Lake Front Development at Mudichur

Amount

Earthwork excavation and depositing on banks with intial lead of 10 m, and intial lift of 2m, in hard stiff black, cotton soil, hard red earth, shales, Muram, gravel, stony earth and earth mixed with small size boulders etc, as per SS 20B, excluding hard rock required for blasting inclusive of shoring shuttering, bailling out of water where ever necessary and including refilling consolidation etc, complete in all respects complying with relevant standrad specification and as directed by Engineer in-charge

Providing and laying plain cement concrete 1:3:6 using coarse graded aggregate of 40 mm and down size for levelling course under footings, steps, walls, platform etc. including form work wherever necessary and well compacted with necessary holes in pcc etc. all complete, as directed.

Providing and laying Cement Concrete 1:5:10 (One cement, Five crushed stone sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

Plain cement concrete 1:4:8 (one cement, four sand and eight aggregation) using 40mm size HBG stone jelly including dewatering if found necessary and laid in layers of not more than 15 cm thick etc., complete.

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 600mm x450mm x 100mm in Cement Concrete 1:2:4 (One cement, Two crushed stone sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed

Providing guildeline road marking kerb painting (special acrylic medium pigmented ) involving cleaning the surface free of dirt and loose particles applying one coat of primer and applying one layer of 20 to 25 microns. Rate shall include for all materials & labour components etc., as complete all respects complying with relevant IRC specifications, as directed by the Engineer-in-charge.

Providing and painting parking/ road marking strips 100 mm wide on conrete road/ parking surfaces in straight or curved lines as per drawing with two coats of water based road marking paint from Asian or equivalent make and of approved shade, cleaning etc complete, including cleaning the surface before painting with wire brush and making it dust / oil /grese free,washing and drying thoroughly.

Providing and laying of hot applied Thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc., complete as per MoRT&H specification No.803

Providing and fixing on flooring Wood Plastic Composite Decking (146x21), with alumimium joist 50x25 and clips. (Chocolate color) including Fitting charges of WPC Decking all necessary arrangements including transportation etc complete as per vendor specifications.

Preparation of Mounds of various size and shape by availlable excavated/ Supplied earth in layers not exceeding 20 cm in depth, breaking clods, wateringof each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer - in - charge.

Providing and Laying Granular sub base (GSB) by provided coarse graded material confirming to ( table 400-1) mixing in a mechanical mix plant at OMC carriage of mixed material to work site spreading in uniform layers with motor grader on prepared surface and compacted with vibratory power roller to achieve the desired dry density to the required grade and cross slope as per drawings all others incidental charges etc.complete as per clause of 401 Morth Specification using Grade V metals for Bottom layer etc complete.

Providing and making Gabion structure with Mechanically woven Double Twisted Hexagonal Shaped Wire Mesh Gabion Boxes as per IS 16014:2012, Morth Clause 2500, of required size, Mesh Type 10X12 (D=100 mm with tolerance of +_2% ) zinc coated, Mesh wire diameter 3.0 mm, mechanicaaly edge/ selvedge with partitions as every 1m inteval and shall have minimum 10 numbers of openings per meter of mesh perpendicular to twist tying with lacing wire of diameter 2.2 mm, supplied @ 3% by weight of Gabion boxes, filled with boulders with least dimension of 200 mm, as per drawing, all complete as per direction of Engineer-in-Charge

Providing and laying, spreading and compacting graded stone aggregates to Wet Mix Macadam 250 mm thick specification including premixing the materials with water at OMC in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery,fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5 (This Rate Is Applicable Only If Work Is Done During Night)

Supplying and filling in foundation, basement, floor etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Brick partition walls of 11.50cm thickness using best quality Fly ash bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Plastering of 12 mm thick for Internal walls with cement mortar 1:4 (1 of cement : 4 of fine P.sand) according to specifications. Rate shall include for providing GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of 100 to 125mm including tying in position with suitable clamps/screws. .Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Paving the floor with best approved quality fine polished Granite Stone coping with 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Providing and laying Stabilized Mud paving over the aggregate layer sub base provided , Soil and cement (3 to 10% as per soil type) to be mixed wth light Spray of water and spead to a compacted thickness of 10cm ,levelling and hand tamping to achieve Consolidation and curing by spraying of water.

36 mm EPDM flooring (30 mm SBR + 6 mm EPDM) : Providing and laying approved 30 mm insitu SBR rubberized flooring plus 6 mm EPDM flooring laid over concrete which can resist UV radiation and withstand severe weather conditions and approved colour complete for safety of kids in play areas. Including cost of PU Binder/Glue etc as required for the works.

