Repair/maint of MT Veh, DG Sets and misc items under AGE E/M at GE NAMS

Amount

To depute service representative minimum for 01 visit to attend the DG set at frequency as per schedule or after 250 working hours. Service Representative will Carry scheduled preventative maintenance checks on Diesel Generating Set (of any make ) and carry out the the undermention Jobs during his visit for DG Set 25 KVA to 30 KVA.

(A) Check List for minimum core of work

(i) Check the sample of coolant concentration

(ii) Check the fan belt for tension and inspect it. If needs any replacement

(iii) Check the exhaust mani fold out let

(iv) Examine the charge level of the battery and check for any loose connection

(v) Check the air cleaner components and clear them if any dirt occures

(vi) Check and adjust the voltage level of the battery charger

(vii) Drain out water from the container of the bottom of the filter housing and fuel tank

(viii) Checking of control panels wiring, instrumentation, contactor fuses etc.

(ix) Check the serviceability of safety controls of engine

(x) Checking of all electrical connections for its proper tightness

(xi) Check AVR connections & power cable connections for tightness

(xii) Check the RPM/frequency and adjust it.

(xiii) Check the condition of wire breaded/nonbreaded hoses of engine.

(xiv) Checking of load balancing of alternator/AMF panel output

Note (A) - In addition to above the following checks/repair will be carried out by service representative for six monthly/Yearly

(a) Check by every six months:-

(i) Replace the diesel fuel filter & Oil filter

(ii) Clean the crank case breather

(iii) Check the radiator hoses

(b) Check by Yearly:-

(i) Greasing of Alternator bearing

(ii) Checking of exhaust back pressure

(iii) Checking of temperature of exhaust

(iv) Checking of radiator performance check

Note B - Repair under above item does not include overhauling /top overhauling / PT Pump & Injectors calibration/ replacement of major parts/ rewinding of Alternator, or repairs on breakdown of the DG set

(i) Assure trouble free performance of DG set

(ii) To pre-intimate engine repair needs/ overhaul based on engine parameters.

(iii) if in case any brakedown the service engineer attened the brake down immiediately and make the DG set serviceable with in 24 working hours.

All as per srl item no 2 above but DG set of cap 40 to 65 KVA

All as per srl item no 2 above but DG Set of cap 100 to 250 KVA

Supply only in replacement the fwg item of company approved make for DG Set of cap 25 to 30 KVA

Diesel fitter.

Lub oil filter.

Radiator hose pipe set.

Fan belt.

Air filter element

Supply only in replacement the fwg items of company approved make for DG Set of cap 40 to 65 KVA

Diesel fitter.

Lub oil filter.

Radiator hose pipe set.

Fan belt.

Air filter element

Supply only in replacement the fwg item of company approved make for DG Set of cap 100 to 250 KVA

Diesel fitter.

Lub oil filter.

Radiator hose pipe set.

Fan belt.

Air filter element

Dis-connecting the fuel pipes from the Fuel Injection Pump Assembly, taking out the FIP assembly from the engine body and transporting to the MICO authorized dealer to carry out the following for DG of 25 to 30 KVA (a) Dis-mantling the complete FIP, taking out all the parts, cleaning the internal/external surfaces of the pump (b) replaceing the suction & delivery valves, rollers and other worn out parts. (c ) Assembling the parts, filling correct grade of oil ,testing for smooth functioning. (d) Calibrating the FIP for correct fuel pressure on the MICO machine (e) Transporting the FIP from the workshop to site and fitting the FIP assy to the engine and testing at load to the entire satisfaction of Engineer-in-charge.

Dis-connecting the fuel pipes from the Fuel Injection Pump Assembly, taking out the FIP assembly from the engine body and transporting to the MICO authorized dealer to carry out the following for DG of 40 to 65 KVA (a) Dis-mantling the complete FIP, taking out all the parts, cleaning the internal/external surfaces of the pump (b) replaceing the suction & delivery valves, rollers and other worn out parts. (c ) Assembling the parts, filling correct grade of oil ,testing for smooth functioning. (d) Calibrating the FIP for correct fuel pressure on the MICO machine (e) Transporting the FIP from the workshop to site and fitting the FIP assy to the engine and testing at load to the entire satisfaction of Engineer-in-charge.

