal isolation floor mounting motorized panel with 230v motor mechanism & 24v DC Shunt/Close coil with CT, PT, IDMT Relay, 8 Window Annunciator Model No. SI-801, Battery Power Pack with 7AH Battery & in built charger for 24V Circuit and other fittings & accessories. -01 No. Potential Transformer – 3 Phase cast resin of ratio 11kV/110V, Class-0.5, 100VA with HT Primary Fuses-03 NosCurrent Transformer –Cast resin Ratio: 60-30/5+5A, Core1:Cl.0.5, 15VA, Core2:Cl.5P10, 15V-01 Nos Protection Numerical 2OC + 1EF Relay 7 & Auxiliary Relay Micro Processed based Non-Directional IDMT -01 No. Indication Lamps VCB off / on / auto trip/ Trip circuit healthy/spring charge indication -01 setMetering Multifunction Meter -01 Set Transformer Section :- 1000 KVA, 11/0.433 KV, 3 Phase, 50HZ, ONAN Cooled Oil immersed Copper Wound Step Down “BIS Marked & BEE Star Labelled” Transformer Complete with first filling of IS:335 ISI Marked Filtered & Dehydrated Transformer Oil, having 7 position Off-Circuit tap changer with tapping range +7.5% in steps of 2.5% each with all standard fittings & accessories including OTI, WTI & Marshalling Box. Transformer as per IS-1180(Part-1)-2014 EEL- 3 with amendment no.- 4 Losses @50% Load - 2460W Losses @100% Load - 6364WLT section: LT Panel comprising of LV Side Incomer–01 no. 1600A 4P 415V 36KA MDO Air Circuit Breaker microprocessor based with O/L,S/C & E/F Protection. - RYB Indication -01 No. Ammeter, 1600 A /5A LTCT CL : 1.0, Volt Meter Enclosure Section :- Space Heater with ON/OFF Switch and Thermostat, Single phase switch with socket, LT Cubical illumination Lamp with Door Limit switch and MCB’s for AC / DC Control -01 Set MS Steel Sheet enclosure suitable for Outdoor Installation with MS base channel Provision for receiving Incoming cables thro Bottom entry and out going -01 Set Provision for receiving Incoming through bus duct by bus bar and Outgoing thro cable box bottom entry Excluding Termination Kit & Glands -01 Set Bus Bar – Aluminum-01 Set Earth Bus – Aluminum -01 Set Paint shade: Siemens Grey ( RAL 7032) -01 Set

(i) The transformer oil shall be PCB (polychlorinated biphenyls) free. Meeting new National Electric Code 2023, it is preferred that the transformer oil shall be mineral oil.

(ii) GAS AND OIL ACTUATED (BUCHHOLTZ) RELAYS - Bucholz relay shall be provided with Mercury Free Float Switches.

(iii)Cable Box - All cable boxes shall be provided with disconnecting chambers for easy removal of transformer during maintenance with-out cable dismantling.Termination req on both side HV & LV in cable box

(v)Core material to be sourced directly from the CRGO/Amorphous producer or from their authorized/licensed importer. Transformer manufacturer shall be able to produce the mill’s test report of the core material used for this contract along with purchase invoice and bill of entry.

(vi)The transformer manufacturer must have an in-house dust-free core cutting and processing unit in the same location as transformer manufacturing. The core shall be slit using automated machine and use of hand shear is not allowed. The Burr level should be less than 10 micron

(vii)The winding shall be insulated with thermally upgraded paper (TUP) of thermal class B and use of normal kraft paper is not allowed to be used. Complete core and winding assembly shall be processed and dried using vapor phased drying (VPD) method only. No other method is acceptable.

(viii)Transformer can monitor these data :- Water in oil, temperature, vibration, acoustic and RF noise.

(ix)All routine and type tests shall be done in NABL accredited lab and Bidder should have in-house NABL accredited testing facility.

(x) Core should be boltless step lap design and Bidder should have hydraulic core lifting facility to avoid any jerk at the time of core building.

(xi))OEM should be BIS & BEE certified for all the rating of the transformer that are to be submitted

(xii) To monitor these data • Load • Water content • Temperatures • Continuous Partial Discharge (PD) • Vibration, in Transformer is required. This Transformer is req for critical load, hence monitoring of PD and water content, vibration etc in Transformer is required to be monitor. The vendor should inform if risk parameters exceedlevel specified by IEEE and CIGRE standards and make recommendations for necessary action.Make: Siemens/Schneider / ALSTOM/ ABB/ BHEL

SITC of 11KV Extensible Outdoor duty (IP 55 enclosure) SF6 gas insulated 3way motor operated Ring Main Unit comprising of 1 nos. 630 Amps Load Break Switch as incomer and 2nos. 630 Amps Vacuum Circuit Breaker as outgoing , cable termination from the front, breaking capacity 21KA/3sec (Internal Arc Classification AFLR 21kA-1sec with Bottom Exhaust both for tank and cable box as per IEC 62271-200), enclosed in robotically welded stainless steel tank having IP67 Degree of Protection, leak rate of SF6 gas less than 0.1% and tested as per IEC 60056/60694/60298. Protection CTs shall be ring core type, complete all as specified and directed. The outer enclosure shall have IP 55 protection, it should be Top Opening Canopy type, Indoor RMU placed inside Outdoor Enclosure should not be acceptable. Both the Load break switch and Breaker should have line side earth switch. Make of RMU : SIEMENS (8DJH- ST)/ SCHNEIDER (FBX) / ABB (SafePlus- XT).

(A) NOTE:- Other details:- System Particulars: (i) Nominal System Voltage : 11kV. (ii) Voltage variation on supply side : ±10 %. (iii) Corresponding Highest System Voltage: 12kV. (iv) Frequency : 50 Hz with ± 3 % tolerance. (v) Transient condition : -20 % or + 10 % combined variation of Voltage and frequency. (vi) Number of Phase : 3 Phases. (vii) Neutral earthing :Solidly earthed. (viii) Fault level (minimum) kA /Sec : 21/3). (ix) Lightning Impulse Withstand Voltage (kVp) : 75 (x) One minute dry/wet power frequency withstand voltage primary (kV rms): 28KV (xi) Rated Dynamic Withstand Current (kAp) : 52.5KA. (xii) Number of Short Circuit Operations at rated short circuit current of 21 kA for Breaker - 50 Nos. (xiii) Earth switch should have 5 closing operation at short circuit current (making operations E2 class) independent of breaker. Earth switch manual closing shall be driven by a fast acting / snap action mechanism,independent of operator and VCB action. (xiv) Side and rear cable entry is not acceptable, all operation, interlock, cable terminations and door shall be front side only.

(B) Applicable Standards for this RMU scope of work - IEC 62271-200. (i) The Ring Main Units shall conform to the latest applicable, IEC 62271-100, IEC 62271-200. (ii) All live parts, bus bars,shall preferably be enclosed in non- magnetic and non-ferrite grade stainless steel tank Grade SS441 of minimum 2 mm thickness. The RMU shall be type tested for internal arc test of 21KA/1 sec AFLR with Bottom Exhaust for Safety of Personnel for both Tank as well as Cable Compartment as per IEC62271-200. The outer enclosure shall have IP 55 protection for complete switchgears, however it should be Top Opening Canopy & Indoor RMU placed inside Outdoor Enclosure should not be cceptable. The protection relay shall be for 3 O/C + 1E/F (IDMT Type) Self powered numerical protection relay with low and high set of over current and earth fault,MODBUS communication along with RS 485 Port / USB Port. (iii) Internal Arc Classification should be with Bottom exhaust only. RMUs should be manufactured, inspected, and invoiced from the OEM factory. (iv) Temperature & climatic sensor in each panel, Wireless & Self powered Temperature sensor should be mounted in Busbar & Breaker chamber and the same data should display on the panel. (C) Air Insulated Bus Connected Unit comprising the following, (1) Air Insulated enclosure with necessary bus connection via bushing. VT’s from the manufacturer and according to IS 3156 shall be accepted. (2) 11KV/rt3/110V/rt3; 50VA class 0.5. Single phase bus PT for metering. (3)11KV/230V AC, 1KVA control transformer – Optional is Aux supply at site is not available. (4)MFM – EM 6400 NG Class 0.5 for each Incomer. (5) Metering CT in respective Function’s Cable Compartment in RMU XX/1A, Class 0.5, 2.5 VA. (D). Accessories :- (1) Antireflex operating handle. (2) Battery 24V DC , 12Ah. (3) Battery charger (I/P-230V AC, O/P - 24V DC). (4) Manometer with remote contact.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound techneque and necessary machine or by using manual mechanical tools with manpower including passing ofGI pipe 80 mm dia complete complete all as specified and as directed by the Engineer-in-Charge. Note; lenth of pipe to be measured and paid seperately under relavant item

Supply, install, test and commissioning of factory made floor mounted LT cubical panel confrming to CPRI specification board indoor type (double door) made out of 2mm thick CRCA sheet totally enclosed with necessary ventilations, weather, dust and vermin proof IP-53 minium with front and rear opening and locking arrangement 415Volts, 3 phase, 50 Hz having a aluminum bus bar of capacity 1800Amps and of suitable size to house all LT switch gears and accessories as mentianed below and full neutral duly colour coded and for neutral supported with DMC/SMC insulators colour coded complete connection from bus bar to MCCB with suitable copper cable, panel board shall be grouted in the ground with suitable size of foundation in PCC 1:2:4 type B1, MS channels for base frame as per ground requirement and supports, GI nut, bolts, washers etc. The panel board shall be powder coated and red oxided primed :-

(a) The following items are provided in one compartment :- (i) Digital Voltmeter - 01 No, (ii) Digital Ameter - 01 No (iii) Three Indication LED Lamp