Supplying and Fixing of Pebble/gravel stone in walking track with 30 mm thick Cement mortor 1:3 ratio base layer and fixing the sone with cement slurry over the base mortor surface as per the pattern drawing given by the department officers the rate including cost of gravel stone cement mortor, labour charges transportation loading & unloading, curing, etc.,completed as per the standardspecification and as directed by the departmentoffice

Supplying and laying of Interlocking Paver Block Stone 60mm thk. Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc.,

Paving the floor with Granite flag Stone of 50mm thk varieties size over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc.,

Supplying and laying of Rubber moulded Interlocking Paver Block Stone 80mm the. Over a base layer of crushed stone sand filling incl. Cost of materials laying and Labour charges etc.,

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Supplying and erecting steel shuttering , including necessary supports for plane surfaces in foundation and basement for reinforced cement concrete works such as column footings, Plinth beam, Grade beam, Staircase steps , Bed blocks etc., which requires only nominal strutting using stiffened with mild steel sheets angles of size 25mm X 25mm X 3mm for boarding laid over silver oak joist of size 10cm X 6.50cm spaced at about 60cm centre to centre and supported by the casorina props of 10cm to 13cm dia placed at 75cm c/c or at suitable intervals etc ., complete complying with standard specification. The payment for centring shall be made only after the concrete laid. The retrieved materials should be taken back by the contractor.

Raft & Padestral

Plinth Beam &Column, wall

Slab,Lintel

Supply and fixing in position of Hot rolled structural steel Members/ Sections consisting of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, etc. at all levels. Surface preparation of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive, PU paint (metallic finish) with compatible primer to a minimum film thickness of 75 microns and 2 coats of PU paint of and total dry film thickness 225 microns Rate to including all Lifts, wastage, cost of bolts, nuts, washers, welding,flashing, electrodes and connections required for the work. No extra on this account will be paid for, and the rate to include preparation of fabrication shop drawings for owner's approval. etc., as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge

Design, fabrication, testing, supply, installation of Float Jetty with HDPE Floating Pantoons material and necessary HDPE Connecting Pin, HDPE nut bolts & washer, anchor & SS Handrail in 316 Grade as per the drawing. The rate inclusive of all accessories for float jetty installation, transportation and manpower etc. The floating materials must be certified by IIT/Anna University including 2 years of Warranty complete in all respect as directed by Engineer-in-Charge.

Brick work in cement mortar 1:5(one cement and four sand) using fly ash bricks of size 230mmx110mmx70mm for foundation and super structure as per detailed specifications and as directed by the departmental officers

Brick work in cement mortar 1:6 (one cement and four sand) using Wire Cut bricks of size 230mmx110mmx70mm for foundation and super structure as per detailed specifications and as directed by the departmental officers

Boring through the 450mm dia liner tube in all type of soil strata including sea silt or clay sand and weathered rock. The rate should include the removal of bored material, cleaning the loose particles, bailing chiseling and taking all measures to retain the sides and prevent necking of line from bed level excluding installing of lines & driving of liners etc., complete complying with standard specification and as directed by the departmental officers.

Supply & laying if Grouting as per drawing.

Providing & fixing of Anchor bolt

Providing and fixing Bamboo jaffery/ fencing consisting of superior quality 25 mm dia (Average) alf cut bamboo placed vertically and fixed together with three numbers horizontal running members of hollock wood in scantling of section 50X25 mm, fixed with nails and G.I wire on existing support complete as per drawing.

Dismantling of the existing median along ORR as per site.

Supply and installation of surprise fountain, rain shower, FRP mushroom umbrella complete with 900mm dia sand fileter with a filteration rate of 30000L/hr with the necessary filter media such as silica sandm gravel complete as the specification and approval of the enginner in charge. The system shalla lso be fitted with recirculation pump Horse power : 3 HP, 2.2 Kw, Phase : 1 phase 440v, Flowrate = 30m³/hr @ 14 mtr water head. With underwater lighting complete with all the cabling and transformer. The lighting system shall comprise of 25mm dia heavy duty PVC conduits and prexible 1.5sqmm 2 core cable and 2.5 sqmm 2 core armoured cable. The system shall also be complete with controla and regulatory valves with PN10 rating adn EPDM seat comprising of 32mm dia,90mm dia butterfly valve and 63mm dia ball valve. The system shall also be supplied with PVC pipes of 32mm dia, 63mm dai, 90mm dia and 110mm dia all of approved make and sutiable strength complete with support fittings, tees, bends. The system shall also be equipped with the necessary control panel.The suprise fountain fitting shall be complete with a centrifugal self priming pump, cluster nozzle, control panel,inlet spout and drain cover. The rain shower is made up of GI pipes coated with PU paint and the frp mushroom umbrella is 7ft in height, 6ft in dia,6-8mm thickness with GI pipes with PU paint. The recirculating pumps for these components have the following specs Horse power : 3.00 HP(2.2kW) - Commercial Pump - 90mm Connections Flow rate = 48m³/hr @ 8m water head.Horse power : 5.50 HP(4.0kW) - Commercial Pump - 90mm Connections Flow rate = 70m³/hr @ 8 water head. The entire area to be waterproffed with fibermesh b18 and a final coat of neo 200 with a ration of 1:1 (1 lit ne0 200:1 ltr water). The area shall be finished with glass mosaic tiles with adhesive, grouting complete with labour and transport charges.The foundation work is inclusive of all civil, mep, installation and supply charges.