Dis-connecting the fuel pipes from the Fuel Injection Pump Assembly, taking out the FIP assembly from the engine body and transporting to the MICO authorized dealer to carry out the following for DG of 100 to 250 KVA (a) Dis-mantling the complete FIP, taking out all the parts, cleaning the internal/external surfaces of the pump (b) replaceing the suction & delivery valves, rollers and other worn out parts. (c ) Assembling the parts, filling correct grade of oil ,testing for smooth functioning. (d) Calibrating the FIP for correct fuel pressure on the MICO machine (e) Transporting the FIP from the workshop to site and fitting the FIP assy to the engine and testing at load to the entire satisfaction of Engineer-in-charge.

M & L for draining out old engine oil from the DG Set and replace with new oil at recommended by manufacturer complete all as specified and directred.

Repair overhalling of self starter including replacement of worn out clutch assembly bush, spring, plunger assembly ,solenide switch, corbon brushs, spring etc for the following DG set.

(a) 25 KVA to 30 KVA

(b) 40 KVA to 65 KVA

(c) 100 KVA to 250 KVA

M & L for topping up of water coolent in radiotor of DG set TVS Girling/volvo line or of equivelent make all as directed by EIC.

Cleaning of the fuel tank of DG sets of following capacity after decaning the diesel, through cleaning with kerosene oil including replacement of level indicator pipe complete all as directed by EIC.

(i) 25 KVA to 30 KVA

(ii 40 KVA to 65 KVA

(iii) 100 KVA to250 KVA

Dismantling and removing of water pump assesmbly complete from the engine repair/overhauling the same by replacing worn out components like bearing,impeller,bushes,oil seal,water seal,gasket etc. reassembling,refixing and testing complete for the following :-

(i) 25 KVA to 30 KVA

(ii) 40 to 60KVA

(iii ) 100 KVA to 250 KVA

Reapair/overhaling of dynamo/ charging alternator including replacement carbon,brushesholder,spring,commutator/slipring assembly bearing,regulator etc. of any make,type and capacity.

Supply and fix in replacement of automatic voltage regulator suitable for DG set of following rating :-

(i) 25 KVA to 30 KVA

(ii) 40 KVA to 63 KVA

(iii ) 100 KVA to 110 KVA

M & L for replacement of electrically operated fuel shut down valve assembly for 25 to 250 KVA DG set complete testing and commissioning as specified and directed by EIC.

M & L for replacement of moulded rectifier assembly complete as per exisiting one of 25 to 250KVA alternator excitor unit complete all as specified & directed .

M & L for replacement of PVC flexible wire breded fuel pipe suitable for Gen set of capacity 25 KVA to 250 KVA complete all as specified & directed .

Dismantling of radiator of DG set and transporting to work shop for servicing/cleaning with dismantling twin tanks, replacement of gasket packing , nuts ,bolts , washers ,descaling with appropriate chemical and welding copper brazing of damazed fins/tubes and reassembling & refixing of following capacity in same position after testing complete all as specified & directed .

(i) 25 KVA to 30 KVA

(ii) 40 KVA to 65 KVA

(iii) 100 KVA to 250 KVA

M & L for replacement of flexible rubber cuopling suitable for DG set 25 KVA to 110 KVA complete all as specified & directed .

M & L for replacement of engine start relay 12/24 Volts. Make:- PIC / Technica/ Indo Econ complete all as specified & directed .

Repair to battery 12 Volt 180 AH including removing of old cell/plate and supply and replacement of positive plate /cell and negative plate / cell filling of electrolight 1150 gravity chargeing fix on gen and taking complete all as spd and directed by EIC.

M & L for replacement of battery terminals brass with steel nuts, bolts & washers .

M & L for replacement of PVC insulated battery lead stranded copper conductor of size 50 Sq mm suitable pices with bothend copper lugs complete all as specified & directed .

Painting of DG set by scrapping of old paint complete and painting with two coats of synthetic enamel paint over a coat of red oxide primer and writing SM/MES No of fwg size complete all as specified & directed.

(i) 25 KVA to 30 KVA

(ii) 40 KVA to 65 KVA

(iii) 100 KVA to 250 KVA

Dismantling of exhaust mani fold assembly complete and repairing, cleaning complete with wire brush necessary welding and refixing with required new bolts/nuts complete all as directed for DG set of 25 KVA to 250KVA Capacity.

Taking out the old rusted silencer in beteween exhaust pipe engine and providing new low noise silencer (Residential type) and fixed with gasket, nutbolts washer and asbestoss rope complete all as specified and directed for DG set of 25 KVA to 250KVA Capacity.

