Providing and fixing of decorative street light from Sukhapatnaik chowk to IWSS and BTI of Lakhanpur Area, MCL

Amount

Dismantling of pole / street light standard / strut embedded in brick ballast fondation etc. as required.

Dismantling of overhead lines comprising of copper / aluminium over head conductor, G.I. wire, cross arms, insulators. As required. (i) Conductor - Total Length-8600 mtr ( 6400 mtr- BTI to Sukhapattnaik chowk+2200 mtr from BTI to entry gate)=0.214 x8600 =1840.40 kg (ii) Shackle Insulator - 20 nos.x .744 kg = 14.88kg (iii) Pin Insulator - 158 nos.x .670 kg = 105.86 kg (iv) Bracket - 68 nos.x 8.21 kg = 558.28 kg Total Wt-2519.42 kg

Supply, Insatallation and erection of 10 mtr Designer Pole with single Arm Specification: Part 1:Bottom part GI pole dia-114 mm length-2000mm Thickness-4mm, Part 2 - Top part GI pole dia 89 mm, length-6000mm thickness-3.8mm, Part 3- Arm centre GI pole, Dia-60mm Length 2000mm , Thickness-3.8mm, Part 4 Arm Bend pipe, Dia-42mm, Length-1000mm, Laser cuting sheet used for Arm, MS base plate 300x300x16mm, Aluminium embelllishment decorative part, inbuilt junction Box, Backilite sheet, 4 way connector, 16 AmpMCB, Pu PAINT 120 W street Light Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 Warranty for free replacement (in years) 5,Input operating Voltage range and frequency 140 to 270 V olts AC at 50 Hz+/-2 with auto cutt off at below 120V,LED chip Efficacy ≥130 Lm/Watt, Heat sink should be die-cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes, Operating temperature range -10 deg C to +50 deg C,Short circuit Protection Yes, Over load protecton Yes, Over Voltage protection Yes, Reverse polarity Yes,The luminaire shall be protected against surges and transients ( Internal) >/=5KV, Protection of the entire housing (both LED section and driver section) as per IS:10322 (Part 1):1982 latest IP66, Number of electronic control gear (power supplies) 1 No.,Light Source SMD LED Chip as per LM 80/IS16106,Length of ISI marked three core wire (shall be provided along with supply of material) 100 cm "Manufactures Name and and brand on the aluminium die cast body " Engraved/Embossed LED Make OSRAM / NICHIA / CREE / SAMSUNG / SEOUL / LUMILEDS / PHILIPS / SYSKA / LUMENMAX / EVERLIGHT / EDISON / BRIDGELUX / NATIONSTAR / REFOND/EQUIVALENT LED STRIP 10w LED strip 10 W per mtr using on top of the pole with U profile channel IP67 (6 x 6=12 Mtr) 60W Driver

Supply, Insatallation and erection of 5 mtr Designer Pole with LED strip Specfication: ZIG ZAG decorative rectangular pole single Arm 60W LED, MS steel Pole 142 x 82 mm Thickness 3 mm , MS BASE 250 X250 X10 MM, Inbuilt Junction box . 4 way Connector 6 amp MCB, PU paint with 60 W LED MUDULE, IP 65 LED STRIP 10w LED strip 10 W per mtr using on top of the pole with U profile channel IP67 (6 x 6=12 Mtr) 60W Driver

Supply and Installation of Stylish, Robust, reliable Focus Light with aluminium housing offering uniform light distribution with IP65 Protection suitable to provide accent lighting for a verity of application with surge Protection 4KV, Wattage: 20 W

Supply and installation of Dome Light spherical lighting system with milky white acrylic diffuser 3 mm, IP 66, Al diecast, Wattage: 50W +/- 5%. Voltage Range: 80-300V AC, 50 Hz LED Chip: High power Discrete LED ( CREE/NICHiA/PHILIPS LUMILED) CCT: 3000K-3500K Driver Type: Constant current potted Driver with internal surge protection of 4KV, 10 KV external System Efficacy: >100lm/Watt, IP rating: IP66

Supply and installation of Premium Quality GLOW LED SINEAGE with various informative and awareness messages to be customized as per the direction of engineer incharge, Size 4Ft x 2Ft, attachent to be intigrated with Decorative pole, wiring included.

Supply and installation of High Grade 16X12 MM Aluminium Anodised, with LED (20W/mtr), Driver and all other Accessories, IP66 Grade

Timer based control panel comprising 3 phase 100 A Contactor and all other suitable assecories as per the instruction of engineer in charge

Suitable Feeder Panel for 70 Sq mm in and 35 sq mm, 70 sq mm out Comprising of BUS BAR (3P+1N+1Earth) and other acessories as required

Main control panel comprising 3 phase 200 A MCCB in incoming with suitable busbar for 70 sqmm cable output comprising digital voltmeter, ammeter, phase indicator and all other suitable assecories as per the instruction of engineer in charge

Providing of 70 sq.mm. four core 1.1 kv grade alumunium armoured cable.

Providing of 35 sq.mm. four core 1.1 kv grade alumunium armoured cable.

Providing of 25 sq.mm. four core 1.1 kv grade alumunium armoured cable.

Providing of 16 sq.mm. four core 1.1 kv grade alumunium armoured cable.

Providing of 10 sq.mm. four core 1.1 kv grade alumunium armoured cable.

Providing of 2.5 sq.mm two core LT copper cable 1.1 Kv grade

Laying of one number PVC insulated and PVC shethed / XLPE power cable of 1.1 KV grade above 35 sq.mm . up to 100 sq mm direct in grund including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.

Laying of one number PVC insulated and PVC shethed / XLPE power cable of 1.1 KV grade up to 35 sq.mm . direct in grund including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.

Excavation for cable trenches of soft soil, depth uoto 1.2 m including dressing of sides lift upto 1.5 m, including getting out the excavated soil refilling with sand and or good soil after laying of cable/ pipe etc in layers of 20 cm, ramming, watering and disposal of surplus excavated soil as directed, within a lead of 50 metres.

Providing, laaying and fixing 100 mm. dia G.I. pipe (medium class) in ground complete with G.I. fitting trenching (75 cm deep ) and re- fitting atc required

Providing of HDPE pipe inner dia 50 mm

Providing of HDPE pipe inner dia 110 mm

Earthing with G.I. earth plate 600mm X 600mm X 6mm thick including accessories, and providing masonary enclosure with cover platee having locking arrngement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and laying position cement concrete 1:2:4 (1 cement:2 coarse sand : 4 graded stone arggregate 20 mm nominal size) in fondation of pump, DG set etc . Including form work etc as required.

Providing and laying position RCC 1:1.5:3 (1 cement:2 coarse sand : 4 graded stone arggregate 20 mm nominal size) in fondation of Pole having Decorative Base as per the design

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.-Thermo-Mechanically Treated bars of grade Fe-500D or more.

Demolising of Concrete

Total impact of GST for the purpose of CTC