Construction of Kodla to Andrehad road Km 0/000 to 5/500 (Package No. HP-02-328)

Amount

Excavation in hilly area in all heights and depths and in all kind of soil by manual/mechanical means including saturated soil comprising of ordinary soil, soft rocks, hard rocks, chiseling/wedging out of rock (where blasting is prohibited) and their intermediate classification of soil, setting out true to the required lines, grades, cutting and trimming of side slopes to level as shown in the drawing and as directed by engineer-in-charge at site according to the MORD technical specification clause 302, 304 & 1603 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of road and transportation of un-useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus material to required width of the road or on approved dumping sites through all modes of transportation including head load or animal transport or mechanical means along with its leveling, fine dressing and carriage of machineries, materials, tools, equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour if required. Recovery of stones to the tune of 22816.84 Cum quantity (twenty two thousand eighty hundred sixteen and paise eighty four ) cubic metres at the rate of 300/- (Rupees Three hundred) per cubic metre shall be effected from the contractor's running bills on pro-rate basis as per actual quantity executed. Any loss to the public, private property during the course of execution shall be the absolute responsibility of the contractor, which shall have to be duly compensated by him in all cases.

Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drain and Parapets etcetra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling /wedging out rocks (Where blasting is prohibited) as per drawings and M.O.R.D. technical specification section 300 and 1600 and as per direction of the Engineer- In – Charge including setting out, shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any lead and upto any lift including dressing of sides and bottom and back filling in trenches with excavated suitable approved material including shoring and strutting and pumping and bailing out water (surface and sub soil water ) upto any depth any quantam of water including cleaning of slush which may arises out during dewatering as per direction of Engineer-in-Charge. Including carriage of materials within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Back filling with granular material behind abutments, wing walls, return walls and retaining walls complete as per drawing and M.O.R.D. technical specifications clause 1203 and 1604 and as per direction of Engineer – in- Charge including carriage of materials within all leads and lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Construction of unlined surface drains of average cross-sectional area 0.40 sqm (Zero decimal foour zero square metre) in soil in all kind f soil to specified lines, grades, levels and dimensions as per MORDTechnical Specification Clause 307. as per direction of Engineer-in-Charge. Including carriage of materials within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete in foundation and plinth as per drawing and technical specification section 800, 90 and 1200 for nominal mix 1: 4: 8 (one cement isto four sand isto eight graded crushed/broken stone aggregate 40mm (forty millimeters) nominal size and curing complete including pumping or bailing out water, dewatering, removal of slush as required at site which may arise at the time of laying concretr complete for all heights/depths and including the cost of form work in retaining walls, breast walls etcetera as per the direction of Engineer-in-Charge and carriage of materials, within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete in foundation and plinth as per drawing and technical specification section 800, 900 and 1200 for nominal mix 1: 6: 12 (one cement isto six sand isto twelve graded crushed/broken stone aggregate 40mm (forty millimeters) nominal size and curing complete including pumping or bailing out water, dewatering, removal of slush as required at site which may arise at the time of laying under water complete for all heights/depths in R/wall and including the cost of form work in retaining walls, breast walls etcetera as per the direction of Engineer-in-Charge and carriage of materials, within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete in foundation and plinth as per drawing and technical specification section 800, 900 and 2600 for nominal mix 1: 4: 8 (one cement isto four sand isto eight graded crushed/broken stone aggregate 25mm (twenty five millimeters) nominal size and curing complete including pumping or bailing out water, dewatering, removal of slush as required at site which may arise at the time of laying concrete complete for all heights/depths and including the cost of form work in retaining walls, breast walls etcetera as per the direction of Engineer-in-Charge and carriage of materials, within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Random Rubble Stone masonry in cement-mortar 1:6 (one cement isto six sand) for substructure complete as per drawing & technical specification section 700 as per the direction of Engineer-in-Charge and carriage of materials, within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Construction of dry rubble masonry for retaining walls, breast walls, revetment walls and parapets etc. for sub structure and super structure complete as per drawing and technical specificationsection 700 as per the direction of Engineer-in-Charge and carriage of materials, within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying 100mm (Hundred millimeter) dia PVC pipe weep holes in brick masonry/stone masonry, plain reinforced concrete, Abutments, Wing walls, Return walls and retaining/breast walls extended through the full width of the structure with slope I(V):20(H)(One vertical : Twenty Horizontal) towards drainage face complete as per drawing and MORD technical specification Clause 709 and 1206.6 and as per direction of Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals.. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in open foundation for all type of structure complete using plain cement concrete grade M-10( M Ten) nominal mix 1: 3: 6 ( One cement : 3 sand : 6 graded crushed/broken stone aggregate 20mm (twenty millimeter) nominal size in or under water and curing complete in sub structure including pumping or bailing out water , dewatering removal of slush as required at site which may arrise at the time of laying concrete under water complete for all heights/ depths including the cost of form work as per drawings and M.O.R.D. technical specification section 800, 900 and 1200 as per the direction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and laying mechanically mixed and vibrated plain cement concrete grade M-15 (M-fifteen) design mix with cement contents not less than 275kg (two hundred seventy five kilogramme per cubic metre) in or under water including curing complete pumping or bailing out water de-watering removal of slush as required at site, which may arises at the time of laying under water complete for all heights/depths including cost of form work in Sub Structure i.e. parapets and other structure etcetra as per drawing and MORD technical specification section 800, 900 and 1200 including carriage of materials in all leads, lifts and other incidental, as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and laying rubble stone flooring for road work laid in cement mortar 1:3 (One cement : three sand) laid over including cement concrete bedding M-15 (M-fifteen) complete as per drawing and M.O.R.D. technical specifications setion 1300 including carriage of materials in all leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and laying mechanically mixed and vibrated plain cement concrete in road structure using plain cement concrete grade M-15 (M-Fifteen) nominal mix 1:2½:5 (One cement : Two and half sand : five graded crushed stone aggregate 40mm (Forty millimetres) nominal size) in or under water and curing complete including pumping or bailing out water complete for all heights/depths including cost of form work in craddle bedding under pipe culvert as per drawing and MORD technical specification section 800,900 and 1100 including carriage of materials in all leads, lifts and other incidental, as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Earth filling in foundation trenches as per drawing and technical specification section 300 and 1600 (For marshy soil) within all leads, lifts and other incidental, as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and laying (to level or slope) 900mm dia (Nine thousand millimeters) diameter reinforced cement concrete heavy duty non pressure pipes IS Class NP3 in single row including fixing collar with cement mortar 1 : 2 ( One cement : two sand) but excluding the cost of excavation, protection works, back filling, bedding concrete and masonry work in head walls and parapets as per drawing and M.O.R.D. technical specifications clause 1101 and as per direction of Engineer – in- Charge including carriage of materials within all leads and lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying of boulder apron laid in wire crates with 4 mm (four millimetre) dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm (one hundred millimetre into one hundred millimetre) mesh (woven diagonally) including 10 per (ten percent) cent extra for laps and joints laid with stone boulders weighing not less than 40 kg (forty kilogramme) each as per drawing and technical specifications Clause 1301. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing / errecting a " W" metal beam crash barrier composing of 3 mm (three millimetre) thick corrugated sheet metal beam rail, 70 cm (seventy centimetre) above road/ Grond level fixed on I.S.M.C. series channal vertical post 150 x 75 x 5 mm (one hundred fifty five into seventy five into five millimetre) spacer 2 m (two metre) centre to centre 1.8 m (one point eight metre) high, 1.1 m (one point one metre) below ground/ road level, all steel post and fitments to be galvanised by hot dip process. All fitting to conforms to I.S 1367 and I.S. 1364 metal beam rail to be fixed as the vertical post with spacer of channal section 150x75x5mm (one hundred fifty five into seventy five into five millimetre) and 330 mm (one hundred thirty millimetre) long complete as persection 811 of MORT&H specification (5th revision) as per the direction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Supplying fitting and placing HYSD bar reinforcement (Fe 415) in sub structure complete as per drawing and M.O.R.D. technical specifications clause 1000 and 1100 including cutting, bending, binding and placing in position complete in all respect including cost of binding wire upto any floor level as per the directions of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental . The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes GST imposed by the Government.