Taking out the old rusted silencer in beteween exhaust pipe engine and providing new low noise silencer (Residential type) and fixed with gasket, nutbolts washer and asbestoss rope complete all as specified and directed for DG set of 25 KVA to 250KVA Capacity.

25 KVA to 30 KVA

40 KVA to 65 KVA

100 KVA to 250 KVA

M & L in replacement for Changeover switch 200 Amp off load side handle 4 pole, 415 Volt complete all as specified & directed . MAKE : STANDARD

M & L in replacement for Changeover switch 63 Amp off load side handle 4 pole, 415 Volt complete all as specified & directed . Make : Havells

M & L in replacement for Changeover switch 100 Amp on load side handle 4 pole, 415 Volt complete all as specified & directed . Make : Havells

M & L in replacement for Changeover switch 200 Amp on load 4 pole, 415 Volt complete all as specified & directed . Make : Standard

M & L in replacement for 63 Amp MCCB, 4 pole, 25 KA , 415 Volt complete all as specified & directed . Make : Havells/L&T

M & L in replacement for 100 Amp MCCB, 4 pole, 25 KA , 415 Volt complete all as specified & directed . Make : Havells/L&T

M & L in replacement for 250 Amp MCCB, 4 pole, 35 KA , 415 Volt complete all as specified & directed . Make : Havells/L&T

M & L in replacemet of control wiring of DG Set as per existing size of copper wire connected complete to the panel with provision of all wiring codes all as reqd insert the panel.

Supply only distilled water for battary complete all as specified & directed.

Supply and fixing in replacement of asbestoss rope for exhuest pipe complete all as specified & directed.

M & L for in replacement of fuel tank cubical/cylindrical type made up of 2mm thick MS sheet for accomodating 200/250 ltrs diesel complete all as specified & directed.

Dis-connecting the alternator from the engine by removing the coupling, transporting the alternator complete to authorized maintenance service center for repairs: upto 63 KVA (a) Rewinding and Cleaning the armature complete, applying one coat of varnish and heating complete (b) replacing the damaged rectifier unit including filter circuit elements complete. (c ) replacing the wornout carbon brushes – 01 set Assembling the alternator complete at workshop and testing at NO load , transporting the same to the site , connecting the alternator to the engine after proper alignment including replacement of coupling , key and testing and commissioning complete all as directed by the engineer in charge.

Dis-connecting the alternator from the engine by removing the coupling, transporting the alternator complete to authorized maintenance service center for repairs: 100 to 250 KVA (a) Rewinding and Cleaning the armature complete, applying one coat of varnish and heating complete (b) replacing the damaged rectifier unit including filter circuit elements complete. (c ) replacing the wornout carbon brushes – 01 set Assembling the alternator complete at workshop and testing at NO load , transporting the same to the site , connecting the alternator to the engine after proper alignment including replacement of coupling , key and testing and commissioning complete all as directed by the engineer in charge.

M & L for scraping the existing paint of Canopy of DG set , Cleaning the rusted portion complete , and applying two coat colour of existing paint all as required at site upto 63 KVA.

M & L for scraping the existing paint of Canopy of DG set , Cleaning the rusted portion complete , and applying two coat colour of existing paint all as required at site from 100 to 250 KVA .

Repair/maint of EOT crane 5.00 Ton/ 2.00 Ton cap in frequency of every 6 months ,checking of control panel, control wiring, gear box, limit switches horizontal/Cross / Up / down travel, motors gear box etc including oiling, greasing, load testing complete all as specified and directed by Engr-In-Charge.

Supply & fix in replacement travelling cable copper conductor 03 Core 6 Sqmm

Do as per ser No 49 but 4 Sqmm

Supply and fix in replacement of control panel comprising of the fwg:-

Contactor 415 volt, 32 Amp, 03 pole- 06 Nos.

Timer switch- 02

Relay- 02 Nos

Control panel wiring- 01 Job

Supply and fix in replacement of limit switch

Supply and fix in replacement of wire rope 3/4" dia

Supply and fix in replacement of wire rope 1/2" dia

Taking out electric motor 2 HP dismantling , taking out burnt winding wire and rewinding with new supper enameld copper wire baking, vernishing etc and reassembling testing complete.

