CONSTRUCTION OF STUDENTS OFFICERS MESS AT MINTSD UNDER GE(SOUTH) PUNE

Amount

SCH 'A' PART-I: BUILDING/STRUCTURES Note: This schedule is not pre-priced by MES and the rate indicated as "Rs 0.00" under Col 6 signifies this fact only

Construction of Block of Students Officer's Mess including Servant Quarters (12 Nos) complete all as shown in drawings and as specified.

Construction of Block of Servant Quarters for 20 servants complete all as shown in drawings and as specified.

Construction of Block of Sentry Box Type 'A' complete all as shown in drawing No. CEPZ/91/TD/21M sheet 1/1 and as specified.

Construction of Underground sump 25000 liters (5500 Gallons) capacity complete all as shown in drawing No. CEPZ/99/TD/5/STR sheet 1/1 and as specified.

Total amount of Sch ‘A’ Part II (Internal Water supply)

Total amount of Sch ‘A’ Part III (Internal Electric Supply)

Total amount of Sch 'A' Part-IV (Road, Path, Culverts and hard standing)

Total amount of Sch ‘A’ Part V (Area drainage)

Total amount of Sch ‘A’ Part VI (Sewage Disposal)

Total amount of Sch 'A' Part-VII (Compound walll/ Fencing and gate)

Total amount of Sch 'A' Part-VIII (External water supply)

Total amount of Sch 'A' Part-IX (External Electrification)

Total amount of Sch 'A' Part-X (Dismantling/Demolition)

Total amount of Sch 'A' Part-XI (Site clearance, excavation and earthwork)

NOTE: Schedule ‘A’ Part II to XI items which are not Prepriced by MES, Bidders shall insert their rate in Column-6 only and the Estimated rate indicated as "0.0" are for that purpose.

SCHEDULE 'A' PART-XII (MISC B/R AND E/M WORKS)

Supply and Fix air cooled split unit air conditioner electric driven,single phase of capcity of 1.5 TR BEE, 5star rated.

Supply And Fix air cooled split unitair conditioner electric driven,single phase of capcity of 2 TR BEE, 5star rated.

Supply And Fix air cooled split unitair conditioner electric driven,single phase of capcity of 1 TR BEE' 5star rated.

S&F voltage stablisers for automatic operation,single phase naturally air cooled type and designed for input variation between 170V to 250v with output voltage at 230v with accuracy of +/- 2.5% and of capacity 4.0 KVA

S&F voltage stablisers for automatic operation,single phase naturally air cooled type and designed for input variation between 170V to 250v with output voltage at 230v with accuracy of +/- 2.5% and of capacity 5.0 KVA

Supply, Install, testing and Commissioning of 'Solar Hot Water System Flat Plate Collector type, based on indirect transfer of heat of capacity 100 LPD with electrical heating backup of 3 KW heating eleament and thermostat, stainless steel hot water tank duly insulated,self supported on MS angle iron structure and suitable size hot water /steam valve complete all as specified and as directed.

Supply and fix refrigerator electric driven single phase of capacity 330Litre

Supply and fix deep freezer,double door, glass top of capacity 400 Ltr electric driven single phase.

Supply , installation and commissiong water cooler electric driven (single phase) having approx storage capacity of 120 liter and normal cooling capacity of 60 liter per hour.

Supply,install, testing and commissioning centrifugal monoblock pumpset mounted on base frame, with electric driven motor,3 phase, 4 wire,50 cycles,440 Volts, suitable HP with discharge of 2.03 lps a head of 20 metres, directly coupled including brass impeller, connecting to suitable size suction pipe and discharge pipe,connection from sump to pump an pump delivery to main header coupling guard, pressure gauges at delivery side, air release valve, CI foot valve of suitable size and iron base frame with nuts,bolts complete for mounting pump set and all accessories as recommended by manufacturer,PCC foundation, rubber pads complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode size 600 mm x 600 mm x 6.3 mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanized earth lead 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized including GI protection pipe medium grade 15mm dia connected to main earth wire on pole or control board and GI pipe medium grade 20 mm dia bore for watering funnel with wire mesh. RCC cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion

S&F thermoplastic cable junction box with weather proof for out door installation IP 66/67 protection grade of two terminals suitable for cable entry 10 -25 sqmm of size 205x255x112mm including necessary clamps for fixing arrangement complete all as specified and directed. Make Hensel Cat No KF2525G