Incomming -

(i) ACB 4 Pole, 415 V, volt adjustable thermal and fixed magnatic type with microprocessor release of capacity ACB 1250 AMP - 01 Nos

Out going :-

(i) MCCB 4P,415 volt adjustable thermal and fixed magnatic type 160AMP, 36 KA -01 No (UG ATC) (ii) MCCB 4P 200 Amp, 36 KA - 01 No (UG OPS ROOM) (iii) MCCB 4P 250 Amp, 36 KA - 01 No (Ex HANGER) (iv) MCCB 4P 520Amp, 50 KA - 01 No (PROP HANGER) (v) MCCB 4P 250 Amp, 36KA-01 (Spare)

Supply, install, test and commissioning of factory made floor mounted LT cubical panel confirming to CPRI specification board out door type (double door) made out of 3.15mm thick CRCA sheet totally enclosed with necessary ventilations, weather, dust and vermin proof IP-53 minimum with front and rear opening and locking arrangement 415Volts, 3 phase, 50 Hz having aluminium bus bar of capacity 250Amps and of suitable size to house all LT switch gears and accessories as mentioned below and full neutral duly colour coded and for neutral supported with DMC/SMC insulators colour coded complete connection from bus bar to MCCB with suitable copper cable, panel board shall be grouted in the ground with suitable size of foundation in PCC 1:2:4 type B1, MS channels for base frame 50x50x6 mm and supports, GI nut, bolts, washers etc. The panel board shall be powder coated and red oxided primed :- (a) The following items are provided in one compartment :-(i) Digital Voltmeter - 01 No, (ii) Digital Ammeter - 01 No (iii) Three Indication LED Lamp. Incoming -(i) MCCB 4P, 415 volt, Adjustable thermal and magnetic type, 160AMP, 35 KA -01 No. Outgoing:- (i) MCCB 4P, 415 volt, Adjustable thermal and fixed magnetic type, 160 AMP ,35KA -01 Nos (ii) MCCB 4P 415 volt, Adjustable thermal and fixed magnetic type, 160 AMP ,63 AMP ,25KA -02 Nos (iii) Changeover Switch - 160 Amp -01 Nos

Supply, install, test and commissioning of factory made floor mounted LT cubical panel confrming to CPRI specification board out type (double door) made out of 3.15mm thick CRCA sheet totally enclosed with necessary ventilations, weather, dust and vermin proof IP-53 minium with front and rear opening and locking arrangement 415Volts, 3 phase, 50 Hz having aluminium bus bar of capacity 1000Amps and of suatable size to house all LT switch gears and accusories as mentianed below and full neutral duly colour coded and for neutral supported with DMC/SMC insulators colour coded complete connection from bus bar to MCCB with suitable copper cable, panel board shall be grouted in the ground with suitable size of foundation in PCC 1:2:4 type B1, MS channels for base frame 50x50x6 mm and supports, GI nut, bolts, washers etc. The panel board shall be powder coated and red oxided primed :-

(a) The following items are provided in one compartment :- (i) Digital Voltmeter - 01 No, (ii) Digital Ameter - 01 No (iii) Three Indication LED Lamp

Incomming -

(i) MCCB 4P, 415 volt adjustable thermal and fixed magnatic type 630AMP, 35 KA -01 No

Out going :-

(i) MCCB 4P, 415 Volt, adjustable thermal and fixed magnetic type , 200 AMP ,35KA -01 Nos (ii) MCCB 4P ,63 AMP ,25KA -01 Nos-SPAIR (iii) Changeover Switch - 200 Amp -01 Nos

Supply, install, test and commissioning of factory made floor mounted LT cubical panel confrming to CPRI specification board out type (double door) made out of 3.15mm thick CRCA sheet totally enclosed with necessary ventilations, weather, dust and vermin proof IP-53 minium with front and rear opening and locking arrangement 415Volts, 3 phase, 50 Hz having aluminium bus bar of capacity 1000Amps and of suatable size to house all LT switch gears and accusories as mentianed below and full neutral duly colour coded and for neutral supported with DMC/SMC insulators colour coded complete connection from bus bar to MCCB with suitable copper cable, panel board shall be grouted in the ground with suitable size of foundation in PCC 1:2:4 type B1, MS channels for base frame 50x50x6 mm and supports, GI nut, bolts, washers etc. The panel board shall be powder coated and red oxided primed :-

(a) The following items are provided in one compartment :- (i) Digital Voltmeter - 01 No, (ii) Digital Ameter - 01 No (iii) Three Indication LED Lamp

Incomming -

(i) MCCB 4P,415 volt adjustable thermal & magnatic type 630 Amp 50KA-01No

Out going :-

(i) MCCB 4P,415 volt adjustable thermal & magnatic type 630 Amp ,50KA -01 Nos (ii) MCCB 4P ,63 AMP ,25KA -01 Nos (iii) Changeover Switch - 520 Amp -01 Nos

Supply, install, test and commissioning of factory made floor mounted LT cubical panel confrming to CPRI specification board out type (double door) made out of 3.15mm thick CRCA sheet totally enclosed with necessary ventilations, weather, dust and vermin proof IP-53 minium with front and rear opening and locking arrangement 415Volts, 3 phase, 50 Hz having aluminium bus bar of capacity 400Amps and of suatable size to house all LT switch gears and accusories as mentianed below and full neutral duly colour coded and for neutral supported with DMC/SMC insulators colour coded complete connection from bus bar to MCCB with suitable copper cable, panel board shall be grouted in the ground with suitable size of foundation in PCC 1:2:4 type B1, MS channels for base frame 50x50x6 mm and supports, GI nut, bolts, washers etc. The panel board shall be powder coated and red oxided primed :-

(a) The following items are provided in one compartment :- (i) Digital Voltmeter - 01 No, (ii) Digital Ameter - 01 No (iii) Three Indication LED Lamp

Incomming -

(i) MCCB 4P,415 volt adjustable thermal & magnatic type 250 Amp 35KA-01No

Out going :-

(i) MCCB 4P,415 volt adjustable thermal & magnatic type,250 AMP ,35KA -01 Nos (ii) MCCB 4P ,63 AMP ,25KA -02Nos (iii) Changeover Switch - 250 Amp -01 Nos

Supply and fixing thermplastic cable junction box with IP 66/67 weather proof protection for outdoor installation with knockouts for cable entry of size 205x255x122mm suitable for LT UG cable 10Sqmm to 25Sqmm make Hensel/Sintex

Supply &Fixing FRLS PVC insulated copper conductor ,two single core of size 2.5Sqmm complete for terminal box to steel/flood light fitting.

Supply and fixing compact air insulated bus bar trunking system with aluminium bus bar 1250Amps 50KA breaking capacity,IP54 protection complete all as specified and directed by Engr-in-charge.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine or by using manual mechnical tools with manpower including passing HDPE 150 dia suitable for 0.4 mpa working pressure or GI pipe light grade 100mm bore dia for proection of LT Cables.

Supply and fix 4 Pole MCCB 12 to 63 Amp, 50 Hz, 415 V with rupturing capacity 25 KA. (For Religious Institute , Unit Shop , MI Room & Addl Specialised Accn and Facilities in LT Panel BOQ Item No : 223 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix RCCB with MCB of 2 pole , 16 Amp rating with sensitivity of 30 mA suitable for 240 Volts. (For MT Area ,Baggage Room , Garrage for Ambulance ,Garrage for Cycle , Store 1 & 2 & Stores (Sqn HQ) in LT Panel BOQ Item No : 223 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 63 to 100 Amp, 50 Hz, 415 V with rupturing capacity 25 KA. (For ADM Block & Officer Mess in LT Panel BOQ Item No : 224 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 12 to 63 Amp, 50 Hz, 415 V with rupturing capacity 25 KA (For Education Building ,Servant Qtrs for Single Offrs D/S,Briefing Room Complex,Servant Qtrs,OR Institute,Family Welfare Centre & URC in LT Panel BOQ Item No : 224 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix RCCB with MCB of 2 pole , 6 Amp rating with sensitivity of 30 mA suitable for 240 Volts (For fro garrage for Adm block, Flt office and car garrage /Parking in LT Panel BOQ Item No : 224 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 63 to 100 Amp, 50 Hz, 415 V with rupturing capacity 25 KA. (For Single Living Accn for Hav and OR's (D/S) & Ironing Room & Mechanical Laundry in LT Panel BOQ Item No : 225 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 12 to 63 Amp, 50 Hz, 415 V with rupturing capacity 25 KA. (For Transit Accn for 20 Ors, Transit Accn for 05 Offrs & Repair Bays B Veh (77 Nos) & LRW in LT Panel BOQ Item No : 225 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix RCCB with MCB of 2 Pole 10 Amp, rating with sensitivity of 30ma suitable for 240 Volts. (For Vehicle Garrage 'B' Vehicle car garage shed , Covering Parking for scooter shed, in LT Panel BoQ item No. 225 of CA, CEBTZ /BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 500 to 630 Amp, 50 Hz, 415 V with rupturing capacity 50 KA. (For Proposed Main LT panel for ALH-WSI UH FLT Hanger No : 02 in LT Panel BOQ Item No : 227 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 160 to 200 Amp, 50 Hz, 415 V with rupturing capacity 36KA. (For Proposed LT Panel for AC load (ALH - WSI UH FLT Hanger No : 02) in LT Panel BOQ Item No : 227 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 125 to 160 Amp, 50 Hz, 415 V with rupturing capacity 36KA. (For Proposed LT panel for Runway Lights & Dispersal in LT Panel BOQ Item No : 227 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 63 to 100 Amp, 50 Hz, 415 V with rupturing capacity 25 KA. (For Technical Accommodation, (Bay Servicing Fecilities) in LT Panel BOQ Item No : 227 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix 4 Pole MCCB 12 to 63 Amp, 50 Hz, 415 V with rupturing capacity 16 KA. (For Air crew and ground operational readiness room, Tarmac duty with toilet, Visitor lounge with attached toilet,& Kichenet, High Mast Light No. 01, 02,03) in LT Panel BOQ Item No : 227 of CA : CEBTZ/BKN-16 of 2022-23 catered in PH-I).