Supplying and laying of high modulus polypropylene bi-axial extruded geoCELL confirming to Section 700 of MoRT&Hs 5th Revision specifications for base/sub-base reinforcement in pavements having minimum LCR/MIF value of 1.2 for subgrade CBR≤3% %, minimum ultimate tensile strength of 15 kN/m in both cross machine and machine direction, with minimum 5kN/m & 7kN/m tensile strength at 2% and 5% strain respectively in both machine and cross-machine direction, junction efficiency not less than 90% of rib ultimate tensile strength and with 38mm X 38mm mesh opening.

Removing of existing Light Jungle as per site

Scrapping & removing of exiting floor of depth 100mm as per site. The rate is inclusive of labour, transportation, loading & unloading etc complete as per standards

Flooring with chequrred terrazzo tiles of 20 mm thick (medium shade) set over base coat of cement mortar (1:6) 12 mm thick over CC bed already laid or RCC roof slab, including near cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed with neat cement to full depth mixed with pigment of matching shade including cost of all materials like cement, sand water and tiles etc., complete for finished item of work, but excluding the cost of conveyance of all materials.

Providing & fixing of GeoTex tile as per standard specification.

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete cover blocks to maintain the cover as required. The rate including cost of all materials, bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks and GI binding wires etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Plastering 20 mm thick for external surfaces with cement mortar 1:4 ratio (1 of cement : 4 of fine P.sand) including water proofing compound of “CICO No.1 or equivalent“ as per Manufacturer's Specification with sponge finish (washed sand finish) all complete as per specification and as directed.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds, grooves to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supplying and painting of 2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete.Rate including all brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Flooring with following Anti -skid ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Solid PVC Door Shutter using 19 Guage 19mm MS Square tubes for style and outer frames. 15mm MS Square tubes for top ,lock and bottom rails . The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC sheets for Panelling shall rigidly fixed in position Including necessary furniture and fittings. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mmx45mm with suitable rabate for housing the shutter.

Supplying and fixing UPVC Louvered Ventilators of from the profile the size of outer frame 60mm x58mm and shutter profile size of 60mm x 78mm both profile are reinforcement with GI/1mm 125GSM and 100% Corrosion free,the profiles are multi Chambered sections with wall thick of 2mm.The EPDM rubber covered with over all the edges of frame and shutter . The Corners and joint should be welded and cleaned.Radiations free pin headed plain or brown colour glass 4mm thk should be provided in the Louvers.The window should be fixed tothe wall with 100% packing with screws and silicon packing all round the frames. The Ventilator should be got approved from the Executive Engineer before useon work.

Supplying and fixing colour Aluminium sheet roof of .5mm thick with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Pre-Painted Galvanized Iron Two Track Sliding Window: Providing and fixing pre-painted two track, two panel sliding system fabricated from roll formed sections made of galvanized steel powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm. Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted witha polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. imensions of sections: Section for frame two track should be of 59mm x 44mm, section for shutter should be of 35mm x 49mm for window, section for euro groove should be 25mm x 24mm and for lap strip should be 30mm x 41mm. Fixing details: The frame and shutter sections should be cut to length, joined with corner brackets made of glass filled nylon. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass. Accessories: Corner brackets made of glass filled nylon gasket made of Ethyl Propylene Diamine Monomer (EPDM). Locking system should be of single pin locking for Windows. Single wheel rollers for windows should be provided. Glass: Glass shutter and fixed glass portion should be provided with a glass of 4mm pinhead glass. Window frame should be fixed to brick / concrete masonry by using nylon self-expanding caps and driving MS electro plated 80mm long screws into the caps through frames.

Providing & fixing of GI Prefabricated Bunkhouse Toilet with 10000lit Bio septic tank as per drawing. The rate rate is inclusive of the transportation , Installation ect complete as per standards.

Protective Water proofing Providing protective over the water proofing treatment provided over base concrete,RCC retaining wall, sunken slab and terrace in CM 1:4 to a minimum thickness of 12mm with necessary water proofing proofing compound as per standards.

Providing & fixing of Manhole Cover 60 x 60cm (Heavy Duty) with Frame including labour charges & transportation etc complete.

