Item rate tender for civil work.

Amount

Civil work.

Earth work in cutting and cartage up to 8 K.M with all complete (Item No. 251+253(d)+253(e)

Earth work in filling ordinary soil ……… all complete.(As per Analysis)

Sand filling in plinth including ………… all complete. (Item No. 255)

P/L cement concrete in 1:6:12 etc………… all complete. (DSR PWD SI NO. 273)

P/L cement concrete in 1:5:10 etc………… all complete. (DSR PWD SI NO. 274)

P/L cement concrete in 1:2:4 etc………… all complete. (DSR PWD SI NO. 4.1)

P/L cement concrete in 1:1.5:3 etc………… all complete. (DSR PWD SI NO. 4.1)

RCC work P/L in Position specified grade of reinforced cemet concrete in 1:2:4 etc……… all complete. (DSR/PWD SI NO. 5.1)

RCC work P/L in position specifled grade of reinforced cement concrete in raft foundation in 1.1.5.3 etc……. All complete. (DSR/PWD SI NO. 5.1)

M-150 class Brick work on 1:4 cement and fine sand mortor with all complete. (DSR SI.NO. 6.1)

M-150 class Brick work on 1:6 cement and fine sand mortor with all complete. (DSR SI.NO. 6.1)

M-150 class Brick work on 1:3 cement and fine sand mortor with all complete. (DSR SI.NO. 6.8)

2 Cm thick D.P.C with cement and approved coarse sand 1:2 etc……….. All complete. (DSR PWD SI. No. 360)

32 mm thick Supply and fixing of flush doors etc……… all complete. (PWD/DSR SI No. 470)

Providing & Fixing 1.00 mm thick decorative high pressure laminated sheet of plain wood grain in gloss etc……… all complete. (PWD/DSR SI No. 9.127)

Mild steel and iron work of small size etc……… all complete. (PWD/DSR SI No. 502)

Mild steel and iron work of heavy size etc……… all complete. (PWD/DSR SI No. 503)

Providing GI barbed Wire (Hot Dip) iron wire fencing in three rows including fixing it to post after stretching it including labour and tools and plants etc. required for proper completion of the work also including supply of wires (14X14 SWG) with 100mm Barb Spacing (@ 11.66m per Kg Wt) and excluding supply of posts.

Steel wok in built up tubular (round,square or rectangular hollow tubes etc.) truses etc. including cutting. Hoisting fixing in position and applying apriming coat of approved steel primer, includingwelding and bolted with special shaped washers etc.complete. (Hot finised welded type tubes.

Mild steel or iron work in plain work etc……… all complete. (As per analyisis)

Mild Steel Iron 'Z' section windows and ventilators excluding cost of glass panes of but including supply of all materials,its fabrication, nuts and bolts, holdfast, labour and T&P required for proper completion of work as per direction of Engineer-incharge and also including cost of handles,stays etc, in all respect at site of work.

Mild Steel Iron Grill & Staircase railing of a approved qualitiy and drawing including supply of all materials, fabrication, labour, T&P in all respect as per direction of Engineer-in-charge for proper completion of work at site.

Supply and fixiing ward robe shutters made of 18 gauge (1.25 mm) M.S sheets including cold rolling of required shape and including supply & fixing of approved qualitiy locks handle etc. Complete including supply of all material labour and T&P spray painting etc. complete

Providing and fixing stainless steel (Grade 304) etc……… all complete. (PWD/DSR SI No. New)

Providing and fixing stainless steel (Grade 202) etc……… all complete. (PWD/DSR SI No. New)

Providing of 1.00 mm thick with zine coating not less then 275 gm/sqm corrugated G.S sheet roofing including vertical./curved surface fixed with ploymerr coated etc……… all complete. (PWD/DSR SI No. 12.1)

Providing and fixing on wall face unplasticised rigid PVC rain water pipers conforming etc……… all complete. (PWD/DSR SI No. 12.41)

12 mm thick plastering work on 1:3 cement and course sand mortor with all comoplete. (PWD DSR SI No. 13.9)

12 mm thick plastering work on 1:4 cement and course sand mortor with all comoplete. (PWD DSR SI No. 13.4)

12 mm thick plastering work on 1:6 cement and course sand mortor with all comoplete. (PWD DSR SI No. 13.4)

Making grooves 10 to 12 mm wide x 8mm deep in plaster of the wall or in celling vertically or horizontally as required. (PWD DSR SI No. 598 (1).

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters etc………… all complete. With cement mortal 1:4 (1 Cement : 4 fine sand) (PWD DSR SI No. 14.1)

Cement concrete flooring 1:2:4 ( 40 mm thick floor) etc ………. All complete. (PWD DSR SI No. 665)

Supply & Laying tack coat of bitumin @1/4kg per sqm with all complete

Providing and laying DBM 50mm thick compacted with HMP & pavour finisher with all comp.