Taking out electric motor 3 HP dismantling , taking out burnt winding wire and rewinding with new supper enameld copper wire baking, vernishing etc and reassembling testing complete.

Supply and fix in replacement of bearing suitable for 2 HP motor

Supply and fix in replacement of bearing suitable for 3 HP motor

Supply and fix in replacement of long travel shaft pillar block bearing as per existing size.

Supply and fix in replacement mannual operated suspended type control switch panel consisting of push botton 08 Nos for up/down, reverse, fwd, start and stop.

Servicing/reparing of 75 KVA to 100 KVA 3 Phase, 415 Volt servo voltage stablizer complete including disconnecting the all connection and taking out old UNSV item, cleaning and servicing the fixed/moving contract and blowing and dust and providing the proper size of lugs, nuts and bolts and new control wiring and replace of the fwg items including transporting to workshop and return back after repair complete all as specified and directed (Note: Materials/parts for replacement will be measured & paid seprately.

Material and labour for disconnecting /opening the UNSV variable transformers of 75KVA to 100 KVA and rewinding the variable transformers with super enamelled copper winding as per existing gauge including insulations material cotton tape, varnish , insulation paper, sleves and drying/baking to proper temparature complete all as specified and directed.

Supply in replacement of PCB circuit board relay etc complete all as specified and directed.

Supply in replacement of LT bushing male/Female complete all as specified and directed.

Servicing/reparing of 30 KVA to 50 KVA 3 Phase, 415 Volt servo voltage stablizer complete including disconnecting the all connection and taking out old UNSV item, cleaning and servicing the fixed/moving contract and blowing and dust and providing the proper size of lugs, nuts and bolts and new control wiring and replace of the fwg items including transporting to workshop and return back after repair complete all as specified and directed (Note: Materials/parts for replacement will be measure and paid seperatley

Material and labour for disconnecting /opening the UNSV variable transformers of 30 KVA to 50 KVA and rewinding the variable transformers with super enamelled copper winding as per existing gauge including insulations material cotton tape, varnish , insulation paper, sleves and drying/baking to proper temparature complete all as specified and directed.

Supply in replacement of PCB circuit board relay etc complete all as specified and directed.

Supply in replacement of LT bushing male/Female complete all as specified and directed.

Supply filling and topping of new transformers oil low viscocity type of die electric strength 35 to 40 KV breaking cap conforming to IS complete for outdoor/indoor types stablizer complete all as specified and directed.

Dehydration of old transformers oil by heating and making breaking cap upto 35 KV complete all as specified and directed.

Repair to self starter including taking out from veh Tata Xenon 207 dismantling including supply and replacement of the fwg spares parts, reassmbling, commissioning and testing all as directed by Engr-In-Charge:-

Solonoid switch

Self armature

Copper brush set

Re-tapping of field coil

Repair to self starter including taking out from veh EICHER dismantling including supply and replacement of the fwg spares parts, reassmbling, commissioning and testing all as directed by Engr-In-Charge:-

Solonoid switch

Self armature

Copper brush set

Re-tapping of field coil

Repair to self starter including taking out from veh Car Ambassador dismantling including supply and replacement of the fwg spares parts, reassmbling, commissioning and testing all as directed by Engr-In-Charge:-

Solonoid switch

Self armature

Copper brush set

Re-tapping of field coil

Re-tapping of field coil

Repair to clutch system including dismantling and supply & replacement of fwg spares/parts including reassembling and testing complete all as specified and directed:-

(a) TATA XENON 207/EICHER

(i)Clutch plate

(ii)Pressure plate

(iii)Clutch release bearing

(iv)Clutch cylinder lower

(V)Clutch cylinder upper

(b ) CAR AMBASSADOR

(i)Clutch plate

(ii)Pressure plate

(iii)Clutch release bearing

(iv)Clutch cylinder lower

(V)Clutch cylinder upper

Repair to rediator by dismatling and taking out rediator from vehicle including opening of upper tank and lower tank and rectify the leakage by gas welding of copper tube and cleaning of rediator tube with acid and re- assembling the same after testing and commissioning complete all as specified and directed for TATA407/TATA 207.

Repair to rediator by dismatling and taking out rediator from vehicle including opening of upper tank and lower tank and rectify the leakage by gas welding of copper tube and cleaning of rediator tube with acid and re- assembling the same after testing and commissioning complete all as specified and directed for EICHER.