Stone Masonary in cement mortar 1:5 (one cement and four sand) using stone for foundation and super structure as per detailed specifications and as directed by the departmental officers

Supply & Fixing of Bamboo (10cm dia and above) over the MS frame as per drawing. The rate is inclusive of labour, material & other necessary accessories etc complete as per standards.

SS Fabricated dustbin 12X 24 inch

Providing & Fixing of Tensile Fabric bench as per drawing

Providing & Fixing of Precast game table details as per drawing.

Supply and fixing in place Picnic table with GI pipe frame duly powder coated with WPC wood planks on the table top and seat. The table to have a minimum dimensions as the following: Dim - 1500 L x 1500 D x 725 H mm Table size – 1500 L x 690 D x 725 H mm Seating Capacity – 6 persons. All the fixing and installation as per vendor specification as per the direction of EIC

Stainless Steel Tacticle Indicator Stud with stem (dots) - stainless steel 304 grade material, dimension 35mm x 25mm x 4.5mm, 8mm dia 12mm length fixing screw, direction design strip brush glossy finish

Stainless Steel Tacticle Indicator Strip - stainless steel 304 grade material, dimension 280mm x 35mm x 4.5mm, 8mm dia 12mm length fixing screw, direction design and diamond design, brush glossy finish

Supply and filling Silica sand (0.2mm to 0.6mm) in children play area as per the spefications and direction of EIC

Specially Abled Climber A-shaped climber type equipment made of SS and Rope Code- DC-002-CL Size: 10 x 6 x 6

Musical Poles Xelophone Unisex play equipment made of iron and plastic Code- DC-008-ME Size: 6 X 2 X 8

Congo Track Sensory Musical Equipment Play drum made of SS and plastic Code- DC-010-CT Size: 7 x 2 x 4

Playground Musical Panel Plastic packing equipment made of MS and plastic Code- Code ; DC-011-ME Size: 4 x 2 x 6

Play Panel for Specially Abled Unisex play panel made of MS and plastic Code- DC-014-PP Size: 4 x 1 x 4

AIR WALKER SINGLE LENGTH : 1050 MM WIDTH : 450 MM HEIGHT : 1200 MM SAFE AREA : 2. 0 MTR X 1.45 MTR MAIN FRAME : 80MM ID FOUNDATION SUPPORT : 32MM ID CONNECTING PIPES : 32MM ID ( PADDLE ) HANDLE : 25MM ID BUSHES : Φ 60MM MADE IN SEAMLESS PIPE BEARING : PERMANENT LUBRICATED BEARING 6205 OF REPUTED BRAND PINS : Φ 25MM MADE IN BRIGHT BAR CIRCLIPS : A 24 BASE PLATE : 250 MM / 10MM THICK FOOTREST : 245 X 113 MM MADE IN MS MATERIAL NUT & BOLTS : GI NUT BOLTS OF SIZE 18* 40MM / 18*50 MM ACCESSORIES : PLASTIC BEARING / CLOSING CAP POWDER COATING : THE POWDER COATING DONE WITH PURE PP OF REPUTED BRAND

Arm Wheel color : powder coated 10 material : gi b class 1 24800 weight : 45kg hand grip : fibre [plastic)

SA Double surf board LENGTH : 900 MM WIDTH : 850 MM HEIGHT : 1350 MM SAFE AREA : 1. 9 MTR X 1.85 MTR CENTER POLE : 100MM ID HOLEPASS PIPE : 80MM ID FOUNDATION SUPPORT : 32MM ID CONNECTING PIPES : 32MM ID ( LEG SUPPORT ) HANDLE : 25MM ID BUSHES : Φ 60MM MADE IN SEAMLESS PIPE BEARING : PERMANENT LUBRICATED BEARING 6205 OF REPUTED BRAND PINS : Φ 25MM MADE IN BRIGHT BAR CIRCLIPS : A 24 BASE PLATE : 250 MM / 10MM THICK ALUMINUM SEATS : 320 X 270MM & 5MM THICK. NUT & BOLTS : GI NUT BOLTS OF SIZE 18* 40MM / 18*50 MM ACCESSORIES : PLASTIC BEARING / CLOSING CAP POWDER COATING : THE POWDER COATING DONE WITH PURE PP OF REPUTED BRAND

Slide AREA : 2. 8 M X 0.6 M. PLATFORM HEIGHT : 0.9 M SLIDE LENGTH : 1.8 M SLIDE THICNKESS : 5 MM LEG SUPPORT : 48 MM ODMS PIPE LADDER & RAILING : 20MM & 25MM ODMS LADDER STEPS : 2 “ x 1”RECTANGLE PIPE SQ. PLATFORM :2’ x 2 ‘ size made with ms sheet 18 guage & ms angle 25*25*3 support PAINT & COATING :2 LAYERS OF REPUTED MAKE PAINT OR OVEN BAKED POWDER COATING WHICHEVER IS FEASIBLE