Providing and laying SDBC 25mm thick compacted with HMP & pavour finisher with all comp.

Providing and fixing 18 mm thick Granite (gang saw cut), 20 mm thick base cement morrtal 1:4 etc……….. All complete. (PWD/ DSR SI No. 11.23)

Providing and laying ceramic glazed floor tiles of size 300x300 mm etc ……… all complete. (PWD/DSR SI No. 11.37)

Providing and laying Vitrified tiles in floor with lean concrete of 500x500 sizes (thickness 10mm) etc …………. All cmomplete. (PWD/DSR SI No. 11.27A)

S/F Chequerred precast cement concrete tiles 22 mm thick in footpath 20 mm thick bed of cement mortar 1:4 including preparation of 50 mm thick base with concrete 1:4:8 40 mm B/B complete. (PWD/DSR SI No. 11.2)

Applying Priming coat over steel and other metal surface up to 10 cm etc ……. All complete. (PWD/DSR SI No. New 641)

Applying Priming coat new wood surface up to 10 cm etc ……. All complete. (PWD/DSR SI No. 19.61)

Painting 1st coat over priming coat on steel and otherr metal surface up to 10 cm etc …………. All complete (PWD/DSR SI No. 19.29)

Painting 1st coat over priming coat on new wood surface up to 10 cm etc …………. All complete (PWD/DSR SI No. 19.29)

Distempering (first coat) with oil bound distemeper of approved brand etc …………. All complete (PWD/DSR SI No. 649)

Removing oil paint or varnish from steel and other metal surface of from wood based surface etc …………. All complete (PWD/DSR SI No. 657)

Finishing walls with water proofing cement paint of approved mak such as super snowcem durocem, Robiance, Guttucem, Supercem quality and of required etc …………. All complete (PWD/DSR SI No. 660)

Finishing walls with sandlex matt. Coat over a priming coat of water proof cement paint etc …………. All complete (PWD/DSR SI No. New)

Well painting (one coat) with plastic emulsion pain of approved brand etc ……….. All complete. (PWD/DSR SI No. 18.58)

Finishing walls with putty approved brand and etc ……….. All complete. (PWD/DSR SI No. New)

Finishing walls with Textured exterior paint approved brand and etc ……….. All complete. (PWD/DSR SI No. New)

Dismeantling brick work or stone work in lime or cement etc ……….. All complete. (PWD SI No. 692)

Dismeantling reinforced cement of reinforced brick worrk including stacking etc ……….. All complete. (PWD SI No. 694)

Dismeantling cement concrete or brick or granolithic floors includingg etc ……….. All complete. (PWD SI No. 697)

Dismeantling existing plaster including disposal of refuse as directed etc ……….. All complete. (PWD SI No. 706)

Scrapping old white or colour wash including etc ……….. All complete. (PWD SI No. 708)

Dismentaliing of B.O.E soling / Inter locking tiles stacking etc ……….. All complete. (PWD SI No. New)

Red sand stone work for wall lining etc. 30 mm thick in 1:3 etc …….. All complet. (PWD/DSR SI No. 7.23)

Construction of Granular sub-base (GSB) etc………. All complee. (Ase per Analysis)

Brick soling with straight over burnt brick laid flat and dry brick edging on both side including etc………. All complete. SCH PWD No. 762(b)

Supply and laying of I shaped precast 80 mm (Ordinary Grey) Interlocking tiles etc………. All complete. SCH PWD No. New

Supply and laying of I shaped precast 80 mm (Ordinary Coloured) Interlocking tiles etc………. All complete. SCH PWD No. New

Supply and laying of I shaped precast 80 mm (Rubber Molded) Interlocking tiles etc………. All complete. SCH PWD No. New

Consolidation of Stone Ballast in patch Repair by hand rammer including patch rectangular shape Including blinding the entire consolidated surface with local earth as directed by EI/C.

Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectrorising glass beeds @ 250gms per sqm. Area, thiclness of 2.5mm is exclusive of surface applied glass beeds as per IRC:35. The finish surface to be lavel, uniform and free fromstreaks and holes. composition of thermoplastic meterial shall be as per table 800-3 of clause 803 of MORTH including cost of all meterial, labour, T&P etc. require for proper completion of work as direction by engineer-in-charge.