Supply installation, commission and testing of outdoor type Feeder pillar box Outdoor type,compartmentalised made out of CRCA sheet 3.15 mm thick (width of panel shall not be less than 60 cm in any respect ) with powder coated painting and four Nos 200 amps Aluminiumstrip/bars ( not less than 65 mmx10 mm duly insulated mounted on insulators /suitable size backelite sheet ) mounted on angle iron frame of made out of 40mmx6mm angle ironand comprising the following:-

(a) MCCB 4pole 200 Amp,415 volt , 25 KA,with thermal magnetic variable setting protection (overload &short circuit protection)-1No .(main incoming )

(b) ditto but outgoing MCCB ,4 pole, Ics = 100 % Icu with thermal release range 40A =01 no(for bldg supply )

(c) -do- but outgoing MCCB 4 pole,16KAIcs = 100 % Icu with thermal release range range 80A=01 N0(for AC supply)

(d) MCB TPN 10A,C series mounted on DIN channel=02Nos(For High masts)

(e) MCB TPN 16A,C series mounted on DIN channel=01Nos(for street lights and gate lights)

(f) MCB TP 16A,C series mounted on DIN channel=02Nos(for bollard two circuits)

(j) LED phase indicating lamps(red,yellow,Blue)=01 SET

M& L for garden lights in decorative LED fixture,aluminium die casting,polycarbonate frosted diffuser grey colour,IP65 and IK-07 all as specified and directed

M&L for Gate Lights in MS housing with PU paint,top canopy made of spun aluminium,IP65 IK-10 rated of wattage 30watt mounted on MS round pipe of dia 32/40mm all as specified and directed

Supply and fixing integral LED street light luminaire 35 W comprising of epoxy powder coated housing enclosed with glass cover in frame suitable for 40 mm GI pipe complete with accessories Complete all as specified and directed. Make : Wipro/Philips/Bajaj/Havells/Crompton.

Supply, install, testing and commissioning transformer, outdoor type HT 22 KV, 3 PH, LT 433 , 4 wire, capacity 100 KVA copper wound, oil cooled, vector symbol Dyn-11, HV-delta, LV- Star connected complete with all standard fitting as per IS : 1180. HT bushing and LT side cable box with off load type tap changer hand operated having taping at HV for variation + 2.5% to + 7.5%, 5 nos in equal steps of + 2.5%, temperature rise in permitted oil/inding by self-resistance method at normal ratio 45⁰C with first filling of transformer oil of suitable dielectric strength as per IS: 1180 Part-I 2014 Level III all as specified and directed. The transformer shall be provided with and including following accessories : -

(a) HT/LT bushings with cable Box

(b) LT Neutral Bushing to be brought out separately for solid earthing.

(c) Conservator complete with oil filling hole with cap and drain plug, oil level gauge

(d) Silica gel dehydrating breather with pre filled silica gel.

(e) Off load tap changer. (h)Explosion vents diaphragm. (i) Thermometer pocket with thermometer of range 0-70 degree Celsius.

(h) Explosion vents diaphragm

(i) Thermometer pocket with thermometer of range 0 - 70 degree celsius

(j) Air release plug.(k) Filter valve with plug (suitable for ratings).

(k) Filter valve with plug (Suitable for ratings)

(l) Rating & diagram plate. (m)Drain valve with plug. (n) Earthing terminal.

(m) Drain valve with plug

(n) Earthing terminal

(o) Plain rollers - 4 Nos.

(p) Lifting hooks

(q) Transformer plinth with PCC 1 : 3 : 6 type C - 2 of size 1.5 m x 1.5 m x 1.8 m (ht) complete including slant slot for accomodating 100 mm dia pipe on both LT & HT side with clamping arrangement as per manufacturer instructions complete,as per drg approved all as specified and directed

(r) Initial filling to transformer oil.

Supply and laying, testing and commissioning of HT Underground XLPE insulated, screened PVC bedded galvanized steel strip armoured electric power cable (heavy duty) with aluminium conductor 22 KV grade(Earthed) of 150 sqmm 3 core cable comfirming to IS-7098 Pt-II cable laid in trenches/walls/ducts/poles complete all as specified and directed.

M & L for switch air break gang operated triple pole mechanically operated mounted on HT insulators horizontal type and ms galvanized steel frame with operating mechnizing worked from ground level including operating rod of size 32 mm dia /25 mm dia as reqd GI medium grade for current rating upto 400 Amps 22000 volts complete with locking arrangement ,ms clamps ,bolts ,nuts and washers etc.including two coat of aluminium paint over a coat of red oxide primer on ms work complete all as specified complete all as specified and directed.

