Karnataka

Financial Eval

Works

Water supply/sewage lines

Construction of OHT borewell motor and pipleine at Sulepeth village in Chincholi Taluka

Rural Drinking Water and Sanitation Department

RWSSD Division Office Kalaburgi | Kalaburagi, Karnataka

Amount: ₹29.2 LCloses: 4 May 2026Closed

Timeline

Published27 Apr 2026
Closed4 May 2026
Financial Evaluation—
Award—

Bids

1 Bid4 May 2026

#	Company	Amount	Status
1	Santosh Kumar ₹24.7 Laccepted-finance	₹24.7 L	accepted-finance

Tender Value

₹29.2 L

EMD Value

₹58,425

Closing Date

4 May 2026, 9:30 pmClosed

Tender Inviting Authority

Office Inviting Bids

Rural Drinking Water and Sanitation Department

Contact Person

Sana Afreen

Mobile Number

Work Description

Construction of OHT borewell motor and pipleine at Sulepeth village in Chincholi Taluka

Tender Information

Tender ID

RWSSD/2026-27/WS/WORK_INDENT10046

Reference Number

RWSSD/2026-27/WS/WORK_INDENT10046

Tender Type

Open

Product Category

Water supply/sewage lines

Form of Contract

Electronic Documents, First(One Cover)

Location

RWSSD Division Office Kalaburgi

Source Website

Subscribe to view

Documents Required

4 documents required · 4 mandatory

Technical Bid

RequiredThe Tenderer shall have valid class - III KPWD

RequiredAs prime contractor at least one similar work such as of value not less than 50 percentage of amount put tender last 5 financial years 2020-21 to 2024-25 not below rank of Executive Engineer

RequiredAssessed available tender capacity computed as per the formula in section 3.6

RequiredIn any two financial year out of last 5 financial years 2020-21 to 2024-25 Turn over Certificate Certified by Chartered Accountant with UDIN Number compulsory

Eligibility Criteria

Tenders from Joint ventures are not acceptable.

Bidders shall not be under a declaration of ineligibility for corrupt and fraudulent practices issued by Government of Karnataka

Bidders shall ensure upload of relevant document certifying his/her status as Scheduled Caste/ Scheduled Tribe/other reserved category as prescribed in the tender document.

It shall be the responsibility of the Bidder to ensure credit of Tender Processing Fee and EMD into the respective receiving bank accounts of e-Procurement on or before the last date and time of bid submission.

EMD Payments through e-Payment mode shall be made as one single transaction and payments made in part are liable for rejection.

Minimum financial turnover (civil engineering construction works) not less than two times the annual payments from this contract (Rs. xxxxx Lakhs)

Satisfactoriy completed (atleast 90%) as prime contractor at-least one such similar work of value not less than Rs. xxxxxxx (80% of estimated cost of tender)

Tenderer or his identified Sub Contractor should possess valid Electrical License for executing building electrificatio works and should have executed similar electrical works totallng Rs. xxxxxx (not less than 50% of electrical works) n any one year

Tenderer or his identified Sub Contractor should possess valid license for executing water supply / sanitary engineering works and should have executed similar works totallng Rs. xxxxxx (not less than 50% of electrical works) n any one year

Total value of civl engineering works executed and payments received in the last five years (year-wise)

List of existing commitments and ongoing works

List of works for which tenders already submitted

Banker Details for reference

Construction equipment owned by the tenderer and equipment proposed to be deployed on this contract, if awarded

Reports on the financial standing of the tenderer, such as profit and loss statements and auditor’s reports for the last five years

Qualification and experience of the key technical and management personnel in permanent employment with the tenderer and those that are proposed to be deployed on this contract, if awarded

Proposals for subcontracting components of works amounting to more than 20% of the contract price (for each, the qualifications and experience of the identified sub-contractor in the relevant fields should be attached)

The Employer reserves the rights to reject any of all tenders without assigning any reason

The Department is not responsible for any delay in accessing KPPP portal

Corrigendums / modifications / correction if any will be published in the website only

If any date in the tender time table is government holidays, nest working date will be considered

Bidders are bond the guidelines / instructions issued time to from the government

The tendered at his own responsibility and risk is required to visit and examine the site of works and its surroundings and obtain all information that may be necessary for preparing the tender and entering into a contract for construction of the works. The cost of visiting the site shall be at the tenderer own expense

Fee & Financial Details

Tender Fee Amount

₹740

EMD Fee Amount

₹58,425

Important Dates

Last Activity

4 May 2026

Published

27 Apr 2026

Download Ends

4 May 2026

BOQ Preview

•

Construction of OHT borewell motor and pipleine at Sulepeth village in Chincholi Taluka

•

Supplying, Laying and Jointing Cast Iron (CI) double flanged pipes true to line / hoisting of DI flanged pipe in position and aligning to correct plumb, including cost of jointing materials, conveying...

•

Providing and fixing DI/CI puddle flanges conforming to IS 7181-1986 with latest ammendments., in position for RCC walls including hoisting and conveying them to work spot with all lead and lifts etc...