Wheel chair merry go round Outdoor circular swing made of MS with a capacity of 2 children Code- DC-023-MGR Size: 14' dia

Platform Merry go round Outdoor circular swing made of SS and plastic with a capacity of 3 childrenn Size: 6' dia

Wheel chair swing Outdoor wheelchair swing for 1 child made of Iron Code- DC-035-SW Size: 14 x 8 x 10

4 seater see saw Outdoor spring see saw made of HDPE for 2 children 3.0 M X 1.5 M AREA : 3.0 M X 1.5 M HEIGHT : 0.45 METER LEG SUPPORT : 48MM ODMS CENTER ROD : 60MM ODMS HANDLE & RING : 25MM ODMS SEATING ARRANGEMENT : 4 NOS. FRP SEATS OF 3MM THICK MOVEMENT : 2 NOS. GAZAN PIN. PAINT & COATING :2 LAYERS OF REPUTED MAKE PAINT OR OVEN BAKED POWDER COATING WHICHEVER IS FEASIBLE.

SA 2 seater swing AREA : 3.0 M X 1.5 M HEIGHT : 2.4 METER TOP BAR : 60MM/75MM/90MM ODMS LEG SUPPORT : 60MM/75MM/90MM ODMS HORIZONTAL SUPPORT : 32MM ODMS SWING SEATS : 2 NOS FRP SEAT 5MM THICK ACCESSORIES : SWING CLAMP / “S” HOOK / GI CHAIN 8MM PAINT & COATING : 2 LAYERS OF REPUTED MAKE PAINT OR OVEN BAKED POWDER COATING WHICHEVER IS FEASIBLE.

Adventure Climbers Mound bridge AREA : 3.6 M X 0.6 M HEIGHT : 1.8 METER INNER FRAME : 25MM ODMS OUTER FRAME : 32 MM. ODMS PAINT & COATING : 2 LAYERS OF REPUTED MAKE PAINT OR OVEN BAKED POWDER COATING WHICHEVER IS FEASIBLE.

Supply & Installation of signages complete with all the components as per drawing Ms powder coated Touch Screen 43 Inch standee - 43 inch Full HD screen with IR touch - Signage Player - PDU

Supply and Installaion of Mobile Charging Kiosk Cabinet complete as per specifications and approval of the engineer in charge. 1.6 mm thickness CRCA Sheet 7 tank Powder Coated Acrylic logo with Backlit as per quote.

Suppy & Installation of WATER COOLER of approved make Voltas or equivalent with the necessary components complete on site as per the approval of the engineer in charge. The capacity of the cooler is 200 litres with complete SS body, emerson compressor or equivalent with PUF insullation and one year waranty.

Supply and installation of seater with shading complete as per the drawing and as per the approval of the enginner in charge. Minimum height of the shading structure in 3m, width of 1.5m and length of 1.5m. The structure shall be of MS structure - powder coated of approved colour with all the relevant shop drawings to be approved by the enginner in charge before installation. The shading material is comprised of wooden slats complete with wood polish.

Supply and Installation of Pylon signage complete as per the drawings and approval of the engineer in charge. Lettering shall be single sided dimension of the structure Size: 7500 x 1584 MM MS power coated structure comprising of Main poles 'C' Channel, 40 square Frame with wooden ACP Cladding with necessary support and angles & laser cut for Tamil font internally illuminated with LED lights. -Zone 1 will be SS brush finish ACP, on top of it flower outline with painted fixed non light -Border line will be 0.40 acrylic projected and internally led illumination. -civil foundation bolt with base plate (M25 grade foundation size: (B) 2 x (W) 1 x (H) 3 ft.) The components shall also have the following minimum warranty Transformers - 1 year warranty LED Modules - 2 years warranty

Supply and installation of name board sigange with upto 12 letters with each letter size: 3 feet (Height) -Individual Standee letters fixed on the ground with base plate. -GI powder coated or MRF vapor cure 3 inch depth female letters on front facia will be white acrylic and internally LED illumination complete as per the direction of EIC.

WATER SUPPLY WORKS

Supply & Installation of Hume pipe of size 300mm dia as per standard specification.