Supply and fixing HT cable route/joint indicator made of Cast iron fixed in PCC block cast in situ of size 0.2x0.2x0.3mtr on MS angle iron of size 40 x40 x 5 mm with nut, bolt & washers of suitable size.

M&L for end termination, out door type with and including suitable size of cold shrinkable new end connection jointing kit 22000 voltage grade and aluminium lugs duly crimped with crimping tool for the cable size of HT 150 sqmm XLPE cable.

M&L for HT bus bar for 2/4/6 pole structure made out of aluminium tube having outer dia 32 mm and 06 mm thick suitable for 22 KV complete with all suitable joints with S S nut bolts etc and colour sleeve as per colour code incl aluminium strip 25x4 mm of reqd lengh for jumpering purpose all as specified and directed

Supply and fixing lightning arrestor non linear type with mounting accessories complete fixed on cross arms of pole and connected with aluminium conductor with all fittings transmission class earth system, having discharge capacity of 10 Kilo amps and suitable for working pressure of 22 KV grade all as specified and directed

Supply, install test and commissioning of automatic intelligent power factor corrector (APFC) capacitor bank panel LT 3 phase 440 volts system 50 Hz AC supply to improve PF to unit automatically, step wise capacitor panel floor mounted, outdoor type .weather proof dust/vermin proof made out of MS sheet 3.15mm thick with inner compartment sheets 1.6 mm thick and angle iron 40mmX40mmX6mm frame factory made fabricated as modular in construction duly powder coated light grey colour, front openable panel shutter with locking arrangement to facilitate easy for maintenance, natural air cooled cable entry with gland plate with provision of PCC 1:3:6 type C-1 ,450 mm below ground and 450 mm above ground level all around legs complete of capacity 40 KVAR comprising of the following including necessary excavation and earth work :-

(b) Naturally air cooled MPP double dielectric heavy duty 440 volts LV 50 HZ shunt power capacitor conforming to IS - 13340 and 13341 and IEC - 831 - 1 ISI marked designed on ambient temperature 10 degree to 50 degree Celsius delta connections complete with metal base enclosure copper wire connections for banking complete of GE POWER EPCOS make with watt loss not more than 5 watt /KVAR complete no of stepping combinations of 2+3+5+5+5+10 +10(9steps) KVAR each or as directed by Engr - in - charge.

(c) Internal wiring with adequate size of PVC insulated copper HR multistranded cable with necessary lugs, thimbles/gland - 01 job.

(e) Each bank shall be protected with MCB of suitable rating.

(f) Aluminium bus bar of capacitr 100 Amp for three phase and neutral shall be provided with epoxy base.

(g) Incoming : MCCB 63 Amps, 25 KA, TPN, 415 volts - 01 no

(h) Each capacitor is provided with capacitor duty contactor of suitable size incl indicator lamp and push on switch

Supply and fixing of drop out fuse assy single pole 22 KV , 200 Amps rating complete expulsion fuse element mounted on four /two pole structures all as specified and directed.( Necessaty Nut, bolt and washers should be included in above quoted rate)

Taking down old unserviceable gate lights of any size and type all as directed

Taking down old unserviciable garden lights of any size and type all as directed

Taking out unserviceablev LT cable of sizes

S&F post top insulators pin type ceramics/polymer suitable for working voltage of 22KV all as specified and directed

Supply , installation ,Testing and commissioning of Galvanized steel high mast lighting system of 16 meter in two section, 3 mm section thickness, top dia 150 mm, bottom dia 340 mm, with 2/3 wire rope system and its accessoriesHot dip galvanised both inside & outside conforming to IS 4759-1984,IS-2629-1985,IS2633-1972 . System is suitable for loading 08 nos 80 to 150w LED lights with power tool for automatic raising and lowering of lantern carriage all as specified and directed ( Supply and fix foundation bolts manufactured from special steel along with nuts,washers,anchor plates , templates, incl High mast foundation as per manufacturer recommendation ,Aviation obstruction luminaire ,Outdoor electrical panel are included in unit rate all as specified and directed

A) High Mast structure (i) Height of Mast : 16 Mtrs

(ii) Material of Construction : As per IS 5986

(iii) Thickness of Material Top Section : 3 mm Bottom Section : 4 MM

(iv) Cross section of Mast (Number of Sides) : 20 sided polygon

(v) Length of Individual section : Top Section : 8.25 Mtrs : Bottom Section : 8.25 Mtrs

(vi) Base and Top Diameter : Top : 150 MM : Base : 360 MM

(vii) Metal Protection Treatment for Mast section : Hot dip Galvanised as per BS 729

(viii) Size of door opening at base of mast : 1200mm x 300mm with locking arrangements.