•

Providing Duck foot bend confirming to IS 1538 (Part-I to XXII) 1978 with latest amendments if any cost of all materials, labour charges etc. complete. 150mm dia (outlet)

•

Providing Duck foot bend confirming to IS 1538 (Part-I to XXII) 1978 with latest amendments if any cost of all materials, labour charges etc. complete. 100mm dia (Inlet,over flow ,scour,and bypass)

•

Providing 80 mm dia Bell mouthed pipes (flanged) confirming to IS 1538 (Part-I to XXII) 1978 with latest amendments if any cost of all materials, labour charges etc. complete. 100mm dia (Inlet,over f...

•

Providing 80 mm dia Bell mouthed pipes (flanged) confirming to IS 1538 (Part-I to XXII) 1978 with latest amendments if any cost of all materials, labour charges etc. complete. 150mm dia (outlet)

•

Supplying and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of ductile iron (DI) conforming to IS-1865 and of grade GGG 40/50, shaft of stainless steel, wedge ...

•

Earth work excavation for Foundation In all kinds of soils Depth upto 3 m by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shorin...

•

Earth work excavation for pipelines/cables In all kinds of soils. Depth upto 1.50m by Manual means upto 600 mm trench width, as per drawing and technical specifications, including setting out, shorin...

•

Providing and laying in position plain cement concrete PCC 1:2:4 using 40 mm aggregate for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fi...

•

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating EACH deposited layer by r...

•

Providing and laying in position Reinforced cement RCC M25 Design Mix with 20mm aggregate for footings, rafts and combind footing etc.with smooth finishing the exposed faces in CM 1:4, 12mm thick conc...

•

Providing and laying in position Reinforced cement concrete for columns, braces and ring beam above ground level. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per re...

•

Providing and laying in position Reinforced cement concrete for shell portion, bottom dome / slab and ribs over the staging. The granite/trap/basalt crushed graded coarse aggregates and fine aggregate...

•

Providing and laying in position Reinforced cement concrete for side walls of water tank over the staging above the ground level. The granite/trap/basalt crushed graded coarse aggregates and fine aggr...

•

Providing and laying in position Reinforced cement concrete for top dome of water tank over the staging above the ground level. The granite/trap/basalt crushed graded coarse aggregates and fine aggreg...

•

Providing Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening,cutting, bending, placing in position, binding and anchoring to adjacent...

•

Providing and fixing RCC final and ventilators as per approved design and specifications with form works and protected with wire mesh. The plinth to be of RCC circular pillars and canopy with an ornam...

•

Providing and fixing MS inspection door of size 60 cms x 60 cms, including MS frame made of 50x50x6mm angle, shutters made of 3mm thick MS sheets, with hinges, locking arrangements at top etc. includi...

•

Providing and fixing gauge with iron sheet or enamelled guage plate of 3mm to 4mm thick, 0.23 M width with copper floats indicators and flexible nylone wires, painting figures with approved enamel pai...

•

Providing two coats of water proof cement painting with approved colour and shade over one coat of primer including scrapping the surface with wire brushes etc. before removal of scaffolding for new R...

•

Supplying and fixing lightening arrestor with aluminium strip 25mm x 3mm size including finial and grounding, aluminium strip to be embeded in one of the columns in and independent GI conduit of 40mm ...

•

Supplying and fixing 40mm dia. GI pipe medium duty pipes hand railing 3 rows fixed to RCC 1:2:4 vibrated post of 150x150mm at bottom and 100x150mm at top, placed at 2 Mtrs. intervals for a height of 7...

•

Ladder inside the container: Providing anodized aluminium ladder using 65mm x 32mm x 3.0mm ‘C’ section for ladder side channel x 25mm dia., flutal pipe for Rungs at 250mm c/c ladder fixed at an an...

•

Providing and fixing MS ladder between landings, 45 cms wide using angle iron of specified sizes, 20mm MS bars at 25 cms. centre to centre, with necessary supports of same angle iron etc. as directed,...

•

Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade

•

Painting Two Coats on New Concrete Surfaces Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces

•

Valve Chamber Earth work excavation by manual means for drains,canals, waste weir draft, approach channels, key trench, foundation of Bridges and such similar works, as per drawing and technical speci...

•

Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS...

•

Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixe...

•

Supplying, Fitting and Placing un-coated TMT Fe 550 & above bar Reinforcement in Foundation complete as per Drawing and Technical Specifications.

•

Providing and fixing 60x60cms M.S. inspection door with necessary M.S. frame made out of M.S. angle 50x50x6mm and M.S. shutters of 31.5mm or B.G.10 thick with hinges on top and locking arrangement, pa...

•

Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, includin...

•

Supply and delivery at site GM (copper alloy) gate valves confirming to Class-I as per IS 778 with latest amendments, 1 No. screwed in bonnet inside screw, rising spring spindle integral seat screwed ...

•

Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 80mm dia

•

Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 65mm dia

•

Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 50mm dia

•

Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 25mm dia

•

Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for: For 65mm dia GI elbow

•

Supply and delivery at site wrought middle steel (galvanized) GI bend confirming to IS 1239-II, 1991 with latest amendments if any.

•

Supply and delivery at site wrought middle steel (galvanized) GI tee confirming to IS 1239-II, 1991 with latest amendments if any.

Documents

Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.

NIT Documents

kw-2.pdf

Tender Document • 0.64 MB

Ready to Participate?

Download all tender documents and submit your bid

Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .

Loading…

Company

Santosh Kumar

₹24.7 Laccepted-finance