Constructing brick masonry manhole etc………… all complete. Inside size 900x800 mm and 500 mm deep including C.I Cover frame (DSR SI No. 19.7)

Constructing brick masonry chamber for underground C.I inspection chamber and bends etc………… all complete. Inside dimensions 455x610 mm and 45 cm deep for single pipe : with common burnt clay F.P.S (non modular) brick of class designation M- 150 (DSR SI No. 19.30)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs 12.5 mm thick tapered edge gypsum moisture resistant board DSR No. 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing, in position concealed G.I. section for wall panelingusing board of required thickness fixed on the 'W' profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the 'W' profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48mm wide jointing tape to provide seamless finish. 9.133.2.1 8 mm thick cement fibre board as per IS : 14862

Material

supply of M150 class bricks

supply of fine sand .

supply of course sand .

supply of stone grite 20mm gauge .

supply of stone grite 10mm gauge .

supply of ordinary portland cement ( J.P, A.C.C, Birla, J.K or equivalent) OPC

supply of ppc cement ( J.P, A.C.C, Birla, J.K or equivalent)

supply of WHITE cement ( J.k,OR Birla brand or equivalent)

Supply of 45-63 mm gauge stone ballast etc………. All complete. (Ase per Analysis)

Supply of 22.4-53 mm gauge stone ballast etc………. All complete. (Ase per Analysis)

Supply of Quary Dust

Supply of 80 mm thick C.C interlocking tiles(Gray) with all complete.(SOR NO. 8)

Supply of 80 mm thick interlocking tiles (coloured rubber moulded) with all complete.(PWD. 4(A)

Supply of 100 mm thick interlocking tiles (Grey) with all complete.(PWD. 4(A)

Supply GSB.(As per anaylisis)

Head load per chainges (30m/CUM)

Supply of red sand stone

Supply of R.C.C Main Hole Cover

Supply of R.C.C Main Hole Ring

Supply of M.S Iron tmt bar 8 mm dia

Supply of M.S Iron tmt bar 10 mm dia

Supply of M.S Iron tmt bar 12 mm dia

Supply of R.C.C 900x450x100 Mm (PreCast)

Supply of R.C.C 1200x450x100 Mm (PreCast)

Supply of R.C.C 1500x450x100 Mm (PreCast)

Supply of R.C.C 600 mm dia Manhole cover (PreCast)

Supply of ballies (100mm) avrage dia

Supply of plain Glass 5mm thick

Labour

Mistri

Mason (for floor & tites work)

Painter (for Polishing work)

Painter (for Painting work)

Mazdoor

Gardener

Maham Sales

Arth Exports

M/S ANJALI ENTERPRISES

SHRI RADHEYSHYAM ENTERPRISES

SEEMA DEVI

AP INFRA SOLUTIONS

Vijay Singh

M/S MAHAVEER TRADERS

Gaurav Gola Contractor

Neeraj Kumar Contractor

ANYA ENTERPRISES

Mahesh Chandra Agrawal Thekedar

Vaikunthi Devi Contractor

M/S R R CONTRACTORS

Dheeraj Kumar Contractor

N P TRADERS

S M V D INFRATECH

ARUSH ENTERPRISES

GANPATI CONTRACTORS AND SUPPLAYERS

M/s Jaiveer Singh

M/S SHRI MARUTI SALES

Subhash Chand Rathore Thekedar

Abhishek Contractor

AMAN MISHRA TRADERS

GOOD LUCK CONSTRUCTION

Manoj Kumar Contractor

A. S. Traders

KAPIL MOHAN MAHESHWARI

JAI SAI CONSTRUCTION COMPANY

Bajrang Traders

Sunita Devi Contractor

M/S SAANGVI CONSTRUCTION & SUPPLIER

SHIV DURGA CONSTRUCTION AND SUPPLIERS

M/S R. B. ENTERPRISES

SWASTIK DEVELOPERS AND CO

RAM KISHOR RATHOR

M/s S.R. Construction

M/S HEMLATA

Hari Chand

D.K. BUILDERS

ANSHIKA CONSTRUCTION

M/s Bhole Contractor

M/s MAA PEETAMBRA CONTRACTOR AND SUPPLIERS

SHARDA CONSTRUCTION

M/S VIJAY KUMAR

M/s DIA INFO & SERVICES

M/S A.G. CONSTRUCTION

SHREE KRISHNA COSTRUCTION

M/S SAMMAN SINGH

M/s GARG ENTERPRISES

M/s Gyan Devi Contractor and Suppliers

Mayank Construction AND Suppliers

M/s GYATRI ENTERPRISES

ASTHA CONSTRUCTION AND SUPPLIERS

ADITYA CONTRACTOR

KHATU SHYAM ENTERPRISES

M/s, Sri Madhav Ji Constaction

JAI AMBEY TRADERS

M/S HIMANYA CONSTRUCTION

SHREE RADHE KRISHNA ENTERPRISES

M/S PSR INFRATECH

M/S RAM VIR SINGH

SANIDEV CONTRACTOR AND SUPPLIERS

M/S SHISHANT AGARWAL

S. R. CONTRACTOR & SUPPLIER