Supplying fitting and placing HYSD bar reinforcement (Fe-415) in superstructure complete as per drawing and M.O.R.D. technical specifications clause 1000 and 2400 including cutting, bending, binding and placing in position complete in all respect including cost of binding wire as per the directions of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete in sub-structure using grade M-20 ( M-Twenty) designed mix with cement contents not less than 330kg (three hundred thirty kilograms) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate as per drawings and M.O.R.D. technical section for Roads 800, 900 and 1200 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in sub structure i.e abutment and toe wall etcetra and curing complete including carriage of materials in all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in foundation using concrete grade M-20 ( M-Twenty) nominal mix with cement contents not less than 330 Kgs(Three hundred thirty kilograms) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate as per drawings and M.O.R.D. technical specifications for Roads section 800, 900 & 1200 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in bed block and culvertand curing complete including carriage of materials in all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete in super structure as per drawing and M.O.R.D. technical specification section 800, 900 and 1400 using Reinforced Cement Concrete grade M-25 (M-Twenty five) designed mix with minimum cement contents not less than 400 Kgs(Four hundred kilograms) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate and curing complete including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in deck slab of culvert etcetera including carriage of material within all leads, lifts and other incidental, as per the directions of the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing of typical PMGSY informatory sign board with logo as per M.O.R.D. specification and drawing . Three MS plates of 1.6 mm ( one point six millimeter) thick top and middle plate duly welded with MS flat iron 25mmx5mm ( twenty five millimeters into five millimeters) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (Twenty five millimeter into twenty five milimetres into five millimeter). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. ( Two Nos.) 75mmx75mm (seventy five millimeter into seventy five millimeters) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M fifteen) nominal mix 1:2½ : 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm(Forty milimetres) grade blocks of 450mmx450mmx600mm ( four hundred fifty millimeters into four hundred fifty millimeters into six hundred millimeters), 600mm ( six hundred millimeters) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm (Forty seven millimeter into forty seven millimeters) of 12 SWG (Twelve standard wire gauge) steel plate tube. All MS will be stove enamelled on both sides. Lettering and printing arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and M.O.R.D. technical specifications section 1701 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and erecting direction and place identification semi-reflective sign boards upto 0.90 sqm (zero point nine zero) size board, as per IRC-67 made of 2.0mm (two point zero millimeter) thick MS sheets duly stove enamelled paint in white colour in front and gray colour on back with red reflective border of 70mm (seventy millimetre) width and required message, letters and figures with reflective tape engineering grade as per clause 1701 of MORD for rural roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG (forty seven into forty seven millimetre of tewlve standard wire gauge) sheet square tube of 3050mm (three thousand fifty millimetre) height duly strengthened by 25mm x 5mm (twenty five millimetre into five millimetre) mild steel flat iron on edges on back firmly fixed to the ground by mean of properly designed foudation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeter) , 600mm ( six hundred millimeter) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidental . The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Reinforced cement concrete M-15 (M-fifteen) grade 5th (fifth) Kilometre stone (Precast) of standard design as per IRC :8-1980 fixing in position including painting and printing etcetera as per drawing and technical specification clause 1703 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads and lifts and other incidentals, labour and equipment required to execute the work to the site of work complete in all respect. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Reinforced cement concrete M-15 (M-fifteen) grade Ordinary Kilometer Stone (Precast) of standard design as per IRC :8-1980 fixing in position including painting and printing etcetera as per drawing and technical specification clause 1703 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads and lifts and other incidentals, labour and equipment required to execute the work to the site of work complete in all respect. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Reinforced cement concrete M-15 (M-fifteen) grade 200m (two hundred metre) Stone (Precast) of standard design as per IRC :8-1980 fixing in position including painting and printing etcetera as per drawing and technical specification clause 1703 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads and lifts and other incidentals, labour and equipment required to execute the work to the site of work complete in all respect. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing of Semi-reflective cautionary, mandatory and informatory sign board 600mm (six hundred millimetre) equilateral triangle as per IRC-67 made of 1.5 mm (one point five millimetre) thick MS-sheets duly stove enameled paint in white colour in fornt and gray colour on back with red reflective border of 65 mm (sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per Clause 1701 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG ( forty seven into forty seven millimetre of twelve Standard Wire Gauge) sheet square tube firmly fixed to the ground by mean of properly designed foundation with M-15 grade ( M-fifteen grade) cement concrete 450mm x 450 mm x 600 mm ( four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm ( six hundred millimetre) below ground level as per drawings and Technical Specification section 1701 including painting angle iron post with primer and two post of Epoxy paint as per specification and as per the direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing of Semi-reflective cautionary, mandatory and informatory sign board 600mm (six hundred millimetre) Circular as per IRC-67 made of 1.5 mm (one point five millimetre) thick MS-sheets duly stove enameled paint in white colour in fornt and gray colour on back with red reflective border of 65 mm (sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per Clause 1701 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG ( forty seven into forty seven millimetre of twelve Standard Wire Gauge) sheet square tube firmly fixed to the ground by mean of properly designed foundation with M-15 grade ( M-fifteen grade) cement concrete 450mm x 450 mm x 600 mm ( four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm ( six hundred millimetre) below ground level as per drawings and Technical Specification section 1700 including painting angle iron post with primer and two post of Epoxy paint as per specification and as per the direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and erecting direction and place identification semi-reflective sign boards upto 0.90 sqm (zero point nine zero) size board, as per IRC-67 made of 2.0mm (two point zero millimeter) thick MS sheets duly stove enamelled paint in white colour in front and gray colour on back with red reflective border of 70mm (seventy millimetre) width and required message, letters and figures with reflective tape engineering grade as per section 1700 of MORD for rural roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG (forty seven into forty seven millimetre of tewlve standard wire gauge) sheet square tube of 3050mm (three thousand fifty millimetre) height duly strengthened by 25mm x 5mm (twenty five millimetre into five millimetre) mild steel flat iron on edges on back firmly fixed to the ground by mean of properly designed foudation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimeter) , 600mm ( six hundred millimeter) below ground level as per approved drawings and technical specification clause 1701, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidental . The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

P/L Guard Stone on Curve made of Reinforced cement concrete local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification Clause 1704 as per specification and direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidental . The rate including octroi, royality, Malkana, toll tax GST, sale tax or other taxes imposed by the Government.

Earth work in excavation for all type of bridge structure in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling /wedging out rocks ( Where blasting is prohibited) as per drawings and MORTH technical specifications section 300and 2100Clause 304 and as per direction of the Engineer-Incharge by mechanical means/manual including setting out, construction of shoring and bracing , removal of stumps and other deleterious materials and disposal of materials upto any lead and upto any lift including dressing of sides and bottom and back filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150mm (one hundred fifty millimeters) compacted thickness including shoring and strutting and pumping and bailing out water (surface and sub soil water) upto any depth and any quantam of water including cleaning of slush which may arrise out during dewatering as per direction of Engineer-in-charge, including carriage of useful material or disposal of surplus materials within all leads and lifts and other incidental to the disposal site. The rate is inclusive octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing concrete for plain/reinforced concrete in open foundations Plain Concrete grade M-10 nominal size including bailing out water including curing and form work complete as per drawings and MORTH technical specifications section 1500, 1700 and 2100 and as directed by the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete in sub structure as per drawing and MORTH. technical specification Clause 1500 1700 and 2200 R.C.C. Grade M-25 (M-twenty five) designed mix with minimum cement contents of 344 kg. (three hundred forty four kilogrammes) per cubic metre with 20mm ( twenty millimeter) nominal size graded crushed stone aggregate and curing complete including cost of form work but excluding the cost of reinforcement for reinforced concrete work in abutment etc. as per the direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidential . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying reinforced cement concrete grade M-30 (M-Thirty) mix designed with minimum cement contents of 406 Kgs(Four hundred six kilograms) per cubic metre with 20mm(twenty milimetres) nominal size graded crushed stone aggregate (extra cement as per design mix above the minimum cement contents specified shall not be paid extra) in sub structure or under water and curing complete including pumping or bailing out water complete for all heights/depths as per drawings and MORTH technical specifications clauses 1500, 1700 and 2200 including cost of form work and staging in all heights complete in bed block and dirt wall as directed by the Engineer-in-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Supplying fitting and placing HYSD bar reinforcement in sub structure complete as per drawing and MORTH technical specifications section 1600 and 2200 including cutting, bending, binding, straightening and placing in position complete in all respect including cost of binding wire upto all height and depth as directed by the Engineer-in-charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying filter media with granular crushed aggregate as per specification to a thickness of not less than 600mm ( six hundred millimeter) with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing walls return walls and retaining/breast walls to the full height compacted to firm condition complete as per drawing and MORTH technical specifications section 2200 and clause 710.1.4 of IRC-78 and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Supplying, fitting and fixing in position true to line and level cast steel rocker bearing conforming to IRC: 83(Pt.