(ix) Lighting Protection : GI Single spike of length 1200 MM

(x) Size of Base Plate : Diameter 540 mm, Thick 25 mm

B. Lantern Carriage (i) Material of construction : 50 NB ERW class B MS Pipe

(ii) Diameter of lantern carriage ring : 600 MM (ID)

(iii) Construction : 9 arm welded

(iv) Number of Joints : 2 segment/ 3 segment

(v) Load carrying capacity : 9 Luminaire, symmetrical

C) Winch (i) No Of drum Per Winch : Double Drum

(ii) Gear Ratio : 53 :1 or 50 : 1

(iii) Capacity : SWL 750 Kg

iv) No of SS rope : 3 Nos of 6mm for lantern carriage : 2 Nos of 6 mm for double drum winch

(v) Breaking capacity : 2350 Kg per SS wire rope

D) Stainless steel wire rope (i) Grade : AISI 316

(ii) Diameter of SS rope : 6 mm

(iii) Construction of SS rope : 7/19

(iv) No of SS rope : 3 Nos of 6mm for lantern carriage : 2 Nos of 6 mm for double drum winch

(v) Breaking capacity : 2350 Kg per SS wire rope

E) Trailing Cable (i) Type : Flexible copper 5 core copper, EPR Insulated PVC Sheathed

(ii) No of circuit per Mast : One

F) Power Tool (i) Model : Integral

Supply and fix LED flood ligh fittings pressure die cast housing, highly efficient, heat resistance tempered glass for protection suitable for highmast of capacity 200watt , 230 volt 50 Hz AC supply complete as per Phillips Cat No. BVP122 LED 146 CW FLNB FG XTFC or of equivallent make in Crompton / Wipro

M&L for earthing complete with galvanized steel earth plate electrode size 600 mm x 600 mm x 6.3 mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanized iron strip 32mx6mmmeans of bolts, nuts, check nuts and washers of galvanized including GI protection pipe medium grade 40mm dia connected to main earth wire on pole or control board and GI pipe medium grade 20 mm dia bore for watering funnel with wire mesh. RCC cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion.

Supply,install,testing and commissioning of Diesel Engine Generaing Set, 62.5 KVA,1500 RPM, 3 phase,415 V,50 c/s, power supply alternator along with fuel tank,control panel,battery and complete set installed in sound acoustic enclosure and standard accessories and fittings,with power factor 0.8,PCC foundation suitable for the generator set as per manufacturer's instructions,tools and spares complete all as specified and directed and comprising of the following:-

a) Engine:Diesel engine,6 cylinder engine developing 83 BHP @ 1500 RPM for continuous duty of suitable for 62.5 KVA alternator with provision of 10% over load for one hour in every 12 hour running confirming to BS 5514/ISO 3046 standard Totally enclosed,electric star,compression ignition,4 stroke.The engine shall consists of following specification:-

(i) Fly wheel to suit flexible coupling with starer ring,cooling radiator with blower fan,fuel houses,mico fuel pump with mechanical governor,oil bath type air cleaner,exhaust silencer,SS expansion bellow,lubricating oil fitler,fuel oil filter,12V electric starting system,battery charging alternator,engine control panelcosisting of ON/OFF START key,lub oil pressure guage,water temp guage,ammeter basttery charging safely divices such as:low lubricating oil pressure,light water temperature ect as per standards.

(ii) Instrument panel consisting of: Starting switch with key lubricating oil,temperature guage,lubricating oil pressure gauge, water temperature guage,battery charging indicating lamp,hour meter with RPM indicator,safety control against high temperature of water,over speed stop with double driver adopter.

(iii) Alternator: Self excited self regulated,floor mounted with all and / or roller bearings, statically and dynamically balanced screen protected SPDP enclosures confirming to IS 4722 / BS 2613,single shaft extensive type with damper with damper winding on pole ‘F’ class insulation automatic voltage regulated from no load to full load,ammeter capacity of delivery 62.6 KVA,415 volts,3 phase,50cycles and lagging for AC supply and will be suitable for tropical conditions.

(b) OTHER FITTINGS:(i) Battery Charger : Battery charger having electric circuit consisting of rectifiers, capacitors and resistance etc. The battery charger should be able to charge 12 volts 180 AH battery 2 Nos at a time

(ii) Fuel tank of suitable capacity as per manufacturer recommendation mounted on steel frame at suitable height with all connecting pipes and fittings upto fuel pump and over flow pipe from engine to tank including level indicating gauge duly marked and drain valve and air vent plug etc.