Supply and fix RCCB with MCB of 2 Pole 10 Amp, rating with sensitivity of 30ma suitable for 240 Volts. (For covered accn for Gen shed,for flight Hanger, Parking Accn for flight hanger in LT Panel BoQ item No. 227 of CA, CEBTZ /BKN-16 of 2022-23 catered in PH-I).

Supply, installation, commissioning and testing of factory made cubical type LT panel Board of Suitable size (CPRI approved) out door type dust proof, vermin proof with IP 54 protection made out of CRCA sheet 3.15 mm thick synthetic enamel paint over a coat of red oxide primer, fully compartmentalized inside panel with 2 mm thick CRCA sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including locking arrangements including provision of rubber beading and mild steel cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with aluminum bus bar capacity 1200 Amps 04 Nos Three Phase and neutral (TPN) (in Separate chamber), bus bar fixed on epoxy coated insulator and provision with 1100 volt grade heat shrinkable type sleeves and housed in independent chamber having access both from front and back side, panel shall be mounted on angle iron frame and 04 No legs made from angle of size 40 x40 x5mm, legs shall be 750 mm long, 450 mm grouted in blocks of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) with 300 mm ground clearance, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, danger notice plate for LT with conventional skull and bones duly riveted/pasted to the panel board door, complete including all connections incoming / out going all as directed by Engineer-in-charge and comprising of following accessories :- (Proposed Main LT panel for ALH-WSI UH FLT Hanger No : 02) INCOMING :- (a) Supply and fix 4 Pole MCCB 800 Amp, 50 Hz, 415 V with rupturing capacity, Thermal megnatic relay adjustable type 50 KA. – 01 Nos

Supply, installation, commissioning and testing of factory made cubical type LT panel Board of Suitable size (CPRI approved) out door type dust proof, vermin proof with IP 54 protection made out of CRCA sheet 3.15 mm thick synthetic enamel paint over a coat of red oxide primer, fully compartmentalized inside panel with 2 mm thick CRCA sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including locking arrangements including provision of rubber beading and mild steel cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with aluminum bus bar capacity 600 Amps 04 Nos Three Phase and neutral (TPN) (in Separate chamber), bus bar fixed on epoxy coated insulator and provision with 1100 volt grade heat shrinkable type sleeves and housed in independent chamber having access both from front and back side, panel shall be mounted on angle iron frame and 04 No legs made from angle of size 40 x40 x5mm, legs shall be 750 mm long, 450 mm grouted in blocks of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) with 300 mm ground clearance, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, danger notice plate for LT with conventional skull and bones duly riveted/pasted to the panel board door, complete including all connections incoming / out going all as directed by Engineer-in-charge and comprising of following accessories :- (Indoor ESP Panel for ALH-WSI UH FLT Hanger No : 02)

33. Supply, installation, commissioning and testing of factory made cubical type LT panel Board of Suitable size (CPRI approved) out door type dust proof, vermin proof with IP 54 protection made out of CRCA sheet 3.15 mm thick synthetic enamel paint over a coat of red oxide primer,fully compartmentalized inside panel with 2 mm thick CRCA sheet powder coated, to accommodate the incoming and outgoing each switch gear shall have be independent opening and having provision for front and rear side opening with double door with hinges including locking arrangements including provision of rubber beading and mild steel cable glands for each cable to make it weather and vermin proof, provision of air fins for ventilation, complete with aluminum bus bar capacity 300 Amps 04 Nos Three Phase and neutral (TPN) (in Separate chamber), bus bar fixed on epoxy coated insulator and provision with 1100 volt grade heat shrinkable type sleeves and housed in independent chamber having access both from front and back side, panel shall be mounted on angle iron frame and 04 No legs made from angle of size 40 x40 x5mm, legs shall be 750 mm long, 450 mm grouted in blocks of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) with 300 mm ground clearance, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, danger notice plate for LT with conventional skull and bones duly riveted/pasted to the panel board door, complete including all connections incoming / out going all as directed by Engineer-in-charge and comprising of following accessories :- (Outdoor ESP Panel for ALH-WSI UH FLT Hanger No : 02)

Supply, installing, commissioning and testing LT panel board (out door type) cubical type made out of CRCA sheet 3.15 mm thick dust and vermin proof and angle iron of suitable size , pedestal frame grouted in PCC (1:2:4) type B-1 20mm graded stone aggregated thimble and cable entry boxes with cable glands. Panel should covered from all sides with front and back lockable door and hinges complete with aluminum bush bar of capacity 200 Amps, TPN, three phase, 04 wire (In separate chamber) including painting with two coats synthetic enameled paint over a coat of red oxide primer and consisting of the following :- Proposed LT Panel (For Blast Pens and street lights)

(a) Supply and fix 4 Pole MCCB 125 Amp, 50 Hz, 415 V with rupturing capacity, Thermal megnatic relay adjustable type 36 KA. – 01 Nos (Incoming)

(b) Supply and fix 4 Pole MCCB 100 Amp, 50 Hz, 415 V with rupturing capacity, Thermal megnatic relay adjustable type 25 KA. – 02 Nos (Out going for Explosive Storage hut with travers)

(b) Supply and fix 4 Pole MCCB 16 Amp, 50 Hz, 415 V with rupturing capacity, Thermal megnatic relay adjustable type 25 KA. – 02 Nos (Out going for Blast Pen)

(e) LED Indicated Lamp (R,Y,B) one Set-01

Supply and fix Cable route indicator (duly engraved with LT Cable 1100 Volt on cast iron round plate 150 mm dia with provision of 500mm long (Minimum) single leg /stand of flat iron 50X6mm welded on back side of plate fixed and grouted in position with PCC type C-I block of suitable size complete. complete all as specified and directed by Engr -in-Charge.

Gl. Octagonal pole 7.0 mtr long top dia 70 mm & bottom dia 130 mm with base plate 220 x 220 x l2 mm, thickness 3.0 mm, including G.l. Foundation Nut & Bolt [420, 600 mm long (4 Nos) & GI. Single arm bracket 1.0 mtr long 40 mm dia. Including earth work After erecting Painting of pole upto 1.5 Mtr Height from PCC Coping with two coats of synthetic enamel paint in alternate black and white strip 30cm side each strip 5 Nos including marking pole number in letters and figures of size not les than 10cm height with red colour enamel paint complete.

40. Supply and fix Junction box with aluminium bus bar suitable for 3 phase & neutral 4 wire of capacity 32 Amps and MCB 6 Amp SPN complete with fixing clamps etc.

Supply anf connecting 3 Core cord flexible wire copper conductor multistranded PVC insulated and overall PVC sheathed of size 3X1.5 sqmm 1100 volt, draw through LT steel tubular poles for connection to street light from junction box as directed by Engineer-In-Charge.

S&F Double wall corrigated pipe outer dia 160 mm and inner dia 136 mm dia for 630 Sqmm/400 Sqmm 3.5 core cable protection complete all as specified and directed by Engineer - In - Charge.

S&F Double wall corrigated pipe outer dia 120 mm and inner dia 103 mm dia for 185Sqmm/120 sqmm/95 Sqmm 3.5 core cable protection complete all as specified and directed by Engineer - In - Charge.

S&F Double wall corrigated pipe outer dia 90 mm and inner dia 76 mm dia for 70 Sqmm/ 50 Sqmm 3.5 core cable protection complete all as specified and directed by Engineer - In - Charge.

S&F Double wall corrigated pipe outer dia 63 mm and inner dia 50 mm dia for 35 Sqmm 3.5 core / 25 Sqmm 4 core cable protection complete all as specified and directed by Engineer - In - Charge.

S&F Double wall corrigated pipe outer dia 50 mm and inner dia 38 mm dia for 16 Sqmm 4 core /10 Sqmm 4 core/10 sq mm 2 core cable protection complete all as specified and directed by Engineer - In - Charge.

Subtotal

Lump sum price worked out by the tenderer for “SEWAGE DISPOSAL WORKS" as listed in Schedule ‘A’ Section - X (Part-I)

Schedule ‘A’ Section - X (Part-I) (SEWAGE DISPOSAL WORKS)

Supply and Laying DWCPE (SNB) drain pipies 180mm Outer dia/ 163mm Internal dia as per IS-16098 (Part-II), laid in trenches over 100mm thick bedding comprising of well compacted clean poorly graded gravel, gravel/sand mixture with little or no fines to required slope, including all accessories/ fittings/ jointing ring, jointing and testing complete ll as specified and as directed. Note : - Excavation, earthwork, returning filling and bedding for pipe shall be measured & paid separately under respective item.

Supply and laying DWCPE (SN8) confirming to IS-16098,150mm nominal bore (160mm OD) laid in trenches on and including bed 100 mm thick beding compressing of well compacted clean poorly graded gravel, gravel/sand mixture with little or no fines to requiered slope, including all accessories/fitting/jointing and testing complete all as specified and directed.

Supply and laying DWCPE (SN8) confirming to IS-16098, 200 mm nominal bore (238 mm OD) laid in trenches on and including bed 100 mm thick beding compressing of well compacted clean poorly graded gravel, gravel/sand mixture with little or no fines to requiered slope, including all accessories/fitting/jointing and testing complete all as specified and directed.