Repair to rediator by dismatling and taking out rediator from vehicle including opening of upper tank and lower tank and rectify the leakage by gas welding of copper tube and cleaning of rediator tube with acid and re- assembling the same after testing and commissioning complete all as specified and directed for Car Ambassador.

Dismantling and taking out defective water pump from veh EICHER supply and fix new water pump after testing and commissioning complete all as specified and directed.

Dismantling and taking out defective water pump from veh Car ambassador supply and fix new water pump after testing and commissioning complete all as specified and directed.

Repair to suspension system including supply and replacement of the fwg for EICHER :-

(i)Suspension bush kit

(ii)Tie rod end rod set

(iii)Ball joint

(iv)Shock absorbers make: Gabrial

Repair to suspension system including supply and replacement of the fwg for Car Ambassador:-

(i)Suspension bush kit

(ii)Tie rod end rod set

(iii)Ball joint

(iv)Shock absorbers make: Gabrial

Taking out defective silencer assembly and replacing the same with new for TATA-207/407/EICHER/Car Ambasdor including replacing of the following parts complete all as specified and directed.

(i)Crown wheel pinion

(ii)Bewel for differential system

(ii)Yoke and teeth

Repair to differential system including taking down UNSV defective part and supply and replacement of the fwg for TATA Xenon/207:

(i) wipper machine with motor

(ii) Ignation switch with key set

(iii)Indicator/ brake light assembly

(iv)Head light assembly

(v)Fog Light

(vi) Alternator assembly complete

(vii) Door lock assembly

(viii)Light and left mirror

(ix) Mud flap

(x)Horn assembly complete set

Repair and replacement including taking UNSV defective parts and supply and fixing the fwg for EICHER:-

(i)wipper machine with motor

(ii)Ignition switch with key set

(iii)Head light assembly

(iv)Fog Light

(v)Alternator assembly complete

(vi)Right and left mirror

(vii)Mud flap

(viii)Glass winder

(ix)Door lock assembly

(x)Indicator/brake light assembly

Repair and replacement including taking UNSV defective parts and supply and fixing the fwg for Car Ambassador:-

(i)Wipper machine with motor

(ii) IgnItion switch assembly

(iii)Head light assembly

(iv)Fog Light

(v)Complete altenator assembly

(vi)Right and left mirror

(vii)Mud flap

(viii) Glass winder

(ix)Cut out fuse

(x)Fuel pump assembly

(xi)Petrol pipe

(xii) Door lock assembly

(xiii) Indicator/ brake assembly

Taking out fuel pump assembly and calibration with authrised wksp and re-fixing the same after testing and commissioning complete all as specified and directed for EICHER.

Taking out fuel pump assembly and calibration with authrised wksp and re-fixing the same after testing and commissioning complete all as specified and directed for Car Ambassador.

Removing old paint of veh cabin body, bumper, bounet & metalic surface with the help of blow lamp and rubbing with sandy paper complete all as specified and directed for EICHER.

Removing old paint of veh cabin body, bumper, bounet & metalic surface with the help of blow lamp and rubbing with sandy paper complete all as specified and directed for Car Ambassador.

Making good surface by denting welding patch work and apply putty prepared mettalic surface for paint for paint complete all as specified and directed for EICHER.

Making good surface by denting welding patch work and apply putty prepared mettalic surface for paint for paint complete all as specified and directed for Car Ambassdor.

Painting complete body of vehicle with two coat of red oxide paint and two coat of enamel paint with spray painting complete all as specified and directed for EICHER.

Painting complete body of vehicle with two coat of red oxide paint and two coat of enamel paint with spray painting complete all as specified and directed for Car Ambassador.

Taking out UNSV driver cabin seat assembly from veh repair the seat with the help of welding/replacing spring nut bolts etc and replacing and fixing new foam and superior quality rexine cloth and refixing the same to veh complete all as specified and directed for Veh TATA Xenon 207/EICHER

Taking out UNSV driver cabin seat assembly from veh repair the seat with the help of welding/replacing spring nut bolts etc and replacing and fixing new foam and superior quality rexine cloth and refixing the rear and front seat assembly same to veh complete all as specified and directed for Veh Car Assembly.

M & L in replacement of seat cover for rear seat and front seat complete all as specified and directed for Car Ambassador.

M & L in replacement for foot mat set complete all as specified and directed for TATA Xenon 207/EICHER.

M & L in replacement for foot mat set complete all as specified and directed for TATA Xenon 207.