External Water Supply Arrangements Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

15mm dia pipe

25mm dia pipe

32mm dia pipe

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

50mm dia

160mm dia

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and erecting SINTEX or approved equivalent make HDPE plastic vertical cylindrical 2000 Litre Water Storage Tank.Strickly adhering ISI Standard as per ISI Mark 12701 (Latest revision) including all taxes and freight charges within Corpn.City limit.BD-865

Providing & fixing of 160mm dia PVC AND HDPE PIPES FOR BORE WELLS-Special Blue Pipes for Bore Well-160mm dia asp er drawing

CONSTRUCTION OF INDIA MARK-11 DEEP BORE WELL PUMP USING POWER RIG Construction of platform 1.85m dia including necessary earth work excavation supplying and filling in with'Crushed Stone San (Commercially called M-Sand) providing and laying PCC 1:3:6 using 40mm B.G.Metal, and providing and laying PCC 1:2:4 using 12 to 20mm size B.G.Metal, stock brick work in C.M.1:3 for 23cm thick wall, plasterig in C.M.1:3,15mm thick including making necessary drainage arrangements by providing S.W.Gully trap 15x10cm with silt pit and 100mm dia S.W.Pipe connection to a depth of 90 cm, connected to the SOAK PIT ARRANGEMENT,etc.,complete to standard

Providing & fixing of reinforced cement concrete catchpit at every 10m along the storm water line for easy cleaning etc complete as per drawing.

Providing and laying on site RCC non pressure spun pipe with socket and spigot ends as per IS 458/2003 manufactured with sulphate resistant cement with 12 mm HI -alumina lining provided for rubber ring joints. (NP3 Class - 450mm dia) as per the slope and direction of the engineer in charge.

Supplying, Delivering of 24" FRC manhole cover and frame 600mm dia clear opening -complete one set (extra heavy duty)

LANDSCAPING WORKS

Earth work excavation for foundation in all kinds soils in varying depths (Digging of new trenches for hedge / edge planting, digging and removal of excavated earth from site complete).

Supply & stacking of red earth or manure at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost)

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75mm thickness - including hire charges of roller.

Planting of Cynodon dactylon (Arugampul) Grass including necessary soil preparation, transportation, loading and unloading charges etc., as directed by the site in-charge.

Planting of Alternanthera varigated ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Portulaca ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Syngonium foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site incharge.

Planting of Shade grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Truffing of Korean grass / mexican grass including loading and unloading charges transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-

Planting of Ixora hybrid foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Rangoon foliage creeper variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying of plastic Potted plants Dracena Babydoll size of dia 12 inch including loading and unloading charges, transportation, etc as directed by the site incharge

Planting of Lemon grass Herbal plant variety of height 20-25 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Supplying of plastic Potted plants Poinsettia size of dia 12 inch including loading and unloading charges, transportation, etc as directed by the site in-charge

Supplying and Planting of Golden Bamboo tree sapling of height 300 - 360 cm in polythene bag of size 15x16 inch including loading and charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Supplying and Planting of Plumeria tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Terminalia catappa tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Dypsis lutescens (Areca palm) palm variety of height 180-210 cm in polythene bag of size 16x16 inch including upporting stack of 5 cm dia casurina pole of 10 eet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of apling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Tabebuia rosea tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch inluding supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site incharge

Supplying and Planting of Cordia sebestena tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Livistona rotundifolia palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5cm dia casurina pole of 10' height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Syzygium cumini tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site incharge.

Supplying and Planting of Ficus elastica tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Supplying and Planting of Albizia tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Maintenance of shades grass / carpet grass / G grass by regular watering, weeding, protection, mowing etc for a period of One month

Maintenance of shrubs, other ornamental foliage, foliage planting and Trees planting including watering, weeding, application of fertilizers and pesticides, trimming etc for One month.

Supply & Installation of Aquatic Plants Typha Augustifolia

Supply & Installation of Aquatic Plants Phragmites

Supply & Installation of Aquatic Plants Ipomoea Aquatic

Supply & Installation of Aquatic Plants Polygonum (Knotweed)

Supply & Installation of Aquatic Plants Cyperus Species

Supply & Installation of Aquatic Plants Alternenthra (Gudari)

Supply & Installation of Aquatic Plants Water Lettuce (Pistia Stratiosis)

Supply & Installation of Aquatic Plants Canna Lily

Supply & Installation of Aquatic Plants Colocasia Esculenta (Taro)

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) :

Supplying and stacking of sand (Supply & stacking of sand at site to the departmental guage for premeasurements obtained from natural disintegrated rock which has been deposited by streams or glacial agencies composed of hard silicons material and should be clean,sharp and angular type free of adherent coatings)

Planting of Bougainvilla foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Pennisetum setaceum 'Cupreum' foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of sapl ngs at site,earth work excavation of required size, planting ofsapling, refilling of excavatedearth etc as directed by the site in-charge.

Supply and commission of drip irrigation system complete with all the necessary components on site

Providing & fixing of M25 grade precast concrete of size 300x300x400 as per drawing. The rate is inclusive of labour material, necessary shuttering etc complete as per standard specification.

Providing and fixing of Planter box of specified size 900x450mmx600mm with shrubs in both side of pathway. The rate is inclusive of required excavation, refilling, brick work, Maintenance for 3month ,finishing with plastering on exposed surface,PCC and soil filling with shrub all complete as per direction of Officer-in-charge.

