PROVN OF DRAINAGE CULVERTS FOOTPATH AND OTHER ALLIED WORKS NEAR AIR ENCLAVE AND CERTAIN SANCTIONED WORKS AT BAMRAULI

Amount

Surface excavation exc 30 cm deep and averaging 15 cm deep in soft/ loose soil complete all as specified and directed.

All as per Sl Item No.1 above but Add to (or deduct from) for every 3 cm or part thereof above or below 15 cm average depth for complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

M & L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone agg) as in foundations, filling and mass concrete and below plinth beam complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, for rough finish flat surface at concrete complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished square, rectangular or polygonal surfaces of concrete complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, for fair finished surfaces of concrete complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished flate surfaces of concrete complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for fair finished surfaces of concrete complete all as specified and directed.

M&L for RCC M-25 Design Mix (Using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etcbasement slabs, under-reamed piles and mass concrete etc complete all as specified and directed.

M&L for RCC M-25 Design Mix (Using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L for RCC M-25 Design Mix (Using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.

M&L for RCC M-25 Design Mix (Using 20mm graded stone aggregate) as in chajjas etc complete all as specified and directed.

M&L for RCC M-25 Design Mix (Using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L Mild steel TMT bars of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M & L for Brick work with sub class 'B' bricks, straight or curved on plan 6m mean radius built in cement mortar 1:6 etc complete all as specified and directed.

M & L for rendering 5 mm thick in cement mortar 1:3 on fair faces of concrete surface as in ceilings finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces or brick work or concrete surfaces, finished even and smooth without using extra cement and mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note: WPC will be measured and paid separately under respective item.

M&L for Preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for Preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for screed bed 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete roof surfaces, finished even and smooth without using extra cement and mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note: WPC will be measured and paid separately under respective item.

M&L for APP based polymeric membrance minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150gms/Sqm) land on primed surfaces by applied over a coat of blown bitumen 85/25 shall be applied @ 1.20 Kg/Sqm over and including one coat of primer @ 0.50 Kg/Sqm including cleaning of roof surface free from loose particles complete all as specified.

Supply only integral water proofing compound as per relevant IS of approved make complete all as specified and as directed.

M & L for 100mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub-base of floorings complete all as specified directed.

M&L for 100mm thick cement concrete 1:2:4 type B-2, using 40mm graded aggregate as in flooring etc complete all as specified and directed.

M&L for 150mm thick sand cushion/filling under floors including spreading, levelling and compaction complete all as specified and directed.

M & L for hard core of not exceeding 63 mm gauge deposited, spread, and levelled in layers n exc 150 mm thick , watered and rammed to a true surface complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C2 ( Using 40mm graded stone aggregate) for plinth protection finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing etc complete all as specified and directed.

M&L for mild steel, plain, black sheet 0.63mm thick in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

S&F steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded etc complete all as specifed and directed.

S&F 3mm thick sheet glass ordinary quality glazing with oil putty in square n exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for preparing new or previously untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate for filling holes in walls, bed blocks, fixing holdfast, coping etc including all necessary form work complete all as specified and directed. Note :- The rate is deemed to be inclusive of necessary form work.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50 m and dpositing at a level not exceeding 1.5 m from starting point complete all as specified and directed.

M&L for Machine pressed rubber moulded, colored, precast concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 80 mm thickness and grade of concrete shall be M-40 complete all as specified and directed. Note : Paver blocks shall be tested in NABL approved laboratory for grade of concrete and test certificate shall be produced by the contractor before incorporation in the work.

M&L for 20 mmthick screed bed in cement mortar 1:6 for laying interlocking paver blocks complete all as specified and directed

S&F pre-cast kerb stone of size 300x450x100mm with PCC 1:2:4, type B1 (using 20mm graded crushed stone aggregate) including chamfered, rounded etc. complete all as specified and directed.

