TCMC - Repair and Maintenance of UGSS,Water Supply Motor, Starters and Generators in Zone II

Amount

Removal and Refixing of centrifugal purnpset/Jet pumps/submersible pumpsets and its accessories from borewellj open well for attending repairs 50% of the rates mentioned under item 17 (a), 17 (b) and (c) may be allowed for the respective

Removal servising and recondition of Belt typr and Mono Type Air compressot Pump including all material and Labour charges etc complete

Submersible Pumpset Removal and Refixing of Submersible Pumpset Upto 2 HP

Submersible Pumpset Removal and Refixing of Submersible Pumpset Upto 3 to 5 HP

Submersible Pumpset Removal and Refixing of Submersible Pumpset Above 5 HP to 10 HP

Submersible Pumpset Removal and Refixing of Submersible Pumpset Above 10 HP to 20 HP

Oil Seal Changing /Ball Bearing / Servicing Upto 2 HP

Oil Seal Changing /Ball Bearing / Servicing Upto 3 to 5 HP

Oil Seal Changing /Ball Bearing / Servicing Above 5 HP to 10 HP

Oil Seal Changing /Ball Bearing / Servicing Above 10 HP to 20 HP

Coil Rewinding centrifugal Above 5 HP to 10 HP

Coil Rewinding centrifugal Above 10 HP to 20 HP

Coil Rewinding Submersible Upto 2 HP

Coil Rewinding Submersible Upto 3 to 5 HP

Coil Rewinding Submersible Above 5 HP to 10 HP

Coil Rewinding Submersible Above 10 HP to 20 HP

capacitors range 80 mfd to 120 mfd

capacitors range 35 mfd to 40 mfd

Supply and fixing of following Three phase contactor and over load relay replacing capacitors and Ammeter etc including all labour charges

contactor range 25 A

contactor range 35 A

contactor range 45 A

contactor range 60 A

OLR Range 5 to 10 A

OLR Range 10 to 20 A

OLR Range 20 to 30 A

40mm HDPE Hose

40mm HDPE SS Coller /40mm HDPE Hose Clip

32mm HDPE Hose

32mm HDPE SS Coller /32mm HDPE Hose Clip

20mm PVC Tap

32mm G.M.Gate Valve

3core 6Sqmm Flat Cable

3core 4 Sqmm Flat Cable

Supply and Fixng of Single Pole 6A to 32A, 10KA MCB

Providing Routine Annual Service Maintenance of DC Generator requires periodic cleaning, lubrication, inspection of brushes and commutator, and testing of brush spring tension. In addition, the electrical connections need attention to ensure clean metal to metal contact and tightnes. Visually and manually inspect the condition of all cables,clamps, wiring and terminal connections. See the generator drive pulley is tight on the shaft and that the belt is in good condition and adjusted properly. etc complete Rates are only for Labour exept materials

200 to 100 KVA Gen-set

63 to 15 KVA Gen-Set

Removing, Repairing and Re-fixing of following capacity of Non Clog Submersible Sewage Pumps for replacing of Starter winding by F class insulation and improving insulation value of the rotor coil with proper balancing, mechanical seal top and bottom replacing of Ball Bearing top and bottom, ‘O’ Ring and fasteners, Impeller shaft and key Assembly and Terminal blocks and Cables etc,.complete

5 HP Non Clog Submersible Motor

7.5 HP Non Clog Submersible Motor

10HP Non Clog Submersible Motor

15 HP Non Clog Submersible Motor

50 HP Non Clog Submersible Motor

70 HP Non Clog Submersible Motor

120 HP Non Clog Submersible Motor

VIJAY ELECTRICALS (BID ID -1091195)