M & L in replacement for foot mat set complete all as specified and directed for Car Ambassador .

Repair overhauling to 4 wheel brake assembly including replacing the fwg for EICHER complete all as specified and directed:-

(i)Wheel cylinder assembly

(ii) Break shoe assembly set of two

(iii) Front wheel disc brake set

(iv) Brake master cylinder

Repair overhauling to 4 wheel brake assembly including replacing the fwg for Tata Xenon /Car Ambassador complete all as specified and directed:-

(i)Wheel cylinder assembly

(ii) Break shoe assembly set of two

(iii) Front wheel disc brake set

(iv)Brake master cylinder

Servicing of veh including cleaning nipple gresing, engine tune up valve setting and replacing the fwg :-

(i)Oil filter

(ii)Diesel filter

(iii)Air filter

(iv) Wheel bearing

(v)Computer wheel alisgment

(vi) Testing of PUC certificate from authorized civil Govt Authority

(vii)Front/rear wheel hub greasing

Differential system oil 90 grade

Radiator coolent

Repair to name/number plate front/rear by replacing the UNSV number plate made out from MS Sheet duly writing of unit name, BA No, formation sign, Bdg classification in redium letter in front and rear side of veh.

M & L for replacement of old engine oil from the vehs and cleaning the oil sump throughly supply & filling new engine oil grade 20W 40 of Make : Servo super of Indian Oil all as specified and direcred by Engr-In Charge.

Repair to motor cycle including repair/replacement of fwg items:-

(i) Air Filter

(ii)Clutch plate

(iii) Clutch chain

(iv) Main chain

(v) Clutch housing

(vi) Gear assembly

(vii) Indicator light

(viii)Horn

(ix)Brake show

(x)Clutch wire

(xi) Mud guard rear

(xii)Battery Exide dry type

(xiii)Brake wire

(xiv) Mud guard front

Repair to aluminium ladder cabin / folding type trolley mounted of height 32/27 feet :-

(i)Removing the existing rusted/broken angle iron - 01 Job

(ii)Supply and welding new MS Angle iron of size 50 x 50x 5mm - 30 Kg

(iii)Taking out single drum winch with pully assembly with wire rope and repair/replacement - 01 Job.

(iv)Supply and fixing in replacement wire rope of size 1/5" dia - RM

(vi)Taking out 04 wheels with shaft and replacing with eixting size- 04 Nos.

Dismantling of electric motor for rewinding with supper enameled copper wire of suitable gauge and complete servicing of compressor and reassembling the same after repair/replacemnet of fwg parts:-

Pressure gauge- 01 Nos

Pressure air pipe- 01 Nos

Gate valve- 01 Nos

Fan Belt- 01 Nos

Scrapping and rubing with emery paper of complete body air compressure and painting of air compressure with one coat of red oxide and two coat of enameled paint complete all specified and directed.

Dismantling of electric motor for rewinding of air compressure with supper enameled copper wire of suitable gauge and complete servicing of compressor and reassembling the same after repair/replacemnet of fwg parts:-

(i)Air filling pipe, 3 ply heavy duty dia 6 mm suitable for Air compressor - 10 RM

(ii)Brass nozel- 01 Nos

(iii)Pressure guage - 01 Nos

Rewinding of battery charger with supper enameled copper wire of suitable gauge and complete servicing of battery charger complete all as specified and directed:-

Taking out outer cover from vehicle,shifting to workshop and rethreadind of suitable size,shape and guage including reassembling the same after repair complete all as specified and directed of size 165R/80-15 R.

Taking out outer cover from vehicle,shifting to workshop and rethreadind of suitable size,shape and guage including reassembling the same after repair complete all as specified and directed of size 215R/75-16 R.

Taking out outer cover from vehicle,shifting to workshop and rethreadind of suitable size,shape and guage including reassembling the same after repair complete all as specified and directed of size 7.50x16.

Supply and fixing inreplacement of inner tube with rubber ring complete size 165R/80.

Supply and fixing inreplacement of inner tube with rubber ring complete size 215R/75.

Supply and fixing inreplacement of inner tube with rubber ring complete size 7.50x16.

Material and labour for recondioning of lead acid battery capacity 80AH complete all as specified and directed.

Material and labour for recondioning of lead acid battery capacity 100AH complete all as specified and directed.

M/s Vijay Construction Co.

P S BUILDERS

v k constructions co