Surface dressing not exc 15cm deep including removal/cutting of grass, shurbs etc and removal of debries from the sites to a distance n.exc 50 mtr complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks straight or curved on plan exc 6 M mean radius built in cement mortar 1:4 complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thick (below or above ground level complete all as directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on external surface fair/other than fair faces of brick wall finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for preparation of new concrete/brick/stone or plastered surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of primer etc complete all as specified and directed.

Horizontal boring of holes under road by trenches less technology using ultra sound technology with machine for laying 150 mm bore HDPE pipe without disturbing the road surface complete all specified and directed. Notes :- (i) Boring shall be done upto 1.20 metre below the top surface of road / pavement / hard standing etc. (ii) Quoted rate deemed to be inclusive of cost of HDPE Pipe 150/160 mm bore suitable for 0.4 mpa working pressure.

S&F mild steel for framed mild steel work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all specified and directed.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cment including forms, moulds, mitred stopped ends complete all as specified and directed.

M&L for add or deduct from Sl Item No.51 above for each 25mm girth or part thereof over or under 30cm girth complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in benching, kerbs etc chamfered edges etc including necessary formwork complete all as specified and directed.

M&L for precast cement concrete (1:2:4) type-B-1 (using 20mm graded stone aggregate) set in cement mortar 1:4 in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc complete all as specified and directed.

Cutting into existing manholes, brick wall (ground/first floor) for connecting new drain pipe/bend/Tee of 150 mm dia RCC pipr and making good to pipe or wall leak proof and rendering cutting out existing benching for and forming branch channels (½ round or ¾ section) manholes and filling cut of walls by cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate smooth finish and reforming benching as required for following internal dia of pipe complete all as specified and directed by Engineer-in-Charge.

Supplying, laying and testing of 150 mm dia reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge.

M&L for concrete bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate including necessary shuttering and supports to concrete and for laying bends complete all as specified and directed by Engineer-in-Charge.

Excavation in post holes (or similar holes) each n.exc .05 Cum getting out returning, filling and ramming earth or broken rubble mixed with earth around in layers not exceecing 25 cm, watering and removing surpolus soil to a distance n.exc 50m and making good surface complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-2 (Using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for bright satin polished finish stainless steel tubes, square/ rectangular tube, flat (Grade 304) for structure i.e. post beam and purlin including necessary welding bolting etc complete all as specified and directed.

M&L for multi-layer blue / green colour polycarbonate sheet of 10mm thick jointed by 3mm thick Aluminium strips, fixed over stainless steel frames with stainless steel screws complete all as specified and directed.

S&F 3mm thick aluminium composite panel cladding using aluminium composite panel sheet 3mm thick (Vita 25mm aluminium foil with PVDF coating) at a height of 4-5 mtr (Aluminium composite panel shall be fixed over stainless streel framed works) and filling the gap with silicon, sealant and other materials of approved quality etc complete in all as specified and directed.

S&F perforated stainless steel benches of SS 304 grade of bright satin polish of seating capacity of 04 persons, size 1750x450x450mm with 2 legs fixed with screws and grouted in PCC 1:2:4, type B1 complete all as specified and directed.

M&L brick work with sub class 'B' bricks for half brick wall straight or curved on plan exc 6M mean radius, built in cement mortar 1:4 complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4, Type B0 (Using 12.5mm graded stone aggregate) as in leveling course etc complete all as specified and directed.

M&L for non-skid ceramic tiles 300mmx300mmx 7 to 8 mm thick(square/ rectagular) as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade tile including 15mm thick screed bed layer in CM 1:6 etc complete all as specified and directed. Note : Tiles shall be of premium quality as approved GE.

M&L for Glazed ceramic tiles in vertical surfaces 350 x250x 7 mm/ 450x 350x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade tile over including 10mm thick backing coat in CM 1:4 complete all as specified and directed. Note : Tiles shall be of premium quality as approved GE.