-1) section IX and clause 2003 of MoRTH specifications complete including all accessories as per drawing and MORTH technical Specifications and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Supplying, fitting and fixing in position true to line and level forged steel roller bearing conforming to IRC: 83(Pt.-1) section IX and clause 2003 of MoRTH specifications complete including all accessories as per drawing and MORTH technical Specifications and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Steel work revetted in built up sections including cutting, hoisting, fixing, in position and launching of site of work including complete arrrangement of form work staging launching pad etc. in all height and depth and applying a priming coat of red lead paint in trussed steel bridges as per MORTH technical specificastion section 1900 and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Furnishing and placing reinforced pre-stressed mechanically mixed and vibrated cement concrete in super-structure as per drawing and technical specification RCC Grade design mix to obtain minimum compressive strength of grade M-30 (M-Thirty) using minimum cement contents of 406 Kgs (Four hundred six kilograms) per cubic metre with crushed stone aggregate 20mm (Twenty millimetres) nominal size(extra cement as per design mix above the minimum cement contents specified shall not be paid extra) including form work and staging in all heights and curing complete in deck slab and ridgeas per drawings and MORTH technical specification section 1500, 1700 and 2300 as directed by the Engineer-in-Charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanical mixed and vibrated cement concrete M-15 (M-Fifteen) with minimum nominal mix 1:21/2:5 (One cement isto Two and half sand is to five graded crushed/broken stone aggregate 40mm (Forty millimetres nominal size) levelling course below approach slab complete including cost of form work and curing complete as per drawing and MORTH technical specifications clause 2100 and 2700 and as directed by the Engineer-In-charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete grade M-30 (M-Thirty) mix design with minimum cement contents of 406 Kgs (Four hundred six kilograms) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate (extra cement as per design mix above the minimum cement contents specified shall not be paid extra) in approach slab including cost of form work and reinforcement complete with bending, binding, placing in position of bars with cost of binding wire as per drawings and MORTH technical specifications section / clause 1500, 1600 1700 and 2704 and as directed by the Engineer-In-charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and Layinfg 50mm (Fifty milimeter ) thick mastic asphalt wearing couures on top of deck slab using paving grade bitument VG-30 meeting the requirements given in table 500-39 including roughening of surface with wire brush, cleaning the surface , applying a thin bituminous tack coat of VG-30 grade bitumen @ 0.325 Killogram per squre meter after applying tack coat fixing chicken mess reinforcement of 1.50mm ( One Point Five millimeter ) dia steel wires with hexagonal or rectanngular opening of 20-25 mm befor pouring mastic asphalt perpad using mastic cooker for heating coarse aggregate, Fine aggergate , filler and bitumen as per Clause 516 of MORD specification ,laid t required level and slope including providing antiskid surface with a layer of hard stone sggregate 13.2mm (Thirteen Point two millimeter ) of 9.50 mm (Nine point Five millimeter ) nominal size as per direction of the Engineer-in- Charger precoated with VG-30 grade bitimen applid at the rate of 0.005 cum (Zero point zero five cubic meter ) per 10 (ten) square meter and rolled or pressed in to surface at approximate spacing of 10cm (Ten centimeter ) center to center in both direction , when the temperature of surface is not less then 100 degree centigrade protruding 1 mm to 4mm (One millimeter to four millimeter ) overmastic surface complete in all respect as per specification including carriage of material with all leads and lift and other incidental The rate is including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Supplying fitting and placing HYSD bar reinforcement in super structure complete as per drawing and MORTH technical specifications section 1600 and 2300 including cutting, bending, binding, straightening and placing in position complete in all respect including cost of binding wire upto all height and depth as directed by the Engineer-in-charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing drainage spouts complete with 100mm ( one hundred millimetre ) dia galvanized mild steel down pipe corrosion resistant structural steel grating complete as per drawing and M.O.R.T.H. technical specifications clause 2705 and as per the direction of Engineer-in- Charge including carriage of materials within all leads , lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Construction of Reinforcement cement concrete railing of M-30 grade (M-thirty) in cast in situ with 20mm (twenty millimetre) nominal size aggregate true to line and grade , tolerance of vertical railing post not to exceed 1 in 500 (one in five hundred) centre to centre spacing between vertical posts not to exceed 2000 mm (two thousand millimetre) leaving adequate space between vertical post for expansion complete including the cost of reinforcement, form work and curing complete as per approved drawing and MORTH technical specifications section 2700, 1500, 1600 and 1700 and as per the entire satisfaction and as directed by the Engineer-in-charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying expension joint catering meximum horozontal movement up to 40mm (Forty millimetre) complete as per draeing No. PW/CE-N/bridges (standrad)9-/107-2-R1) and MORTH specification section 2600 andthe direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidental . The rate including octroi, royality, Malkana, toll tax, sale tax GST or other taxes imposed by the Government.