Subtotal

Lump sum price worked out by the tenderer for “AREA DRAINAGE WORKS" as listed in Schedule ‘A’ Section -XI (Part-I)

Schedule ‘A’ Section - XI (Part-I) (AREA DRAINAGE WORKS)

Material & Labour for Precast drain of High strength precast reinforced concrete M-50 grade using Fe 500 D grade TMT steel reinforcement bar, drains size 600x600(WXH) U shape, Section of drain shown on drawing , manufactured with high performance self compacting concrete, as per Japanese Industial standers (JIS) confirming to Indian Standards and capable of carrying a wheel load of 2.4 tonnes for light veh movement. Useful for appications such as storm water drains, laying over PCC lean concrete and dry bedding mortar (PCC & dry bedding mortar measured and paid seperatly) and jointing/fixing of each panel with ready mix cement mortar as per manufacture instruction and shown typical joint details & Drawings complete all as spd and directed.

Material & Labour for Precast drain of High strength precast reinforced concrete M-50 grade using Fe 500 D grade TMT steel reinforcement bar, drains size 750x750(WXH) U shape, Section of drain shown on drawing , manufactured with high performance self compacting concrete, as per Japanese Industial standers (JIS) confirming to Indian Standards and capable of carrying a wheel load of 2.4 tonnes for light veh movement. Useful for appications such as storm water drains, laying over PCC lean concrete and dry bedding mortar (PCC & dry bedding mortar measured and paid seperatly) and jointing/fixing of each panel with ready mix cement mortar as per manufacture instruction and shown typical joint details & Drawings complete all as spd and directed.

Subtotal

Lump sum price worked out by the tenderer for “RAIN WATER HARVESTING WORKS" as listed in Schedule ‘A’ Section -XII (Part-I)

Schedule ‘A’ Section -XII (Part-I) (RAIN WATER HARVESTING WORKS)

Provision of Environmental Pond with rechage pit of 50000 Glns capacity etc comlete

M&L for loose filling with broken stone or boulder aggregate of gauge 20 as in filter bed complete all as specied.

Subtotal

Lump sum price worked out by the tenderer for “STAND BY DG SETS WORKS" as listed in Schedule ‘A’ Section -XIII (Part-I)

Schedule ‘A’ Section -XIII (Part-I) (STAND BY DG SETS WORKS)

Supply, installation, testing and commissioning of silent Diesel Engine driven generating set to given an output of 100 KVA, 415 Volts. 3 phase, 50 HZ, 4 wire directly coupled to diesel engine, water cooled, turbo-charged after cooled type, mounted on common base plate complete with fuel tank of adequate capacity, vibration damper, other accessories with acoustic enclosure and alternator with AMF Panel complete with latest CPCB norms including PCC foundation etc complete all as specified by the manufacturer and as directed by Engineer-in-charge including comprising of followings :- DIESEL DRIVEN ENGINE . Developing a net directed output 110 BHP or nearest higher suitably marked with alternator to give a net directed output of 100 KVA. The engine shall be capable of delivering the required output at 1500RPM at NTP, Water cooled, turbo-charged after cooled, four stoke, conforming to BS 5514 under NTP conditions with provision of 10 % overload capacity for one hour in every 12 hours including comprising of following :- (i) Fly wheel to suit flexible coupling and fly wheel housing. (ii) Radiator assembly complete with fan water pump and thermostat. (iii) Fuel injection as per manufacturer specification. (iv) Electrical Coil as per manufacturer's instructions/design. (v) 0il filter with mounting arrangements. (vi) Lubricating oil pump and cooler. (vii) Self starter 12 volts. (viii) Exhaust silencer with including cladding with pigeon protection residential type exhaust noise level complying with CPCB norms. (x) Suitable controller with start,stop,Auto/manual,Reset button as per manufacturer instruction. (xi) Engine protection safety device for low lubricating oil pressure, high coolant temperature. (xii) Dynamo/Alternator with over charging protection. (xiii) Batteries 12 volts, 90 AH (Min) or suitable capacity as per manufacturer's design with lead etc- 01 No. maintenance free battery. (B) ALTERNATOR. The engine shall be coupled through flexible coupling to an Synchronous alternator mounted on a strong steel/MS fabricated common base frame suitable for mounting on a permanent foundation. The alternator shall be 3 phase, 50 Hz, 1500 RPM, self excited, self regulating and Brushless type provided with suitable automatic voltage regulator and shall be confirm to BS : 2613 or BS : 5000 and generating 100 KVA output after derating with coupled to diesel engine at 0.8 to 1 power factor lag, 415 volts, 4 wire, AC supply under NTP conditions. The alternator will confirm the following feature. (i) IP 23 protection with H class insulation. (ii) Permissible overload of 10% for one hour in 12 Hour operations (iii) Automatic voltage regulator (AVR) - Fast response electronic Type.(C) AUTO MAIN FAILURE (AMF) CONTROL PANEL : Microprocessor based design/Motorized operated HPL 200 Amp changeover switch and suitable contactor, outdoor type made out of CRCA sheet of 3 mm thick confirming to IS 8623 totally enclosed, dust and vermin proof with front and rear opening, 415 volts, 3 phase, 4 wire, AC 50 Hz having aluminium bus bar of capacity as required to carry current at 110% load of 100 KVA DG Set with three phase and half neutral colour coded, pre wired with aluminium cable of suitable size all as per standard practice of manufacturer specifications with the following accessories :-

(ix) Initial filling of lubricating oil/ coolant and fuel and complete arrangement required for testing will provided by the contractor.

Making hole using treanch less technology under road or hard standing suitable for laying and inserting pipe upto 200 mm bore, any length by mechanical drill system and making the surface good as per existing complete all as specified.

Subtotal

Lump sum price worked out by the tenderer for “FURNITURE WORKS" as listed in Schedule ‘A’ Section -XIV (Part-I)

Schedule ‘A’ Section -XIV (Part-I) (FURNITURE WORKS)

Hexagonal table 8X2

Chair Multi Seater Steel, Make Godrej model MATRIX (FUMTX3XSTRD)/Make : Durian, Model TTRACK3/Make Superq Model Three Seater Settlee Indian (SS 304 Grade)

Chair Executive Revolving Make Durian Model Archer (HB) Make Featherlite, Model Optima (HB)

Bar Stool 3' High Cushioned Make: Nilkamal, Model : Galaxy or its equivalent model in Durian/ Godrej

Plate Rack(Steel) Model: P-348 of make Prayag

Chair Executive Revolving Make: Durian, Model : Archer (HB), Make: Featherlite, Model: Optima (HB)

Display Board (6'x4')

Drugget (3x2 mtr) Make: Zara Carpets or its equivalent.

Stool steel Revolving Adjustable Make: Eezy Model: EEZY 450

Mattress with pillow Make: Sleepwell, Model: Ortho Pro Profiled

Chair CB Steel with Arm & Cushion Make: Eeezy, Model: 399

Chair CB Steel Make: Durian, Model :RICH/37816/CN

Chair Multiseater Steel Make: SuperQ, Model: Three Seater Settee Indian (SS-304 Grade

Chair Barber with Adj Neck Make: JSK Beauty Salon, Model : JBC-01

Mirror Large (4'x2')

Table Conference Make: Durian ,Model: Meridian

Table for Duplicator

Chair umpire Make: Athelitos Sports "Mild Steel Lawn Tennis Umpire chair"

Subtotal

Lump sum price worked out by the tenderer for “PACKAGE TYPE MECHANICAL LAUNDRY WORKS" as listed in Schedule ‘A’ Section - XV (Part-I)

Schedule ‘A’ Section - XV (Part-I) (PACKAGE TYPE MECHANICAL LAUNDRY WORKS)

Supply, installing, commissioning of washing machine, high spin,package type with loading capacity of 25 kg. Front loading open pocket, heavy duty, high spin, top suspension, full stainless steel cabinet, powder/liquid detergent, compartment, electrically heated, stainless steel inner cylinder, outer drum loading door, front SS, Inner basket having three lifter design, single motor with variable frequency inverter drive for various speed for wash, distribution low, normal and high spin, tuned suspension for vibration less performance, fully programmable micro process with fault indication system, solenoid operated water inlet valve, electrically operated (Motorised) drain valve, operates on 415 V 3 phase, 50 Hz AC supply, Make : Fabcare

Drying tumbler electrically heated having loading capacity of 25 kg per charge electrically heated stainless steel body Make - Fabcare

Subtotal

Lump sum price worked out by the tenderer for “INDUSTRIAL RO PLANT FOR DRINKING WATER WORKS" as listed in Schedule ‘A’ Section - XVI (Part-I)

Schedule ‘A’ Section - XVI (Part-I) (INDUSTRIAL RO PLANT FOR DRINKING WATER WORKS)

Supply and install, testing commissioning of Reverse Osmosis water purifier system with SS Frame, High Pressure Pump 2.5HP, Raw Water Pump Microne Filtration 2 Units, Multipot Valve Membrane 40*40 2 Units, Sand and Carbon Filter Vessal 10* 54 dozer Pump, UV Light panel Auto, Flow Meter and Pressure Meter Fittings and Accessories for 500 LPH Capacity RO Plant complete all as specified & directed by Engr-in-Charge.

Supply and Install, testing commissioning of cooling unit for RO water purifier system with SS Frame, 1.5 ton speed Outdoor, 1.5 ton Compressor Kirloskar Copper Coil, Auto Thermostat, Plasto Double Puff Insulated Water Tank 500 Litre, Fittings, Installations and electrical parts for 500 LPH Capacity RO Plant complete all as specified & as directed by Engr-in-Charge.