M&L for 20 to 25 mm thick machine pressed precast concree rubber moulded coloured tiles, heavy duty, antiscratched of size exc 0.09 Sqm but not exc 0.18 Sqm jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed. Note : Designm shape and size shall be as approved by GE.

S&F 300 mm bore Reinforced concrete pipes, class NP3, laid and jointed complete with collars all as specified and as directed.

M&L for concrete bed with PCC 1:3:6, type C2 (Using 40 mm graded stone aggregate) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in complete with collars all as specified and as directed.

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube in opening as per specification & drawing complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails with mild steel frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, and with panelling of plain colour PVC sheet fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

S&F exturuded aluminium butt hinges of size 100mm with galvanised mild steel hinges pin anodised and fixed type B-21 complete all as specified and as directed.

S&F 150mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150mm long extruded aluminium alloy handles, cast type, anodised complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

S&F 3mm thick figured glass, pin head type glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F vitreous china squatting pan of orissa pattern size 580 X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including provision of concrete bedding complete all as specified and directed.

S&F vitreous china wash down water closet pan (one piece type) ivory with PVC sheet cover & flushing cistern, flushing pipe, including making good the floor with adjacent floor finishing and making connection to flush pipe etc complete including making functional and removal rubbish/waste materials to a distance n. exc 50m, complete all as specified and directed. Make of WC : Hindware Cat No 92043 (INOX)/ CERA-COMFY Cat Part No 2075

S&F10 ltrs capacity PVC low level valve less flushing cistern (white) syphonic action type with all fittings such as inlet ball valve, float, and handle 32 mm dia polythene high density flush pipe complete all as specified and directed.

S & F vitreous china wash hand basin, white flat/angle back size 550 x 400 mm including necessary cutting holes and pinning in ends of brackets and 1mtr long and 32 mm bore PVC waste pipe and 32 mm PTMT waste coupling complete all as specified and directed.

S&F vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F 15 mm bore stop valve ISI marked, cast copper alloy, screwed down, high pressure, fancy type handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F Bib taps 15mm dia Fancy type Chromium Plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F pillar tap 15 mm bore, cast copper alloy, with capasten head, chromium plated, screwed down high pressure, with or without lettered 'Hot or cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F Self-closing taps, chromium plated push tap 15mm dia fancy type cast copper alloy, screwed for iron pipe (Minimum weight not less than 350 gms) complete all as specified and directed.

S&F PVC connection 450 mm long with brass coupling on both end suitable for 15 mm bore of pipe all as specified and directed.

S&F chromium plated tubular towel rail 20mm dia D type 60cm long between flanges complete all as specified and directed.

S&F for Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats(Minimum weight 300gms) complete all as specified and directed.

S&F health faucet 15mm diam fancy type hand Jet spray with one meter long easy flex tube in chromium finish and well look complete all as specified and as directed.

S&F toilet paper holder of brass CP, fancy type, fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

S&F 500 litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) two layered ISI emossed hoisted and fixed in position including taking down complete all as specified and directed.

S&F 20mm dia ball valves high pressure of with epxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F 20mm dia gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F 25mm dia gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Supply, laying and testing 15mm bore galvanised steel water tubing medium grade, with all fittings fixed to walls, ceilings, laid in floors complete all as specified and directed.

Supply, laying and testing 20mm bore galvanised steel water tubing medium grade, with all fittings fixed to walls, ceilings, laid in floors complete all as specified and directed.

Supply, laying and testing 25mm bore galvanised steel water tubing medium grade, with all fittings laid in trenches complete all as specified and directed.

S&F for 100mm dia cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed.

S&F 100mm dia cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S&F for 100mm dia cast iron bend (any radius) with duck’s foot or heel rest complete all as specified and directed.

S&F for 100mm dia cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors complete all as specified and directed.

S&F for 100mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete 1:2:4,type B1 complete all as specified and directed.

S&F for 100mm dia cast iron cowls complete all as specified and directed.