(c) DG set shall be supplied along with acoustic original enclosure of the manufacture’s suitable for 62.5 KVA DG Set as per CPCB Norms

(d) The DIESEL OIL, LUB OIL etc. for smooth functioning of DG SET during PH-I& PH-II complete testing and full tank filling of DIESEL OIL after PH-I & PH-II testing, topping of LUB OIL etc. required for commissioning and testing of DG set.

(e) Maintenance Spares: - (i) Lub Oil filter elements - 05 Nos

(ii) Fuel filter element - 05 Nos

(iii) Vee Belt set- 02 Sets

(iv) Air cleaner element - 01 Set

(v) Flexible coupling for Gen set - 01 No

(vi) Battery 12V 120 AH-01 No

(e) Excavation, earthwork and provn of PCC plinth of suitable sizes for installation of DG set & connected accessories complete.

Supply and fixing punched typecoil(PTTG) 610mm dia having 50 turns and approx weight 8.75Kg +/- 5% and streches to cover a distance of 5-7 meter complete all as specified and directed.

Supply and fixing blanking plate of PVC made.

S&F LED light fitting 1 x 20 watt, 220 volts,AC Decorative box type with driver holder including LED tube lifht connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed, Make Havells part No INDURALINEARNEOBS20WLED865SPCWH or equivalent model in the makes Philips/Bajaj/Crompton/Wipro

S & F of LED light fitting out door type Building security light 25W to 30W fixture consist of Extruded Aluminium Extrusion housing with PC Diffuser, LED Fixture System wattage of 36W /40W, 140V - 260V AC, System Lumen Output min 3960 Lumen in 36W or 4400 lumen in 40W with 5700 - 6500 K CCT with pf > 0.95, CRI >=80 and with < = 10% THD, with min 2.5 KV Surge protection in Built and complete LED fixture with BIS R mark and R Registration no. All as per Philips Cat No SM 365C LED 32-6500 PSU OD WH or Havells Cat Part No. ENDURAPEARLSL25WLED 757SASY TOPC or or equivalent model in the makes Philips/Bajaj/Crompton/Wipro with and including brackets made of 40mm dia GI tubung light grade bent to shape required includnig 2 Nos of Flat Iron brackets duly welded with nuts, bolts and washers.

S & F 2' x2' grid ceiling outdoor type recess 36w-40w ceiling mounted bottom opening LED cleanroom fitting including LED fixture powder coated CRCA housing and polycorbonate diffuser, LED fixture system wattage of 36w to 40w, 140-260V AC, system Lumen output min 3600 Lumen in 36 W or 4000 Lumen in 40W, with 5700-6500 K CCT with PF>0.95 CRI>=80 and with <=10 % THD, with Min 2.5 KV Surge protection in Built and complete LED fixture with BIS Mark and R Registration no. of Havells Cat Part No. VENUSNEOHE2X2PLP18-42WLED865MOD or equivalent model in the makes Philips/Bajaj/Crompton/ Wipro and shall conirm all above specification of respective suitable Cat reference.

S&F LED light fitting 1 x 11 watt, 220 volts,AC Decorative box type with driver holder including LED tube lifht connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed, Make Havells part No INDURALINEARNEOBS10WLED865S PCSS or equivalent model in the makes Philips/Bajaj/Crompton/Wipro

S & F electronic meter 3 phase , 415 Volt, temper proof LCD display with polycarbonate cover 230V, 10-60 Amp , accuracy class -I 50Hz , conforming to IS13779, IP 54,,with parameters to show data , time current reading , load ,PF voltage and KWH.

Supply and fix bib tap 15mm bore long body suitable for kitchen sink, cast copper alloy with crutch or butterfly handle , screwed down , screwed for iron pipe or for brass ferrule and fixed.

Supply and fix two way cock CP,suitable for 15mm dia pipe with wall flange complete in all respect all as specified .

Supply and fix brass CP wall mixer 3-in-1 for mixing hot and cold water srewed down for iron pipe & fixed complete in all respect all as specified .

PROVISIONAL SUM Provide Provisional Sum for :- (a) Rain Water Harvesting (Refer Annexure 'A' for brief scope of work) (b) PCC Hardstanding (240 Sqm) as specified at srl No. 'F' in Schedule of Finishes Drawing No. CEPZ/2021/PN/02 Sheet 19R/19. NOTE for (a) and (b): Excavation and earthwork shall be measured & paid under Schedule 'A' Part XI (Site clearance, excavation and earthwork).

United Sales Corporation

Shree Constructions

N. H. Saluji & Associates

surendra infrastructure pvt ltd