Cutting of existing water supply main line of 20 mm dia for inserting equal tee 20x20x20 mm for making branch connection and testing complete

Subtotal

Lump sum price worked out by the tenderer for “CONSTRUCTION OF RUNWAY, SHOULDER LINKS TRACKS, DISPERSAL AND LINK WORKS" as listed in Schedule ‘A’ Section - XVII (Part-I)

Lump sum price worked out by the tenderer for “RUN WAY/PARAMETER ROAD , PATH & CULVERTS WORKS" as listed in Schedule ‘A’ Section -XVIII (Part-I)

Lump sum price worked out by the tenderer for “designing and construction of PQC hardstanding (50 m x 30m) Schedule ‘A’ Section -XVIII (Part-II)

Lump sum price worked out by the tenderer for “designing and construction of aircraft appron(arming &de-arming point) with PQC hardstanding as per runway cross section (Area 5000 sqm & RCC traverse walls three sides with minimum height 8.00 m (Total length 200 RM) including earth work for earth filling in traverse) Schedule ‘A’ Section -XVIII (Part-III)

Lump sum price worked out by the tenderer for “designing and construction of aircraft appron (ISOLATION) PQC hardstanding as per runway cross section (Area 2500 sqm & RCC traverse walls three sides with minimum height 8.00 m (Total length 150 RM) including earth work for earth filling in traverse) Schedule ‘A’ Section -XVIII (Part-IV)

Lump sum price worked out by the tenderer for “SUB SURFACE DRAIN RUNWAY WORKS " as listed in Schedule ‘A’ Section - XIX (Part-I)

Schedule ‘A’ Section - XIX (Part-I) (SUB SURFACE DRAIN RUN WAY WORKS)

M & L for providing and laying 200mm thick GSB (Granular Sub Base) Grade-V of table 400-1 of MORTH,IRC specification spreading in layers not exc. 10cm thick, watering, ramming/rolling by tendon vibratory roller and finishing to longitudinal gradient (1:150) and transverse gradient 1.5% for achieve field compaction at least to 98% of MDD(Max Dry Density) of soil complete all as specified.

Geo fabric wrapped around perforated pipe and wrapping trench drain to hold aggregate incl overlap all as specified and directed by Engr-in-Charge.

160mm bore PVC (SWR) semi perforated pipe incl fitting like sockets/coupling, tees etc. laid in trenches all as specified and as directed by Engineer-in-Charge.

160mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches all as specified and as directed by Engineer-in-Charge.

Subtotal

Lump sum price worked out by the tenderer for “RUNWAY LIGHTING WORKS " as listed in Schedule ‘A’ Section - XX (Part-I)

Schedule ‘A’ Section - XX (Part-I) (RUNWAY LIGHTING WORKS)

Dismantling and refixing of uni directional elevated type high intensity runway light fitting suitable for use with 200W 6.6A halogen lamp complete with all accessories including and lamps and lens, lens holder, lens clamping mechanism, pre focus lamp and holder, central column assembly breakable coupling, gasket two pin secondary LEDs, base plate with 6 nos stainless steel nuts/bolts spring and planlln washers complete. (Approach Lights)

Supply and fix Bi-directional elevated type high intensity runway light fitting suitable for use with 200 W 6.6A halogen lamp complete with all accessories including and lamps and lens, lens holder, lens clamping mechanism, pre focus lamp and holder, central column assembly breakable coupling, gasket two pin secondary LEDs, base plate with 6 nos stainless steel nuts/bolts spring and planlln washers complete.(Ruway Edge Lights)

Supply and fix elevated type 45 W medium intensity runway light halogen fitting complete with lamp, omni directional blue lens, lamp holder, lens holder, clamping mechanism, pre focus lamp holder, central assembly, breakable coupling, gaskets two pin secondary LEDs, base plate with 6 nos stainless steel nuts/bolts spring and planlln washers complete.(Taxiway link & Apron Lights)

Supply and Lay AFLS primary Cable of size 6 Sqmm PVC/XLPE insulated, Sheatherd multi strandred copper conductor single core airport lighting cable confirming to IS 1554 complete all as specified.

Supply, laying of Supply, laying of Double wall corrigated Pipe outer dia 50 mm and inner dia 38 mm for cable protction complete all as specified and directed by Engineer -In-Charge

Supply, laying of Double wall corrigated Pipe outer dia 63 mm and inner dia 50mm for cable protction complete all as specified and directed by Engineer -In-Charge

Supply and fix 5 KV grade plug and socket receptacle of type class B connector suitable for field attachment of 6 sqmm 5 KV cable as directed.

Supply and fix 5 KV Grade 50Hz, 200W, 6.6A rating series type isolating transformers encapsulated by polyster resin finally moulded in neoprene type rubber with primary and secondary connection as specified.

Supply and fix 5KV grade 50Hz, 45W, 6.6 A rating series type isolating transformers encapsulated by polyster resin finally moulded in neoprene type rubber with primary and secondary connection as specified.

Supply of FAA complant indoor type microprocessor based, air cooled constant current regulator of thyistor control electroni type suitable for use on 240/415 VAC, 50/60 Hz input AC supply with below mention power at 8.3 Amps with 5 steps variation of current output suitable for local and remote control operation with 24/48 VDC control supply complete with output current indicated on multifunction digital display, Over current, Over voltage earth fault protection and earth fault leakage meter, positive back indication equipment relay contractor etc as required as per specification of capacity 7.5 KVA

Supply of FAA complant indoor type microprocessor based, air cooled constant current regulator of thyistor control electroni type suitable for use on 240/415 VAC, 50/60 Hz input AC supply with below mention power at 8.3 Amps with 5 steps variation of current output suitable for local and remote control operation with 24/48 VDC control supply complete with output current indicated on multifunction digital display, Over current, Over voltage earth fault protection and earth fault leakage meter, positive back indication equipment relay contractor etc as required as per specification of capacity 20 KVA

Supply, installing, commissioning and testing LT panel board CPRI approved (outdoor) cubical type made out of CRCA sheet 3.15mm thick dust and vermin proof with IP 65 protection and angle iron of size 50 x50 x6 mm, pedestal frame grouted in PCC 1:2:4 type B1 20 mm graded stone aggreged thimble and cable entry box with cable glands. Panel should be with front and back locable door and hinges complete with copper bus baar capacity 400 Amps, Three Phase 4 wire (in Separate chamber) busbar rated on epoxt base PVC insulated of height and dia not less than 40mm and preovided wetgh 1100 volt grade heat shrinklable type sleeves and housed in independent chamber having access both from front and back side including painting with powder coated with seven tank process complete all as specified and directed and consisting of the following:-

(a) MCCB 4Pole, 160 Amps, 415 volts 16 KA, ICS = 100% Icu -01 Nos

(b) MCCB 63 Amps, 4 Pole, 415 volts 16 KA, Ics = 100% Icu - 11 Nos

(c) Multifunction meter electronic with suitable CTs, showing Amp, Volt, PF, Hz and other parameter rating Amp up to 200 Amp and Volt up to 500V - 01 No

(d) Internal power and control wiring with suitable size PVC insulated multistranded copper wire

(e) LED indicator lamp (R,Y,B)- 01 Set

(f) Change Over Switch 400 Amp

Dismantling and refixing omni directional elevated type medium intensity runway edge light fitting suitable for use with 200 W 6.6A (White colour) halogen lamp complete with all accessories including and lamps and lens, lens holder, lens clamping mechanism, pre focus lamp and holder, central column assembly breakable coupling, gasket two pin secondary LEDs, base plate with 6 nos stainless steel nuts/bolts spring and planlln washers complete

Dismantling and refixing Uni directional elevated type medium intensity Thrashold/Runway End light fitting suitable for use with 200 W 6.6A (Green/Red colour) halogen lamp complete with all accessories including and lamps and lens, lens holder, lens clamping mechanism, pre focus lamp and holder, central column assembly breakable coupling, gasket two pin secondary LEDs, base plate with 6 nos stainless steel nuts/bolts spring and planlln washers complete

Supply of C.I. Isolating Transformer housing box,water tight round type,metal container of outside size 330mm height 450mm made of 10mm thick cast iron moulding all around except top surface which is 15 mm thick suitable to receive a light fitting base plate on the top and underground housing associated with transformer power cable and having a clear hole centre at one side surface centre 75mm above bottom surface suitable to receive one No. / two of 50mm dia "B" class GI pipe and including check nuts as required and another hole at 175mm from the bottom of the CI Box to receive one no. 15mm dia "B" class GI pipe and check nut as required.The box should have two SS earth bolts of M10 x 40mm and four nuts with washers tapped inside near the hole, alongwith provision of a drain hole at the bottom suitably tapped to receive 15mm dia GI pipe and having clear opening at the top surface and 6 nos. M10 tapped hole at the hole centre to receive fitting base plate and bolts as required. Note : Installation as per below specification:- ITC of CI housing box of size 330 mm dia and depth up to 450 mm as per drawing i/c excavation of hard rock/pavement of all types/ concrete/bitumen etc. and all kinds of soil to the required depth, as per specifications, refilling the side surface, sloping and making good the same as original, providing cement cncrete foundation of ratio 1:3:6 (i cement, 3. coarse sand and 6 graded stone of 40 mm nominal size) & thickness of concrete at 75 mm in all sides i/c bottom dressing of earth, with brick and finishing with 13 mm thick cement plaster of ratio 1:3 on exposed surface and neat cement finishing on top etc. as required. Note : Rate includes the cost of supply of items & its installation at site.

Supply and fix CI Topr Cover 10mm thick with 330mm dia all as specified and directed by Engineer - In Charge.

Subtotal

Lump sum price worked out by the tenderer for “HIGH MAST LIGHT WORKS" as listed in Schedule ‘A’ Section - XXI (Part-I)

Schedule ‘A’ Section - XXI (Part-I) (HIGH MAST LIGHT WORKS)

Supply, laying of Double wall corrigated Pipe outer dia 63 mm and inner dia 50mm for cable protction complete all as specified and directed by Engineer -In-Charge

Making hole using treanch less technology under road or hard standing suitable for laying and inserting pipe upto 100 mm bore, any length by mechanical drill system and making the surface good as per existing complete all as specified.