S&F PVC waste pipe 32mm dia suitable length for wash basin complete all as specified and directed.

M&L for cutting chases, pinning in making good to facings where required pointing in cement mortar 1:3 to end or edges of landing, steps cills, sunshades, shelves,lintels etc. and cutting chases for concealed watertubing or concealed conduit wiring etc. and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed.

Point wiring using approved colour coding as per IS, with Zero Halogen Flame retardant (HFFR), smoke free, non toxic, non corrosive installation cable with UNILAY construction copper conductor 1.5 Sq. mm (nominal area), single core, insulated and unsheathed stranded cable 1100 Volts grade ISI-694 marked & including heavy duty, electric resistance welded(ERW) stove enameled surface mounted conduit, heavy duty ISI marked as per IS:9557 (Part I) 1980 for light points controlled by one Switch , including HFFR insulated unsheathed unitary construction copper conductor 1.5 Sq. mm nominal cross sectional area wire as earth continuity conductor up to common earth and connecting to earth dolly complete all as specified and directed. Note :- All conduit accessories such as bends, elbows, Tee etc shall be included in quoted rate.

S & F LED light fitting. flameproof type FLP-WP of 1x20 w including integral reflector made of alluminium alloy LM6 , with led tubes and all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor with suitable size all as specified and directed. Make :PHILIPS/HAVELLS/CROMPTON/BAJAJ as approved by GE

M&L for flame proof Junction box and cover and outlets 100x65 mm complete all as specified and directed.

S & F in flame proof rotary type with termination box in LM6, 16 Amp, single pole 250V complete all as specified and directed.

S& F of flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth complete all as specified and directed.

S&F flame proof exhaust fan 220 volt 50 Htz 380 mm sweep, 1400 RPM complete all as specified and directed.

S&F flame proof distribution board 4 way single phase complete all as specified and directed.

S&F flame proof MCB single pole 6 to 32 Amp 10 KA 220 volt 50 Htz complete all as specified and directed.

S&F flame proof MCB single pole & Neutral 40 Amp 10 KA 220 volt 50 Htz complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron wire 4mm dia as earth lead wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No. 3, MES SSR Part I- 2009 with 15 mm dia medium grade GI pipe as a protection to earthing lead and 20 mm dia medium grade GI pipe for watering purpose including excavation & earth work in any type of soil, funnel, wire mesh, RCC pit with cover, cast iron frame complete and connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed. Notes (i) The concrete pit shall be PCC (1:3:6) type C-1, 40mm thick precast cover slab of RCC with suitable Mild steel handle in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I (ii) PCC pit shall be provide at least 500 mm away from the earth pit and not on just on the eath pit and extra cost of additional length of water pipes and fittings junction etc shall be deemed to be included in the rate. (iii) Item includes the cost of 7.5 metre earth lead wire and GI pipe for protection of earth wire. Any varriation in quantity shall be adjusted.

Supply, laying, jointing & testing of underground LT cables XLPE insulated, PVC sheathed, aluminium conductors, multistranded, armoured heavy duty 1100 Volt grade cross sectional area 2 core 16 Sqmm laid in trenches/ducts/along poles/through pipe under road etc with new aluminium lugs including taking out complete all as specified and directed. Note :- (i) Excavation, earth work, sand cushioning, protection covers and pipe shall be measured and paid for separately under respective items of this schedule.

Supply and laying sub class 'B' bricks (Old Size) 230x115x75 mm laid flat in trenches as cable covers complete all as specified and directed.