Providing and filling joint sealing compound as per drawing and M.O.R.D. technical specifications clause 1207.2.2 with coarse sand and 6% ( Six percent) bitumen by weight complete in all respect as per drawings, design and the direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidental . The rate including octroi, royality, Malkana, toll tax, sale tax GST or other taxes imposed by the Government.

Providing and laying in position 20mm (Twenty milimetres) thick pre-moulded joint filler in expansion joint for fixed ends of simply supported spans covered with sealant complete as per drawing and M.O.R.D. technical specifications section 2600 complete in all respect including carriage of material within all leads, lifts and other incidentals as per the entire satisfaction and direction of Engineer – in- Charge The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Loosening of the ground upto a level of 300 mm (three hundred millimetre) below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.1 and 300.2 for subgrade construction as per Technical Specification Clause 303.5.2. as per direction of Engineer-in-Charge. Including carriage of materials within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading by mechanical means to required slope and compacted with three wheel 80-100 (eighty - hundred) kN static roller to meet requirement of Table 300.2 complete as per MORD technical Specification Clause 303 and as per direction of Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals.. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Construction of granular sub-base by providing well graded materials, mixing in mechnicalmix plant and carriage of mixed materials to site of work in all leads and laying in uniform layers with Motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth Wheel 80-100 (Eighty-hundred) kN static roller to achieve the desired density, complete as per Technical Specification Clause 401 for grading-I Material, as per the entire satisfaction and directions of Engineer-in-Charge within all leads and lifts and other incidentals. . The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing, laying, spreading and compacting stone aggregate of size 63mm to 45mm ( sixty three millimeter to forty five millimeter) Grading-II [75mm ( seventy five millimeters) consolidated thick] to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 K.N. static roller in stages to proper grade and camber applying and brooming, stone screening type-B of size 11.2mm ( eleven point two milimetres) nominal size at the rate of 0.20 cum ( zero point twenty cubic metres) per ten square metres and binding material at the rate 0.06 cum ( zero point zero six cubic metre) to fill up the interstices of coarse aggregate, watering and compacting to the required density as per M.O.R.D. technical specifications clause No. 405 and as per the entire satisfaction and direction of Engineer – in- Charge including carriage of materials within all leads and lifts and other incidental The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing, laying, spreading and compacting stone aggregate size 53mm to 22.4mm ( fifty three millimeter to twenty two point four millimeter) Grading-III [75mm( seventy five millimeters) consolidated thick] to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 K.N. static roller in stages to proper grade and camber, applying and brooming, stone screening type-B of size 11.2mm ( eleven point two milimetres) nominal size at the rate of 0.18cum ( zero point two eighteen cubic metres) per ten square metres and to fill up the interstices of coarse aggregate, watering and compacting to the required density as per M.O.R.D. technical specifications clause No. 405 and as per the entire satisfaction and direction of Engineer – in- Charge including carriage of materials within all leads and lifts and other incidental . The rate includes octroi, royality, Malkana, toll tax, sale tax or GST other taxes imposed by the Government.

Providing and applying primer coat with BITUMEN emulsion (SS-1) on the prepared surface of granular base including cleaning of road surface with hydraulic brooms and spraying primer @ 0.850 Kg. per Sqm. (Zero point Eight five zero kilogram) per square metre using mechanical means as per M.O.R.D. technical specifications clause No. 502 including carriage of material within all leads, lifts as per the entire satisfaction and direction of Engineer – in- Charge and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.275 kgs. (Zero point two Seven five kilograms) per Square metre on the prepared granular surfaces treated with primer and cleaned with hydraulic broom as per M.O.R.D. technical specifications clause No. 503 including carriage of material within all leads, lifts and other incidentals as per the entire satisfaction and direction of Engineer – in- Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying 30mm (thirty milimetres) thick bituminous concrete with 100-120 TPH batch type HMP (Hot Mix Plant) producing an average output of 75 tonnes (Seventy five) tonne per hour using crushed aggregates of specified grading, premixed with bituminous binder VG-10 (Viscosity grade-Ten) @ 5.5 % (Five point five) percent of weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 507 complete in all respect and as directed by the Engineer-in-charge including carriage of material within all leads, lifts, height and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.