Supply and installation on site including transportation charges coir logs for slope stabilisation. Each log has a minimum dimension of 12 inches diameter, 3m length and weight of 30kg.

ELECTRICAL WORKS

Supply and filling in foundation and basement with M sand / filling sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification.

TNEB METERING BOARD – OUTDOOR TYPE Supply and fixng of TNEB meter board suitable for 3 phase 100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1- 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 5 Nos. 63A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connecti n of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire withearth connection complete (SD-130)

Supply and Laying of 4C x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland suitable for 4C x 16 PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 4 C x 16sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 3 1/2 C x 50 Sq.mm PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 3 1/2 Core x 50Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 3 1/2 C x 35 Sq.mm PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 3 1/2 Core x 35Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

"LED Decorative Post top street light, BIS certified with a grey painted top made high pressure die casted aluminium and UV resistant polycarbonate protector (IK08) permanently sealed with the body to achieve separate IP66 optical & IP65 control gear compartments. Suitable for post top mounting on 60 mm OD diameter pipe. All hardware shall be of stainless steel for longer life. The optics of the luminaire shall be designed for efficient indirect symmetric light distribution providing excellent photometry. Design life shall not be less than 50,000 burning hours @ L70. The light engine shall incorporate mid power LEDs in the Luminaires. Overall luminous efficiency of luminaire shall be 85 Lm/W ± 7% at correlated colour temperature (CCT) of 3000K with tolerance as per ANSI standard ), colour rendering index (CRI)>70.Electrical Class I, rated voltage 240Vac, Power Factor ≥ 0.95, with BIS certified potted driver having internal surge protection of 4/4 kV (in both Common & Differential Modes). Shall be supplied pre-cabled (0.3m) for easy installation. Protection features: Short Circuit and Open Circuit Protection for LED. It should survive input voltage stress of 440V for 8 hours.The Luminaire need to be supplied with 3 mtr 3 core x 1.5 Sqmm PVC Sheathed CU cable.CAT REF: Kesslec Graz LED - WW- IP66- SYM - Indirect lighting "

Supply of 4 Mtr height decorative pole made of mild steel/steel tube complied with IS1161/IS 3601, minimum thickness of 3mm. (chemical and Mechanical test report shall submited)The pole shall have two section, base section having length of 1Mtr with dia of 140mm and top section having length of 2 mtr with dia of 76mm . Pole shall be mounted on square base plate of dimensions 200*200*12mm thickness with 4 nos of slots, having distance of 141mmx141mm and size of 20x35mm. The base section of Pole shall have an in-built junction box to accommodate a heavy duty connector for loop‐in and loop‐out of UG cable and provision for MCB with anti‐theft lock arrangement. The Pole Shaft should be fabricated out of Steel tube of grade YST 240. Structurally designed base plate of Steel A36/A572-50 or equivalent should be welded with the pole shaft. The complete structure shall be hot dip galvanized through 7 stage process and single dip process as per ASTM A123 and minimum average coating shall not be less than 65 microns(Test report shall be submitted) before traeting with primer. After galvanisation structure shall be treated with two coats of high quality primer and thereafter coated with Polyurethane paint to minimum average DFT of 100 microns(Test report shall be submitted). The pole shall be designed as per EN40 for withstand basic wind speed of 169kmph. The complete structure should be hot dip galvanised Kesslec Ecopole 4 mtr GI PU Painted with Base plate.

SITC of 6A DP MCB c curve and connector for light fixture wiring in the street light pole.

LED Bollard, BIS certified made of zinc plated cylindrical steel pipe, permanently sealed optical block (IP66) with aluminium heat sink and a diffused PMMA protector (IK07). Highly efficient symmetric light distribution providing excellent photometry to maximise the spacing between the bollards. Suitable for on-ground mounting on 4xM10 bolts on 190mm PCD. system power of 16W, Correlated colour temperature (CCT) of 4000K (optional 3000K & 5700K), colour rendering index (CRI) >70 and L70 rated lifetime of 50,000 hours. Electrical Class I, rated voltage 240Vac, Power Factor ≥ 0.95, with BIS certified potted driver having internal surge protection of 4/4 kV (in both Common & Differential Modes).Kesslec ISA Bollard 16 W LED WW

SITC of ISA LED Bollard with Cable connector necessary Anchor Fatser of M10 x 150 mm with neccesarry nuts and bolts by drilling on the board walks

SITC of 24 v LED Neon strip with 7to 9 W LED IP67 with Aluminium channel , pins, connectors & Accessories Cable connector

SITC of LED Drivers of LED Drivers of 100 W - 220 V -IP67 24 V

SITC of IP Rated Box for fixing of the Drivers

Fixing of Neon LED strip with Nescceasry Nuts and bolts and fixing solution ,etc with Driver along with the IP Box

Supply,installation and commissioning of 1200mm 20W 6500 k, 4feet LED Tube Fitting with TW round blocks on wall or ceiling with PVC nsheathed copper leads from terminals to the fitting and etc to complete the work

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End.