Supply, installing, commissioning and testing LT panel board (Out door type) cubical type made out of CRCA sheet 3.15mm thick dust and vermin proof and angle iron of suitable size , pedestal frame grouted in PCC (1:2:4) type B-1 20mm graded stone aggregated thimble and cable entry boxes with cable glands. Panel should covered from all sides with front and back lockable door and hinges complete with aluminum bus bar of capacity 63 Amps, TPN, three phase, 04 wire (In separate chamber) including painting with two coats synthetic enameled paint over a coat of red oxide primer and consisting of the following :-

(a) Supply and fix 4 Pole MCCB 40 Amp, 50 Hz, 415 V with rupturing capacity,25 KA with Thermal megnatic relay adjustable type – 01 Nos (incoming)

(b) Supply and fix MCCB 25 Amp, 50 Hz, 230 V with rupturing capacity, 25 KA. – 02 Nos (01 No. Spare) (incoming)

(e) LED Indicated Lamp (R,Y,B) one Set-01

(f) Internal power and control wiring with suitable size PVC insulated multistranded copper wire

Note :- (i) All type of spares such as glands, lugs, nuts, bolts etc, necessary excavation and earthwork, PCC work and making good disturbed surfaces shall deemed to be included in the quoted unit rate. (ii) Drawing of panel shall be approved by GE before fabrication.

Subtotal

Lump sum price worked out by the tenderer for “FENCING/ COMPOUND WALL/SECURITY WALL/GATE WORKS" as listed in Schedule ‘A’ Section - XXII (Part-I)

Lump sum price worked out by the tenderer for “SHIFTING OF EXISTING PIPE LINE (KAVACH CHOWK TO DHANVANTAN CHOWK) WORKS " as listed in Schedule ‘A’ Section - XXIII (Part-I)

Schedule ‘A’ Section -XXIII (Part-I) (SHIFTING OF EXISTING PIPE LINE (KAVACH CHOWK TO DHANVANTAN CHOWK) WORKS

Dismantling and taking up and down or userviciable CI/DI Pipe 450 mm bore any class including making good.

Dismantling and taking up and down or userviciable CI/sluice valve 450 mm bore any class.

Dismantling and taking up and down or userviciable CI/DI special of any size.

Supplying,Laying,Jointing and testing Ductile iron pipe (ISI Marked) Class K-9 bore 450mm confroming to IS:-8329,spigot & socketed ends centrifugally cast suitable for rubber tyton joints complete all as specified and as directed. Note : To be catered for Re-routing of existing pipeline Network. Note:- (a) Rate include cost of laying, excavation, jointing etc (b) Cost of joints(push on tyton joints) including jointing materials shall deemed to be included in the quoted unit rate,nothing shall be paid extra on this account.

Supply and fixing cast Iron sluice valve PN 1.6 (long body) ISI marked confirming to IS: 14846-2000 suitable for 450mm bore pipe,flanged ends,drilled,stainless steel spindle,CI gate with brass ring,iron wheel handle,complete including jointing material such as nuts,bolts,washers and rubber sheet etc complete all as specified and as directed.

Supply and fixing Air release valves with two air outlets 80 mm dia bore ad fixing in DI 450 mm pumping mains line.

Supplying & fixing Ductile iron specials/ fittings of any size, any type like Bends, tapers, increasing, decreasing sockets, tees (Single and double branch), tail pieces and collars etc complete all as specified and as directed.

Material and labour for Construction of brick masonary valve pit chamber size 150 x 150 x 150 cm (internal dimension) using sub class 'B' bricks complete including excavation & earth work, returning fillig and disposal of surplus soil to distance not exceeding 50m and deposited where directed, PCC 1:5:10 type E-2 using 40 mm graded stone aggregate in foundation, coping on top in PCC 1:2:4 type B-2 using 20 mm graded stone aggregate, brick work in cement mortar (1:4), inner plaster 12 mm thick in cm (1:4) finished even and smooth and pionting flush externally as the work proceeds in the same mortar, MS sheet cover 3.15mm thick mounted on angle iron frame of size 40 x 40 x 6mm with handle and locking arrangement duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and embeded portion of MS work duly applying black bitumenous paint before embeded complete all as specified and as directed and shown on drawings.

Material and labour for cutting of road/dismantling of interlocking paver blocks from pathways including excavation and earth work upto required depth complete all as specified and as directed. Note :PCC and interlocking tiles for making good disturbed surface will be measured and paid separetely.

Supply and laying 80 mm thick (M40 grade) precast interlocking tile/paving block factory casted (made by using PVC/ Rubber moulds on Vibrating Table Machine) using grey cement and no pigment, shape haxagon / trigular / zigzag / I-shaped etc, as directed, confirming to relevant IS, having compressive strength not less than 350 Kg/ Sqcm, laid over and including 25mm thick layer of sand and filling the interstices etc with sand complete all as specified and as directed.

Subtotal

Lump sum price worked out by the tenderer for “SHIFTING OF O/H 33/11/0.4 KV LINE (GARUD CHOWK TO MERCURY CHOWK) WORKS " as listed in Schedule ‘A’ Section - XXIV (Part-I) including Sch of credit Rs.395180.00 (minus) as listed in Sch 'A' Sec- XXIII (Part-II)

Schedule ‘A’ Section - XXIII (Part-II) (SHIFTING OF O/H 33/11/0.4 KV LINE (GARUD CHOWK TO MERCURY CHOWK) WORKS)

Dismantling of security lights with Brackets from Existing poles of any size/Description complete all as specified and directed by Engineer-in-Charge.

Supply, laying of Double wall corrigated Pipe outer dia 160 mm and inner dia 136 mm for cable protction complete all as specified and directed by Engineer-in-charge.

Supply, laying of Double wall corrigated Pipe outer dia 90 mm and inner dia 76 mm for cable protction complete all as specified and directed by Engineer-in-charge.

M&L HT 11 KV, 3 phase, 50 cycles totally enclosed metal clad SF6 switchgear having rupturing capacity upto 250 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 400 Amp. complete all as specified and directed by Engr -in-Charge.

Supply and laying 40mm graded stone aggregate inder 2/4 pole structure around the 2/4 structure complete all as specified and directed by Engr -in-Charge.

Supply and fix Cable route indicator (HT) made out of Jodhpurb stone with finished surface all around of size 900X200X150mm with round top duly marked with "HT" by engarving on stone and printed with red synthetic colour including PCC 1:2:4 type B-I using 20mm Graded stone aggregate) of size 30CmX30cmX30cm for embedding stone in ground and necessary earthwork complete all as specified and directed by Engr -in-Charge.

Shifting of 11/0.433KV of capacity 25 KVA to 250 KVA transformers from old location to GE (N) Bikaner fom the place of installation and installing on existing 2/4 Pole structure or platform with necessary fixing arrangement of disconnecting complete all as specified and directed by Engr -in-Charge. Note:- (i) All T & P/ vehicle and manpower for loading, unloading and transporting of transformer shall be arranged by the contractor and the cost thereof shall be deemed to be included in the unit rate quoted. (iii) Cost of transformer oil upto 10 litre required for top up shall be deemed to be included in the unit rate quoted.

Factory made HT 11 KV Junction box panel of size 1200 x 1000 x 500mm made out 3.15mm CRCA sheet powder coated outdoor type dust proof weather proof vermin proof aesthetically designed having IP-65 degree of ingress protection front & rear opening double leaf shutters comprising of colour coded copper bus bar 300 amps TP mounted on 11 KV epoxy insulators including danger notice board made out of 14 Gauge MS sheet of suitable size panel mounted on frame made of 50 x 50 x 6mm angle iron with 1000 mm legs( 550 mm grouted in PCC foundation and 450 mm above foundation including necessary excavation & earth work PCC foundation locking arrangement connecting incoming & outgoing cables with suitable lugs nuts,bolts & washers supply testing installation and commisssioning complete.

Subtotal

Lump sum price worked out by the tenderer for “ARBORICULTURE WORKS " as listed in Schedule ‘A’ Section - XXV (Part-I)

Schedule ‘A’ Section - XXV (Part-I) (ARBORICULTURE WORKS)

Material and labour for preparation of ground and plantation of grass with ‘carpet’ grass including watering and maintenance of the lawn till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed including supplying and spreading of Neem oil cakes, manure or sludge and chemical required for preparation of the ground for plantation of grass. The preparation of ground include surface dressing, uprooting vegetation, shurbs etc, removing boulders, pebbles and leveling the surface flat or in slope complete all as specified and as directed by Engr-in-Charge.

Supply and planting of Hedge (of golden duranta) as directed by Engineer-in-Charge including creation of beds by excavating 60 cm deep and 60 cm wide trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with manure in the ratio 8:1 (8 part of stacked volume of earth after reduction of 20% with 1 part of stacked volume of manure after reduction by 8%) and flooding with water filling with earth if necessary, watering and finally fine dressing levelling etc inclding stacking and disposal of material decleared unserviceable and surplus earth by spreading and levelling as directed within a lead of 50 m and lift upto 1.5 m complete all as specified and as directed.

Supply and planting of following plants in 0.25m to 0.30 poly bags with height as mentioned below including digging holes 1.2m dia x 1.20m deep in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio 2:1 (2 parts of stacked volume of earth after reduction of 20% with 1 part of stacked volume of sludge or manure after reduction by 8%) flooding with water and removal of surplus soil, with & including antitermite treatment using suitable chemicals as required and making 'Thaola' complete all as specified.