Supply, fix, connecting and testing LED street light 25 watt 6000k new generation energy saving and environmental friendly long life led street light made up of pressure die cast aluminium housing with high efficient led as lighting source and PC cover having top opening seperate driver compartment with IP66 protection and impact resistance of IK07 roadway luminaries with high power LED as light source and electronic driver complete with connection and accessories for fixing with with including grade 40mm dia GI pipe as bracket of appropriate length complete all as specified and directed. Make :PHILIPS/HAVELLS/CROMPTON/BAJAJ as approved by GE

M&L for concealed point wiring PVC insulated and unsheathed cable with 2 runs of 1.5 Sqmm copper conductor single core multistranded 1100 Volt grade confirming to IS 694 drawn through PVC conduit of suitable size concealed metal box suitable for moudular switch and 1.5 Sqmm earth wire copper insulated wire connected to common earth dolly for one light point controlled by one one way switch complete all as specified and directed for one light point/fan/Exhaust fan point controlled by one switch

All as per Sl Item No.123 above but one three pin socket out let 5 amps on independent board complete.

All as per Sl Item No.123 above but one three pin socket outlet on same board

All as per Sl Item No.123 above but with 4 Sq mm copper conductor PVC insulated and unsheathed cable for 3 pin 15 Amps power point on independent Board 4 Sq mm copper conductor PVC unsheathed as earth wire complete all as specified and directed.

S&F Switch piano flush type single pole one way 5A, SP 230 Volts complete all as specified and as directed

S&F ceiling rose surface type 3 terminals 65x20mm complete all as specified and as directed

S&F Socket outlet 2 in 1, 2/3 pin, 5 Amps Flush type complete all as specified and as directed

S&F Modular switch socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed

S&F Modular Switch single pole one way 16A, 230 Volts complete all as specified and as directed

S&F Exhaust fan AC single phase 230 volt of size 300 mm sweep plastic body with louver and making of holes and grouting nuts and bolts and connecting with 3 run of 1.5 sqmm single core PVC insulated multistranded including making hole and making good the disturbed surfaces to match with the existing complete all as specified and as directed

S&F sheet metal enclosure single pole and neutral 4 way double door 240 volt 50 Htz complete all as specified and as directed.

S&F MCB SPN 32 Amps capacity 240V including taking down old unserviceable MCB SPN complete all as specified and as directed

S&F MCB, SP 06 to 32 Amps 240V including taking down old unserviceable MCB SP complete all as specified and as directed

S&F LED fitting of 21 watt integral sleek extruded aluminium housing LED channel with white acrylic cover wall mounted type complete all as specified and directed Make : Philips cat No BN021C LED20S PSU CDL GR /Havells Cat No HEWEBP7IN1W020/Crompton cat No LCCLB20-CDL including the taking down old unserviceable one and depositing the same in MES store yard checking of serviceability by Engineer-in-Charge.

S&F LED fitting of 10 watt integral sleek extruded aluminium LED channel with white acrylic cover wall mounted type complete all as specified and as directed Make : Philips cat No BN021 LED10S-6500 PSU GR S1/Havells Model : LHEWEBP7IN1W01/ Crompton cat No LCCLB08-CDL including the taking down old unserviceable one and depositing the same in MES store yard checking of serviceability by Engineer-in-Charge.

S&F storage type water heater/ Geyser 25 Ltr capacity ISI marked comprising safety valve,indicator lamp, PVC pipe complete all as specified and as directed.

M&L for cutting / boring the existing GI pipe line upto 100 mm dia and taking the connection by inserting Tees of suitable size/threading and make all leak proof connection complete etc all as specified and directed.

Supply and laying in trenches XLPE, PVC insulated galvanised steel strip armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 2 core complete all as specified and as directed.

Supply and spread clean river sand as cable cushioning for proctection of cable to be laid in trenches all as per SSR Part-I complete all as specified and as directed by the Engineer-in-Charge. Note: Punned depth will be measured and paid.

M&L for repalcement of 50 mm bore GI tubing, light grade for passing through cables under the floor, along the wall or along the pole complete all as specified and directed.

Z N Enterprises

bharat construction

M/S SAHARA ENTERPRISES

M/S SATISH KUMAR

M/S Rakesh Singh

Krishna Enterprises

M/S Shivam Industries

A S ENTERPRISES