First Aid Box complete with all First Aid Medicines

Danger Board as required by the Electrical Authorities

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the Deparmental Officers. Make: EXCELLENT /SAFETY FIRST / EQUIVALENT (SOR -2023-2024 ,pg 102, M-0852)

EARTHING SYSTEM Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of die not less than 50mm and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environment friendly backfill compound and suitable clamp and with copper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry SD-233

Supply and installation maintenance free GI Earthing System comprising of 50mm die and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp. Rate as per PWD 2023-24 SOR- Schedule No. M-2144 Pg No163

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth. ( SD 78)

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with termination in the earth pits, Panels, Distribution boards and equipments with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

Supply and run of 25mm x 6mm GI flat with necessary clamps / supports on wall / floor / ground for earth connection (SD-77)

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD -458)

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel made up of 2mm powder coated MCCB Indoor Type Three Phase Changer Over panel of size (H 1450 X L 1400 X D 400 ) mm with suitable to accommodate 200A 4 pole Three phase Change Over Switch-1No. as incomer for EB Source and as incomer for DG Source , 1no 160A 4Pole MCCB, 6nos of 125A 4Pole MCCB, and 2nos of 63A 4Pole MCCB's, compartment for as O/G supply with the provisions to accommodate Busbar chamber and cable chamber with size of 33x6mm copper busbar 4 runs having three phase Multifunction meter with line indicators and with all necessary accessories with all other connected works etc. The panel made up of 16/18 SWG CRCA sheet steel comprising of 4 sections with separate sheet steel weatherproof and shock proof safety insulation system conforming to IE Rules with IP protection, and with the panel should be painting by powder coating finishing etc.,as complete and making good of the panel with neat finishing. (Switch make : L & T / ABB) panel should be earthing confirming ISI specifications. The panel should be erected on Anchor fastners, bolts and nuts for mounting the Indoor Panel as directed by engineer-in charge/department superior engineers. Including Bus bar support, Cost of Weldding charges for mounting the panel, Rotary Handle, Spreader Terminal, Multifunction Meter digital type / MFM 5010 LED meter CI 0.5S

VERTICAL THREE PHASE MCB DISTRIBUTION BOARD WITH MCB : Supply and fixing of 84way vertical TPMCB sheet steel Industrial Type TPMCB DB with IP54 Protection of surface type fitted with bus bars and neutral links with1 No. of 100A FP MCB as Incoming and 12 Nos.of 32A,10KA Triple Pole MCB in Flush with wall and making good of the concealed portion with earth connection.( Industrial Type TPMCB DB with IP54 Protections)

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating one no. 4 pole incoming 63 A TPN MCB, 10kA, / Isolator and another separate 4 way for accommodating one no. 63 Amps, 30 mA, 4 pole ELCB / RCD (totally 8 ways in one segment) and 24 nos 6-32 A, 10kA, SP MCB / Isolators ( totally 24 nos.) for outgoing in 3 segments with label holder and provision for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. (SD 716)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 25A FP ELCB switch as incoming and 4 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 2.5 metre down rod with fan clamp, and wiring to the near by point with 1.5 sqmm FRLS , PVC insulated copper wires, including necessary accessories and hardware's as required. (SD -563)

Supply and Laying of 3C x 2.5 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 3C x 2.5 sqmm COPPER cable LTUG cable with earth connection.

Supply and providing cable end termination of 3C X 2.5 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Supply and Laying of 4C x 6 sq.mm. PVC armoured copper LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 4C x 6 sqmm COPPER cable LTUG cable with earth connection.

Supply and providing cable end termination of 4 X 6 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Wiring with 2 x 4 sq.mm. (56/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point ( 8 points / Coil) Higher End (SD-385)

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour. ( SD 430

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS panel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

Supply, Installation, Testing and commissioning of 40 channel 8 SATA NVR, with 6T Hard Disk Drive 4 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency, Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces.

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behaviour analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. All including suitable camera stand and accessories. (Make: Dahua/Panasonic)

Supply and laying of CAT 6 armoured cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.complete. (Between ethernet switch to camera and radio modem i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply and Fixing of Rack with Accessories -Higher end 36 U Rack with LNS unit and fan extra for the above rack.

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2Hours back up

Supply, Installation, Testing & Commissioning of 100W LED fllod light with integrated driver including all specs as directed by the engineer in charge

P&C Projects Private Limited (BID ID -1116374)

SAKTHI ENGINEERS (BID ID -1116359)