(a) Bottle Palm ( Minimum height 4 to 5 feet above ground)

(b) Plumeria ( Minimum height 3 to 4 feet above ground)

(c) Bogounvillia ( Minimum height 3 to 4 feet above ground)

(d) Tikoma ( Minimum height 3 to 4 feet above ground)

(e) Chandani ( Minimum height 3 to 4 feet above ground)

(f) Kaner of white or yellow flower ( Minimum height 3 to 4 feet above ground)

(g) Neem ( Minimum height 4 to 5 feet above ground)

(h) Karanj ( Minimum height 3 to 4 feet above ground)

(j) Gulmohar ( Minimum height 4 to 5 feet above ground)

(k) Ashoka Plant ( Minimum height 4 to 5 feet above ground)

M&L for maintenance of all plants and Grass by weeding, hosing, saucer making once in every month for plants/hedge, once in every 15 days for Carpet Grass / Country Grass / Doob Grass, Burmuda Grass, pruning dried branches once in every week, depositing the material at places as directed by Engineer-in-charge and planting the new plants in place of dead plants of same species and height turing with doods wherever required by replacing the dead plants of grass of any type with same grass as required without any extra cost to the department including water pump operation on daily basis (minimum two hours daily) for watering the plants, Hedges, Shrubbery and Grass and cleaning the filters in drip irrigation system whenever required complete all as specified and as directed.

Supply and fixing Hydrocyclone filter with 2 solid flange size of 75mm dia and capacity of 30 m³/hr for head control unit in drip irrigation system IS 14743:1999 with all connected accessories Complete all as specified and directed by Engineer-In-Charge. Make :- Sourabh shaktiman

Supply and fix PP manifold of size 75mm for Filter Unit of Drip and Pop-up system with connected accessories all complete as specified and directed.

Supply, fixing Ventury with Ferttigation Manifold assemble size of 63 mm for head control unit IS: 14483:1997 with all acessories complete all as specified and directed. Brand-Saurabh Shaktiman

Supply and fixing Air relese valve (plastic) size of 25 mm dia for head control unit in dirip irrigation system. complete all as specified and directed.

Supply and fixing Pressure gauge (glycerine) cap of 0-7 kg/cm² size of 63mm dia for head control unit in dirip irrigation system complete all as specified and directed.

Supply and fixing Screen filter (plastic) with 2 solid flange size of 75 mm dia and capacity of 30 m³/hr for head control unit in drip irrigation system IS : 12785:1994 complete. Brand - Saurabh Shaktiman complete all as specified and directed.

Supply and fixing PP control valve size of 75mm for controlling water in storage tank for drip irrigation system. complete all as per directed.

Supply and fixing PVC pipe (4 kg/cm²) IS ; 4984:2016, size of 90 mm dia for main distribution line in drip irrigation system and including all connected accessories .(ie Socket,Bend,Elbow,Tee,Reducer, connector, Solvent,clamps etc) all as specified and directed by Engineer -In- Charge Make :- Finolex/supreme/Prince/ kisan/Tirupati or eaquivalent.

Supply and fixing PVC pipe (4 kg/cm²) IS ; 4984:2016, size of 75 mm for Main line in Pop-up and Drip irrigation system including all connected accessories. (ie Elbow,FTA,MTA,Tee,Solvent, clamps etc) all as specified and directed by Engineer -In- Charge Make :- Finolex/supreme/Prince/ kisan/Tirupati or eaquivalent.

Supply and fixing PVC pipe (6 kg/cm²) IS ; 4985:2000 size of 63 mm dia for sub distribution line in dirip irrigation system and including all connected accessories (ie Socket,Bend,Elbow, Tee, Reducer,connector, Solvent,clamps etc) all as specified and directed by Engineer -In- Charge Make :- Finolex/supreme/Prince/kisan/Tirupati or eaquivalent.

Supply and fixing PVC pipe (6 kg/cm²) IS ; 4985:2000 size of 50 mm dia for sub distribution line in dirip irrigation system and including all connected accessories (ie Socket,Bend,Elbow, Tee, Reducer,connector, Solvent,clamps etc) all as specified and directed by Engineer -In- Charge Make :- Finolex/supreme/Prince/kisan/Tirupati or eaquivalent.

Supply and fixing Plain lateral 2.5 kg/cm², class II size of 32 mm dia, for water distribution line in dirip irrigation system and including all connected accessories (ie Socket,Bend,Elbow,Tee, Reducer, connector, suitable size Grommat Joiner 16mm take off, End cap, etc) all as specified and directed by Engineer -In- Charge. (For Trees) Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent.

Supply and fixing Plain lateral 2.5 kg/cm², class II size of 16mm dia,online for water distribution line in drip irrigation system including all connected accessories (ie Grommat, Lateral cock, End cap for connection in UPVC/Plain lateral pipe etc) (For trees) all as specified and directed by Engineer -In- Charge. (For Tree) Make :- Finolex/supreme/Prince/kisan/Tirupati or eaquivalent.

Supply and fixing Emitting pipe of dia 16 mm, discharge 2 LPH, dripper spacing 30 cm. 2,5 kg/cm², IS:13488, including all connected accessories (ie Socket,Bend,Elbow,Tee,connector, suitable size Grommat,Joiner etc.(for hedge) all as specified and directed by Engineer -In- Charge. (For Hedges) Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent.

Supply and fixing PVC Control valve size of 75 mm dia for head control unit sub distribution line in dirip irrigation system and all connected accessories complete all as specified and directed Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent

Supply and fixing PVC Control valve size of 63 mm dia for head control unit sub distribution line in dirip irrigation system and all connected accessories complete all as specified and directed Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent

Supply and fixing PVC Control valve size of 90 mm dia for head control unit sub distribution line in dirip irrigation system and all connected accessories complete all as specified and directed Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent

Supply and fixing Flush valve size of 75x63 mm dia for sub distribution line in dirip irrigation system complete all as specified and directed by engineer -In-Charge. Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent.

Supply and fixing PVC service saddle of 50X1/4 mm dia including MT and FT for water distribution line in dirip irrigation system complete all as specified and directed by engineer -In-Charge. Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent.

Supply and fixing push type male threaded adopter size of 32 mm dia for water distribution line in dirip irrigation system complete all as specified and directed by engineer -In-Charge.(For Hedges) Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent.

Supply and fixing PP control valve (Th. End) size of 32 mm dia for sub distribution line in dirip irrigation system complete all as specified and directed by engineer -In-Charge. Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent.

Supply and fixing Dripper cap 8 LPH for dirip irrigation system and connected accessories complete all as specified and directed by engineer -In-Charge. Make :- Finolex/supreme/ Prince/kisan/Tirupati or eaquivalent.

Supply and fixing Swing joint full three way adjustability including neight for Pop-Up Impact Sprinkler, bush with connected accessories, durable polyethylene construction for 3/4" size. Complete all as specified and directed by Engineer -In-Charge.Make Aquaturf

Supply and fixing Pop-Up Impact sprinkler of heavy duty Plastic, adjustable to full-circle or Part circle with diffuser screw for fine drop lets and throw control, inlet size 3/4", having radious of throw up to 12 mtrs at pressure 4 kg/cm² omplete all as specified and directed by engineer -In-Charge. Make Aquaturf.

Supply and fixing PVC End cap size of 50 mm dia for water distribution line in Pop-Up irrigation system and all including complete accessories all as specified and directed.

Supply and fixing Robust top cover with nonslippery grip Plastic heavy duty extended bottom keeps the valve box stable and firmly set in the soil with Green Top and black base Size 10" rectangular shape at Pop-up distribution line and including all connected accessories complete all as specified and directed.

Supply, fixing and testing of Submersible pumpset as per requirement 7.5 HP capacity with supply voltage 415 V, three phase, 50 HZ,with 3000RPM in stainless steel body with inlet filter driven by suitable for operation with operating head 28-14 Mtr and having capacity to discharge water 1.9-0.4 LPS with suction and discharge flanged suction 40 X 40 mm including suitable size of strainer mounted on suitable for existing surface with MS bolts, nuts of required size and necessary control valves, properly connected with suction and delivery water line, including three core copper conductor cable from starter panel to motor terminal as per suitable size including all connected accessories all as specified and directed by Engineer -In -Charge.(Make : CG /Kirloskar/MBH Pumps/KSB/Mather & Platt or equivalent).(One Number working for Adm Block, 01 No. Spare)

Supply, fixing and testing of Submersible pumpset as per requirement 5 HP capacity with supply voltage 415 V, three phase, 50 HZ,with 3000RPM in stainless steel body with inlet filter driven by suitable for operation with operating head 28-14 Mtr and having capacity to discharge water 1.9-0.4 LPS with suction and discharge flanged suction 40 X 40 mm including suitable size of strainer mounted on suitable for existing surface with MS bolts, nuts of required size and necessary control valves, properly connected with suction and delivery water line, including three core copper conductor cable from starter panel to motor terminal as per suitable size including all connected accessories all as specified and directed by Engineer -In -Charge.(Make : CG /Kirloskar/MBH Pumps/KSB/Mather & Platt or equivalent).(One Number working for Adm Block, 01 No. Spare)

Supply anf fix Rotational moulded HDPE water (storage) tank of 5000 Ltrs capacity (Cylindrical vertical tank with closed top) hoisted on roof/ lowered underground and fixed in position including making necessary arrangements for fixing inlet, outlet overflow pipe and provision of washout pipe with and including circular platform of height 30Cm below the tank and base 25Cm more than the external dia of tank casted into two layers of PCC wth first layer of 15Cm thickness of PCC 1:2:4 type B2 using with 40 mm graded aggregate and second top layer 15Cm thickness in PCC 1:3:6 type C1 using with 20 mm graded aggregate with smooth finish to exposed concrete surfaces including necessary form work etc complete all as specified and as directed by Engineer-In-Charge. Note :- (i) The water storage tank shall be tripple layer, HDPE tank moulded to seemless perfection of rotation moulding process.The tanks shall be manufactured only from FDA approved special grade poly ethelene and shall be certified fit for portable water including necessary foundation for placing the water tank.complete all as specified and directed. (Make :- Polycon/ Modi/Ganga/Sintex or eaquivalent). (ii) HDPE storage tank shall be as per IS- 12701. (iii) Necessary Earth work shall be meaasured and paid sepaerately. (02 Nos Tank for Adm Block drip irrigation & 02 Nos For JCOs Mess and ORs living area )

Cutting the existing DI/GI pipe line of 100/200/80 mm bore and inserting the tee / reducer / bend and new connection of GI 50/40/25mm bore pipe complete all as directed.

Supply, fixing and testing of Submersible pumpset as per requirement 5 HP capacity with supply voltage 415 V, three phase, 50 HZ,with 3000RPM in stainless steel body with inlet filter driven by suitable for operation with operating head 28-14 Mtr and having capacity to discharge water 1.9-0.4 LPS with suction and discharge flanged suction 40 X 40 mm including suitable size of strainer mounted on suitable for existing surface with MS bolts, nuts of required size and necessary control valves, properly connected with suction and delivery water line, including three core copper conductor cable from starter panel to motor terminal as per suitable size including all connected accessories all as specified and directed by Engineer -In -Charge.(Make : CG /Kirloskar/MBH Pumps/KSB/Mather & Platt or equivalent).(One Number working for Adm Block for hedges, Trees & Grasses)

Supply and Laying of Double wall corrigated Pipe outer dia 50mm and inner dia 38 mm for cable protection complete all as specified and directed by Engineer-in-Charge.

Subtotal

Lump sum price worked out by the tenderer for “SOLAR WATER HEATER (HOT WATER SUPPLY WORKS" as listed in Schedule ‘A’ Section - XXVI (Part-I)

Schedule ‘A’ Section - XXVI (Part-I) (SOLAR WATER HEATER (HOT WATER SUPPLY WORKS)

Supply & fix Split type heat pump with following components including installation testing and commissioning outdoor air cooled integrated pump with recirculation mode having minimum compressor capacity 1.5/2.0 HP Hermetically sealed with environmental friendly refrigerant at rated heating capacity. The heat pump must be able to deliver hot water at 65 degree celcius (outlet temperature) at the rate not less than 120 litre per hour at water inlet temp of 4 to 60degree celcius and minimum 150-200litre per hour in hybrid mode. The rate of rated uotput heating capacity to rated input power shoul be such that COP of the Machine is not less than 3.0 and must have back up heater power of not less than 6.0 KW and rated power input of not more than 1.3 KW. The heat pump shall have water storage tank capacity (having internal glas lining) not less than 450 Ltre Qty-01 Nos. Supply & fix Pressure pump having SS-304 impellers driven pump having flow of 5000 LPH and head to 30 Mtr with all accessories coupled to motor 1/3 phase 2900 RPM with 60 ltrs of pressure vessel having working standby arrangement (1W) Qty -01 Set Supply & fix Water Heater having Capacity of 455 Ltr with blue diamond glass lined puff injected insulated tank having capacity 455 ltrs, having glass coated electric heating elements to avoid any scaling and 50mm foam insulation. Heating tank should be electrical elements of atleast 6KW in total and should be glass lined. Note :- (i) Heat Pump Should have a user friendly control panel to set the desired temperatutre show casing the actual temperature also with flexibility of installing tha same 15-30 Mtr away from the heat pump. (ii) Heat pump dhoud have the safety protection like high /low voltage, high temperature, refrigerant leak, compressor over heat protection with operational noise level more than 60 Dba

Subtotal

Lump sum price worked out by the tenderer for “FURNITURE WORKS SPL" as listed in Schedule ‘A’ Section -XXVII (Part-I)

Schedule ‘A’ Section -XXVII (Part-I) (FURNITURE WORKS SPL)

Chair Executive Revolving Make: Durian, Model : Archer (HB), Make: Featherlite, Model: Optima (HB)

Chair Steel Cushioned with arms Make: Geeken, Model: GM-226(A) Make: Eeezy, Model: 399

Chair Conference Make: Geeken, Model GP176 (Pure Lather) Make: Godrej, Model Kareena(HB)

Chair Moulded Plastic Ornet Supreme

Filing Cabinet 3 Drawers Make: Godrej, Model : Nova

Table Conference Make: Godrej, Model :Talk (Veneer 10 Seater)

Table Executive Make : Godrej, Model: Finnesse. (Finesse table 6030+ ERU (LHS/RHS)+HDU-4315)

White writing board 6'x4', Make: Alkosign

White writing board 4'x3' Make: Alkosign

Work Table Make: Godrej, Model: Bay work Desk

Subtotal

Lump sum price worked out by the tenderer for “STAND BY ELECTRIC SUPPLY WORKS (E/M)" as listed in Schedule ‘A’ Section -XXVIII (Part-I)

Schedule ‘A’ Section -XXVIII (Part-I) (STAND BY ELECTRIC SUPPLY WORKS)

Supply, installation, testing and commissioning of silent Diesel Engine driven generating set to given an output of 400 KVA, 415 Volts. 3 phase, 50 HZ, 4 wire directly coupled to diesel engine, water cooled, turbo-charged after cooled type, mounted on common base plate complete with fuel tank of adequate capacity, vibration damper, other accessories with acoustic enclosure and alternator with AMF Panel complete with latest CPCB norms including PCC foundation etc complete all as specified by the manufacturer and as directed by Engineer-in-charge including comprising of followings :-(A) DIESEL DRIVEN ENGINE . Developing a net directed output 429 BHP or nearest higher suitably marked with alternator to give a net directed output of 400 KVA. The engine shall be capable of delivering the required output at 1500RPM at NTP, Water cooled, turbo-charged after cooled, four stoke, conforming to BS 5514 under NTP conditions with provision of 10 % overload capacity for one hour in every 12 hours including comprising of following :- (i) Fly wheel to suit flexible coupling and fly wheel housing. (ii) Radiator assembly complete with fan water pump and thermostat. (iii) Fuel injection as per manufacturer specification. (iv) Electrical Coil as per manufacturer's instructions/design. (v) Oil filter with mounting arrangements. (vi) Lubricating oil pump and cooler. (vii) Self starter 12 volts. (viii) Exhaust silencer with including cladding with pigeon protection residential type exhaust noise level complying with CPCB norms. (ix) Suitable controller with start, stop, Auto /manual,Reset button as per manufacturer instruction. (x) Engine protection safety device for low lubricating oil pressure, high coolant temperature. (xi) Dynamo/Alternator with over charging protection. (xii) Batteries 12/24 volts, 180 AH (Min) or suitable capacity as per manufacturer's design with lead etc- 01 No. maintenance free battery. (B) ALTERNATOR. The engine shall be coupled through flexible coupling to an Synchronous alternator mounted on a strong steel/MS fabricated common base frame suitable for mounting on a permanent foundation. The alternator shall be 3 phase, 50 Hz, 1500 RPM, self excited, self regulating and Brushless type provided with suitable automatic voltage regulator.and shall be confirm to BS : 2613 or BS : 5000 and generating 400 KVA output after derating with coupled to diesel engine at 0.8 to 1 power factor lag, 415 volts, 4 wire, AC supply under NTP conditions.

(vii) Thermostat switch inside the acoustic enclosure shall be provided to shut off the DG set in case temperature increases beyond 70 Degree centigrade inside the acoustic enclosure. (viii) Necessary grounding mild steel nuts, bolts, washers etc and anti vibration pad shall be provided by the contractor. (ix) Initial filling of lubricating oil/ coolant and fuel and complete arrangement required for testing will provided by the contractor.

Earthing of Machinery equipment installed at power house/substation using 32X6 mm galvanized MS strip and MS galvanized plates of size 600X600X6 mm as earth electrode

Design supply, install testing & commissioning passengers lift, speed 1.5 metre/sec, lift with single speed motor 415 volts, 3 phase, AC 50 Hz supply conforming to IS14665, suitable to serve G + 04 upper floors with AC Variable Voltage & Variable Frequency drive (VVVF drive) complete with all standard accessories, simplex automatic & manual dual controlled operation with/without attendant, centre opening doors with door drive (electric motor driven mechanism), sliding stainless steel doors, automatic rescue device (ARD) system, 3D infra red sensor in full height of door & built in announcing system without hand set (04 Nos, one each in car, Machine room & near Ground floor landing door) for the Capacity of 06 passenger lift (408 Kg) complete connected accssories for erectioning of the lift complete all as specified

Supply and Fix Alarm sounders / Sirens electronic type horizontal two stage continous normal operation for atleast 50 minutes with sound level 65 db to 120 db Measured at 1.5m with sound output Variation of + 5 db 1000m range

Supply and Fix travelling cable (Flat type) of size 10 sqmm 6 core copper conductor cable for lift from machine room LT panel to Top of the lift

Supply and fix chain Pulley system arrangement for 6 passenger lift to connect steel wire rope fixed with break arrangement.

Supply and fix steel wire rop of thickness of 8mm to 10mm (6X 37 strands) complete all as specified.

Supply, Installation & Commissioning of 50KW Off Grid Solar Photovoltaic Power Plant with MONO Crystalline technology solar modules including 30 Nos of Solar tubular batteries (lead Acid) of 150 AH 12 V, 50KW Solar String Inverter complete all as specified.

Subtotal

Lump sum price worked out by the tenderer for “TREE CUTTING " as listed in Schedule ‘A’ Section - XXIX (Part-I)

NSC Projects Pvt. Ltd. (BID ID -3487527)

Dineshchandra R.Agrawal Infracon Pvt.Ltd (BID ID -3487747)

Brahma Infra (BID ID -3487633)

D R STEEL CONSTRUCTION COMPANY PRIVATE LIMITED (BID ID -3475379)

Som Projects Pvt. Ltd. (BID ID -3475091)

VISHAL INFRASTRUCTURE LTD (BID ID -3487031)